E•POWER BREAKDOWN SOLUTION MANUAL
Contents
1. xny Pubs Jaynes OND Jeune 5 yndyng 41005 samog xny jasey4 Ajddns xny Hd 1 4odyng 23213 1 3 3 42 005 843 118 3 42 005 91923 118 12 1 3 110 jhduy eJay 44 jndyjng jndyng zeyd 9 Ped INDAY T Gavi 23 13 Hdt d4M0d4 Wl 18049 4 97 JaSt pndyng 4284097 3 7197H 128 4007 lqeu 118783 ATWO SUE JURY 1 PSUR 5 Jub 5 dyaiejsueaj ased 5 UII H H 442214 Ayddns jnduy jesynay Mddes ynduy seyd usua ndu asya Y aseyd 5 jessy 1 9 1 91 pepu atay min TH SmiNet omu GRR iiiam NOLL WOINIWAWOD 587542. Eo POWER BREAKDOWN SOLUTI ON MANUAL COPYRIGHT PLUS s r l Via Braccesca 80 48100 RAVENNA ITALY ALL RIGHTS RESERVED Plus s r l Div marine Via Braccesca 80 48100 Ravenna ITALY tel 0544 270335 fax 0544 271498 Printed in Italy June 2009 E POWER PROBLEM SOLUTIONS Problem found Does not supply water Check that the display indicates a residual credit or is indicating ON Subscribed User ON OOOOOOO 10 00 0000000 Prepaid User Check that the tap symbol is present in the position of the asterisk This may be shown in alternation with the electrical plug symbol If this is not present close the facility and reopen it through the transponder taking care to select the water supply Does not supply electricity Check that the display indicates a residual credit or is indicating ON Subscribed user ON QOOOOOO Prepaid user 10 00 0000000 Check that the electrical plug symbol is present in the position of the asterisk This may be shown in alternation with the tap symbol If this is not present close the facility and reopen it through the transponder taking care to select the electricity supply Invalid system code If when bringing the transponder close the message is Invalid Plant Check That the key is valid and if so reset the facility with the reset transponder and try again Transaction not compl
3. 35 E POWER USER MANUAL START UP Insert the plug Bring the transponder close to the appropriate sensor placed above the socket to switch on Leave the transponder at the reading distance 1 cm and await loading Options Maintaining the transponder at the reading distance after start up will start the supply options only water only electricity and water electricity Remove the transponder during supply of the desired option SWITCHING OFF Bring the transponder close and complete the reading in order to shut down During shut down the remaining amount is shown on the transponder If the transponder is moved too far away during the start up and shut down procedures a general error message will be shown for example on tl off t2 In order to correct the error it is sufficient to correctly repeat the start up or shut down procedure TOPPING UP To top up the credit available on the socket switch off the system and switch it back on again within 10 seconds so as not to have even momentary loss of energy WARNING the cable must be suitable for the electrical current being distributed and must be no longer than 20 metres in length WARNI NG if the water and electricity warning light flashes this means that the anti theft protection has been activated to unblock switch off and repeat the start up procedure Yl iua FL 18422153 ONS 484103 Jape M
4. eted If the display shows one of the following messages OFF OFF T2 OFF T3 ON T2 T3 this means that the transaction has not been completed correctly Bring the key close once more and await the completion of the transaction Facility engaged If the following message is shown on activating the facility No free Hook up Check that the facility is actually available for use to free it from the current user utilize the transponder or the reset key Invalid transponder If the following message is shown on activating the facility Tag not valid Check that the key has actually been made for the facility intended to be activated Anti theft intervention if there is no supply of water and electricity and the display message is ON OOOOOOO 10 00 OOOOOOO Note that to the left of the line of squares there is either a flashing symbol or no symbol at all Close the facility and reopen it Intervention of the maximum absorption protection If the following message is shown on the display ON 10 00 I Max I Max Close the facility and reactivate it through the transponder If absorption is too high after a definable time interval default 5 min the supply will be stopped at the socket Display off Check magnetothermal protection of the facility For all other abnormalities it is advisable to call techncal assistance on 39 0544 2703
Download Pdf Manuals
Related Search