TVLogic PRM-902A User Manual - AV-iQ
Contents
1. 196 8 x 118 08 mm Viewing Angle a 7 Product Specification Power 12V DC Power Consumption Approx 36 Watts DC Operating Temperature O to 40 C 32 C to 104 c Storage Temperature 30 c to 50 C 22 C to 122 C Main Body Dimensions mm inch Main Body Dimensions With Rack Bracket Weight Accessory DC Power Adapter Above specifications may be changed without notice UOT EDTITIVdS AINPOdd o Jab MMOG www tvlogic co kr Suite 914 ACE TECHNO TOWER 9 345 30 Gasan Dong GuemChun Gu Seoul Korea E Tel 82 2 2026 1333 Fax 82 2 2026 13392. Used to select SDI A Input SDI B button lamp Used to select SDI B Input ANALOG button lamp Used to select desired Analog Input CVBS1 2 3 S Video Component RGB SCAN button lamp Used to transfer from OVER SCAN mode to ZERO SCAN mode Mode changes in the order of ZEROSCAN gt OVERSCAN gt PIXEL TO PIXEL gt ZEROSCAN This function is not available in Internal Pattern and Wave Form Vector Scope full size III AO ASPECT button lamp Used to toggle aspect ratio in SD from standard to anamorphic This function is not available in Internal Pattern and Wave Form Vector Scope full size MARKER button lamp Used to show MARKER on the screen The type of marker at work may be selected on the main menu This function is not available in Internal Pattern Wave Form Vector Scope full size Pixel to Pixel and HV Delay mode HVDELAY button lamp Used to activate the HV Delay mode This function is not available in Internal Pattern and Wave Form Vector Scope full size BLUE MONO button lamp You may remove R red and G green from the input signal and play the screen only with B blue signal Button may be pressed twice to change the screen to MONO mode This mode uses only Luminance value This function is not available in Internal Pattern and Wave Form Vector Scope full size AUDIO LEVEL button lamp Used to active AUDIO LEVEL METER on the screen The type of audio level meter at
3. gt Right Mid gt Right Clockwise Bottom gt Mid Bottom gt Left Bottom gt Left Mid gt Center gt HD 1080i 1080p DOWN Center gt Left Mid gt Left Bottom gt Mid Bottom gt Right Bottom Opposite gt Right Mid gt Right Top gt Mid Top gt Left Top gt Center gt OSD change Center gt Left Top gt Right Top gt Right Bottom gt left Bottom gt Center gt UP DOWN a ct E D m TI Cc mD 9 rt Po 16 UN Pixel To Pixel mode is available in SD mode but 1 1 sections cannot be rotated through as with HD sources Ss Other Functions Position in HD Signal 720p mode DOWN DOWN Ss DOWN DOWN 17 2 WaveForm WaveForm WaveForm WaveForm Size If push the Input button SDI A SDI B Analog WaveForm full mode is change to small mode automatically WaveForm Position This function is only available with SDI Input Ss 4 ae lor o TVlogie 3 VectorScope WaveForm Vector Scope OFF Vector Scope ON WaveForm Position Blending Refer to the WaveForm position blending above This function is only available with SDI Input to E PRM 902A MULTI CHANNEL LCD MONITOR 4 Audio Level Meter Audio Level Meter Avoid Overlap In full size WaveForm mode WaveForm shifts down to avoid the overlap with Audio Level Meter Audio Level Meter OF
4. work may be selected on the main menu This is available only SDI input WAVE VECTOR button lamp Used to activate the Waveform or Vector Scope Pressing the button once will activate the Waveform pressing the button twice activates the Vector Scope The type of waveform vectorscope work may be selected on the main menu This is available only SDI input UP button Used to navigate menu during OSD menu activation It may also be used to toggle clockwise through 1 1 quadrants in native scan mode DOWN button Used to navigate menu during OSD menu activation It may also be used to toggle counterclockwise through 1 1 quadrants in native scan mode MENU button Used to activate the OSD menu ENTER button Used to confirm a chosen value or mode within the OSD menu This can be used to control the position of Wave Vector in small size POWER button Power On Off button If the signal is normal LED lights in Green If the signal is unsupported or disconnected LED flashes in Yellow TALLY LED indicating monitor s current status using optional Remote Og LE JJed Ye 40 UOT IUNY Y AMEN PRM 902A MULTI CHANNEL LCD MONITOR AUDIO OUT DC IN 000000 000000 000000 ooodoo 2899900069 2899900059 2890900069 P 29900 q 009 000000000009 609200000 0 s_ S09900000509 D 609900G00 0 9929900000509 029000000505 000000505 000005 05 O o O o O 080 b 080 o 909000000004 909000000905 098 00000
5. 0905S p 0020000005 0900000006 00000009 00000000 O o 00000009 00000000 o o 00007009 00000000 Vo 00090009 AA Za SDI OUTPUT CVBS1 B Pb SDI B INPUT CVBS2 G Y S Y REMOTE SDI A INPUT CVBS3 R Pr S C FACTORY PGM SDI A IN BNC SDI A signal input terminal SDI B N BNC oves1 Pe e mocom PELES A oves2 SDI OUT BNC evesa pa a co SDI signal output terminal CVBS1 B Pb BNC Signal input terminal used for COMPOSITE1 RGB B COMPONENT Pb signals CVBS2 G Y S Y BNC Signal input terminal used for COMPOSITE2 RGB G COMPONENT Y SVIDEO Y signals CVBS3 R Pr S C BNC Signal input terminal used for COMPOSITE3 RGB R COMPONENT Pr SVIDEO C signals AUDIO OUT phone jack Used to audio output jack DC IN socket FACTORY PGM 15 pins Input connector for FACTORY PGM allowing for firmware updates REMOTE RJ 45 Pano Connection for remote control of monitor DC IN XLR 4 pins Used to supply DC power 12V TVlogic OSD Menu Organization amp Adjustment 1 MAIN Picture E tur me Picture Aperture Phase NTSC Setup Brightness This Item controls the degree of brightness Brightness can be adjusted by using the BRIGHT control knob on the front of the monitor Contrast This item controls the contrast ratio Contrast can be adjusted by using the CONTRAST control knob on the front of the monitor Chroma This item controls saturation Saturation
6. F Audio Level Meter ON This function is only available with SDI Input I 5 Time Code Time Code TETRA TBS 2 iar tT 7 Time Code Audio Level Meter Time Code Source ID AA PAE IA E Time Code WaveForm Full Size Time Code SourcelD WaveForm Audio Level Meter TE FRETE This function is only available with SDI Input Sm 6 Source ID Source ID Source ID Position E E zz Left Top Mid Top Right Top Left Bottom Mid Bottom Right Bottom Ss Ss Source ID Color ack me a Goon me vm System Default Value MEMU System Pagel System Page2 System Page3 Back Light DO Bo System Button Brightness Contrast Chroma Aperture Phase NTSC Setup 0 0 0 0 0 TOARE Color Temp 6500K Gain Red 1 2 3 0 Gain Green 1 2 83 0 Bias Red 1 2 3 Gain Blue 1 2 3 O O 0 Bias Green 1 2 3 Bias Blue 1 2 3 Color Copy Line Marker Center Marker Safety Area Maker Mat Marker Color Analog Channel Digital A Channel Digital B Channel Tally R Tally G System Default Blue Only No WaveForm Size Small WaveForm Position Right Bot WaveForm Blending Off Audio Level Meter Audio Channel Source ID G1 G2 Off Off Source ID Character CAM 1 Source ID Position Left Top S
7. LCD Racks Monitor A o a MUA MUSA Contents PRM 902A o e a haute 3 PPP ip e ii 4 Names Cuco ol Eac PAN canguru ao 5 OSD Menu Organization amp Adjustment cccnnnnnnconicaconananonanoncnonnonononononononnnnnos 8 Ogle Ul e il RN E E 15 Sic DS VOO riencia 24 caca a o A dd AE EA 26 s3u93U0 Warning Always use set voltage DC 12V If liquid is spilled on or impacts this product please disconnect the product immediately and seek professional help before continued use Keep unit disconnected during extended periods of disuse Keep unit in a well ventilated place to prevent overheating Do not install the product near any heat generating equipment Also keep the product out of direct sunlight or dusty areas Only clean the product with a noncommercial mild and neutral detergent When transporting the product make use of its original packaging for safer carriage FCC Federal Communications Commission This equipment has been tested and found to comply with the limits for class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interface when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equip
8. can be adjusted by using the CHROMA control knob on the front of the monitor Aperture This item controls the picture sharpness Phase This item controls Phase value Hue This function is only available in Composite and S Video NTSC Input NTSC Setup This item sets IRE value in NTSC mode between 0 IRE and 7 5 IRE This function is only available in NTSC Input Slim PRM 902A MULTI CHANNEL LCD MONITOR 2 MAIN Color Color Temp Gain Hed Sain Geen Gain Bue Bins Red BAG Sree Bias Mue olor loopy MENU Ext CAT Move Selec Color Temp This item controls Color Temperature with presets of 3200K 5600K 6500K 9300K and User 1 User2 User3 mode User On User Mode the user may select and control R G amp B GAIN BIAS values by using the UP DOWN ENTER buttons Color Copy In User mode user can copy the preset of 3200K 5600K 6500K or 9300K to make the custom adjustment by using the UP DOWN ENTER button 3 MAIN Marker Lime Marker Center Marker sat by Arca Marker Mini Marker Color White MENU Exit Car Move CENT Select Line Marker This selects the marker type when the MARKER is displayed on the screen Compatible MARKER types are as follows 16 9 4 3 4 3 ON AIR 15 9 14 9 13 9 1 85 1 2 35 1 1 85 1 amp 4 3 TVlogic Center Marker This item displays the CENTER MARKER on the screen Safety Area This item controls the size of t
9. e for SDI Signals Embedded Audio Level Meter Audio Out Built in Audio Disembedder and Internal Speakers Stereo Audio out using phone jack Knob Control Easy to adjust user configuration using the control knob BLUE amp MONO HN Delay Wide Variety of Markers amp Safety Areas Center Marker Safety Area Marker Aspect Marker Display Size Scan Pixel To Pixel Provides both full screen and unscaled native image Wide Screen CCFL Backlight 24Bit RGB LVDS Interface Panel DC Compatible The product is powered by normal 12V source Remote control function Simple remote controllability with single cable connection no additional modules required Additional Features Active Loop Through SDI 600 1 contrast ratio 600 cd m2 brightness OSD user interface Rack Mountable saun7 e9 y fal Y a SS U 40 LLI y O cC em Y U LL o 0 Name amp Function of Each Part LED lt FRONT gt A LEVEL METER HV DELAY ASPECT BRIGHTNESS CONTRAST CHROMA WAVE FORM BLUE amp MONO MARKER VOLUME SCAN ENTER BRIGHT knob Used to adjust the degree of brightness between MAX 25 and MIN 25 CONTRAST knob Used to adjust the contrast ration between MAX 25 and MIN 25 CHROMA knob Used to adjust the saturation between MAX 25 and MIN 25 VOLUME knob Used to adjust the volume between MAX 20 and MIN O SDI A button lamp
10. ecting BG Type or Char Type o Sb Source ID Character This item is used to customize the Source ID display A Z a z 0 9 and special characters Source ID Position This item controls the position of Source ID display Top Left Top Center Top Right Bottom Right Bottom Center Botttom Left Source ID Color This item is used to change the color of source ID display by selecting black white red green blue or yellow Time Code This item activates the Time Code Select between VITC or LTC Internal Pattern This item used to activa the Internal Pattern of 100 White or 100 Color Bar 7 MAIN System page3 Back Light This item controls the LED backlight setting The value should be within range between MIN 0 and MAX 15 Firmware Version This item is the firmware version of the system License x__m_ AA 8 SDI A INPUT Menu PRM 902A Series unit is capable of processing single SDI A Input signal Press SDFA button on the front of the monitor to select the SDIA input OSD menu displays as shown on the left SDI A Flf no image displays after selecting the desired input mode check and make sure that your connection is not 1920 Xx 1080 G l lose or disconnected Input resolution displays on the bottom of the OSD screen 9 SDI B INPUT Menu PRM 902A Series unit is capable of processing single SDI B Input signal Press SDI B button on the front of the moni
11. he SAFETY AREA between 80 85 88 90 93 and 100 Marker Mat This item darkens the area outside of MARKER setting area The degree of the matte is between OFF 0 and 7 The higher the number the darker MARKER the matte becomes Marker Color This item controls Marker color Selectable colors are white gray black red green and blue Line Marker Center Marker and Safety Area functions are operates only after activated by pressing the MARKER button on the front of the monitor 4 MAIN Remote PRM 902A REMOTE RJ 45 Analog Channel Pint Pin2 Pins Pin4 Pind Pin6 Pin7 GND Digital A Channel Digital B Channel TALLY R TALLY G Blue Only q1 2 3 A 5 6 T 8 MENU Exit AV Move ENT Select Pini Pin6 The user may connect RJ 45 jack to the remote terminal on the rear of the unit and designate a function for each pin The selectable functions are as follows 10 Classification Settable Values ANALOG CHANNEL DIGITAL A CHANNEL DIGITAL B CHANNEL TALLY RED TALLY GREEN BLUE ONLY UNDERSCAN ASPECT HVDELAY 16 9 MARKER 15 9 MARKER 14 9 MARKER 13 9 MARKER 4 3 MARKER 4 3 ON AIR MARKER 1 85 1 MARKER 2 35 1 MARKER 1 85 1 amp 4 3 MARKER CENTER MARKER SAFETY AREA 80 SAFETY AREA 85 SAFETY AREA 88 SAFETY AREA 90 SAFETY AREA 93 SAFETY AREA 100 Pin7 PIN7 is for POWER ON OFF use only 5 MAIN System page1 aveFoon Position Waverom Bend
12. ing y Level Metal Audo channel Ent AY Move Select System Default User can use the System Default menu to initialize the values of the monitor WaveForm Size This item controls the size of Waveform or Vector Scope o Sb TVlogic WaveForm Position This item controls the position of Waveform or Vector Scope between Right Center and Left In normal display press Enter button to activate this feature in activated WaveForm This feature can be activated in small size mode only WaveForm Blending This item activates the blending of Waveform or Vector Scope This feather activates automatically if WaveForm overlaps with OSD This feather can be activated in small size mode only Audio Level Meter This item set embedded audio group selects Off G1 G2 G2 G3 G3 G4 G1 G3 G1 G4 G2 G4 to activate Audio Level Meter Audio Channel This item set embedded audio channel selects CH1 CH16 Off WaveForm Size WaveForm Position and WaveForm Blending functions are operates only after activated by pressing the WAVE VECTOR button on the front of the monitor Menus or feathers which are related with WaveForm and Audio enables in SDI input mode only 6 MAIN System page2 Sanos D Characios CAM ol Source JD Position Left Top Source TD Cola Mack Time Code rr internal Pattern LMT ar Move CENT Solect Source ID This item is used to activate the source ID display by sel
13. ment in a residential to correct the interference at his own expense Z Warning Change or modifications not expressly approved by the manufacturer responsible for compliance void the user s authority to operate the equipment Disposal of Old Electrical amp Electronic Equipment Y i Applicable in the European Union and other European countries with separate collection systems 3 This symbol on the product or on its packing indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequence for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources Features Multi Format PRM 902A Series unit has the following features Compatible with varied SDI Signals The product is compatible with varied SDI signal 480i 576i 720p 10351 1080i 1080p 1080psf 2K Compatible with varied Analog Signals The product is compatible with varied Composite S Video signal NTSC PAL SECAM The product is compatible with varied Component RGB signal 4801 576i 4800 576p 720p 1080i 1080p Waveform Vector Scope Audio Level Meter Waveform amp Vector Scope availabl
14. ource ID Color Black Time Code Internal Pattern Scan Zero Scan Aspect Ratio Marker HV Delay Blue amp Mono Audio Level Meter WaveForm Vector 2 4 NTLeA ITNesog wersks O or Y U er T er U 9 a VA 1 U gt jo O C O Product Specification Analog Input 1 ae SDI 2 Channel Input Output 1 Screen SDI Output Active Through Out Composite 1 0Vpp With Sync S Video 1 0Vpp Y With Sync 0 286Vpp C Component 1 0Vpp Y With Sync 0 7Vpp Pb Pr Input Signal 1 0Vpp G With Sync 0 7Vpp B R 1 458Gbps 270Mbps Composite S Video NTSC 525 59 94i PAL 625 50i 480i 59 94 576i 50 480P 59 94 576P 50 Analog Input MA Component 1080i 60 59 94 50 Signal Format Spa rolas RGB SOG 1080P 30 29 97 25 24 24sF 23 98 23 98sF 720P 50 59 94 60 1080 60 59 94 50 SMPTE 274M 1080p 30 29 97 25 24 24sF 23 98 23 98sF SMPTE 296M 720p 23 98 24 25 29 97 30 50 59 94 60 SDI Inout Signal aii SMPTE 260M 1035i 60 59 94 Formats SMPTE 125M 4801 59 94 ITU R BT 656 5761 50 2K Format 2048 X 1080 23 98psf 24psf 23 98pst 24p Analog Stereo Phone Jack Internal Speaker 2 X 1W Stereo 9 inch Resolution 800 x 480 15 9 0 246 H X 0 246 V mm 16 7M true 24bit H 160 degrees V 140 degrees Luminance of white 600 cd m Center 600 Display Area
15. tor to select SDIB the SDI B input OSD menu displays as shown on the left 1920 X 1080 G l Flf no image displays after selecting the desired input mode check and make sure that your connection is not lose or disconnected lnput resolution displays on the bottom of the OSD screen 10 ANALOG INPUT Menu PRM 902A Series unit is capable of processing varied ANALOG Input signals Press ANALOG button on the front of the monitor and COMPOSITE 1 activate the OSD menu as shown on the left COMPOSITE 1 Select the input you desire by using the UP DOWN COMPOSITE 2 button and press the ENTER button to confirm O YA U qd O ga O He N Ww c He go gt O CJ E T dt 3 49 COMPOSITE 3 lf no image displays after selecting the desired input mode check and make sure that your connection is not SVIDEO lose or disconnected COMPONENT Input resolution displays on the bottom of the OSD RGB screen _a Move Select o X 480 60 ig SUOTIIUNY u3y10 Other Functions 1 PIXEL TO PIXEL PRM 483A monitor s Pixel to Pixel mode displays input signal without scaling To activate the Pixel to Pixel mode access the Scan menu in Syetem menu and select Pixel to Pixel In the Pixel To Pixel mode use the UP DOWN buttons to toggle between 1 1 scan sections Input Action Button Available Modes UP Center gt Left Top gt Mid Top gt Right Top
Download Pdf Manuals
Related Search