Mobeye WaterGuard CM2300 - Compound Security Systems
Contents
1. mobcye USER MANUAL Mobeye WaterGuard CM2300 Water leakage sensor SW version 1 n CONTENT General description Getting started Place a SIM card Connect the water sensor to the unit Place the batteries Enter the program mode Program at least one telephone number Switching on off Use of inputs and external power supply Using the input s Using external power Extended options Program mode The security code Programming the settings by SMS Possible General settings Phone numbers Identification text Alarm text Alarm notification type SMS or SMS call Input type Input delay time Inactive time Alarm repeat time Test SMS text message Power failure SMS message List of SMS commands for configuration Reset of system Request overview of the settings and status Status request Overview general settings Overview phone numbers Technical messages and status feedback ODOWDWDAWAAWAAOANNNNNNDDMDDAIAAWBWWWWWW N Attention Very important This user manual contains important guidelines for the installation and usage of the Mobeye device as described in this manual Please read these thoroughly before you start using the Mobeye device In case of damage caused by disregarding the guidelines the warranty expires The user must regularly check the proper functioning of the device The manufacturer cannot be held liable for any damage caused by any incorrect use or incorrect functioning of the Mobeye2. device Safety guidelines e The permitted ambient temperature during operation may not be exceeded not lower than 10 C and not higher than 50 C e The device is intended for use in dry and clean places e Protect the device from moisture heat and water splashing The guidelines for the battery usage must be regarded e Do not expose the device to strong vibrations e Do not let it fall from height Do not use in an environment where any inflammable gases vapors or dust are present or could be present e The repairs of the device may only be carried out by people trained for Mobeye repair e In case the device must be repaired only original replacement components may be used The use of different parts may lead to damage of the Mobeye device Use in accordance with the regulation The use of this device in accordance with the regulation is sending SMS text messages and making telephone calls after an alarm situation Other usages are not permitted Battery recycling CR123 batteries as used in the Mobeye WaterGuard are classified as non hazardous waste and can be recycled Please take empty batteries to a nearest collection point 1 GENERAL DESCRIPTION The Mobeye WaterGuard is a battery operated GSM module used to send out an alarm after detection of a water based fluid after a triggered input or if external power supply is used after a power failure It is also possible to monitor the water level in such a wa
3. Test SMS text message The Mobeye WaterGuard can send regular test SMS messages keep alive to the administrator to ensure the proper functioning of the unit The test message function is only active in case the unit is armed The interval between the test messages can be set between 0 days no test message and 30 days The default test interval is set to O no test message SMS command interval test message lt CODE gt TEST xx 4 4 10 Power failure SMS message In case the Mobeye WaterGuard is powered externally and the power fails it sends an SMS text message to the administrator The message is only sent in case the unit is armed This message can be set to OFF The default setting for the power failure SMS text message is set to ON SMS command power failure message lt CODE gt POWERSMS xx 4 5 LIST OF SMS COMMANDS FOR CONFIGURATION Setting SMS Command Range Default value Change security code INSTCODE lt xxxx gt 0000 9999 1111 Set telephone number for alarm TEL1 lt tel number gt Empty messages ae TEL5 lt tel number gt Delete telephone number DEL1 DELS Identification text NAME lt text gt 20 characters Mobeye Alarm notification type CALL lt type gt ON OFF ON Input type IN1 IN2 and IN3 TYPEIN1 lt type gt NO NC NO TYPEIN2 lt type gt TYPEIN3 lt type gt Delay on input 1 DELAY 1 lt sec gt 0 999 sec 1 Delay on input 2 DELAY2 lt sec g
4. Try the SIM card in any mobile wrong PIN telephone remove PIN code check credit replace SIM card Successful programming Blinking 3 times No action required action Faulty programming action Flashing 5 times Check SMS command Low batteries 4 flashes every 3 seconds Replace both batteries 11 Technical specifications GSM Quad band EGSM 850 900 1800 1900 MHz Antenna 900 1800 1900 MHz Batteries gt 2 CR123 lithium Battery life in normal mode gt 1 year Ext power connection 12 VDC 4 2 VDC min 500 mA optional Power consumption low power ca 50 pA stand by max ca 500 mA Power consumption 12V ca50 mA stand by max ca 500 mA Dimensions 80x 60x 40mm Ambient temperature gt 10 C until 50 C This manual is published by Mobeye All rights the translation included are reserved Any reproduction either photocopy microfilm or saved in an automated data dictionary only after written approval of the Publisher Reprinting even in summary is prohibited This user manual meets the technical requirements at the moment of printing Changes in technology and equipment are reserved Copyright 2013 by Mobeye version CM2300EN130331 12 CE Declaration of Conformity Herewith we Mobeye declare that the product Mobeye CM21 telemetry module And the derived products CM2000 CM2100 CM2200 CM2300 CM2300FS CM2400 CM2500 are in compliance with th
5. make sure the unit is in the program mode please refer to 4 1 5 1 STATUS REQUEST The status of the Mobeye WaterGuard can be requested by sending an SMS with the content lt CODE gt STATUS Upon sending this request the Mobeye WaterGuard returns the status to the originator of the request The status message includes the ARMED NOT CONFIGURED status of the Mobeye WaterGuard the status of the inputs the power and batteries 5 2 OVERVIEW GENERAL SETTINGS The general settings of the Mobeye WaterGuard can be requested by sending an SMS with the content lt CODE gt SET Upon sending this request the Mobeye WaterGuard returns the list of programmed settings to the originator of the request 5 3 OVERVIEW PHONE NUMBERS The list of telephone numbers can be requested by sending an SMS message with the content lt CODE gt CALL Upon sending this request the Mobeye WaterGuard returns the list of programmed telephone numbers to the originator of the request 10 6 TECHNICAL MESSAGES AND STATUS FEEDBACK Technical messages are In case of technical issues the administrator receives an SMS message Possible messages are Message Reason Low batteries external power supply Power is available batteries need to be replaced OK No external power supply batteries No external power supply batteries are capable OK to take over operation in low power mode Low batteries no external power No external power
6. supply batteries need to be supply replaced External power supply OK batteries The external power is restored or the adapter is OK plugged in a socket batteries do not need to be replaced Message s missed due to One or more SMS text messages couldn t be Network SIM failure sent due to a SIM card failure or GSM network failure When receiving one of the above mentioned technical messages please take appropriate action as soon as possible During the battery replacement the SIM card does not have to be removed Status feedback Status LED pattern Required action Module not configured Blinking 1 second on 1 Configure at least one second off telephone number Module is switched on 1 flash every 3 seconds No action required powered by batteries Module is switched on On No action required powered by an external source Module establishes Blinking 2 seconds on 1 Wait until the network network connection to second off connection is established and send an alarm message the message is sent Module establishes Blinking 3 seconds on 1 Wait until the network network connection to get second off connection is established to program mode before programming No GSM connection 2 flashes every 3 seconds Try the SIM card in any mobile telephone replace SIM card using other telecom provider try the module at another location No valid SIM card or 3 flashes every 3 seconds
7. the non alarm status within the delay time no alarm is sent The time can be set between 0 and 999 seconds As default the input delay time is set to 1 second SMS command alarm delay input 1 lt CODE gt DELAY1 xxx SMS command alarm delay input 2 lt CODE gt DELAY2 xxx SMS command alarm delay water sensor lt CODE gt DELAY3 xxx 4 4 7 Inactive time The inactive time defines the time input 1 or input 2 is not active after an activation In case the time is set to 0 minutes the input is active again immediately after returning to the non alarm status In case the time is set to e g 30 minutes the input remains inactive for the first 30 minutes In case the input is again or still activated after these 30 minutes a new alarm message is sent The time can be set between 0 and 60 minutes As default the inactive time is set to 0 SMS command inactive time input 1 lt CODE gt INACTIVEIN1 xx SMS command inactive time input 2 lt CODE gt INACTIVEIN2 xx SMS command inactive time Water sensor lt CODE gt INACTIVEIN3 xx 4 4 8 Alarm repeat time In order to emphasize the urgency of the alarm messages all alarms can be repeated As long as the alarm status has not returned to the inactive status the SMS alarm will be repeated after the alarm repeat time The time can be set between 0 and 24 hours As default the alarm repeat time is set to 4 hour SMS command alarm repeat time lt CODE gt REPEAT xx 4 4 9
8. D OPTIONS To program the Mobeye WaterGuard the GSM module must have network connection In case only batteries are used first switch the unit to the program mode Next send SMS commands for the configuration All settings are stored and will be kept in the unit even in case the power supplies are removed 4 1 PROGRAM MODE Directly after placing the batteries the Mobeye WaterGuard switches to the program mode First the GSM module establishes network connection During this time the LED flashes 2 sec on 1 sec off Within 10 30 seconds the connection is established and the status LED starts flashing 1 sec on 1 sec off or on in case the first telephone number has been configured The Mobeye WaterGuard returns to the program mode by pressing the on off button during 5 seconds until the LED starts flashing or turns to on As long as the unit is in the program mode the status LED is on or flashing 1 sec on 1 sec off in case the module has no configuration During the first 3 minutes the GSM module remains open ready to receive SMS commands After 3 minutes a time out occurs and the GSM module switches off in order to save the batteries The unit returns to the low power operational mode In case the unit is connected to an external power supply the WaterGuard has network connection all the time and the unit is in program mode all the time The program mode is interrupted by pressing the on off button during one second un
9. code 0000 or without PIN code Connect the water sensor to the unit Place the batteries Enter the program mode Program at least one telephone number administrators number Arming disarming the system Aaron gt These steps are further explained in this chapter After these steps the module will be operational 2 1 PLACE A SIM CARD Open the enclosure with the 4 screws and insert a SIM card into the module Push the black cover outward slightly to open the holder Before installing the SIM card should have PIN code 0000 or be free of a PIN code A PIN code can be changed or removed by putting the SIM card in a mobile phone and change or remove the PIN in the security menu NB make sure the SIM card is inserted before the batteries are placed In case of a SIM card change please first remove the batteries and remove any other external power supply 2 2 CONNECT THE WATER SENSOR TO THE UNIT Plug the external water sensor into the metal socket and press it firmly 2 3 PLACE THE BATTERIES Place the two batteries CR123 in the module Use the indication for the correct placement The green LED will flash to indicate that the module is not configured at least one telephone number should be programmed 2 4 ENTER THE PROGRAM MODE Directly after placing the batteries the Mobeye WaterGuard switches to the program mode First the GSM module establishes network connection During this time the LED flashes 2 sec on 1 sec
10. command 1 telephone number lt CODE gt TEL1 lt tel number gt SMS command 2 telephone number lt CODE gt TEL2 c lt tel number gt similar for TEL3 TEL5 To delete telephone numbers SMS command delete 1 telephone number lt CODE gt DEL1 similar for DEL2 DEL5 In case a foreign number needs to be entered start with 00 follow by the country code e g 0031612345678 4 4 2 Identification text It is possible to add a standard identification text NAME to all messages sent out by the Mobeye WaterGuard The alarm messages are a combination of the name and the alarm text A user defined identification has a length of maximum 20 characters The default identification text is Mobeye SMS command identification text lt CODE gt NAME lt free text gt 4 4 3 Alarm text Unique alarm texts can be programmed into the Mobeye WaterGuard User defined texts have a maximum length of 20 characters Following default texts are programmed Water alarm lt TEXT1 gt Water alarm Waiter level restored lt TEXT2 gt Water level OK Triggered input 1 lt TEXT3 gt Alarm 1 Triggered input 2 lt TEXT4 gt Alarm 2 SMS commands text 1 lt CODE gt TEXT1 lt free text gt SMS commands text 2 lt CODE gt TEXT2 lt free text gt similar for TEXT3 and TEXT4 4 4 4 Alarm notification type SMS or SMS call As default behaviour after an activated input the Mobeye WaterGuard notifies by SMS text message followed by a t
11. e essential requirements of the following European standards EU Directives Directive 73 23 EEC low voltage directive Directive IEC EN 50130 Electromagnetic compatibility Directive 1995 5 EC R amp TTE Radio amp Telecommunications Terminal Equipment The conformity with the essential requirements of 1995 5 EC has been verified against ETSI EN 301 489 1 V1 5 1 ETSI EN 301 489 7 V1 2 1 ETSI EN 301 511 V9 0 2 CENELEC EN 60950 2001 Mobeye B V Poeldonkweg 5 5216 JX s Hertogenbosch The Netherlands Name J P K van de Vijver Position General Manager 31 maart 2013 13
12. elephone call beep signal The combination of SMS text and the call increases the chance of getting the attention of the contact persons It is possible to disable the call OFF so that only an SMS message will be sent The default alarm notification type is ON SMS call SMS command alarm notification type lt CODE gt CALL xxx 4 4 5 Input type As default behaviour the Mobeye WaterGuard sends out an alarm after detection of a water based fluid In case the water level in a tank should be monitored the WaterGuard needs to send out the alarm as soon as the sensor detects the absence of water As default the input type IN3 is set to NO normally open for alarming the absence of water IN3 needs to be changed to NC normally closed SMS command input type input 3 lt CODE gt TYPEIN3 xx The input types IN1 and IN2 define the character of the additional inputs IN1 and IN2 This can be Normally Open NO or Normally Closed NC In case an input is set to NO the alarm will be triggered as soon as the terminals of the input are closed If the input is set to NC the alarm is triggered in case the connection between the input terminals is broken The default input type is set to NO SMS command input type input 1 lt CODE gt TYPEIN1 xx SMS command input type input 2 lt CODE gt TYPEIN2 xx 7 4 4 6 Input delay time The input delay time defines the time that the input are triggered before an alarm is initiated If the input returns to
13. g 9 9 appropriate wire material T E When using a second input connect this to input 2 As default the inputs are programmed as Normally Open NO contacts 6 This means the inputs are triggered in case the input is closed during at least 1 second In case the contact should be Normally Closed NC please refer to paragraph 4 4 5 In case a sensor should be activated shorter or longer before evoking an alarm please refer to 4 4 6 3 2 USING EXTERNAL POWER Although the Mobeye WaterGuard is designed to run on batteries it is possible to use an external power supply In this mode the module is always in connection with the GSM network and therefore always in program mode In case the power fails the batteries take over the functioning and the administrator is informed by an SMS text message The module continues operating albeit in the low power mode This means the GSM module switches off and only establishes network connection in case it needs to send out an alarm test message or battery low alert j o eey Connect the external power adapter or any other regulated 12VDC ojo o iE O power supply to the power input of the connector press on the green ail cn24i pins for connecting the wires a 6 fe m i V black lead with white stripe to j Ground black lead to S pogo 2 4 EXTENDE
14. off Within 10 30 seconds the connection is established and the status LED starts flashing 1 sec on 1 sec off or on in case the first telephone number has been configured The Mobeye WaterGuard returns to the program mode by pressing the on off button during 5 seconds until the LED starts flashing or turns to on As long as the unit is in the program mode the status LED is on or flashing 1 sec on 1 sec off if the module has no configuration During the first 3 minutes the GSM module remains open ready to receive SMS commands After 3 minutes a time out occurs and the GSM module switches off in order to save the batteries The unit returns to the low power operational mode 2 5 PROGRAM AT LEAST ONE TELEPHONE NUMBER The Mobeye WaterGuard is able to send messages up to 5 telephone numbers The first telephone number belongs to the administrator Technical messages like battery low are sent to the administrator only Without the administrators phone number the Mobeye WaterGuard cannot not function When the WaterGuard is in initial factory status and the batteries are placed so the LED is flashing the administrators number is programmed by calling the telephone number of the Mobeye WaterGuard using the administrators phone The unit will recognize this number and store it as administrator telephone number 1 The administrator will receive a confirmation SMS text message including the security code Thi
15. s code is needed to program the other settings in the unit NB for this way of programming the number recognition in the administrator s phone must be on To program or change the administrators number by SMS command please refer to 4 4 1 2 6 SWITCHING ON OFF After the previous steps the Mobeye WaterGuard is ready for use It is armed switched on automatically The green LED blinks once in 3 seconds In order to switch off disarm the Mobeye WaterGuard Press the on off button at the upper side for 1 second The green LED switches off to indicate the armed status In order to switch on arm the Mobeye WaterGuard Press the on off button at the upper side for 1 second The green LED blinks once in 3 seconds or permanently in case of an external power supply to indicate the armed status 3 USE OF INPUTS AND EXTERNAL POWER SUPPLY 3 1 USING THE INPUT S It is possible to connect external sensors to the inputs As a standard reaction after a triggered input the Mobeye WaterGuard sends an SMS text message to the preset numbers and calls these numbers Insert the 2 wires of an external sensor through the hole of the enclosure to the inside part and next in the two connectors of input 1 press on the green pins for connecting the wires It does not matter which wire is connected to which J g cN24 goo ry o o a me o connector If necessary the wires can be extended up to 5 meters usin
16. t 0 999 sec 1 Delay on water sensor DELAY3 lt sec gt 0 999 sec 1 Inactive time input 1 INACTIVEIN1 lt min gt 0 60 min 0 Inactive time input 2 INACTIVEIN2 lt min gt 0 60 min 0 Inactive time water sensor INACTIVEIN3 lt min gt 0 60 min 0 Alarm repeat time REPEAT hh 0 24 hrs 4 Alarm text after water detection TEXT1 lt text gt 20 characters Water alarm Alarm text after end of water detection TEXT2 lt text gt 20 characters Water level OK Alarm text input 1 TEXT3 lt text gt 20 characters Alarm 1 Alarm text input 2 TEXT4 lt text gt 20 characters Alarm 2 Interval test SMS TEST lt days gt 0 30 days 0 Power failure SMS POWERSMS lt xx gt ON or OFF ON Examples Set phone number1 Delete phone number 4 6 RESET OF SYSTEM 1111 TEL1 0612345678 1111 DEL1 To reset the Mobeye WaterGuard to its factory settings Remove the batteries Press the outside button while entering the batteries Keep it pressed for about another 5 seconds Release the button immediately after the LED starts to flash After a successful reset the status LED on the keypad will blink green to indicate that the module is not configured The security code lt CODE gt is back to factory settings as well 5 REQUEST OVERVIEW OF THE SETTINGS AND STATUS The programmed settings and status of the GSM detector can be received per SMS message Before sending the request
17. til the LED switches off The unit is switched off completely disarmed 4 2 THE SECURITY CODE For configuration activities the security code of the Mobeye WaterGuard must be used The initial security code is 1111 In this manual this code is referred to as lt CODE gt 4 3 PROGRAMMING THE SETTINGS BY SMS The settings are programmed by SMS text messages Be sure the WaterGuard is in program mode please refer to 4 1 Send an SMS message with following content lt CODE gt lt command gt Do not forget the space character between lt PIN code gt and lt command gt The commands are case sensitive Several commands may be combined in one SMS message with a maximum of 160 characters by placing a between the commands lt CODE gt lt command1 gt lt commanda23 gt lt commandN gt The green LED blinks 3 times to indicate the successful configuration In case of an incorrect command the LED flashes 5 times In 4 5 the complete scheme with SMS commands is listed 4 4 POSSIBLE GENERAL SETTINGS This paragraph describes the general settings for the WaterGuard 4 4 1 Phone numbers The Mobeye WaterGuard is able to send alarm messages up to 5 phone numbers The first telephone number TEL1 belongs to the administrator Only this number receives all system messages The other phone numbers including the administrator only get the alarm messages To set or change telephone numbers SMS
18. y that the Mobeye WaterGuard detects the absence of water The Mobeye WaterGuard is pre programmed with standard action reaction patterns To change this behaviour please refer to chapter 4 The factory settings of the Mobeye WaterGuard cause following reactions When the Mobeye WaterGuard detects water it sends an alarm SMS text message and calls to the phone numbers as programmed The SMS message contains the text Mobeye Water alarm As soon as no water is detected anymore an SMS text message is sent to the set telephone numbers containing the text Mobeye Water Level OK In case one of the inputs is activated by a sensor the Mobeye WaterGuard sends an alarm SMS text message and calls to the phone numbers as programmed by the user In case the water sensor and or the inputs remain in the alarm status the Mobeye WaterGuard repeats sending the SMS alarm message every four hours In case the batteries need to be replaced the Mobeye WaterGuard sends a battery low SMS text message to the administrator In case an external power supply is used and a power failure occurs the Mobeye WaterGuard sends a power failure SMS text message to the administrator In case the power is restored the Mobeye WaterGuard sends a power restored SMS text message to the administrator 2 GETTING STARTED To get started with the Mobeye WaterGuard at least the following steps need to be taken in following order Place SIM card with PIN
Download Pdf Manuals
Related Search