Viper Fang 15 inch Automatic Scrubber Owner`s
Contents
1. 990008 AT ATI 10406 RED 1 BLACK Battery charging Charge the batteries see Maintenance section MACHINE SET UP Pre operation checks Sweep or dust mop the surface to be cleaned Check that squeegee is properly installed Lower the squeegee 33 with the lever 26 Ensure batteries are fully charged see Battery Charging section Check that brush is properly installed oa GQ Brush Pad driver installation and disassembly NOTE Only install manually If automatically installed it will wear brush hub Make sure that the tanks are empty before removing the brush 1 Turn off the machine 2 Lay down the machine in the position shown in figure 2 Pull up lift lever 26 to raise the squeegee 33 USER MANUAL 3 Mount the brush or pad driver onto the drive wheel hub and then rotate counterclockwise until it locks as indicated in figures 4 remove the brush pad rotate the brush pad clockwise until it is released from drive hub WARNING Do not turn on the machine in this position as below In case of brush pad come out or cause injury Squeegee installation 1 Turn off the machine 47 2 Pull down the squeegee lift lever 26 to put down the squeegee in the working position 3 Lay down the machine in this position as shown in figure2 4 Loosen the two knobs 55 on the squeegee and slide the squeegee into the slots on the squeegee brackets T2. Brush cleaning Clean tank vacuum screen amp check top cover gasket Squeegee blade check and replacement Solution filter cleaning Drain hose filter cleaning Screw and nut tightening check 1 Lubricate rotary parts 1 Check brush motor carbon brushes 2 Check vacuum motor carbon brushes 2 1 After the first 8 working hours 2 This maintenance procedure must be performed by an authorized Service Center BATTERY CHARGING O NOTE Charge the batteries when the yellow or red indicator 51 or at the end of every work cycle A CAUTION Proper battery care will extend battery life AN CAUTION If the machine is not equipped with on board battery charger choose an external battery charger suitable for the type of batteries installed AN WARNING Please use Viper approved charger to charge the batteries AN WARNING USER MANUAL Pay careful attention when charging WET batteries as battery fluid could leak Battery fluid is highly corrosive If fluid comes in contact with skin or eyes rinse thoroughly with water and consult a physician Place charger and machine in a well ventilated area Turn machine off 47 Remove the recovery tank 2 exposing battery compartment Plug the charging cable to the grounded wall outlet 100v 240v Connect the charging cable to the machine socket 5 The charging light 30 indicates the batter
3. 12V STORAGE BATTERY S 5 CHARGER gt 5 SK AD AD ST ST 12V STORAGE BATTERY DA DA CK 5V 5V CHARGE K 2 lt 500 5 GND TRIGGER SWITCH 12AWG BLACK BRUSH MOTOR VACUUM MOTOR EV 1 14AWG BLACK 18 14AWG RED 4 BRUSH MOTOR 2 14AWG BLACK N 2 MMAWGRED N VACUUM MOTOR WATER VALVE www usviper com
4. bucket 2 Clean and Rinse the recovery tank with clean water after every use 3 Re place the recovery tank on the machine and turn the latch 17 to lock the tank in place MACHINE OPERATION Set the handle to a comfortable height by pressing level 25 Lower the squeegee 33 onto floor by pulling down the lift handle 26 Turn on the main power switch 47 Turn on the brush motor switch 48 and the solution switch 50 Turn on the vacuum motor switch 49 If necessary adjust the water flow by manually turning the ball valve 31 Pull one or both operating triggers 24 The brush will spin amp solution will begin to flow Push the machine forward to start cleaning O WD NOTE O If the battery indicator light 51 is green the machine can be used If it is yellow or red the batteries must be charged USER MANUAL CAUTION Before lifting the brush turn off the main power switch 47 CAUTION If the control panel 46 lights flash simultaneously this indicates the machine is overloaded Please turn off all the switches on the control panel 46 to reset the machine If problem persists contact authorized service provider AN CAUTION Operating machine with discharged batteries may cause harm to the batteries or to the machine AFTER EACH USE After scrubbing please proceed with below actions before storing the machine 1 Remove the brush pad holder 2 Empty the tanks as shown i
5. M5 VF89337 PRESSURE ADJUSTMENT PLATE 1 15 PART LIST BRUSH SKIRT amp BRUSH BRUSH SKIRT amp BRUSH FANG 15B SHAFT SCREW ST4X10 ELBOW BRUSH ASSEMBLY PAD DRIVER ASSEMBLY 17 PART LIST HANDLE CONTROL ASSEMBLY 18 HANDLE ASSY FANG 15B VF89615 LEFT 10 VF866 RIGHT 11 12 13 14 15 16 17 18 19 20 21 22 23 vVvrFesot7 CONTROL HOUSING______________ 1 19 PART LIST RECOVERY TANK ASSEMBLY RECOVERY TANK FANG 15B rn 4 VFe9702 1 RUBBER BUSHING TANK 5 VF89702 2 RUBBER BUSHING TANK GREY DD 6 Ves97o3 SQUEEGEE SUCTION 17171 7 Vee97o7 KM SQUEEGEE e 69716 JKIT RECOVERVTANKCOVETTI J Vre9ri2 COVER RUBBER 11 12 Vre97o9 GUIDE BASE PLUG VACUUM vrem PLUG BASE O L Ca vena veno prue COVER O L r 16 VFeeros 7 r ie Vre97os _ COVER VAQUOM HT 3477 SOREW stax O O Oo o oa C vrema SEAL ID 1 Ca wees SOREW sexe L e 22 13664 DAXD12X1 0 STAINLESS 2 89715 LATCH TANKLID 2 24 689713 _ 21 PART LIST SQUEEGEE ASSEMBLY 22 SQUEEGEE ASSY FANG 15B VF89501 SQUEEGEE BRACKET VF89502 SQUEEGEE
6. ATE VF89801 BRUSH ASSEMBLY VF89804 PAD DRIVER VF85102 SMALL CLAMP VF89055 RUBBER PLUG CHARGER INSERT VF89020 BATTERY 2 12V 35Ah VF89036 POWER WIRE VF89021 KIT BATTERY CONNECT LINE VA13473 PH SCREW M4X16 VF89700 KIT RECOVERY TANK VF85141 BIG CLAMP VA13472 PH SCREW M4X8 2 11 PART LIST SOLUTION TANK ASSEMBLY SOLUTION TANK ASSY FANG 15B Description vemo abaan C 10 Vees302 RUBBER f 5096994000 SOLUTION TAPA 89112 CABLE 14200 PH 714 Vrena SEAT NIET FRESHWATERTANK 1 15 Verena FILTER INLET FRESH WATER TANK e VFISASTI PH SCREW maa O O o Ta e veno JKITSOLUTIONTANKTI O vre A Vres202 DRIVE Taf vrases _ WASHERMWAVE O T J vras SNAP SPRING 200 KM WHEEL AXLE A lt 13 PART LIST BRUSH DECK ASSEMBLY 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 BRUSH DECK ASSY FANG 15B Description VF89301 VF89302 VF89303 PLATE MOTOR MOUNT BRUSH MOTOR ASSEMBLY SCREW M6X14 VF89304 BOLT DIRVE BELT VF89305 O RING BIG VF89306 VF89307 SCREW M6X25 NUT NYLON INSERT M6 C VF13614 WASHER 06 T 20058 BOLT M6X25 HEX Vresste SPRING 17 GT13084 SCREW M6X20 VF89308 SILENCER SPONGE VV13633 NUT
7. BLADE FRONT VF89502 PU SQUEEGEE BLADE FRONT PU OPTIONAL 89503 SQUEEGEE BLADE REAR VF89503 PU SQUEEGEE BLADE REAR PU OPTIONAL 23 PART LIST ELECTRICAL 24 ELECTRICAL PARTS FANG 15B E a VF89026 MOTOR WIRE 2 VF89022 MAIN POWER WIRE VFseo2t BATTERY CONNECT WIRE vres Om mE O oS s VFee024 CHARGERINPUTWRE _vFesez0___ KI 4LEG SWITCH T f VF090253 COMMUNICATION WIRE fd 25 TROUBLESHOOTING USER MANUAL Trouble Possible Cause Remedy The machine does not work indicator light 51 do not turns on The battery connector is disconnected Connect The batteries are completely discharged Charge the batteries The power line disconnected from the power Connect The machine does not work indicator light 51 display red The batteries are discharged Charge the batteries Brush motor does not work brush indicator light 52 does not turn on The PCB or key board is broken Change the PCB or key board Brush motor does not work brush indicator light 52 flashes The deck motor is overloaded Use less aggressive brushes suitable for the floor to be cleaned Obstruction preventing the brush from rotating Clean the brush hub Vacuum system motor does not work vacuum motor indicator light 53 does not turn on The PCB or key board
8. If necessary replace the pad driver RECOVERY TANK MAINTENANCE AN CAUTION It is advisable to wear protective gloves when cleaning the tank and vacuum suction assembly because there may be sharp debris 1 BD Move the machine to the appointed draining area Turn off the main switch 47 Remove the recovery tank 2 clean and rinse both solution recovery tank and drain out Remove vacuum gasket amp filter Clean and re install Check the recovery tank lid gasket and the vacuum rubber connector 18 forwear Replace if necessary O NOTE The gasket ring of recovery tank and the rubber connector between two tanks create vacuum in the tank If necessary replace them Control Panel 46 Control panel 47 Main switch 48 Brush motor switch 49 Vacuum motor switch 50 Solution switch TECHINICAL DATA USER MANUAL 51 Battery indicator 52 Brush motor indicator 53 Vacuum motor indicator 54 Solution indicator MODEL FANG15B Machine length width height 770x500x550MM Solution tank capacity 15L Recovery tank capacity 15L Wheel diameter 254MM Brush motor 24V 250W Vacuum motor 24V 250W Solenoid valve 24V Maximum gradient when working 2 Sound level 70dBA Standard Batteries Dry 2X 12V 24V 33Ah Batteries size 196 x 130 x 175mm Power cable length N A Cleaning productivity 750m hour Squeegee width 490mm Brush diamet
9. VIPER 15 Inch AUTOMATIC SCRUBBER OWNERS MANUAL IMPORTANT READ OWNERS MANUAL CAREFULLY Please fill out amp return your warranty card www usviper com MODEL FANG15B SERIAL VIPER exceptional P O BOX 104 u HAMILTON MI 49419 866 418 4737 VF89027 US REV O1 866 41 VIPER 2013 07 17 USER MANUAL SAFETY PRECAUTIONS This machine is intended for commercial use It is constructed for use in an indoor environment and is not intended for any other use Use only with recommended accessories All operators shall read understand and exercise the following safety precautions 1 DO NOT OPERATE MACHINE Unless trained and authorized Unless you have read and understand the operators manual In flammable or explosive areas If not in proper operating condition In outdoor areas 2 BEFORE OPERATING MACHINE Make sure all safety devices are in place and operate properly 3 WHEN USING MACHINE Go slow on inclines and slippery surfaces Follow all safety guidelines Be very careful when using the machine in reverse Report and fix any damage to machine prior to operating it 4 BEFORE LEAVING OR SERVICING MACHINE Stop machine on level ground Turn machine off 5 WHEN SERVICING MACHINE Read operators manual thoroughly prior to operating or servicing this machine Use manufacturer supplied or approved replacement parts Secure machine with wheel blocks prior to jacking the machine up Use approved jack or hois
10. er 380mm Brush rpm 150rpm Charger Input 110 224Vac 50 60HZ Output 24Vdc 5A Machine net weight 60kg Machine weight with charger and package CARE Carton spec 780x415x590MM PART LIST COMPLETE ASSEMBLY 10 14 ojoj al aja op 56 57 58 59 61 COMPLETE MACHINE FANG15B Description VF89100 VF89018 VF89200 VF14251 VF13514A VF14516 VF89300 VF85698 VF89030 VF14258 VF14503 VF89400 VV13664 VF13491 VF89500 VF89029 VF85420 VF89600 VF89001 VF89002 VF89003 VV6022081 VV20290 KIT SOLUTION TANK LABEL SOLUTION TANK KIT AXLE WHEEL BOLT M8X30 HEX HEAD WASHER D8X1XD16 5 NUT NYLON INSERT M8 KIT MOTOR MOUNTING PLATE HEX SOCKET SCREW M8X55 BUSHING HEX SOCKET SCREW M8X40 NUT M8 KIT SKIRT ASSEMBLY WASHER D4X1XD8 PH SCREW M4X12 KIT SQUEEGEE HOSE CONNECT SQUEEGEE THUMB SCREW KIT HANDLE ASSEMBLY HANDLE BLOCK LEFT HANDLE BLOCK RIGHT CIRCUIT BOX HEX SOCKET SCREW M6X15 WASHER LOCK 66 VF13614 WASHER 6 GT13027 PH SCREW M5X45 VA13482 VF89004 VF89005 VF89023 VF89025 1 VF89006 VF14901 VF89034 VF89052 VF89037 VF89035 VF89016 VF89012 VF89017 VF89007 VF89008 VV20509 PH SCREW M5X10 VF89010 VF89011 AXLE SQUEEGEE LIFT CABLE VF89009 ROTATE AXLE SQUEEGEE LIFT CABLE VF89056 SOLENOID VALVE 24V VF14514 NUT NYLON INSERT M5 VF89033 HOSE VF89013 PIPE SI D4XD8 0 7M VF89014 PIPE SI D6XD10 0 4M VF89015 PL
11. ies are charging A green light indicates battery charging is completed 6 Upon the completion of charging first unplug the charging cable from the wall outlet and then disconnect from machine 7 Replace the recovery tank O NOTE For further information about the operation of the battery charger 29 see the charger section Pe SQUEEGEE CLEANING O NOTE For optimal performance the squeegee blades must be clean dry and undamaged AN CAUTION It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris SQUEEGEE BLADE CHECK AND REPLACEMENT Take off the squeegee as shown in the previously Check the edges of the front amp rear blades for cracks If necessary replace with new blades Unscrew six the thumb nuts 37 to remove the blades Check the front amp rear blades for cuts and tears If damage is found you can flip the blades once amp re install If already flipped please replace with new blades 5 Install the squeegee in the reverse order of removal Fr DN USER MANUAL BRUSH PAD DRIVER CLEANING AN CAUTION It is advisable to wear protective gloves when cleaning the brush pad because there may be sharp debris 1 2 3 4 Remove the brush pad as shown in Machine Use section Clean and wash the brush pad with water and detergent Check the brush bristles for integrity and wear If necessary replace the brush Check the pad for wear
12. ighten the knobs securely unscrew the knobs if to remove 6 Toreplace the front rear squeegee 56 57 unscrew the thumb knobs 37 amp TA Fi ALL 55 97 USER MANUAL Solution tank filling NOTE The machine can be filled with a hose or bucket Do not remove the Solution filter 21 while filling 1 Fill water into solution tank 3 from the inlet 20 through hose or bucket 2 Do not overfill the solution tank It is best to leave a an inch from the top edge 3 The water temperature must not exceed 40 C DM CAUTION1 Use only low foam and non flammable detergents intended for automatic scrubber applications Solution tank draining NOTE O Solution tank should be drained and cleaned after each scrubber operation is completed 1 Unscrew the drain cap 22 on the bottom of solution tank The solution water will flow freely into a bucket or floor drain 2 Rinse the solution tank with clean water after every use This will help prevent chemical buildup and clogging of the solution lid 3 Replace the drain cap 22 Recovery tank draining NOTE O Recovery tank should be drained and cleaned after each scrubber operation is completed 1 Turn the latch 17 on the recovery tank Remove the recovery tank from machine by grasping two grooves of tank and pulling up Open the lid 1 and overturn the recovery tank to drain the dirty water into a container or unscrew the drain cap 22 to let water drain into a
13. is broken Change the PCB or key board Vacuum system motor does not work brush indicator lights 53 flash The vacuum motor is overloaded Check the vacuum motor Insufficient vacuuming water pickup The recovery tank is full Empty the recovery tank The hose is disconnected from the squeegee Re connect Vacuum assembly is clogged Clean or check The squeegee is dirty or the squeegee blades are worn or damaged Clean and check the squeegee The recovery tank do not latched closed Lock the latch 17 The tank cover is not properly closed or the gasket is damaged Close the cover properly or replace the gasket The solution flow is insufficient The solution filter is dirty Clean the filter The solution is empty Refill solution tank Solution flow control valve 31 is clogged Clean the valve The solution is dirty Clean the solution The squeegee leaves marks on the floo There is debris under the squeegee blades Remove the debris The squeegee blades are worn chipped or torn Replace the blades 26 USER MANUAL 12AWG BLACK 12ANG RED vec _ _ c BANG BLACK E 5 18AWG RED lt lt COMMUNICATION LINE FIS CONTROL BORAD lt L
14. n the previous paragraph 3 Perform the daily maintenance procedures see Maintenance section 4 Store the machine in a clean and dry place with the brush pad holder and the squeegee up 5 If storing in an area that may reach freezing temperatures be sure to drain all fluids from the machine prior to storage Any damage caused by freezing will void the warranty MACHINE STORAGE If the machine is not going to be used for more than 30 days please proceed with below actions 1 Perform the procedures shown in After Each Use section above 2 Disconnect the battery connector MAINTENANCE The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance The following chart provides the scheduled maintenance The intervals shown may vary according to individual working conditions AN WARNING Maintenance procedures must be performed with the machine switched off and the batteries battery charger cable disconnected Moreover carefully read the instruction in the Safety chapter All maintenance procedures must be performed by qualified personnel or by an authorized Service Center This Manual describes only the most common maintenance procedures For additional maintenance procedures contact your local Service Center SCHEDULED MAINTENANCE TABLE USER MANUAL Procedure After each use Weekly Every six months Annually Battery charging Squeegee cleaning
15. t to safely elevate the machine Disconnect batteries prior to working on machine Wear gloves when handling batteries or battery cables Avoid any contact with battery acid Avoid moving parts do not wear loose fitting clothing while servicing machine AN WARNING Batteries emit hydrogen gas Explosion or fire can result from hydrogen gas Keep Sparks and open flames away Keep battery compartment open when charging WARNING Flammable materials can cause an explosion or fire Do not use flammable materials in tanks DM WARNING Flammable materials or reactive metals can cause explosion or fire Do not pick up USER MANUAL MACHINE SET UP amp INSTALLATION UNCRATING MACHINE Be sure and check packing carton for any damage Immediately report any damage to carrier Check contents of package to ensure that the following items are included Machine Batteries x2 Squeegee assembly Owners Manual Electric Battery Charger Manual Cif equipped Connecting wire for battery and charger if equipped Brush N BD BATTERY DISASSMBLY AND INSTALLATION Switch off the main switch 47 Remove the recovery tank 2 Remove the bolt from batteries 16 Remove or change batteries Install the batteries on the machine according to the diagram below Install the recovery tank WARNING Do not connect to or to when disassembly or install the batteries It is very dangerous gt gt 104WG BLACK
Download Pdf Manuals
Related Search