User Manual (4) Enclosure Assembly (5) System Set Up (1
Contents
1. SK 5250 USB 2 0 f inonnonnnnoonnononnovonnony SK 5250 52 f OOOOOOOODOODOONDONOONONNINO 9 LU 7 h Note Product specifications and design may change or differ from illustration at anytime without prior notice 6 Safety Information Location and placing precautions Do not cover the SK 5250 and do not place the unit on other heat sensitive equipment Avoid positioning it in the following places e Locations with direct sunlight next to radiators or other sources of heat with high temperatures more than 35 C or high humidity more than 90 e Locations subject to vibration shock or with a slope e Do not expose the product to water or humid conditions Electricity and power plug Careful attention must be paid to the following points in order to avoid operational faults and electric shock or fire e When removing the power cable from the socket always pull on the plug fixture and never on the cord e Do not touch the power cable with wet hands e Never try to repair or modify the power cable yourself e If the unit should emit smoke an unusual odour or noise switch it off immediately and unplug the power cable Cables Use only the cables supplied or recommended by your vendor in order to avoid any sort of malfunction 3 Drive Assembly a Remove the screws located at the bottom of the case and pull out the chassis from the enclosure b Install the2. System Set Up If the drive has been pre installed and setup already you do not need to prepare anything else and can use it straight out of the box If you have purchased an empty enclosure make sure the drive is properly installed before you connect it to your computer and turn on the power a Turn on your computer and start the system b Plug in the external power supply connect the SK 5250 to the computer and turn on the power c The system will automatically mount the drive and you can access it under My Computer for the PC or on your desktop for the Mac d If the drive does not show up make sure a DVD has been inserted and and the correct drive has been selected in your media player or DVD burning software e For the safe removal of your drive and to assure that no data is lost always eject the external drive from your system first before you turn it off Note When not in use for longer periods of time it is recommended to turn off the device and unplug the power supply a a eh te ts ty ly uae eh Gh el it i lh um ie sm a mam te um ya uh i ms ir Fil um ipsum mh ih uh uma am ci uy a ia ll esa tm iy ih fm ip mids Sst em ma my eam usa Gm itr Fy iy ms ip tm us Gl Gah my mi a SG ut my ir Sl i 2 Detailed View The available interfaces depend on the model you have purchased
3. drive connect the SATA and power cable and then mount the drive with the four screws from the side Note Your unit may come with a pre installed drive Before opening your enclosure please read the warranty carefully as this could void it Q Can install a hard drive A No this enclosure is designed for optical disc drives only Q Can I use my device with bus power only A No an external power supply is always required Q Can I use more than one interface at the same time A No only one interface can be used at any given time Disconnect the previous cable before connecting the new one 2009 by Macpower amp Tytech Technology Co Ltd All Rights Reserved The information contained in this document is believed to be accurate and reliable Macpower amp Tytech assumes no responsibility for any errors or differences between the product you may have and the one mentioned in this document and reserves the right to make changes in the specifications and or design of this product without prior notice The diagrams contained in this document are for reference and may not fully represent the real product
4. Sr S59 User Manual C August 18 2009 v1 1 For more information visit our website at www macpower com tw 4 Enclosure Assembly a Slide the assembled drive back into the enclosure but be careful not to damage any of the components b Fasten the 4 screws at the bottom of the casing to finish the assembly Next peel off the paper from the back of the self adhesive rubber feet Now place the rubber feet over the screws and stick them on the casing to cover the screws Note Be careful not to damage any components when installing the drive 1 Specifications Application 5 25 SATA optical disc drive e Drive length 16 5cm 18 5cm Interface Ports eSATA e USB 2 0 High Speed Data Transfer eSATA up to 3 0Gbps 300MB s e USB 2 0 up to 480Mbps 60MB s e USB 1 1 up to 12Mbps 1 5MB s System Requirements eSATA Windows XP Vista PC USB 2 0 Windows XP Vista e eSATA Plug amp Play support for host controller System Requirements eSATA Mac OS 10 4 or higher Mac USB 2 0 Mac OS 10 2 or higher e eSATA Plug amp Play support for host controller Operating Environment Temperature 5 C 40 C e Humidity 10 RH 80 RH Storage Environment Temperature 20 C 70 C e Humidity 5 RH 90 RH Power Supply Input AC 100 240V e Output DC 12V 2A Enclosure Size 23 6cm x 17cm x 6cm Note Available interfaces and data transfer speeds depend on the model 5
Download Pdf Manuals
Related Search