RGB 580xi User`s Manual
Contents
1. FE WUD FE DE EN This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The Class A limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense VIe This unit was tested with shielded cables on the peripheral devices Shielded cables must be used with the unit to ensure compliance with FCC emissions limits Table of Contents Chapter One Introduction 1 1 About the RGB 580 1 2 WR 1 2 Chapter Two Installation and 56 2 1 Installation 2 2 Under furniture mounting2. 2 3 Application 2 4 Front Panel Features and Cabling 2 6 Rear Panel Features and Cabling 2 9 Front Panel Adiustments ess 2 10 Mounting the Optional AAP 2 11 AAP Device 2 12 Cabling the AAP Device Rear Connectors 2 13 Cable Cubby AAP Device Features 2 15 Cabling the Cable Cubby AAP Devices 2 16 Troubleshooting esses 2 17 If the image does not appear or there is 2 18 If the image does not appear correctly 2 18 Chapter Three Remote Control 3 1 RS 232 Programmer s Guide 3 2 Host to interface communications sss 3 2 Interface initiated messages 3 2 Error TOSDOISBS 3 3 Using the command response 3 3 Windows Based Program Control 3 5 Installing the software 3 5 Using the software 3 5 Contact Closure Remote Control 3 6 Appendix A e Reference A 1 SPECIFICATIONS A 2 Included Parts A 6 Optio
3. The interface outputs serration pulses in the vertical sync interval Off The interface does not output serration pulses 3 SOG sync on green On The interface outputs sync on green Off The interface outputs separate horizontal and vertical sync on the H and V connectors for RGBHV 4 V Sync Width vertical sync pulse width For some digital display devices if no picture appears the picture cuts in and out or the picture is scrambled try adjusting the output vertical sync pulse width or switching from ADSP to DDSP On The vertical sync pulse is narrow Off The vertical sync pulse is wide 5 Neg Sync This switch controls sync polarity Both the horizontal and the vertical sync signals are forced to negative polarity on output Off Output sync polarity follows is the same as input polarity 6 Comp Sync This switch controls composite sync output On The interface outputs combined horizontal and vertical sync for RGBS Off The interface outputs RGBHV or RGsB video 2 8 RGB 580xi Installation and Setup Rear Panel Features and Cabling 100 240 0 5A MAX 6 OUTPUTS O Ox AUDIO RS 232 50 50 Hz IT PE RGB 580xi rear panel 1 AC power connector Connect a standard AC power cord here for power input 100 VAC to 240 VAC 50 60 Hz to the internal autoswitching power supply 2 BN
4. 4 Extron Electronics TON INTERFACING SWITCHING AND CONTROL User s Manual POARI Extron RGB 580 en AUDIO 83 232 68 M 626 I cc 240 OSA N RGB 580 Universal Remote Interface with Audio and ADSP 68 536 01 Rev F 09 09 Precautions Safety Instructions English This symbol is intended to alert the user of important operating and maintenance servicing instructions in the literature provided with the equipment This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may present a risk of electric shock Caution Read Instructions Read and understand all safety and operating instructions before using the equipment Retain Instructions The safety instructions should be kept for future reference Follow Warnings Follow all warnings and instructions marked on the equipment or in the user information Avoid Attachments Do not use tools or attachments that are not recommended by the equipment manufacturer because they may be hazardous Consignes de S curit Francais Ce symbole sert avertir l utilisateur que la documentation fournie avecle mat riel contient des instructions importantes concernant l exploitation et la maintenance r paration Ce symbole sert avertir l utilis
5. In addition a series of RGB 580xi CC AAP plates are also available for Extron Cable Cubby mounting In this manual RGB 580xi and remote interface are used interchangeably Features Stereo audio Unbalanced PC level stereo audio input can be output as balanced or unbalanced stereo audio Level and Peaking adjustments Level and peaking controls compensate for signal losses over long cable runs Level adjusts image brightness and peaking adjusts image sharpness Advanced Digital Sync Processing ADSP ADSP allows sync processing operations such as horizontal centering to occur without affecting the signal s sync timing This allows horizontal centering to be applied to signals that are output to digital display devices such as LCD projectors DLP projectors and plasma displays A front panel DIP switch provides another option Digital Display Sync Processing DDSPTV to ensure proper displays without altering sync pulse timing or width Remote contact closure A contact closure signal can be sent to the interface from the remote AAP RS 232 control A set of instructions are available via the Extron control software for Windows or any other remote RGB 580xi e Introduction 5 M 4 X RGB 580xi Remote Interface Chapter Two Installation and Setup Installation Overview Application Diagrams Front Panel Features and Cabling Rear Panel Features and Cabling Front Panel
6. 45 volts p p Select a level setting of 0 7 volts or above to compensate for the decrease in signal level that occurs when the signal passes through long cables Set the level at the maximum setting for cable lengths over 500 feet for all computer signals of 15 KHz to 135 KHz 2 10 RGB 580xi Installation and Setup 2 Peaking control The Video Output Peaking control affects the sharpness of a picture Increased peaking can compensate for detail mid and high frequency loss from low bandwidth system components or capacitance in long cables The minimum setting at the counterclockwise limit provides no peaking The maximum setting at the clockwise limit provides 100 peaking Adjust this control while viewing the displayed image to obtain the optimum picture sharpness Mounting the Optional AAP Device Various Extron RGB 580xi AAP double space devices may be mounted to any Extron product that has an AAP faceplate or to an Extron wallplate See appendix A for device part numbers The AAP device should be cabled before it is attached to a faceplate or wallplate see Cabling the AAP Device Rear Connectors in this chapter The screws needed for installing an AAP device are built into its front panel so no additional screws are needed 1 Insert the AAP s screws through the holes in the AAP faceplate or the AAP wallplate Secure the AAP device to the faceplate or wallplate with the provided captive washers and
7. CCODBOGLOTS 1 female 15 pin HD Video output RGB 580xi Number signal 1 analog RGBHV RGBS RGsB COLIDSCLIOPS 5 female Nominal 0 7 Vp p for RGB Minimum maximum levels 0 35 V to 1 45 Vp p 75 ohms 1056 0 30 dB 5 MHz DC E 5 mV maximum with input at 0 offset Video output RGB 580xi AAP RGB 580xi S AAP RGB 580xi SI AAP Numbert signal 1 analog RGBS RGsB 1 15 2 RGB 580xi Reference Sync Iripiit 49 DB oed RGBS RGsB RsGsBs De Mo RGBS RGsB 2 V to 5 5 Vp p with 50 2 VDC offset max Output 6 0 TTL 4 V to 5 Vp p unterminated Input IM B 510k ohms Output impedance 75 ohms Max propagation delay 85 ns rise fall time 215 Polarity Polarity follows input when is input and the sync polarity switch is set to Off Sync polarity is negative if the sync polarity switch is set to On RGBS RGSB Negative Audio G Unbalanced output 0 dB balanced output 6 dB Frequency response 20 Hz to 20 kHz 0 05 dB THD 0 0 03 1 kHz 0 3 20 KHz at nominal level gt 90 dB at maximum output balanced unweighted Stereo chan
8. au reut les batteries usagees conformement aux instructions du fabricant Vorsicht Stromquellen e Dieses Ger t sollte nur ber die auf dem Produkt angegebene Stromquelle betrieben werden Dieses Ger t wurde f r eine Verwendung mit einer Hauptstromleitung mit einem geerdeten neutralen Leiter konzipiert Der dritte Kontakt ist f r einen Erdanschlu amp und stellt eine Sicherheitsfunktion dar Diese sollte nicht umgangen oder aufer Betrieb gesetzt werden Stromunterbrechung Um das Ger t auf sichere Weise vom Netz zu trennen sollten Sie alle Netzkabel aus der R ckseite des Ger tes aus der externen Stomversorgung falls dies m glich ist oder aus der Wandsteckdose ziehen Schutz des Netzkabels e Netzkabel sollten stets so verlegt werden daf sie nicht im Weg liegen und niemand darauf treten kann oder Objekte darauf oder unmittelbar dagegengestellt werden k nnen Wartung Alle Wartungsmafsnahmen sollten nur von qualifiziertem Servicepersonal durchgef hrt werden Die internen Komponenten des Ger tes sind wartungsfrei Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall dieses Ger t selbst ffnen da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und oder andere Gefahren bestehen Schlitze und ffnungen e Wenn das Ger t Schlitze oder L cher im Geh use aufweist dienen diese zur Vermeidung einer Uberhitzung der empfindlichen Teile im Inneren Diese Offnungen d rfen niemals von ander
9. equipo ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos Ranuras y aberturas Si el equipo posee ranuras o orificios en su caja alojamiento es para evitar el sobrecalientamiento de componentes internos sensibles Estas aberturas nunca se deben obstruir con otros objetos Bater a de litio e Existe riesgo de explosi n si esta bater a se coloca en la posici n incorrecta Cambiar esta bater a nicamente con el mismo tipo o su equivalente recomendado por el fabricante Desachar las bater as usadas siguiendo las instrucciones del fabricante e Du ITF JN Dg x BU 5 e Hl E H 35 fee Fr ux 2 EF eH e HAERTER DORE P RES e PRERA uA Dit FCC Class ER 2 2 Ws 2j 4 FI Be SS 2 56 RIRE ARENDS TA Bust USB USA NCE A E Re HY HD o REP TER BD HFS ETP A AEE AHEM Ay PARES 3 1 ug BUR E f CARH FRE i FEE EFL 1960056 EME AOR TE BLA BUR UTP MEHE e EUR 5
10. s front panel LED lights green if the interface is receiving power 3 Check the cabling and the audio connector wiring and grounding and make adjustments as needed 4 For digital display devices including LCD DLP and plasma devices try turning DDSP on or off using the front panel DIP switch 5 To test the system setup and output substitute a video test generator for the computer input Unplug the power cords of the input output devices and the remote interface replace the video source with a then reconnect the power cords to restore AC power 6 Callthe Extron S3 Sales amp Technical Support Hotline if needed If the image is not displayed correctly 1 Ifthe output image looks too green the sync on green SOG DIP switch may be set to On and the display device may not be configured to handle SOG signals Set SOG to Off 2 If the picture bends or flags at the top of the screen set the serration pulse DIP switch to Off 3 For a display device that experiences intermittent glitches try turning DDSP on or off using the front panel DIP switch 4 Ifthe picture hangs off the left or right edge of the screen and an RGB 580xi S RGB 580xi CCS RGB 580xi SI AAP or RGB 580xi CCSI AAP device is connected to the interface adjust the AAP s horizontal shift H Shift control to center the image 5 If the edges of the image seem to exceed their boundaries or if thin lines and sharp edges lo
11. 0 10 to 90 noncondensing Operating 32 to 122 F 0 to 50 C 10 to 90 noncondensing COON Convection vents on sides Mounting Furniture mount Yes with included under desk mounting kit BC MOSS t DO Metal vented Enclosure dimensions RGB 580 1 1 75 H x 6 4 W x 6 0 D 4 4 16 3 cm W x 15 2 cm D Depth excludes connectors RGB 580xi AAP models 14 3 5 W 0 1 D 36 cm H x 8 9 W x 0 3 cm D double space high AAP plates 4 RGB 580xi Reference Circuit 1 3 H x 2 5 W x 0 9 D 3 3 cm H x 6 4 cm W x 2 3 cm D Depth excludes connectors knobs and faceplate Product weight RGB 580xi I AAP 3 RGB 580xi SI AAP 3 0 4 lbs 0 2 kg RGB 580xi AAP 3 RGB 580xi S AAP 3 0 5 Ibs 0 3 kg RGB 580xi AAP 6 RGB 580xi I AAP 6 0 6 lbs 0 3 kg RGB 580xi S AAP 6 RGB 580xi SI AAP 6 0 7 Ibs 0 3 kg RGB 580xi AAP 12 RGB 580xi S AAP 12 RGB 580xi SI AAP 12 1 0 Ibs 0 5 kg 1 2 165 0 5 Kg Shipping weight 216 1 kg 7 4 Ibs 2 kg Vibration 0 ISTA 1A in carton International Safe Transit Association Regulatory compliance voli E CE c DL UL ENILZENIC CE C tick FCC Class A ICES VCCI MTBE E 30 000 hours 3 years parts and labor Mensa All nominal levels are at 1096 Specifications are s
12. 2 26 521 08 3 6 m RGB 580xi AAP replacement cable 25 7 6 m 26 521 04 580xi replacement cable 35 10 6 m 26 521 05 RGB 580xi Reference A 7 Specifications Part Numbers Accessories cont d A 8 RGB 580xi Reference 7 RGB 580xi Remote Interface Appendix B Mounting Template Dimensions Dimensions for Mounting Dimensions For under desk mounting use the bracket mounting kit that is included with the RGB 580xi and see the template diagram below 61 The template shown below is not drawn to scale and is to be used for dimensional reference only 6 95 g 6 35 1 79 x 6 35 OPENING IN DESK requires mounting kit P N 70 077 01 Recommended pilot drill hole size di for supplied screws 3 32 x 1 4 deep Pd AS requires mounting P kit P N 70 077 02 y Un Through desk mounting template der desk mounting template Rear Location Recommended pilot drill hole size for supplied screws 3 32 x 1 4 deep Front Location Iu RGB 580xi NOTE AII dimensions are in inches FRONT Mounting Bracket Templates Drawing not to scale B 2 RGB 580xi Mounting Template Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purcha
13. 4 40 nuts AAP 102 Cable RGB 580xi SI AAP 34 40 Nut w Captive Washer Example of mounting an AAP device to a wallplate 2 Follow steps 3 through L in the Installation Overview section of this chapter RGB 580xi e Installation and Setup 2 11 Installation and Setup cont d AAP Device Features RGB 580xi AAP T RGB 580xi S AAP AUDIO IN A AUD O IN 2 12 57 efje RGB 580xi e SELECT A COMPUTER IN Ce Q A 2 RGB 580xi 1 RGB 580xi SI AAP UD O IN e COMPUTER IN 580 1 Power signal LED This LED lights e amber to indicate that the AAP device is receiving power e green to indicate that an active sync signal is present at the input and that the AAP device is receiving power The LED flashes green whenever the minimum and maximum limits of the horizontal shift control shift have been reached 2 RGB video input connector Attach a cable from the computer source to this 15 pin HD female connector 3 Audio input connector Plug a 3 5 mm stereo plug into this jack for unbalanced audio input Wire the male plug as shown below Tip L lt Sleeve 4 Horizontal shift control knob Shift While viewing the displayed image rotate this control to move the image to the right or left on the screen The power signal LED flas
14. Adjustments Mounting the Optional AAP Device AAP Device Features Cabling the AAP Device Rear Connectors Cable Cubby AAP Device Features Cabling the Cable Cubby AAP Devices Troubleshooting Installation and Setup Installation Overview 2 2 CAUTION Installation and service must be performed by authorized personnel only To install and set up an RGB 580xi follow these steps H Turn all of the equipment off Make sure that the computer the RGB 580xi and the output devices projector monitor speakers are all turned off and disconnected from the power source D For under desk mounting A Determine the installation location table desk podium or other suitable location If Architectural Adapter Plates are to be connected to the interface consider where they will be located in relation to the interface See Application Diagrams in this chapter B Mount the interface See Under furniture mounting in this chapter Attach output cables to the rear panel of the interface and to the output devices See Rear Panel Features and Cabling in this chapter Attach input cables to the input devices and to the interface s front panel connectors See Front Panel Features and Cabling in this chapter Set the front panel DIP switches Use the Front Panel Features and Cabling section of this chapter as a guide e e Connect power cords and turn on the output devices projector monitor speakers
15. C output connectors Connect coaxial cables from a display device to these for one RGBHV RGBS or RGsB RsGsBs video output as follows e RGsB Sync on Green RsGsBs output only if input is RsGsBs 3 Audio output connector Cable an audio device to the interface via this female 5 pole captive screw connector Wire the male connector as shown below NO Ground Here TN Ring pot Sleeve s 1 H Sleeve s a Tip NO Ground Here po Ring p Unbalanced Audio Output Balanced Audio Output CAUTION For unbalanced audio connect the E 3 5 sleeve s to the ground contact DO NOT connect sleeve s to the Do not tin the wires negative contacts 4 RS 232 connector Connect an RS 232 device control system or PC computer to this female 3 pole captive screw connector for two way RS 232 communication Software for RS 232 control is included with the interface See chapter three Remote Control for information on how to install and use the control software and SIS commands Wire the male connector as shown below 5 Receive O Transmit GL 3 x Ground 9 655 54 g RGB 580xi Installation and Setup 2 9 Installation and Setup cont d Front Panel Adjustments Video signals passing through long cable runs of over 125 feet 38 1 meters can decrease in strength creating
16. Command Response host to interface interface to host NOTE Whenever the Input Select button on the AAP device is pressed contact closure is initiated at the 580xi remote interface and a signal is sent from the remote interface s RS 232 port Additional description Contact closure has been detected across pins 1 and 2 Horizontal shift Specify horizontal shift X1 H Hph x1 1 Shift right one step H Hph Xi 1 Shift left one step Hph 1 Set horizontal shift value Increment up Increment down Firmware version part number amp information requests and reset Query firmware version number Q q 2 Request part number N n 60 362 01 4 Request information I i see below Display version Ver x xx Display interface s part Display status p 3uo uomnejodo Windows Based Program Control The included graphical control software for Windows offers another way to control the interface via RS 232 in addition to the Simple Instruction Set commands listed on page 3 4 The control software is compatible with Windows 2000 Windows XP and later versions of Windows Upgrades to the program can be downloaded from the Extron Web site www extron com Installing the software The control program is contained on the included disk To install the program insert the disk into the computer s drive If the setup program does not start automatic
17. Control connector J4 Insert wires into and tighten the screws on the 3 5 mm 5 pole captive screw connector This connector is used for contact closure and horizontal shifting signals Wire the connector as shown in the following illustration Horizontal shift green ass 60 Horizontal shift ground gray 6 n Horizontal shift brown 3 Jo Contact closure blue gt 6 a f H Contact closure purple 1043409 2 LED connector J2 Insert wires into and tighten the screws on the 3 5 mm 3 pole captive screw connector This connector is used for powering the green and amber LEDs Wire the connector as shown in the following illustration Green LED pink QU 3 LED ground yellow 3 Amber LED orange 3 H The and audio cable assemblies are routed through the Cable Cubby Refer to the Cable Cubby User s Manual part 68 701 01 for Cable Cubby installation instructions Troubleshooting Turn on the input devices computer audio device and output device s projector monitors speakers The image should now appear on the screen and sound should be audible RGB 580xi e Installation and Setup 2 17 Installation and Setup cont d If the image does not appear or there is no sound 1 Ensure that all devices are plugged in 2 Make sure that each device is receiving power The interface
18. GB 580xi e Installation and Setup 2 13 Installation and Setup cont d 2 14 Horizontal shift green Horizontal shift ground gray Horizontal shift brown Contact closure light blue Contact closure purple 1041409 2 LED connector J2 Insert wires into and tighten the screws on the 3 5 mm 3 pole captive screw connector This connector is used for powering the green and amber LEDs Wire the connector as shown in the following illustration Green LED pink ed ms LED ground yellow LL m Amber LED orange QJ s Audio output connector J3 Insert wires into and tighten the screws on the 3 5 mm 3 pole captive screw connector This connector is used for unbalanced stereo audio output Wire the connector as shown in the following illustration lt 3 5 mm lt Audio left white e Audio ground black x Audio right red Lass H 1 RGB 580xi Installation and Setup Cable Cubby Device Features HORIZONTAL HORIZONTAL SHIFT INPUT SELECT RGB 580xi CCS AAP RGB 580xi CCSI AAP Installation of the RGB 580xi CC AAP devices in a Cable Cubby allows the VGA and audio cable connectors of the CC AAP device to be accessible as shown in the following diagram RGB 580 CCSI CC AAP VGA connector CC AAP Audio connector Cable Cubby RGB 580xi e Installation and Setup 2 15 Installation
19. MP SYNC oa RGB 580xi_ RGB 580xi front panel Power signal LED This LED lights amber to indicate that the RGB 580xi interface is receiving power and lights green to indicate it is receiving both power and an input signal Audio input connector Plug a 3 5 mm stereo plug into this jack for unbalanced audio input Wire the male plug as shown below Tip L Ring R gt e e e 2 Sleeve Audio input wiring RGB 580xi e Installation and Setup RGB video input connector Attach a cable 6 10 9 1 5 from the computer source to the RGB 580xi via this 15 pin HD female connector The 0 O 15 pin HD male connector pin locations and 11 5 pinout table are shown here 15 pin HD male pin out table Description Wire ID Pin Description Wire ID red signal red coax 10 horizontal sync ground black coax shield green signal green coax 10 vertical sync ground yellow coax shield blue signal blue coax 10 audio ground black wire horizontal shift 4 green wire 10 LED ground yellow wire horizontal shift brown wire 10 shift ground grey wire red coax ground red coax shield TEIL audio right red wire green coax ground green coax shield 12 audio left white wire blue coax ground blue coax shield 13 horizontal sync black coax LED red orange wire 14 vertical sync yellow coax 15 LED green pink wire 4 Contact closure control connector Connect an optional contact closure device to this female 5 pole captiv
20. Next power up the remote interface and then the audio and video input devices The picture should appear and sound should be audible If not ensure that all devices are plugged in and receiving power Check the cabling and make adjustments as needed While watching the display adjust the video level and peaking by using the rotary Level and Peaking controls See Front Panel Adjustments in this chapter RGB 580xi Installation Under furniture mounting 1 Attach the under desk mounting brackets part 70 077 01 to the interface with the four machine screws provided in the mounting kit as shown below This procedure may also apply to table or podium mounting applications See Application Diagrams in this chapter Hold the interface with attached brackets against the underside of the desk or other furniture Mark the location of holes for screws on the desk See appendix B for mounting dimensions Drill 1 4 inch 6 4 mm deep 3 32 inch 2 38 mm diameter pilot holes in the table or desk at the marked screw locations from the underside or inside concealed side of the furniture where the interface will be located Insert the four wood screws into the pilot holes Fasten each screw into the installation surface until just less than 1 4 inch of the screw protrudes Align the installed screws with the slots in the mounting brackets and place the interface against the surface with the screws through the bracket sl
21. ally run Launch exe from the disk and follow the instructions that appear on the screen By default the installation creates a C Program Files Extron Electronics folder containing the RGB 580 Windows control program An icon may be placed on the Windows desktop Using the software To run the control program follow these steps 1 Double click on the RGB 302 304 Control Pgm icon in the Extron Electronics group or folder The Comm menu appears on the screen 2 Click the comm port that is connected to the interface s RS 232 port The control software looks for the interface at that port and reads its configuration The control program window shown below appears and displays current settings Extron s RGB 202 302 304 580 File Help HORZ RGB 580xi Remote Control 3 5 Operation cont d For information on program features press the F1 computer key click on the Help menu from within the control program or double click the RGB 302 304 Help icon in the Extron Electronics group or folder Em 201 Control Program S i 201 Help Ey 302 304 Control Pam o 302 304 Help Contact Closure Remote Control For contact closure connect a contact closure remote control device to the front panel s contact closure female 5 pole captive screw connector Various AAP devices and cable assemblies are also available from Extron to provide remote contact closure c
22. and Setup cont d 1 Power signal LED This LED lights e amber to indicate that the CC AAP device is receiving power e green to indicate that an active sync signal is present at the input and that the CC AAP device is receiving power Te LED flashes green whenever the minimum and maximum limits of the horizontal shift control H shift have been reached 2 Horizontal shift control knob While viewing the displayed image rotate this control to move the image to the right or left on the screen The power signal LED flashes green whenever the minimum and maximum limits of this control are reached NOES DDSP disables the horizontal shifting control 3 Input select button Pressing this button results in contact closure between pins A and B of the contact closure control connector on the front panel of the RGB 580xi Cabling the Cable Cubby AAP Devices Extron s various CC AAP devices for the RGB 58027 come with rear panel connectors that may require cabling NOTE Although the control cable LED cable assembly comes prewired to the captive screw connectors any subsequent connector replacement will require the following cabling instructions To cable the captive screw connectors refer to the following diagrams and orient the wires according to the view angle of the captive screws 2 16 RGB 580xi Installation and Setup HORIZONTAL SHIFT INPUT SELECT RGB 580xi CCSI AAP 1
23. apability The pin assignments for the RGB 580xi s contact closure connector are shown in the following table 3 6 Pin Contact closure A Contact closure B Contact closure C 5V D Gnd E 5V Description Contact closure circuit Contact closure circuit 5V source for powering AAP devices Signal ground for powering AAP devices 5V source for powering AAP devices RGB 580xi Remote Control amp 2 X RGB 580xi Remote Interface Appendix Reference Specifications Included Parts Optional AAP Devices Optional Cable Cubby AAP Devices Optional RGB 580xi AAP Extension Cables Specifications Part Numbers and Accessories Specifications Video RGB 580xi lig 0 35 V to 1 45 Vp p 300 3 Video input RGB 580xi Numb r signal 1 analog RGBS RGsB RsGsBs female 15 pin HD 1 Nominal level 0 7 Vp p for RGB Minimum maximum levels Analog 0 3 V to 1 45 Vp p with no offset ohms or high Z switchable set to 75 75 ohms if no local monitor is connected Horizontal frequency Autoscan 15 kHz to 150 kHz Vertical eguen yeere Autoscan 40 Hz to 140 Hz 8 lt 30 dB 5 MHz DC offset max allowable 20 V Video input RGB 580xi AAP RGB 580xi S AAP RGB 580xi SI AAP Number signal 1 analog RGBHV RGBS RGsB RsGsBs
24. ateur de la pr sence dansle boitier del appareil de tensions dangereuses non isol es posant des risques d lectrocution Attention Lire les instructions Prendre connaissance de toutes les consignes de s curit et d exploitation avant d utiliser le mat riel Conserver les instructionse Ranger les consignes de s curit afin de pouvoir les consulter l avenir Respecter les avertissements Observer tous les avertissements et consignes marqu s sur le mat riel ou pr sent s dans la documentation utilisateur Eviter les pi ces de fixation Ne pas utiliser de pi ces de fixation ni d outils non recommand s par le fabricant du mat riel car cela risquerait de poser certains dangers Sicherheitsanleitungen Deutsch Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung Instandhaltung geben Dieses Symbol soll den Benutzerdarauf aufmerksam machen da im Inneren des Geh uses dieses Produktes gef hrliche Spannungen dienichtisoliert sind und die einen elektrischen Schock verursachen k nnen herrschen Achtung Lesen der Anleitungen Bevor Sie das Ger t zum ersten Mal verwenden sollten Sie alle Sicherheits und Bedienungsanleitungen genau durchlesen und verstehen Aufbewahren der Anleitungen Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie aufbewahren damit Sie im Bedarfsfall darauf zur ckgreifen k nnen Be
25. e screw connector Making contact closure between pins A and B transmits a channel signal through the RS 232 port Extron RGB 580xi I and RGB 580xi SI CCSI AAP see AAP Device Features and Cable Cubby AAP Device Features in this chapter provide a one button contact closure operation Wire the male connector as shown below on the left Extron VGA and control cable assembly see chapter A Optional RGB 580xi AAP Replacement Cables comes with the male control connector prewired as shown at right Prewired male control connector Contact Closure Contact closure Ces 4 d Contact closure 6 4 do 5VDC Co r OL G Ground Ee f 5 Cor _ Jn Contact closure wiring Prewired male control cable connector Pin Contact closure Description A Contact closure Contact closure circuit B Contactclosure Contact closure circuit C 5V 5V source for powering AAP devices D Gnd Signal ground for powering AAP devices 5V 5V source for powering AAP devices The contact closure pins on the RGB 580xi s front panel are not to be used for horizontal shift control See the horizontal shift control wiring in the 15 pin HD pin out table in on the previous page Video output level control This control adjusts picture brightness by compensating for signal amplitude loss caused by cable resistance See Front Panel Adjustments in this chapte
26. en Objekten blockiert werden Litium Batterie Explosionsgefahr falls die Batterie nicht richtig ersetzt wird Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp der auch vom Hersteller empfohlen wird Entsorgen Sie verbrauchte Batterien bitte gem t den Herstelleranweisungen Advertencia Alimentaci n el ctrica Este equipo debe conectarse nicamente a la fuente tipo de alimentaci n el ctrica indicada en el mismo La alimentaci n el ctrica de este equipo debe provenir de un sistema de distribuci n general con conductor neutro a tierra La tercera pata puesta a tierra es una medida de seguridad no puentearia ni eliminaria Desconexi n de alimentaci n el ctrica Para desconectar con seguridad la acometida de alimentaci n el ctrica al equipo desenchufar todos los cables de alimentaci n en el panel trasero del equipo o desenchufar el m dulo de alimentaci n si fuera independiente o desenchufar el cable del recept culo de la pared Protecci n del cables de alimentaci n Los cables de alimentaci n el ctrica se deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos Reparaciones mantenimiento Solicitar siempre los servicios t cnicos de personal calificado En el interior no hay partes a las que el usuario deba acceder Para evitar riesgo de electrocuci n no intentar personalmente reparaci n mantenimiento de este
27. folgen der Warnhinweise Befolgen Sie alle Warnhinweise und Anleitungen auf dem Ger t oder in der Benutzerdokumentation Keine Zusatzgerate Verwenden Sie keine Werkzeuge oder Zusatzger te die nicht ausdr cklich vom Hersteller empfohlen wurden da diese eine Gefahrenquelle darstellen k nnen Instrucciones de seguridad e Espanol Este s mbolo se utiliza para advertir al usuario sobre instrucciones importantes de operaci n y mantenimiento o cambio de partes que se desean destacar en el contenido de la documentaci n suministrada con los equipos Este s mbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protecci n aislante que puedan encontrarse dentro de la caja o alojamiento del producto y que puedan representar riesgo de electrocuci n Precaucion Leer las instrucciones Leer y analizar todas las instrucciones de operaci n y seguridad antes de usar el equipo Conservar las instrucciones Conservar las instrucciones de seguridad para futura consulta Obedecer las advertencias Todas las advertencias e instrucciones marcadas en el equipo o en la documentaci n del usuario deben ser obedecidas Evitar el uso de accesorios No usar herramientas o accesorios que sean especificamente recomendados por el fabricante ya que podrian implicar riesgos Warning Power sources This equipment should be operated only from the power source indicated on the product Th
28. hes green whenever the minimum and maximum limits of this control are reached 11511 3 DDSP disables the horizontal shifting control RGB 580xi e Installation and Setup 5 Input select button Pressing this button results in contact closure between pins A and B of the contact closure control connector on the front panel of the RGB 580xi Cabling the AAP Device Rear Connectors Various Extron AAP devices for the RGB 580xi may come with several rear connectors that require cabling Although the VGA and control cable LED assembly comes prewired to the captive screw connectors any subsequent cable assembly replacement will require the following cabling instructions To cable the captive screw connectors refer to the following diagrams and orient the wires according to the view angle of the captive screws When using the Extron VGA and control cable assembly see appendix A Optional RGB 580xi AAP Replacement Cables for part numbers refer to the color of each wire for signal identification SHIFT SELECT AUDIO IN COMPUTER IN OO RGB 580xi e Blue I Purple White Yellow Green Blac Pink Gray Orange Brown Example of AAP device rear connectors 1 Control connector J4 Insert wires into and tighten the screws on the 3 5 mm 5 pole captive screw connector This connector is used for contact closure and horizontal shifting signals Wire the connector as shown in the following illustration R
29. is equipment is intended to be used with a main power system with a grounded neutral conductor The third grounding pin is a safety feature do not attempt to bypass or disable it Power disconnection To remove power from the equipment safely remove all power cords from the rear of the equipment or the desktop power module if detachable or from the power source receptacle wall plug Power cord protection Power cords should be routed so that they are not likely to be stepped on or pinched by items placed upon or against them Servicing Refer all servicing to qualified service personnel There are no user serviceable parts inside To prevent the risk of shock do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards Slots and openings If the equipment has slots or holes in the enclosure these are provided to prevent overheating of sensitive components inside These openings must never be blocked by other objects Lithium battery There is a danger of explosion if battery is incorrectly replaced Replace it only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Avertissement Alimentations Ne faire fonctionner ce mat riel qu avec la source d alimentation indiqu e sur l appareil Ce mat riel doit tre utilis avec une alimentation principale comportan
30. nal AAP Devices A 6 Optional Cable Cubby AAP Devices A 7 Optional RGB 580xi AAP Replacement Cables A 7 RGB 580xi e Table of Contents TOC i Table of Contents cont d Appendix B gt Mounting Template B 1 Dimensions ethernet nnne B 2 AII trademarks mentioned in this manual are the properties of their respective owners TOC ii RGB 580xi e Table of Contents 580xi Remote Interface Chapter One Introduction About the RGB 580xi Features Introduction About the RGB 580xi The Extron RGB 580xi is an analog remote mountable computer video interface that can be installed in a location that is hidden from the user s view It features a 300 MHz 3 dB video bandwidth It accepts one analog computer video input RGBHV RGBS RGsB or RsGsBs on a 15 pin HD female connector and one unbalanced stereo audio input on a 3 5 mm stereo female jack Five female connectors provide video output RGBS and RGsB and a five pole captive screw connector provides stereo audio output A variety of Architectural Adapter Plates AAP with A V inputs can be used in conjunction with the RGB 580xi and are ideal for installation in remote locations including discreet mounting in the Extron Hideaway Surface Access Products such as the HSA 400 HSA 402 and HSA 822
31. nel separation gt 90 dB 1 kHz to 20 kHz Audio input Number signal type PC level stereo unbalanced 8 1 3 5 mm stereo mini audio jack female tip ring sleeve uode dones gt 5 ohms unbalanced DC coupled Nominal 10 dBV 316 mV Maximum level 8 5 dBu balanced or unbalanced at 1 THD N 0 dBu 0 775 Vrms 0 dBV 1 Vrms 0 dBV 2 dBu RGB 580xi Reference A 3 Specifications Part Numbers Accessories cont d Audio output Number signal type 1 buffered stereo 2 channel balanced unbalanced CONNECTIONS ee 1 3 5 mm captive screw connector 5 pole 50 ohms unbalanced 100 ohms balanced 0 1 dB channel to channel Maximum level 600 ohm gt 14 dBm balanced or unbalanced at 1 THD N Control remote interface Serial control RS 232 captive screw connector 3 pole Baud rate and 9600 baud 8 data bits 1 stop bit no parity Serial control pin configuration 1 TX 2 RX 3 GND Program Extron control configuration program for Windows Extron Simple Instruction Set 515 General Power RGB ercer 100 VAC to 240 VAC 50 60 Hz 18 watts internal 1 Storage 40 to 158 F 40 to 7
32. ok thick and fuzzy try changing the Peaking control setting If the image is too bright or dark try changing the Level control setting 6 If the image still does not display correctly call the Extron 53 Sales amp Technical Support Hotline 2 18 580 Installation and Setup 7 RGB 580xi Remote Interface Chapter Three Remote Control RS 232 Programmer s Guide Control Software for Windows Contact Closure Remote Control Operation There are two ways to control the horizontal shifting feature of an RGB 580xi remote interface by using the AAP horizontal shift shift control or by using an RS 232 remote control device RS 232 Programmer s Guide The interface can be remotely controlled via a host computer attached to the rear panel s 3 pole captive screw 5 232 connector A contact closure control system may also be used by connecting a contact closure device to the front panel s female 5 pole captive screw connector The protocol is 9600 baud 1 stop bit no parity and no flow control The RS 232 control device host can use RS 232 either the Extron Simple Instruction Set SIS commands or the graphical control program for Windows RS 232 control software is Captive Screw Pin Locations included with the interface romale The rear panel s RS 232 3 pole female connector has the following pin assignments Pin RS 232 function Description Transmit data Receive data Signal ground Hos
33. ots Slide the interface slightly forward or back then tighten all four screws to fasten it in place Under desk mounting of the RGB 580xi RGB 580xi Installation 2 3 Installation and Setup cont d Application Diagrams The RGB 580xi can be hidden from view and remotely connected to a computer through various Extron AAP and Cable Cubby CC AAP devices that are installed in office furniture or walls Please consult with your Extron sales representative concerning these AAP and CC AAP devices and AAP capable products from which devices may be installed Sound System Extron RGB 580xi SI AAP Mounted in the Extron AAP 102 Extron RGB 580xi Remote Interface Podium mounting of the RGB 580xi with an AAP device Mounted through a table or podium 2 QF Mounted under a table or podium Table mounting of the RGB 580xi with an AAP device 2 4 RGB 580xi Installation and Setup RGB 580xi CCSI AAP LAN WAN Network Internet Extron RGB 580xi RGB 580xi Podium mounting of the RGB 580xi with a Cable Cubby AAP device Refer to the Cable Cubby User s Manual part 68 701 01 for Cable Cubby installation instructions RGB 580xi Installation and Setup 2 5 Installation and Setup cont d Front Panel Features and Cabling 2 6 Pi 5 Ir CON RoE VIDEO OUTPUT V SYNC WIDTH NEG SYNC CO
34. r Video output peaking control This control adjusts picture sharpness by compensating for cable capacitance caused by long cable runs See Front Panel Adjustments in this chapter DIP switches This bank of DIP E NEG SYNC switches controls DDSP Digital Display ose Ir OT Sync Processing serration pulse output SOG sync on green output vertical sync width sync polarity and composite sync output Moving a switch up sets it to On and moving it down sets it to Off default for all DIP switches is Off down RGB 580xi Installation and Setup 2 7 Installation and Setup cont d 1 DDSP Digital Display Sync Processing This feature may be necessary for digital display devices such as LCD DLP digital light processing and plasma displays Use this option if the image is not displayed properly after other options such as serration pulse and vertical sync pulse width have been explored The interface uses DDSP instead of ADSP DDSP does not process the sync signal Mei DDSP disables the horizontal shifting control Off The interface performs sync processing operations such as centering with ADSP 2 Serr serration pulse Many LCD and DLP projectors and plasma displays must have serration pulses removed from the sync signal in order to display properly Flagging or bending at the top of the video image is a sign that the serration pulses should be removed On
35. reserved
36. se In the event of malfunction during the warranty period attributable directly to faulty workmanship and or materials Extron Electronics will at its option repair or replace said products or components to whatever extent it shall deem necessary to restore said product to proper operating condition provided that it is returned within the warranty period with proof of purchase and description of malfunction to USA Canada South America Japan and Central America Extron Japan Extron USA Kyodo Building 16 Ichibancho 1001 East Ball Road Chiyoda ku Tokyo 102 0082 Anaheim CA 92805 Japan USA Ehina Europe Africa and the Middle Fast Extron China Extron Europe 686 Ronghua Road Hanzeboulevard 10 Songjiang District 3825 PH Amersfoort Shanghai 201611 The Netherlands China Asia Middle East Extron Asia Extron Middle Fast 135 Joo Seng Road 04 01 Dubai Airport Free Zone PM Industrial Bldg F12 PO Box 293666 Singapore 368363 United Arab Emirates Dubai Singapore This Limited Warranty does not apply if the fault has been caused by misuse improper handling care electrical or mechanical abuse abnormal operating conditions or non Extron authorized modification to the product If it has been determined that the product is defective please call Extron and ask for an Applications Engineer at 714 491 1500 USA 31 33 453 4040 Europe 65 6383 4400 Asia or 81 3 3511 7655 Japan to receive an Return Authorization n
37. signalloss The longer the cable the greater the cable resistance and capacitance and the greater the level and peaking adjustments that will be required to compensate for the resultant signal loss These adjustments change the level and peaking of the output signal to compensate for capacitance caused by up to 1000 feet 304 8 meters of Extron SHR cable If the displayed image is too bright or too dark try changing the level setting If the edges of the displayed image seem to exceed their boundaries or if thin lines and sharp edges look thick and fuzzy try changing the peaking setting See the illustration below 1 Leveladjustment control The Video Output Level control alters the brightness of the displayed image To adjust the video output level view the display while using a small flat blade screwdriver to rotate this one turn potentiometer You can judge the adjustment visually by looking at the display If the interface receives a typical 0 7 volts p p analog computer video input the output is as follows e Atthe minimum level setting the counterclockwise limit of this control the interface outputs video at 0 5 volts p p e Unity level is 0 7 volts the same as the input signal Set the control to approximately one half turn between the minimum and maximum level settings to output unity level video e At the maximum level setting the clockwise limit of this control the interface outputs video at 1
38. sure switch RGB 580xi I AAP and RGB 580xi SI CCSI Error responses When the interface receives a valid SIS command it executes the command and sends a response to the host device If the interface is unable to execute the command because the command is invalid or it contains invalid parameters it returns an error response to the host The error response codes and their descriptions are as follows E10 Invalid command E13 Invalid value the number is out of range Using the command response table The command response table lists valid command ASCII codes the interface s responses to the host and a description of the command s function or the results of executing the command Lowercase characters are acceptable in the command field only where indicated The ASCII to HEX conversion table below is for use with the command response table ASCII to HEX Conversion Table EsciB CR OD LF 2 6 gt 5 V f k n S V x RGB 580xi Remote Control 3 3 6 104340 e 085 898 The command table page uses symbols defined below to represent variables Symbol definitions sel Shift control range 63 to 63 carriage return line feed hex OD 0A Controller firmware version listed to two decimal Space places e g x xx Frequency in Hz or kHz listed as xxx xx Command response table Command description ASCII
39. t to interface communications SIS commands consist of one or more characters per field No special characters are required to begin or end a command sequence When a command is valid the interface executes the command and sends a response to the host device All responses from the interface to the host end with a carriage return and a line feed CR LF 1 which signals the end of the response character string A string is one or more characters Interface initiated messages When a local event such as a front panel or contact closure selection or adjustment takes place the interface sends a message to the host No response is required from the host The interface initiated messages are listed here underlined C Copyright 2001 Extron Electronics RGB 580xi Vx xx el The interface displays the copyright message when it first powers on Vx xx is the firmware version number 3 2 RGB 580xi Remote Control RECONFIG 1 When the remote interface s RGB video input is disconnected or the horizontal shift control H shift is adjusted from the AAP device RGB 580xi S CCS and RGB 580xi SI CCSI the interface sends the reconfiguration message No response is required from the RS 232 host but the host may request a new status listing via the request information command I i See the command response table in this chapter for details Chn 4 A contact closure selection has been detected from the remote AAP contact clo
40. t un fil de terre neutre Le troisi me contact de mise la terre constitue un dispositif de s curit n essayez pas de la contourner ni de la d sactiver D connexion l alimentatione Pour mettre le mat riel hors tension sans danger d connectez tous les cordons d alimentation de l arri re de l appareil ou du module d alimentation de bureau s il est amovible ou encore de la prise secteur Protection du cordon d alimentation e Acheminer les cordons d alimentation de mani re ce que personne ne risque de marcher dessus et ce qu ils ne soient pas cras s ou pinc s par des objets R paration maintenance Faire ex cuter toutes les interventions de r paration maintenance par un technicien qualifi Aucun des l ments internes ne peut tre r par par l utilisateur Afin d viter tout danger d lectrocution l utilisateur ne doit pas essayer de proc der lui m me ces op rations car l ouverture ou le retrait des couvercles risquent de l exposer de hautes tensions et autres dangers Fentes et orifices Si le boitier de l appareil comporte des fentes ou des orifices ceux ci servent emp cher les composants internes sensibles de surchauffer Ces ouvertures ne doivent jamais tre bloqu es par des objets Lithium Batterie Il a danger d explosion s ll y a remplacment incorrect de la batterie Remplacer uniquement avec une batterie du meme type ou d un ype equivalent recommande par le constructeur Mettre
41. ubject to change without notice RGB 580xi Reference A 5 Specifications Part Numbers Accessories cont d Included Parts These items are included in each order for an RGB 580xi Included parts Replacement part number RGB 580xi 60 362 01 3 5 mm 5 pole captive screw connectors 10 100 460 01 3 5 mm 3 pole captive screw connectors 10 125 Under desk mounting kit RGB 580xi User s manual 100 459 01 70 077 01 Windows based control software IEC power cord Tweeker Optional AAP Devices RGB 580xi AAP 3 0 9 m black white 70 128 02 03 RAL9010 white 05 RGB 580xi AAP 6 1 8 m black white 70 129 02 03 RAL9010 white 05 RGB 580xi S AAP 0 9 m black white 70 134 02 03 RGB 580xi S 6 1 8 m black white 70 135 02 03 RGB 580xi SI AAP 3 0 9 m black white RGB 580xi SI AAP 6 1 8 m black white 0 137 02 03 70 159502 A 6 RGB 580xi Reference Optional Cable Cubby Devices RGB 580xi CCS AAP 9 2 7 m black 70 254 02 RGB 580xi CCS AAP 12 3 6 m black 70 255 02 RGB 580xi CCSI AAP 9 2 7 m black 70 256 02 RGB 580xi CCSI AAP 12 3 6 m black 70 257 02 Optional RGB 580xi AAP Replacement Cables These cables apply only to the RGB 580xi AAP RGB 580xi S and RGB 580xi SI they do not apply to the RGB 580xi CCS or RGB 580xi CCSI RGB 580xi AAP replacement cable 1
42. umber This will begin the repair process as quickly as possible Units must be returned insured with shipping charges prepaid If not insured you assume the risk of loss or damage during shipment Returned units must include the serial number and a description of the problem as well as the name of the person to contact in case there are any questions Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality performance merchantability or fitness for any particular use no event will Extron Electronics be liable for direct indirect or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage Please note that laws vary from state to state and country to country and that some provisions of this warranty may not apply to you Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters 800 633 9876 800 3987 6673 800 7339 8766 81 3 3511 7655 400 883 1568 971 4 2991800 800 633 9876 Inside USA Canada Only Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX Inside USA Canada Only 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 1 714 491 1500 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX 1 714 491 1517 FAX 2009 Extron Electronics All rights
Download Pdf Manuals
Related Search