User`s Manual
Contents
1. s Manual 11 ADVASPLSYS is loaded from the CONFIG SYS file and automatically installed by either the DOS or Windows based installation programs To install it manually simply add the line device advaspi sys To minimize possible confusion it is a good idea to create an ADVSCSI directory to hold all of the 3092 software files In this case the directory path would be device advscsi advaspi sys The automatic install programs use this method Command line options separated by forward slashes and containing no spaces can be added on the same line For example device advaspi sys p v You can also load ADVASPL SYS into high memory if you install the appropriate memory manager before loading ADVASPLSYS Command Line Options 12 Several command line options can be used with ADVASPLSYS Most installations will not require any of these but there are circumstances for which one or more may be necessary The command lines are as follows L By default logical units LUNs are not supported by ADVASPI SYS To enable LUN support specify the L option at the command line P With the P option ADVASPI will pause and continue when you press any key V A verbose display will be printed during initialization showing adapter I O ports IRQs and other miscellaneous information NE and NP The NE and NP options will disable searching the PCI bus respectively for 3092 SCSI cards Because the host adapters w2. Manual DOS Windows 3 1 Driver Installation DOS Driver Installation 1 Shut down DOS and switch your computer power off 2 Plug in the host adapter card and turn your computer power on 3 Insert the installation diskette into the floppy drive 4 AttheC gt prompt type A and press Enter 5 Atthe A gt prompt type install and press Enter 6 A screen message appears This program will install the DOS Drivers Press Enter here and on the next two screens to confirm that driver files will be copied to the C drive 7 A screen message appears Do you want to include Disk Driver in your CONFIG SYS file Press Enter to include the Disk Driver 8 A screen message appears Do you want to include CD ROM Driver in your CONFIG SYS file Press Enter to include the CD ROM Driver or select No if you don t have CD ROM 9 A screen message appears Is it OK to add the following lines to the ends of your CONFIG SYS and AUTOEXEC BAT files Press Enter to add the lines indicated 10 Eject the disk from the floppy drive 11 If you want the driver installation to take effect now reboot by pressing Ctrl Alt Delete Otherwise press any key to continue 12 Driver installation is now complete and CONFIG SYS and AUTOEXEC BAT are successfully loaded ADVASPLSYS is the 3092 Universal ASPI Manager for DOS and Windows It is designed to support 3092 host adapters using MS DOS 4 01 or later version 3092S SL E User
3. and product description Type and version number of Operating System you are using E g MS Windows95 Software driver product type and version number Motherboard BIOS version Location of purchase The README TXT File The README TXT file on the 3092S SL 3191E DRIVER DISK 1 contains important updated information and corrections to this User s Manual README is a standard ASCII text file that may be read with any word processor or text editor To view the README file from the MS DOS prompt Type the following command from the MS DOS prompt C gt type readme txt more This will permit you to page down the file one screen at a time to read the file Table of Contents HOST ADAPTER SPECIFICATIONS cccssssssssssssssssessesessssesesssessssssessssssesesscsssessseesees L HARDWARE FEATURES svssiesissiesceccescs sevice devccesetssecdvesuceudeves sis siesia desl sivssusteds ise dutincdatvsccecessisstesies 1 PCEB s Interfacing o EE beat dad E E AREE EE ie ndhdnaceaaias SCSI Bus Interface TECHNICAL SPECIFICATIONS eiececseessicssedatecesetescescesecoussetvvis sie slestdesdesevsuedvese EEE a 2 ENVIRONMENTAL SPECIFICATIONS cscsscssessessesscesceseescescscecesseesessesessecaecescssesaesaescaecaecaesaeeaees 2 HARDWARE INSTALLATION csssssscsssssosesssssosessssssessrsseserssssesersrsnesersssseserersseserersseserss 3 3092S SL 3191E HOST ADAPTER KIT CONTENTS cccscsscssessessesscesseseeceseeseeceeceese
4. copies the following contents to it 14 3092 SCSI ASPI Manager 3092 SCSI CD ROM driver and utility 3092 SCSI Hard Drive Removable Media Manager 3092 SCSI SCSI Info Utility Text Files describing the above software This install program Type INSTALL at the root directory on your installation disk You will be asked to choose the destination boot drive which is typically the C drive A directory called ADVSCSI will be created on the chosen drive and the ADVANCD software will be copied to it You will be asked if it is OK to automatically modify and back up your AUTOEXEC BAT and CONFIG SYS files Unless you have a specific reason not to type Y to go ahead and modify these files If you have already installed the ADVANCD software type N If you answered no N you will have to add the CD ROM driver to the AUTOEXEC BAT and CONFIG SYS files manually If you answered yes Y the installation program will install the CD ROM driver once the AUTOEXEC BAT and CONFIG SYS files are modified and saved Reboot for the changes to take effect 3092S SL E User s Manual From the Windows 3 1 Environment You can use the Setup Program to install and configure the CD ROM driver 1 2 Start Windows 3 1 and insert the installation diskette into drive A Select File from the Program Manager and then select Run from the File drop down menu When the Run submenu appears type a dos setup in the command line Click OK to c
5. e a e a a a a a i aaa BASINS 21 TIRA NAS D AR O TESE E EENE E E A EAT EE 21 Installing the Windows NT Drivef sssssssssssssssssessseteseeeseseseneseneseneneneseneseaeseneneaeneneneneees 21 PRODUCT WARRANTY senusien nssr E ee 22 3092S SL E User s Manual i Host Adapter Specifications This chapter describes the 3092S SL 3191E PCI to Ultra SCSI host adapter card in detail The 3092S SL 3191E card is a high performance PCI bus master host adapter that provides a highly integrated solution for attaching SCSI devices to your PC Hardware Features PCI Bus Interface Fully compliant with the PCI Local Bus Specification Revision 2 32 bit Bus Master DMA allows for a data transfer rate of up to 133 MB sec across the PCI Bus 5 Volt only PCI board SCSI Bus Interface 8 bit Fast SCSI 10 MB sec synchronous data transfer rate across the SCSI Bus Single ended SCSI interface SCSI 2 and SCSI 1 devices peripheral device connectivity Tagged queuing supported for SCSI Scatter gather function supported Each host adapter card supports up to seven peripheral devices 3092S SL E User s Manual 1 Technical Specifications Computer Bus PCI Bus Interface Protocol Bus Master DMA Device Protocol SCSI Device Support Up to seven SCSI devices Bus Width SCSI 8 bit and PCI 32 bit PCI Host Bus Data Transfer Rate 5 MB sec asynchronous burst on the SCSI bus 10 MB sec synchronous burst on the Fast SCSI bus Electrical Terminatio
6. proceeding further If you need help installing Windows NT please refer to the Microsoft Windows manual before proceeding 1 Turn on host system and boot into Windows NT Operating System 2 Insert the 3092 SCSI Host Adapter Driver Disk 1 into your floppy drive 3 Use your installed mouse or the appropriate key strokes to select RUN from the Windows PROGRAM MANAGER Execute the program e Type A WINNT SETUP lt ENTER gt A series of screens will guide you through the installation of the ASPI for Windows device drivers 3092S SL E User s Manual 21 Product Warranty We warrant to the original purchaser that this product shall be free from defects in material and workmanship for a period of 1 years from the date of purchase Should this product in the judgment of us prove to be defective We will at its option repair or replace the product once it has been returned to us free of charge Any replaced parts a products become the property of us You may obtain warranty service by first getting authorization from us then returning this product with proof of delivery date shipping charges prepaid to us This warranty does not apply to the software component of the product nor to any product which has been subjected to misuse accident abuse or use in a manner inconsistent with normal host adapter operations The original purchaser must be registered with us by mailing the Product Registration Card to qualify for warranty coverage This r
7. 3092S SL E PCl to SCSI Host Adapter User s Manual Revision 1 0E C Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Copyright Copyright 1999 We make no warranty of any kind in regard to this material including but not limited to the implied warranties of merchantability and fitness for a particular purpose We are not liable for any errors contained herein or incidental or consequential damages in connection with furnishing performance or use of this material This document and the information contained herein are the property of us No part of this document may be reproduced transmitted stored in a retrieval system transcribed or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the express written consent and authorization Trademarks MS DOS WINDOWS WINDOWS for Workgroups Windows 95 Windows 98 and WINDOWS NT are trademarks or registered trademarks of Microsoft Corporation NetWare is a registered trademark of Novell Inc Intel i386 i486 1486DX2 and Pentium are trademarks of Intel Corporation Other manufacturers product names that appear in this manual are for identification purposes only and are acknowledged to be trademarks or registered trademarks of their respective companies The following information is needed to assist in problem resolution Model type serial number
8. 92 PCI SCSI Bus Controller Properties window select the DRIVER tab then select CHANGE DRIVER e In the SELECT HARDWARE TYPE window select SCSI CONTROLLERS e Inthe SELECT DEVICE window select HAVE DISK 4 In the INSTALL FROM DISK window that is displayed enter the 3092 Driver path name e Insert 3092 SCSI Host Adapter Driver Disk 1 into drive A e Type A WIN95 select OK 5 Select AdvanSys PCI SCSI Host Adapter select OK then OK again to install the ASC MPD driver onto your hard disk drive 6 This completes loading the Host Adapter Driver follow the on screen directions to complete the Windows 95 installation Exit and reboot the system to activate the device driver 3092S SL E User s Manual 17 7 Itis highly recommended that you verify your Windows 95 device driver has been properly installed by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER listing and e Select AdvanSys PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed Adding the Device Driver to an existing Windows 95 system These instructions will guide you through the installation of the 3092 host ad
9. OLLER from within the DEVICE MANAGER listing and e Select AdvanSys PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed Updating the device driver to an existing Windows 95 system 1 Once a Windows 95 session is established use your installed mouse or the appropriate key strokes to select MY COMPUTER from the Main Desktop Execute the following steps e Select CONTROL PANEL from within the MY COMPUTER group e Select SYSTEM from within the CONTROL PANEL group 2 Select the DEVICE MANAGER tab from within the SYSTEM group e Select the SCSI CONTROLLERS category from within the DEVICE MANAGER listing e Select the AdvanSys PCI SCSI Host Adapter sub category from within the SCSI CONTROLLERS listing 3 In the AdvanSys PCI SCSI Host Adapter PROPERTIES window select the DRIVER tab then select CHANGE DRIVER 4 In the SELECT DEVICE window select HAVE DISK 5 Inthe INSTALL FROM DISK window that is displayed enter the 3092 Driver path name 3092S SL E User s Manual 19 20 e Insert the 3092 SCSI Host Adapter Driver Disk 1 into drive A e Type A WIN95 select OK Select AdvanSys PCI SCSI Host Adapter select OK to install the 3092 MPD driver onto your hard disk drive This completes updating the Host Adapter Driver Follow the on screen directions to restart you
10. apter to an existing Windows 95 system Windows 95 will automatically detect the presence of new hardware in Plug and Play compliant systems It is important that the 3092 hardware has been properly installed before proceeding further 1 Microsoft Windows 95 will detect the presence of new hardware upon boot up and will display a dialog window titled NEW HARDWARE FOUND and PCI SCSI BUS CONTROLLERS will be highlighted e Select DRIVER FROM DISK PROVIDED BY HARDWARE MANUFACTURER then OR e Select SCSI CONTROLLER from the list of available devices then select HAVE DISK 2 Inthe INSTALL FROM DISK window that is displayed enter the 3092 Driver path name e Insert 3092 SCSI Host Adapter Driver Disk 1 into drive A e Type A WIN95 select OK e Windows 95 will ask you the pathname again e Type A WIN95 and select OK 18 3092S SL E User s Manual 3 Windows 95 will now transfer the ASC MPD driver on to your hard disk drive 4 This completes loading the Host Adapter Driver follow the on screen directions to complete the Windows 95 installation Exit and reboot the system to activate the device driver 5 It is highly recommended that you verify your Windows 95 device driver has been properly installed by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTR
11. asons Ifyou are attaching fewer than five SCSI devices to the host adapter the maximum cumulative cable length for FAST SCSI 10 MB sec SCSI data transfer is 6 0 meters If you plan to attach from five to eight devices the maximum cumulative length for cabling is 1 5 meters Tools Required You will need a Phillips screw driver to open the computer chassis remove the blank slot cover on the motherboard and to secure the adapter once it s installed 4 3092S SL E User s Manual 3092 Host Adapter Card Overview The 3092S has one internal 50 pin connector and one 50 pin High density external connector Figures 1 2 and 3 identify the major components of the 3092 PCI SCSI host adapter respectively Table 1 and 2 describe each component You may find it helpful to refer to these illustrations while installing the host adapter and attaching the cables Figure 1 3092S Board Layout 50 pin Internal SCSI Connector 50 pin External high density SCSI Connector Table 1 3092S Component Description 3092S SL E User s Manual 5 qd Figure 2 3092SL Board Layout Figure 3 3092E Board Layout aia EST Connector 2 3 ON Auto detect and termination for the external device Assume external device always on For IOMEGA Zip device connector only Table 2 3092SL E Component Description 6 3092S SL E User s Manual Installing the Host Adapter Card 1 2 5 Shut down your system and turn off the
12. computer and activate the new driver It is highly recommended that you verify your Windows 95 device driver has been properly installed by selecting MY COMPUTER from the desktop Then select CONTROL PANEL e Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER from within the SYSTEM group e Select SCSI CONTROLLER from within the DEVICE MANAGER listing and e Select AdvanSys PCI SCSI Host Adapter from within the SCSI CONTROLLER listing If This device is working properly is displayed on your screen the driver has been correctly installed 3092S SL E User s Manual Microsoft Windows NT Driver Installation Overview The 3092 PCI SCSI host adapter will support Windows NT v3 5x 4 0 with the addition of a software driver A software driver allows the host comp uter the ability to transfer data over the SCSI bus The device driver for Windows NT is copied from the 3092 driver installation diskette to your hard drive where it is loaded onto the computing system during installation Installation The 3092 driver developed for Windows NT will be installed on the hard drive used for system initialization The driver is loaded during the system boot routine and will remain resident on the drive Installing the Windows NT Driver The ASPI for Windows NT driver is found on the 3092 SCSI Host Adapter Driver Disk 1 It is important that the SCSI bus hardware and Operating System are installed correctly before
13. emedy is your exclusive remedy for breach of this warranty WE DISCLAIM ALL OTHER WARRANTIES EITHER EXPRESSED OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WE SHALL BE LIMITED TO THE WARRANTY PERIOD SPECIFIED ABOVE ALL OTHER WARRANTIES ARE EXCLUDED OUR TOTAL LIABILITY HEREUNDER SHALL NOT EXCEED THE PRICE PAID FOR THE PRODUCT PURCHASED IN NO EVENT SHALL WE BE LIABLE FOR ANY INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCT EVEN IF WE HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 22 3092S SL E User s Manual
14. mination 8 3092S SL E User s Manual SCSI ID Assignment Each and every SCSI peripheral device connecting to the same 3092 host adapter including the host adapter itself must be assigned its own unique SCSI ID SCSI IDs is numbered from 0 to 7 The default setting for the 3092 host adapter is SCSI ID 7 6 Figure 6 shows how to attach the internal SCSI cable to the host adapter card Connect one end of the internal 50 pin flat SCSI ribbon cable to connector J1 of the 3092 S SL host adapter card and the other end to any internal device Be sure to connect the colored edge of the ribbon cable to the side of J1 marked with an arrow pin 1 Make certain that the internal SCSI devices are connected with the colored edge of the cable to pin 1 of the device Cel Fa btn Coat In ad Oe Conn ido Figure 6 Connecting the 50 pin internal flat ribbon cable Note 3092E does not have internal SCSI connector 3092S SL E User s Manual 9 7 Installation of external SCSI cables can be performed after the cover has been closed The cable is limited in length to a total of six meters including any internal cabling The external cable can be daisy chained to include up to seven devices with the 3092 in combination with internal devices The external cable is designed to be inserted only one way requiring termination at the end peripheral device on the bus see figure 7 Figure 7 External cable connection 10 3092S SL E User s
15. ns Single ended Environmental Specifications Operating Temperature 0 C to 55 C Storage Temperature 40 C to 75 C Relative Humidity 10 to 95 non condensing FCC Certification 47 CFR Part 15 Subpart B Class B Digital Device Compliance to ANSI C63 4 1992 CE Compliance EN 50081 1 1992 Emissions EN 50082 1 1992 Immunity Compliance in accordance with CISPR 22B 1985 IEC 1000 4 2 1995 IEC 1000 4 3 1995 and IEC 1000 4 4 1995 2 3092S SL E User s Manual Hardware Installation You don t need to understand the highly technical PC jargon to install your high performance host adapter The next sections will walk you through the tasks of installing the host adapter and I O devices This chapter will show you how to customize the host adapter setup 3092 Host Adapter Kit Contents Before you install and configure the 3092 host adapter make sure that your package includes all of the following items 3092 PCI to SCSI host adapter card User manual Hardware Requirements For the PC AnIBM PC 486 or higher or compatible One or more SCSI peripheral devices up to a total of 7 per adapter card Atleast 640 KB of RAM Atleast 2 MB of free disk space for a basic installation SCSI external cable for external devices 3092S SL E User s Manual 3 Cable Considerations Please use a SCSI cable to attach SCSI peripherals to your 3092 PCI SCSI Host Adapter Card A SCSI cable is required for the following re
16. on t be controlled by ASPI they will not be available for use by other drivers or applications 3092S SL E User s Manual Installing the Windows 3 1 Driver 1 2 3 10 11 Shut down Windows 3 1 and turn OFF your computer Plug in the 3092 host adapter card and turn your computer ON At the C gt prompt type win and press Enter Insert the installation diskette into your floppy drive Double click on the File Manager and select Run from the File menu At the command line type in A DOS SETUP and click OK Now that you have successfully completed setup click OK to exit We recommend that you select Automatic Installation and follow the instructions provided on the screen A screen message appears Is it OK to reboot your computer now Click on YES Remove the disk from the floppy drive and click on OK Installation is complete Press any key to continue 3092S SL E User s Manual 13 Installing the ASPI and CD ROM Driver The 3092 SCSI CD ROM driver can be installed from DOS or from Windows 3 1 environments Follow the instructions below for your installed operating system From the DOS Environment This installer program quickly installs support for a SCSI CD ROM drive It is intended for those who want to get their CD ROM up and running without going through the entire Windows based installation of 3092 SCSI software and utilities The installer creates an ADVSCSI directory on the C or D drive and
17. ontinue The setup program will go though two phases to install and configure the CD ROM When prompted remove the diskette and restart your computer When the Setup program displays the message installation is complete click OK Now you can use your CD ROM 3092S SL E User s Manual 15 Microsoft Windows 95 Driver Installation Overview The 3092 PCI SCSI host adapter will support Microsoft Windows 95 with the addition of a software driver The installation procedure described here requires some experience in Windows 95 system setup and administration The device driver is transferred from the 3092 SCSI Host Adapter Driver Disk 1 to the hard drive where it is automatically initialized during the system boot routine The following files are used for installation and will be found on the 3092 SCSI Host Adapter Driver Disk 1 ASC MPD 3092 SCSI Host Adapter Windows 95 miniport driver ADVANSYS INF Windows 95 installation information file Installation The 3092 driver developed for Windows 95 is loaded during the system boot routine and will remain resident on the drive This is accomplished by following one of the three installation procedures listed e New Windows 95 installation e Adding the device driver to an existing Windows 95 system e Updating the device driver to an existing Windows 95 system The procedures described to make changes to the system have distinct differences It is strongly suggested that the selected proced
18. power for your PC Open your computer s chassis Touch the metal case of your PC to discharge static electricity Find an available PCI Bus slot and plug in the 3092 host adapter card Make sure that the card is seated properly and firmly in the slot Secure the card by tightening the mounting screw Figure 4 shows a properly seated 3092 host adapter card Figure 4 Inserting the SCSI Adapter into a PCI slot 3092S SL E User s Manual 7 SCSI Device Installation Install any internal and external SCSI peripheral devices according to the manufacturers installation instructions You can install a maximum of seven SCSI peripheral devices per 3092 host adapter So that signals can be transmitted properly across the SCSI bus the devices at both ends of the bus must be properly terminated The 3092 host adapter has automatic termination control for the host adapter end of the bus cable however you must ensure that the terminator at the other end the last peripheral device only of the bus cable is enabled Most devices use resistor networks as terminators To enable termination leave the resistor networks installed in their respective SIP Single In Line Package connectors To disable termination remove these resistor networks Active terminators generally have a jumper or switch that controls the enable disable feature Refer to the SCSI device s installation manual for more details Figure 5 Examples of SCSI bus ter
19. sseneesecnscnsens 3 H rdware Requirements ssivesisisssinivccivissvanasajeiny sos a E i E a ORAE 3 Cable Considerations src ai wisi a AEE A E E EEE Hadas 3092S SL 3191E HOST ADAPTER CARD OVERVIEW INSTALLING THE HOST ADAPTER CARD Q csccsccsssssescesssccseccesseesessesessecssceecssesaesaecaecaesaeeaeeaees SCST Device Installation esiin iro kan AEE AE E SCSI TD ASSIONMENK oaeee aa R e aE EE EE E a E EAN DOS WINDOWS 3 1 DRIV ER INSTALLATION ossessessosssossocsossossseesssosoosooscossocsossssesse 11 DOS DRIVER INSTALLATION ccccccscsscssssscssecsecsecseesceseeseesessecseceasesesecseeseeceeseseeseeascaecascsaesaens Command LINE Options a nesen a ara ea EE bis ses NEE V INSTALLING THE WINDOWS 3 1 DRIVER cccccsceseseeeees INSTALLING THEASPI AND CD ROM DRIVER From the DOS EnvirOnment cccscsscssssssssssssssssssssssscscesesscscesesecsseseseascesesecsoeaesecseeseseasees 14 From the Windows 3 1 EnvirOnment c cccccsssssesssssereseseveeeeseseseseseseneseneseneneneneaeneneneaeaes 15 MICROSOFT WINDOWS 95 DRIVER INSTALLATION ssssssseseessessooscoscossossosessecse 16 COVER DTA I D AAEE A E A AEN MNSTA ATON a a E E T E Bea Ba BOS E T a R EO New Windows 95 installation Adding the Device Driver to an existing Windows 95 SyYSt mM ssssssssesreeeee 18 Updating the device driver to an existing Windows 95 SyStemM ssssssssesseeseeee 19 MICROSOFT WINDOWS NT DRIVER INSTALLATION ssseseeseessossooscossossosssecsse 21 OVERVIEW carnoet a aa a
20. ure be read and understood before proceeding with the system configuration changes Please read the instructions carefully New Windows 95 installation These instructions will guide you through the installation of the 3092 host adapter driver while installing Windows 95 Windows 95 will be installed from either a CD ROM or floppy diskettes It is important that the hardware and DOS 4 01 or higher have been installed successfully before proceeding further If installing from a SCSI CD ROM drive it is important that the 3092 ASPI driver and CD ROM driver be installed before proceeding further 1 Access the Windows 95 CD ROM either fromthe DOS prompt or from Microsoft Windows 3 x File Manager Execute the SETUP EXE program and follow the instructions on your screen If you are installing from floppy diskette insert the 16 3092S SL E User s Manual Windows 95 Setup Disk 1 in your floppy disk drive and boot your system 2 Once a Windows 95 session is established use your installed mouse or the appropriate key strokes to select MY COMPUTER from the MAIN DESKTOP Execute the following steps e Select CONTROL PANEL from within the MY COMPUTER group 3 Select SYSTEM from within the CONTROL PANEL group e Select DEVICE MANAGER tab from within the SYSTEM group e Select the OTHER DEVICES category from within the DEVICE MANAGER listing e Select the PCESCSI Bus Controller sub category from within the OTHER DEVICES listing e In the 30
Download Pdf Manuals
Related Search