USER`S MANUAL - IPM Ingenieros
Contents
1. a Follow the application software in use as well as the computer manufacturer s instructions for saving data and turning off the computer D After a blackout keep the breaker MCCB1 ON for at least 10 hours to ensure the batteries are fully recharged 6 5 Maintenance amp Service Inverter to Maintenance Bypass 1 Disconnect load power supply at normal loading state Press power OFF button on the front panel check the UPS me I i is at mains power condition LCD Display MODE BY BEE st Bypass 15 6 OPERACION 3 Screw off the Cover of Maintenance Bypass Switch which is located at the rear side The UPS will shut off AUTOMATICALLY Turn the Maintenance Bypass Switch to BYPASS state Put ON the cover of Maintenance Bypass Switch for Maintenance Service Otherwise the UPS will NOT work Turn OFF the MCCB1 Input Circuit Breaker amp MCCB2 Battery Circuit Breaker Do maintenance and service 6 6 Maintenance amp Service 6 OPERACION Maintenance Bypass to Inverter When the Maintenance and Service has been done please take the following procedures 1 Turn ON the MCCB1 Input 2 Circuit Breaker amp MCCB2 Battery Circuit Breaker Press power OFF button on the front panel check the UPS is at mains power condition LCD Display Take OFF the cover of Maintenance Byp2. DISPLAY Q S Y MODE INV INVERTER mode MODE BY BYPASS mode CD ES e s 2 LINE AC INPUT Red The Indicator is ON when the incoming Fa a D LY D utility power is available 3 3 BYPASS Amber The indicator is ON when the UPS output o gt J power is supplied from the incoming power source e Sr A LOAD Red When the load is over 100W the indicator would sl p Ne H illuminate When it reaches over 100 load UPS would emit an lag lt audible alarm sound continuously for 20seconds T S Sg 5 INVERTER FAULT Red The indicator is ON when UPS is in faulty condition and would emit continuous audible alarm sound KF x 7 Note When the unit is fault please refer to the paragraph 4 Table and figures 6 BATTERY Red The indicator is ON under these situations a When AC mains abnormal Inverter runs from battery s power b Battery discharge reach to a low level and automatically UPS LNdLNO OV would emit a quick alarm reminding that battery s energy will be soon exhausted 3 PANEL DESCRIPTIONS 4 UNIT REAR VIEW 7 INVERTER Red The indicator is ON when the UPS Inverter is operating properly 8 ALARM RESET Press it to stop buzzer alarm 9 POWER ON Push Button Press it to start the UPS 10 POWER OFF Push Button Press it to shut down the UPS If the AC mains exist the unit will transfer itself to BYPASS output 11 MENU AUTO Push Button When press once at a time it will display the following sequenc
3. assignment and description of DB 9 Connector Bypass Active Fe PINI Close Bypass Active Open UPS ON Ss ee PIN2 Close Utility Failure N O Ground PIN3 Close Utility Failure N C Battery Low Samea PIN4 Ground UPS Failure PINS Close Battery Low o PIN6 Auto Cut Off D ee PIN7 Auto Cut Off GE PIN8 Close Summary Alarm PINO Close UPS Failure 2 RS 232 Interface Baud Rate 2400bp Parity Bit The following is the pin assignment and description of RS 232 Connector PIN DESCRIPTION UO RS232 Rx INPUT BR 6 LS RS232 Tx OUTPUT INPUT 21 10 PRODUCT SPECIFICATION ARton Capacity KVA Voltage lt 1 85V 270V 230V 60Hz 5 Phase 10 2W G as client demand lt CO Q C2 D hase Voltage 230V 2 1 2W G as client demand rest e ort lt CO Q C2 D O P 0 8 to 1 lagging P Voltage Regulation 1 at liner load 60Hz 0 5Hz Waveform Distortion Pure sinewave less than 3 at full load O lt Sp Se D Q O Ou D O as a 5 ey LA 5 G 5 ep Overload Capacity 100 124 continuous 1 25 30secs 135 1 sec gt 80 at battery fully charge rechargeable sealed maintenance free Battery Around 5min at full load 4 8 hours 90 after fully discharge No break UPS to Bypass 6 zE No break nput Output attery Voltage Frequency Indicator LCP Display Output Load Operation Tempera
4. e e AR Tronic The art of electronics INDUSTRIAL GRADE ON LINE UPS With Maintenance Bypass Switch MODEL ARTon 10 10KVA USER S MANUAL Please read this manual thoroughly prior Installation Operation Cover CONTENTS Contents Page 1 SAFETY INSTRUC TIONS e eeesekegeegeeeettege eseeegereggedeggegsgeeug Da DIN TRODUCTION D P 5 2 PANEL DISCRIP TION o egecee eege dee Sue P 7 A IESELEN Do ES INSTALLA TION E P 10 BORE RATION E P 14 7 TROUBLE SHOOTING GUIDE P 18 8 CUSTOMER SERVICE ceceterettrer eect reretereseesnseseseseseeseeeeneeegees P 19 9 COMMUNICATION PORT Scettt tr ter sr REENEN EEN EREE RENE REENEN D oi 10 PRODUCT SPECIFICATION een D 99 11 WARRANT Y ssss s ssssssnnsnnnnnnnnnnnsnnennnnnunnnnnnnnnnnnnnnnnnn D 23 Bottom 0 1 1 SAFETY INSTRUCTION 1 1 1 2 1 3 Transport Please transport the UPS system only in the original packaging to protect against shock and impact Set up Condensation may occur if the UPS system is moved directly from a cold to a warm environment The UPS system must be absolutely dry before being installed Please allow an acclimatization time of at least two hours Do not install the UPS system near water or in damp environments Do not install the UPS system where it would be exposed to direct sunlight or near heat Do not block off ventilation openings in the UPS system s housing Installation Do not connect appliances or items of equipmen
5. and UPS use a Digital Multi meter DVM to verify if the input and notify the carrier and dealer immediately if there is any damage EECHER or lacking of some parts 5 If comply connect the input and output wires to the corresponding input and output terminals according to the 5 2 Notes for Installation following diagram 1 The UPS must be installed in a location with good ventilation DOE STE EADIE OUI MWA GH EE output terminals are connected tightly far away from water inflammable gas and corrosive agents 7 o 6 Switch on MCCB1 and MCCB2 The indicators of LINE 2 Ensure the air vents on the front and rear of the UPS are not BYPASS INVERTER and FAULT will all light on If AC blocked It is recommended to retain 10cm from the wall mains exist the fans on the rear panel operate with AC power 3 Condensation to water drops may occur if the UPS is outputs BYPASS unpacked in a very low temperature environment In this case 7 Press ON button on the front panel the fans on the front panel rotate the UPS start to detect itself automatically right away 25 seconds later BYPASS extinguishes and INVERTER remains illuminating The protective earth ground wire refers to the wire connection 4 Put the unit in a plain between the equipment which consumes electric equipment and the ground wire The wire diameter protective earth ground wire should be at least as above mentioned for eac
6. ass Switch Change the indicator to INV state Put ON the cover The UPS have no function if the cover doesn t put on Press Power ON button on the front panel Repeat Startup Procedure 7 TROUBLE SHOOTING GUIDE The Meaning of Indicators and Alarm Indicators and Alarm De Status Recommend te me on ran ear comin Soon ONT ON ON OFF OFF NO OFF ON Flashing OFF OFF Every e gege mains eme your 4 sec failure UPS is software and charging bat les in use Mains button on the front panel ON or ON OFF Conti UPS is at Remove condition load OFF ON Flashing OFF ON OFF Every Normal Close your 1 sec battery will files and discharge software in completely use Conti The output Remove short nuous circuit is circuit start shorted the UPS again Conti UPS works on Warming only nuous BYPASS not affect UPS state while the operation input voltage is over 270V Conti UPS interior is UPS will nuous too hot as it transfer to has been BYPASS working on mode BYPASS or INV fora period of time ON OFF Conti UPS works on Call for nuous INV or service if UPS BYPASS works on INV Whereas the UPS work on BY PASS is because the AC voltage is too high Flashing 18 8 CUSTOMER SERVICE There are no serviceable components inside Do NOT open the cover or attempt to service the unit High voltage may remain even wh
7. e of messages a Input Voltage Frequency b c Current Percent of Load d Output Voltage Frequency Battery Voltage UPS Operating Temperature f presses for 3 seconds it will display above messages in an automatic cycle 1 Maintenance Bypass Switch For Maintenance Service use 2 MCCB1 AC Input Circuit Breaker The MCCB1 should be switched ON to provide the utility power of the UPS 3 MCCB2 Battery Circuit Breaker The MCCB2 should be switched ON to control the DC power of the UPS Output Sockets Communication Port RS232 option DB9 Ventilation Fan oo Se Output Fuse 5 INSTALLATION 5 INSTALLATION The system may be installed and wired only by qualified electricians in 5 3 Installation amp Starting accordance with applicable safety regulations 1 Installation and wiring must be performed in accordance with the local electric code and the following instructions by 5 1 Unpacking amp Inspection professional personnel 1 Unpack the package and check the package contents The 2 For safety consideration please turn off the mains power shipping package contains switch before installation AUPS 3 Open the terminal block cover located on the rear panel of the A User Manual UPS please refer to the appearance diagram 2 Inspect the appearance of the UPS to see if there is any 4 Check the power requirement label at the rear panel of the damage during transportation Do not turn on the unit
8. ed to answer the following question before calling for service 1 Is the AC supply power rating correct 2 Is the power cord connection loose 3 Turn ON the Main Switch again Does the UPS return to normal operation 4 Did a power failure occur just after or before the malfunction was noted 5 What is the status of the indicator at the time of the malfunction And on restarting the UPS 6 Where any changes made to the UPS or the critical device attached to the unit 7 Did overload condition happen If so remove non critical loads from the unit and go through the restart procedure 8 In addition check the fuse or breaker on the rear panel Is the fuse busted or the circuit protector tripped If the UPS fails to operate normally after carrying out these checks contact our local service representative Please note down the following information before you call for service a Model number amp serial number b Date of problem c Full descriptions of problem 20 9 COMMUNICATION PORTS Power management software and interface kits can be used with this UPS Use only kits supplied or approved by the manufacturer If used connect the interface cable to the 9 pin computer interface port on the back panel of the UPS Secure the connector s screws to complete the connection Note Computer interface connection is optional The UPS works properly without it 1 DB 9 Interface option The following is the pin
9. en the unit is shutdown Unauthorized service will void the warranty and may cause serious injury 8 1 Maintenance The unit is designed for easy maintenance Only a little customer maintenance is required The following works will keep ensure trouble free operation 1 Vacuum the dust from the ventilation in take on the front panel 2 Wipe the cover with a damp cloth 3 Periodically switch off the AC supply to the UPS to check the operation of the UPS and the battery condition Before testing be sure to save any data files in use 4 Cautions a Follow the user s manual to operate it b After power failure Keep power applied continuously to the UPS for at least 12 hours to ensure that the batteries are fully recharged c When batteries discharge completely the UPS will shutdown by itself automatically to protect the batteries from over discharge When the AC power recovers the UPS will reset automatically 5 Storage Instructions a Leave the UPS plugged in for 24hours prior to storage b Store the UPS in a cool dry environment Below 80 F 27 C c Remove from storage and repeat step 1 every 90days d Disconnect the power cord from the AC supply socket during storage 19 8 CUSTOMER SERVICE 8 2 Trouble Shooting Due to the unique design the unit must be serviced by authorized person only If the UPS fails to operate properly turn off the power first and review the following check list Be prepar
10. h model and green wire or green wire with yellow ribbon wire is used it is necessary to wait until the UPS is fully dried inside out before proceeding installation and use Otherwise there are hazards of electric shock 8 kb 10 11 5 INSTALACION 5 INSTALACION 9 To connect the load with the UPS please turn off all the loads first then perform the connection and finally turn on the loads 5 4 Installation of UPS Enclosure NEMA 3R one by one 10 No matter the UPS is connected to the mains power or not the output of the UPS may have electricity The parts inside the unit may still have hazardous voltage after turning off the UPS To make the UPS have no output power off the UPS and t hen disconnect the utility power supply 11 The UPS now is ready for working connecting the critical equipment to the output terminal blocks NOTE a Keep power continuously for 12 hours at the first start to ensure the battery fully charged It is recommended to press OFF button on the front panel but open the circuit breaker MCCB1 during charging b High DC voltage remains not touch the external battery terminals c Do not short circuit wires at the external battery terminals block d Make sure the battery polarity is correct 12 13 6 OPERATION 6 1 Check Prior to Start UP 1 Ensure the UPS is in a suitable positioning 2 Check input cord is secured 3 Make sure the load is disconnected or in the OFF p
11. nd telephone number should be included This warranty will be considered void if the unit has suffered any obvious physical damage or alteration either internally or externally and does not cover damage arising from improper use such as plugging The unit into an unsuitable power sources attempts to operate products with excessive power consumption requirements or use in unsuitable environments This is the only warranty that the company makes No other warranties express or imply including warranties of merchantability and fitness for a particular purpose Repair and replacement are your sole remedies and the company shall not be liable for damages whether direct incidental special or consequential even though caused by negligence or other fault
12. osition 4 Check if input voltage meets the UPS rating required 6 2 Start up Procedure 1 Turn on the circuit breaker 2 Push the ON switch on the front panel Blue color switch 3 Turn on the power breaker of your critical equipment 6 3 Turn OFF Procedure 1 Turn off all the power breakers on your critical equipment which are connected to the UPS 2 Press the ON OFF buttons on the front panel 3 Turn off the NFBs MCCB1 amp MCCB2 on the rear panel NOTE a The NFB can be kept in ON position to charge the batteries when the line input is normal b For daily TURN ON TURN OFF operation it is recommended to keep the breaker ON to ensure proper battery operation WARNING If the breaker is at ON position the line power will be supplied to outlets Do not insert objects other than equipment power cords into the outlets 14 6 OPERATION 6 4 Working 1 When mains power is interrupted the UPS will convert the built in battery source to protect your critical load from loss of data or damage 2 Battery back up time is around 5 minutes for full load and can be extended by removing non critical loads 3 After mains power black out the audible alarm will sound every 4 seconds to show that output is backed up by battery source 4 When audible alarm speeds up and sounds every 1 second data should be saved and all loads should be shut down at ONCE NOTE
13. pability capacitor such as BUS capacitors 1 SAFETY INSTRUCTION Only persons are adequately familiar with batteries and with the required precautionary measures may replace batteries and supervise operations Unauthorised persons must be kept well away from the batteries Caution risk of electric shock The battery circuit is not isolated from the input voltage Hazardous voltages may occur between the battery terminals and the ground Before touching please verify that no voltage is present Batteries may cause electric shock and have a high short circuit current Please take the precautionary measures specified below and any other measures necessary when working with batteries remove wristwatches rings and other metal objects use only tools with insulated grips and handles When changing batteries install the same number and same type of batteries Do not attempt to dispose of batteries by burning them This could cause battery explosion Do not open or destroy batteries Escaping electrolyte can Cause injury to the skin and eyes It may be toxic Please replace the fuse only by a fuse of the same type and of the same amperage in order to avoid fire hazards Do not dismantle the UPS system 2 INTRODUCTION 2 1 Thank you Thank you for selecting this uninterruptible power supply UPS It is a State of the art electronic UPS that uses the latest technology 2 2 System Description The ARTon series UPS is ad
14. t which would overload the UPS system e g Laser printers to the UPS outlet socket Place cables in such a way that no one can step on or trip over them Do not connect domestic appliances such as hair dryers to UPS output sockets 1 SAFETY INSTRUCTION 1 4 Operation 1 5 Do not disconnect the mains cable on the UPS system or the building wiring socket outlet shockproof socket outlet during operations since this would cancel the protective earthing of the UPS system and of all connected loads The UPS system features its own internal current source batteries The UPS output sockets or output terminals block may be electrically lived even if the UPS system is not connected to the building wiring socket outlet Ensure that no fluids or other foreign objects can enter the UPS system The UPS operates with hazardous voltages Only qualified maintenance personnel may carry out repairs Maintenance servicing and faults The UPS system operates with hazardous voltages Only qualified maintenance personnel may carry out repairs Caution risk of electric shock Even after the unit is disconnected from the mains power supply components inside the UPS system are still connected to the battery and are still electrically live and dangerous Before carrying out any kind of servicing and or maintenance disconnect the batteries and verify that no current is present and no hazardous voltage exist in the terminals of high ca
15. ture LED Displa Mimic displa Sounds every 4 seconds after line fails Battery low Sounds every GE EE battery gt oda O 5 39 CG Ge Q mt Q o 5 o Zi C CD D Continuous alarm en a short circuit occurs the will no transfer to Bypass but emit a sustained tone Once the short circuit is removed the tone stops and the whole system operates normally again The UPS stops supplying power if the period of a short circuit is longer than 3 seconds Lightning Yes Surge NEMA 3R Dimension 31 0 900 660 mm Net Weight 320kgs 10 2 Physical Specifications Relative Humidit 90 maximum at 25 C non condensing Audible Noise 55dB ANSI A scale at 3 feet Operating Altitude Above sea level Operating Temperature F S C Protection LI ircuit LD Q OD CD n 0 4 800ft 40 C 104 F 4 800 7 000ft 38 C 100 4 F 7 000 10 000ft 35 C 95F 2 11 WARRANTY We warranty this product against defects in materials and workmanship for a period of 1 YEAR from the date of purchase and will repair or replace any defective UPS when directly returned to us For warranty claim please contact to your supplier to obtain a Return Authorization Number The defective part or unit should be returned at the Purchaser s expense to the authorized location normally this is the place of purchase A written statement describing the nature of the defect the date of purchase the Purchaser s name address email address a
16. vanced true on line sinewave UPS which provided reliable regulated transient free AC power to sensitive equipment ranging from computers amp telecommunication systems to computerized instrument Because the UPS is a true on line system conditioned power is provided continuously to the connected device Unlike the other standby UPS the UPS is constantly regulating filtering the output power When incoming power is blackout the UPS protects the computers instantaneously without any transfer time The ARTon series UPS has high nonlinear load current capability i e Crest Ratio 3 1 and this is suitable for powering special load such as switching power supplies The bypass function provides bypass power as its standby source During an overload condition the system will automatically transfer to the bypass line if a good power exists within 4 milliseconds to ensure the critical load in normal operation The system can transfer back to inverter automatically when the overload condition has been cleared within 4 milliseconds to ensure the critical load in normal operation 5 2 INTRODUCTION 3 PANEL DESCRIPTIONS 2 3 Block Diagram 1 O px zZ E RSR EE al z ke g 8 m s Gebei aLL AL UHE UPS Ieai ss 8 Q CH _ I LI lt a d U S a e ek 1 LCD STATUS DISPLAY UPS monitors its function by itself such T monitoring messages are displayed in the MULTIPLE
Download Pdf Manuals
Related Search