GAS CONVERSION KIT FROM NG TO LP (PROPANE
Contents
1. 7 TWIN EAGLES Defining the Art of Outdoor Cooking GAS CONVERSION KIT FROM NG TO LP PROPANE P N CKLP TEBQ 1 All gas connections conversions should be made by a qualified technician and in accordance with FOR MODELS TWIN EAGLES GRILLS TEBQ TPBQ local codes and ordinances 2 Before conducting a conversion to a gas appliance verify that the main gas is shut off and disconnected from the appliance 3 Ensure that you have the LP Gas Conversion Kit as follows a moans P N 15110 53 Orifice 53 LP Grill Burner P N 15108 57 Orifice 57 Rotis Small IR for TEBQ 30 TPBQ 30 LP P N 15108 56 Orifice 56 Rotis Large IR for TEBQ 42 TPBQ 42 LP P N 15302 LP Regulator with 24 Hose P N 12602 Coupling 3 8M flare X 1 2 FIP P N 18351 Label Conversion Gas 4 Replace burner valve orifices a Grill Burner i Remove cooking grates ii Remove briquette trays i Remove grill burners iv Remove grill burner orifices 41 drill size v Replace grill burner orifices with 53 drill size 3 pcs 1 pe 1 pe 1 pe Ipe Ipe vi Install back the burners briquette trays amp cooking grates WARNING IT IS CRITICAL THAT THE GAS BURNERS ARE PROPERLY INSTALLED WITH THEIR ORIFICES INSIDE THE BURNERS AIR SHUTTERS If not properly installed gas may leak outside of the burner that could lead to fire potential damage to your grill and bodily injury b Infrared Rotisserie Burner i Remove2. rear hood cover to expose infrared burner gas orifice ul Remove rotis burner orifice as follows 1 50 from the 30 grill TEBQ 30 TPBQ 30 2 48 from the 42 grill TEBQ 42 TPBQ 42 ii Replace rotis burner orifice with 1 Orifice 57 for 30 grill TEBQ 30 TPBQ 30 2 Orifice 56 for 42 grill TEBQ 42 TPBQ 42 iv Replace rear hood cover Replace the NG regulator with the factory supplied LP regulator a Disconnect regulator from grill b Install the brass coupling 2 female pipe x 3 8 male flare c Install the factory supplied regulator and hose assembly Connect the flare end of the hose to the grill coupling using a 34 open wrench Do not apply pipe sealant to the s flare connection Connect the regulator to the LP cylinder hand tighten it do not use a wrench d Check for gas leaks using soapy water solution NEVER USE THE GRILL WITHOUT FIRST LEAK TESTING THE GAS CONNECTION a Prepare a leak testing solution of sudsy water by mixing in a spray bottle with half liquid soap and half water Confirm that all control knobs are in the OFF position Turn the main gas valve supply ON Apply leak testing solution by spraying on the pipe joints fittings and hose e aos A gas leak is detected 1f i there is a faint gas smell and or li growing bubbles appear on any of the connection points and or hose DO NOT attempt to ignite the grill and IMMEDIATELY turn off the gas supply valve f When ther
3. e is a gas leak call a qualified service technician DO NOT use the grill until the leak is corrected Calibrate burner low flame setting a The grill must be hooked up to the gas supply in order to calibrate burner b Turn on burner and set to low At low setting all ports of the burner must remain lit If the flames are too high or too low calibrate burner valve c To calibrate burner valve pull off valve knob Insert a skinny flat screwdriver into the valve stem d Turn the adjusting screw inside the stem clockwise to decrease flame or counter clockwise to increase flame e Perform leak test on the valve stem using the soapy water solution The conversion is complete Fill up the Conversion Label Next paste it next to the original Serial Plate The unit is ready for installation Please refer back to the User s Manual to insure safety proper care and operation PN 18566B 04 11
Download Pdf Manuals
Related Search