RRC-250 & RRR-250
Contents
1. 3 7149 in USA support labelmateusa com www labelmateusa com LABELMATE USA uc RRC 250 amp RRR 250 RRC Reel to Reel Counter RRR Reel to Reel Rewinder Variable Speed Control with Direct By Pass for Full Speed 6 Digit Digital Pre set Counter Up to 250 mm 10 Roll Diameter RRC 250 Reel to Reel Counter Remove all parts from shipping container and verify contents Package Contents e User Manual this document e RRC 250 Unit e Power Supply Module with Power Cord Retain the Shipping Container and Packaging for Storage and Transport e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e WARNING This product is for indoor use only Not for use in wet locations Unplug unit before removing waste material or performing any cleaning or maintenance services A Plug the Power Supply into a suitable AC Power Main Outlet Plug the Power Supply Output Cable to the Power Jack on the Rear Panel of the RR 250 Place the Power Switch on the rear of the RR 250 to the ON position Observe that you have Power to the unit A RR 250 SET UP RRC 250 The Counter is pre programmed as a Preset Count Up Counter If you would like to use the preset function input the desired number of labels into the Counter Module with the Push Buttons on the Counter If you do not wish to use preset count set the value on the Counter Module to 100000 THE RRC WILL NOT WORK IF THERE IS NOT A PRESET COUN2. Product Limited Warranty Labelmate USA warrants to the original end user customer that Labelmate USA products will be free from defects in materials and workmanship for the duration described herein below Labelmate USA s Limited Warranty covers only those defects that arise as a result of normal use of the products and does not cover any other problems including those that arise as a result of i improper maintenance or modification ii parts or supplies not provided or supported by Labelmate USA iii operation outside the products specifications or iv unauthorized repair modification or misuse Use of any unauthorized accessory or attachment will void coverage The Warranty period for all products commences the date of shipment from Labelmate USA and accrues to the original end user customer Warranty coverage is non transferable and terminates immediately upon rental resale or any other change in ownership Original purchase documentation should be retained for Warranty coverage verification In the event Labelmate USA substantiates during the applicable Warranty period a defect in any product which is covered by Labelmate USA s Warranty Labelmate USA shall repair or replace the product at Labelmate USA s option Labelmate USA retains sole discretion to determine whether or not a product is defective In no event shall Labelmate USA have any obligation to repair or replace until the customer returns the defective product to Labe
3. T ENTERED INTO THE COUNTER MODULE RR 250 OPERATION Place the STOP RUN Switch in the STOP position Place your roll of labels on the Unwind REEL at the left of the RR 250 The Rewind REEL on the right rotates in a counter clockwise direction Note that your RR 250 can be Wind In or Wind Out depending on which way you place the Label Roll on the Roll Holder right side up or upside down Place an empty 3 label Core not included on the Rewind REEL Thread the material through the RR 250 as shown on the WEB PATH Label on the unit Adjust the Plastic Rings on the Paper Guide Rollers to slightly touch the top edge of the material Place STOP RUN Switch to the RUN position Slowly turn up the SPEED Knob making sure you are now Counting the material that is passing through the Sensor IF THE COUNTER IS NOT COUNTING THE MATERIAL YOU MAY HAVE TO ADJUST THE PHOTOCELL see next section of this manual There is a Speed Adjust Switch on the left hand side of the unit that will allow you to run the RR 250 at FULL Speed without having to adjust the SPEED Knob on the top of the unit Once the RR 250 has Counted all the material on the given roll and there is nothing in the Sensor the unit will shut itself OFF You must reset the Counter and the Switch and have material in the Sensor for the Counter to Power On again THE RR 250 WILL NOT WORK IF THERE IS NO MATERIAL IN THE SENSOR PHOTOCELL ADJUSTMENT T
4. he sensitivity of the Photocell that detects the Labels and triggers the Counter Display should be calibrated for the labels being Counted Here s how Place the RRC STOP RUN Switch in the STOP Position Place a Label Liner ONLY no label in the Label Sensor Gap Using a small flat bladed screwdriver carefully adjust the Photocell Adjust Control on the left hand side of the unit until the green Photocell Adjust LED illuminates OR Adjust Photocell Adjust control for 3 to 5 VDC at the Photocell Test Jack 3 5 mm Plug MAINTENANCE The RR 250 requires no maintenance Please keep unit sensor and rollers clean of adhesive build up RRR 250 Reel to Reel Rewinder
5. lmate USA The customer assumes any and all responsibility and liability associated with transportation of products for service under this Warranty WARRANTY PERIOD PRODUCTS COVERED CAT and Mini CAT Label Rewinders 9 Years UCAT Label Unwinders Label Counters Excluding Counter Displays and Encoders Label Dispensers Excluding Counter Displays Label Slitters Wechanical Parts Only and excluding Counter 3 Years Displays Reel to Reel Machines Excluding Counter Displays and En coders Print Mechanisms Excluding Counter Displays and Encoders Quick Chucks Power Supplies AC DC Adaptors and Transformers Counter Displays Encoders Any other products or parts not specified herein 180 Days Out of Warranty Repairs In the event your product requires service or you have questions regarding Warranty coverage please call toll free 877 833 7149 inside the United States or 1 702 435 8535 outside the United States 1 Year LABELMATE MAKES NO OTHER WARRANTY OF ANY KIND WHETHER EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND OR FITNESS FOR A PARTICULAR PURPOSE NO OTHER PERSON AGENT DEALER OR RESELLER IS AUTHORIZED TO GIVE ANY WARRANTIES ON BEHALF OF LABELMATE ANY OBLIGATION TO WARRANTY OTHER THAN THAT SPECIFICALLY ADDRESSED HEREIN IS EXPRESSLY DISCLAIMED LABELIWATE USA uc 12A Sunset Way Henderson NV 89014 USA 702 435 8535 FAX 702 435 8536 Toll Free 877 83
Download Pdf Manuals
Related Search