User`s Manual Digital Video/Audio Optical Extender
Contents
1. Step 4 Plug the 12V power adapter to the power jack of the receiver Ensure the red LED for Power and green LED for Optic are lit Re 7 SP Se Figure 3 Connection of power adapter to the receiver 1 3 Installation Step 5 Connect LC optical fiber between the transmitter and the receiver as shown in figure 4 1 of transmitter should be connected to 1 of receiver and 2 of transmitter should be connected to 2 of receiver by fibers _ N Ten N K HoA E P A a S gt A ae we li o Plin G be 7a Figure 4 Connection of optical fibers Note Both of single and multi mode fibers are applicable up to 500meters In the case of longer than 500meters you have to use single mode fibers Step 6 Plug the transmitter to the DVI receptacle of the DVI source such as PC and analog stereo audio SN Figure 5 Connection of the transmitter to the DVI source Note Be recommended NOT to use any intermediate cable or adapter between them to avoid undesirable performance degradation Step 7 Plug the receiver to the DVI receptacle of the display and speaker A A Audio Display Output Figure 6 Connection of the receiver to the display Step 8 Make the PC and the display power ON Ensure that status LED is lit Note You can replace any DVI cable into an M1 203D TR by following the Step1 to 7 while all powers of PC and display are ON 1 4 Installation Self EDID Pr2. 79 www opticis com For order support please contact your Distributor or Reseller For technical support check with the Opticis web site www opticis com or contact techsupp opticis com
3. LC fibers It gives benefits of all glass fiber transmission medium data security long distance extension up to 2km easy plug and play installation and no RFI EMI effects In addition a non trivial feature is that both of Single and Multimode optical fibers are applicable The EDID Extended Display Identification Data in a display can be read and restored by just plugging once transmitter to the display This Self EDID programming feature makes the installation of M1 203D TR more easy and flexile at any variable resolution display systems For your convenience UXGA EDID would have been done before shipment as a default Shipping Group o M1 203D TR Optical DVI Extension Module One 1 pair o DC power adapter Two 2 units o User s Manual o Option Product Duplex LC Patch Cord Single or Multi mode fiber T 7 Control Server or PC Audio Display Output Figure 1 Schematic Connection Diagram of Optical DVI Audio Extension Modules 1 1 Welcome Product Description System Requirements for Setup o Hardware requirements m You have to have a DVI graphic controller or card having a DVI port in your PC SUN or Mac systems It should support the maximum graphic resolution feature of displays to be connected m No special requirements for memory size CPU speed and chipsets if you ve already properly installed your DVI graphic controllers or cards o Software requirements m No special restrictions if you ve already prop
4. Manual Contents Manual Contents 1 0 Welcome Product Description 1 1 System Requirements for Setup 1 2 Installation 1 3 Self EDID Programming Procedure 1 5 Troubleshooting Maintenance Technical Support 1 6 Product Specifications 1 7 Warranty Information 1 8 Regulatory Statements 1 9 Digital Video Audio Pictorials Figure 1 Schematic Connection Diagram of Optical Extender Optical DVI Audio Extension Modules 1 1 Figure 2 Connection of power adapter to the User s Manual transmitter 1 3 Figure 3 Connection of power adapter to the For M1 203D TR ech 3 Figure 4 Connection of optical fibers 1 4 Figure 5 Connection of transmitter to DVI Audio source 1 4 Figure 6 Connection of receiver to the display speaker 1 4 Figure 7 Position of Self EDID button and EDID PRGN LED 1 5 1 0 Manual Contents Welcome Congratulations on your purchase of the M1 203D TR Digital Video Audio optical extender This manual contains information that will assist you in installing and operating the product Product Description M1 203D TR offers integrated extension of digital video and audio up to 2Km 6 600feet for DVI It maintains HD video signals up to WUXGA 1920x1200 at 60Hz refresh rate for PC It is compatible with full DDC2B It supports connecting a stereo analog audio in the transmitter and transmits to Receiver It is designed to multiplex and de multiplex the DVI video analog audio to be linked over 2
5. al or general product support contact your reseller For technical service contact Opticis by email techsupp opticis com or visit its website at www opticis com 1 6 Troubleshooting Maintenance Technical Support Product Specifications M1 203D TR Optical DVI Extension Modules O Compliance with DVI standard Supports DVI1 0 fully implemented by fiber optic communication and DDC2B by virtual DDC O Extension limit 2Km 6600feet for WUXGA 1920x1200 at 60 Hz refresh rate Fiber Type Extension Length at WUXGA Multi mode Fiber 500m Single mode Fiber 2000m O Graphic transmission bandwidth Supports up to WUXGA at 60Hz or 1 65Gbps bandwidth per graphic channel O Fiber optic connection The transmitter and receiver modules of M1 203D TR have two LC receptacles so as to be connected with one LC duplex single or multi mode fibers having 9 8 125um or 62 5 50 125um core DDC connection Virtual DDC by Auto EDID programming Mechanical specifications of transmitter and receiver modules m Dimensions 108mm 25mm 115mm W H D O Environmental Specifications m Operating temperature 0 C to 50 C m Storage temperature 10 C to 85 C m Humidity 5 to 85 AC DC Power Adapter O Power Input AC 100 240V 50 60Hz O Power Output 12 V 3A SMPS DC power Adapter O Cord DC Jack Core is 5 V and outer is GND 1 7 Product Specifications Warranty Information 1 One Year Warranty Opticis warrants this optical DVI ex
6. er devices which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving device e Increase the separation between the equipment e Connect the equipment into an outlet on a circuit different from that to which the other device s are connected e Consult the manufacturer or field service technician for help e Type of protection against electric shock Class equipment e Degree of protection against electric shock Not classified no applied parts e Classification according to the degree of protection against ingress of water as detailed in the current edition of IEC 529 IPX0 ordinary equipment e This equipment is not suitable for use in the presence of flammable anesthetics or oxygen e Mode of operation continuous operation Certification of Eye Safety This laser product is inside implemented by using 1300 1550nm optical module manufactured by Opticis Co Ltd which are all certified by IEC EN60825 1 referred in Accession Number 07 1334 0217 as classified in Laser Class1 1 9 Regulatory Statements 2009 Opticis Co Ltd All Rights Reserved Revision 1 0 Nov 26 2009 Opticis Locations Headquarters Opticis Co Ltd 304 Byucksan Technopia 434 6 Sangdaewon Dong Chungwon ku Sungnam City Kyungki Do 462 716 South Korea Tel 82 31 737 8033 8 Fax 82 31 737 80
7. erly installed your DVI graphic controller in your OS o AC DC Power Adapter Technical Advisory The transmitter Tx module of M1 203D TR is designed for power protection circuit in order to prevent electrical shock or damage from power supply through the external DC power adapter Both the transmitter Tx and receiver Rx module should be supplied by an AC DC power adapter Analog Audio Technical Advisory Independent analog audio input to transmitter Tx is disable to transmit without DVI graphic input Analog audio input or output is fully compatible with M1 203D TR However digital audio does not support at all 1 2 System Requirements for Setup Installation Important Please use the installation procedure below Improper or no operation may result if the start up sequence is not correctly followed Step 1 Carefully unpack the contents of the shipping group Step 2 Plug the 12V power adapter to the power jack of the transmitter Ensure the red LED for Power and green LED for Optic are lit Figure 2 Connection of power adapter to the transmitter Note You Must connect the power adapter to the transmitter even if the graphic source provides enough power to operate the transmitter Please refer to AC DC Power Adapter Technical Advisory on page 1 2 Step 3 Please check if the maximum resolution of the display is UXGA 1600x1200 Otherwise follow the instructions for Self EDID Programming Procedure on page 1 5
8. lf EDID Programming Procedure Troubleshooting The display displays only black screen Ensure that all plugs and jacks used by external power supplies both Opticis and others are firmly connected Ensure the red for Power and green for Optic LED ON Ensure that the DVI ports are firmly plugged in to the PC and display Ensure that the transmitter and receiver modules plugged correctly to the PC and display respectively Check if the PC and display are powered on and properly booted Reset the system by de plugging and re plugging the transmitter DVI port or receiver DVI port or by de plugging and re plugging the power cord plugs of transmitter and receiver modules Re boot up the system while connecting the optical DVI extension module Screen is distorted or displays noises Check if the graphic resolution is properly set Go to the display properties of Windows and tap the settings Ensure that the resolution sets less than WUXGA 1920x1200 at 60Hz refresh ratio Reset the system Disconnect and reconnect the optical DVI cables or 12V power adapters Maintenance No special maintenance is required for the optical DVI module and power adapters Ensure that the DVI modules and power adapters are stored or used in a benign environment free from liquid or dirt contamination There are no user serviceable parts Refer all service and repair issues to Opticis Technical Support and Service For commerci
9. ogramming Procedure The graphic source equipment generally requires communication of display information EDID Display information EDID contains resolution and timing information for your display M1 203D TR supports Self EDID programming Self EDID programming means that the EDID from the display is stored in the transmitter You should use Self EDID programming feature if the resolution of the display is not UXGA 1600x1200 Follow these steps to record the EDID of the display into the transmitter unit Note1 If you know that EDID is not required by the source Self EDID programming is not necessary Note2 The default EDID in factory ship out is programmed in the VESA standard of UXGA 1600x1200 60Hz Step 1 Power on the display Step 2 Plug the 12V DC power adapter into the transmitter Step 3 Push and stay the Self EDID button of the transmitter with a pin until EDID PRGN LED is blinking once After blinking of Self EDID LED 4 times LED will be automatically turned off Self EDID button EDID PRGN LED Figure 7 Position of self EDID button and EDID PRGN LED Step 4 Connect the transmitter to the display while turned on not to the PC The LED on the transmitter will begin to blink rapidly Blinking indicates reading the EDID LED will be turned OFF after blinking about 19 sec The monitor EDID has been recorded Step 5 Disconnect the transmitter from the display Then LEDs are lit again 1 5 Se
10. rical amp Electronic Equipment Applicable in the European Union and other European countries with separate systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative Sa consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 1 8 Warranty Information UL IEC Statement This equipment has been tested and found to comply with the limits for medical devices in IEC 60601 1 1994 These limits are designed to provide reasonable protection against harmful interference in a typical medical installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to other devices in the vicinity However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to oth
11. tension module to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers If a product does not work as warranted during the applicable warranty period Opticis shall at its option and expense repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agents causes other than from ordinary use or failure to properly use the product in the application for which said product is intended Dispose of Old Elect
Download Pdf Manuals
Related Search