User Manual UPI-ST interface
Contents
1. interface Make sure the cable towards the UPC 100 Handset is connected If your problem is not listed try the FAQ section on www ums sg 10 Transport When transporting the UPI ST Interface make sure it is not connected to the UPC 100 Handset The cables towards the truck must also be disconnected to prevent damage 11 Regulatory compliance This UPI ST Interface complies with the Electromagnetic Compatibility Directive 2004 108 EC in particular with the harmonized standards listed below Emission EN 55022 2006 A1 2007 class B Immunity EN 55024 1998 A1 2001 A2 2003 Emission EN 61000 3 2 2006 Emission EN 61000 3 3 1995 A1 2001 A2 2005 12 Warranty UMS warrants the UPI ST Interface for a period of six 6 months from the date of purchase The warranty is strictly limited to the replacement or the repair of the UPI ST Interface or parts thereof showing a manufacturing defect according to the final judgment of UMS UMS shall never accept a warranty claim if the user has carried out repairs or modifications to the UPI ST Interface or if the defect results from assembly maintenance storage or use in a manner which is inconsistent with the indications and recommendations by UMS or from use for purposes other than those described in the User Manual abnormal use overloading or normal wear or if the original UMS identification label or serial number has been removed or if the warranty p2. 00 Handset Upon start up the UPC 100 Handset asks you to select the truck type on which you wish to perform your diagnostics and or parameterization Select the correct truck using the up down arrows and confirm by pressing the OK button Once you confirmed your selection the CAN communication is initialized The status is displayed in zone C see menu structure of the display After initialization the UPC 100 Handset will expect you to confirm that all safety precautions described in the truck manufacturer s instructions have been taken blocking up jacking up etc Press OK only if this is the case 5 Structure of the display Navigate the display by using the arrow keys 4 5 6 7 Select an item by pressing the OK key 3 Use the ESC key 2 to return to the previous screen 5 1 Diagnostics Zone D The diagnostics menu is used to read out the present value of a certain sensor actuator e g switch status motor current Values are read only they cannot be changed Highlight a value to refresh it This menu is divided in 3 submenu s Drive Hydraulic and Misc 5 2 Parameters zone G In this menu users can read out as well as manipulate parameters that influence the behaviour of the truck 2012 Universal Machine Solution Pte Ltd All Rights Reserved This user manual one or more parts of it may only be reproduced distributed or translated with explicit written and prior permission by Universal Machine Solutio
3. WWW UMS SQ User Manual UPI ST interface Used for Still industrial trucks Last updated in 01 2013 Date Description Rev nr 01 10 2012 Initial release A 09 01 2013 Minor update B 2012 Universal Machine Solution Pte Ltd All Rights Reserved This user manual one or more parts of it may only be reproduced distributed or translated with explicit written and prior permission by Universal Machine Solution User Manual UPI ST Interface Page 1 7 WWW UMS SQ Table of Contents To ii R0f6 8c 0 g eeeneeeem eee mere ee nee ee nee ence ee ere er eee a eer eee 3 SD AS aca sce cae a see tt es geese st ee tae ne ade E oct esd ete 3 t2 WINGS ce eesseeaseatetctiries nena ces E E E E rete tenes wean E 3 13 Contents andTirst Useisiin r eea tie latvia bea e e oate 3 2 OUPPOrEd tr CKS iciaeaie eee ee eee ee eee ee ene ee er ee ere ee 3 3 Locating the service connector ON the trUCK cceeeeeeeeeeeeceeeeeeeeeeeneeaaeeeeeeeeeeeesaaaaaaaeeeeeeeeeeseneaaaseeeeees 4 4 Starting up the handset erresires niner ekinen ee contseinnardaicsentsh EREA ENEE E KEA NEEE EATE ENE EEEE RERE 4 5 Structure of the display sas asa eeecezans Hes ecateteca dors ct eecies lt ctzacs eaegaly sate dack otaseeesuacttacs eaceass ese sack eeiachapassan atganiy 4 51 Diagnostics Zone asset tee ee ee eee 4 5 2 Parameters ZOMG G asriresneninenaso E ea EAE A E E A ea eta 4 5 2 1 Drive parameters sanckcicracenerecuterecenacereinrathe
4. eriod has lapsed The warranty excludes all costs for transportation 2012 Universal Machine Solution Pte Ltd All Rights Reserved This user manual one or more parts of it may only be reproduced distributed or translated with explicit written and prior permission by Universal Machine Solution User Manual UPI ST Interface Page 6 7 WWW UMS SQ Warranty claims are administered through Universal Machine Solution Pte Ltd Company registration number 201201400E Contact www ums sg 2012 Universal Machine Solution Pte Ltd All Rights Reserved This user manual one or more parts of it may only be reproduced distributed or translated with explicit written and prior permission by Universal Machine Solution User Manual UPI ST Interface Page 7 7
5. n User Manual UPI ST Interface Page 4 7 WWW UMS SQ Warning wrongful manipulation of the parameters can result in uncontrolled behaveiour of the truck possibly causing severe injury or death The parameter list depends on the selected truck 5 2 1 Drive parameters This submenu contains all parameters affecting the driving behaviour of the truck Amongst these are maximum drive speeds number of drive programs 5 2 2 Logic parameters In this submenu users can change parameters of the logic functions AND OR XOR 5 2 3 Indication parameters This list contains settings for lighting truck console display flashers 5 2 4 Misc parameters This submenu contains all other parameters 5 2 5 System parameters Users can perform following actions Change service hours make sure the truck is sufficiently serviced when changing these service hours Insufficient service can cause damage to the truck Reset error list clear all errors stored in the truck memory Reset device Restart the controllers of the truck Set service address if a certain parameter cannot be changed using the implemented parameter lists a user can set the corresponding service address to the correct value 5 2 6 Store load parameter sets Store all truck parameters on the UPI ST or restore a previously stored set to the truck 5 3 Errors zone H 5 3 1 Show error list View a list of the last maximum 8 errors that occurred on the truck By pressi
6. n and prior permission by Universal Machine Solution User Manual UPI ST Interface Page 2 7 WWW UMS SQ 1 Introduction 1 1 Use The UPI ST Interface and the UPC 100 Handset enable the user to amend the factory settings of certain Still industrial trucks The UPI ST Interface must be used together with the UPC 100 Handset Any other use is not authorized Remark Drawings and images in this UPI ST Interface manual may differ from your model 1 2 Warnings Amending factory settings of an industrial truck can cause material and physical injury Therefore the UPI ST Interface and the UPC 100 Handset must only be used by skilled trained and authorized staff The users of the UPI ST Interface must have access to the user manual at all times Read this UPI ST Interface manual carefully before connecting maintaining or using the UPI ST Interface Strictly follow the safety instructions in the truck manufacturer s maintenance manual prior to connecting the UPC 100 Handset and the UPI ST Interface to the truck Warning Failure to comply with the instructions and warnings in this manual could result in serious injury to the user or other persons in the vicinity of the truck 1 3 Contents and first use The package contains the UPI ST Interface the UPA ST RX cable and the UPA ST CAN cable 2 Supported trucks The UPI ST Interface fully or partially supports trucks of the types listed below Warning The UPI ST Interface does not fully suppor
7. ng OK the user can see detailed error information 5 3 2 Error information A list is available with all errors that can be recognised by the UPI ST Handset with respect to the selected truck Select the correct error number and press OK to view error information This list is truck dependent 5 4 Handset Zone 1 See UPC 100 Handset Manual 5 5 Information field Zone C Zone C displays the two most recent errors or warnings supported by the UPI ST Interface 6 Cleaning the UPI ST Interface Only use a damp cloth to clean the housing and the cable Do not use any solvents or liquid 2012 Universal Machine Solution Pte Ltd All Rights Reserved This user manual one or more parts of it may only be reproduced distributed or translated with explicit written and prior permission by Universal Machine Solution User Manual UPI ST Interface Page 5 7 WWW UMS SQ 7 Maintenance There are no user serviceable parts present in the UPI ST Interface Upon defect the unit must be returned to UMS for repair If the UPI ST Interface is damaged return it to UMS Any attempt to unscrew alter repair or interfere otherwise with the UPI ST Interface will invalidate any warranty 8 Storage The unit must be stored in a dry frost free room 9 Problem solving Problem Solution only see the handset icon in the main menu Make sure the cable towards the truck is connected to the interface The display shows can t locate the
8. ssthinereceiaaserereie meee eile etnetaee 5 522 Logicparamnetel S ennn eee ee a e eee eee eee 5 5 2 3 INDICATION parameters icocisnvccnetimnnbnmean deen EAEE EA REAREA EEDE EEEE EAEE KERERE 5 5 2 4 Misc DAN CISTS wanes eresecctocacenceteasnistenisnecsmrnianeratpntceteeiatsewieseostteumeemieederenemieetewionamietene 5 52 9 System palaMel S nsir iens ia enp Seats eee eee eee 5 5 2 6 Store load parameter sets eee ee ee eer eee eee ee ee eee 5 5 3 Errors Zone A scree cries exer cs telcos ee oameiendsac ae e a a eee 5 5 3 1 Show error ISten na REKE E AEREN ENE EE A EREKE TREA ENEE RER REER 5 5 32 Error informat M eseria aeea Eaa aae ae eS Ea SEEE daha ETEei maces 5 54 ene Serle rss ee ee ee eee 5 5 5 Infomation field ZOMG GC as csssecccbasesaiesipucsinee neenaka E naaa EN opaa AEN ETEN EREA EKAN E EEAS 5 6 Cleaning the UPI ST WGC Ciccctec etn ccetetends atte nedaanctaite wee eiancianten tue taanetaanneiereareeas malaenelermeas 5 Be MAA SN a eco eee aa ec assent eeecnieeee ee ci e 6 8 Storage riene eke nn nae EERE E EEE EEE 6 9 Probier Solinger a E E EE S aE EA E 6 10 Transporte a e a N a a e e e 6 11 Regulatory ONO ANG ce ce we te den i easements cine Seen stat ct rca tetera eee 6 12 CN AAI ct edearesceeagecbcrdnaesiaqcicetant a ac nee E a aoa ere Sheen at 6 2012 Universal Machine Solution Pte Ltd All Rights Reserved This user manual one or more parts of it may only be reproduced distributed or translated with explicit writte
9. t all truck configurations in particular less common configurations The UPI ST Interface is under constant scrutiny development and improvement and feedback of user experiences is extremely valuable In case of doubt or concern please contact UMS Name Serial R20 2008 2010 2013 2009 2011 2012 2014 2016 2017 2018 2020 2023 2019 2021 2024 2022 2037 2038 2039 2041 2044 2042 R60S20 6022 6023 6024 6025 6026 6027 6028 6029 6030 6031 6032 6042 6043 6044 6045 6046 6047 6048 6049 6050 6051 6052 6053 R70 7048 7049 7050 7052 7053 7054 7055 7056 7062 7063 7064 7065 7069 7070 7074 7075 7076 7077 7078 7079 7084 7085 7086 RX20 RX60 631 1 6313 6315 6210 6211 6212 6213 6214 6215 6216 621 7 6327 6328 6329 RX50 5051 5052 5053 5054 5055 RX70 7321 7322 7323 7324 7325 7326 7327 7328 2012 Universal Machine Solution Pte Ltd All Rights Reserved This user manual one or more parts of it may only be reproduced distributed or translated with explicit written and prior permission by Universal Machine Solution User Manual UPI ST Interface Page 3 7 WWW UMS SQ 3 Locating the service connector on the truck The service connector is usually located at the bottom of the truck console display when the driver is seated it is located at his left hand side 4 Starting up the handset Carefully read the installation instructions in the UPC 100 Handset User Manual before starting up the UPC 1
Download Pdf Manuals
Related Search