A400 XPRESSO User Manual - Future
Contents
1. 40 LOMESSAGES PROM THE SYS TEM 4 9 0 LIMITED ONE YEAR WARRANTY isisisi 44 1 SAFETY INSTRUCTIONS CORRECT USE OF THE PRODUCT This appliance is intended for home use in accordance with the descriptions and instructions contained in this manual Please read the instructions carefully and keep them as they could be useful to you in the future ATTENTION e This appliance is built according to current regulations for recycling e Donot throw away the packing materials used to protect the appliance during transportation but take them to relevant collecting centers e Useonly original spare parts e Weare declines liability for any damage or accident derived from any use of this appliance which is notin conformity with the instructions contained in this booklet IMPORTANT All our products undergo strict controls before leaving the company Evidence of this may be present by means of ground coffee powder in the machine water droplets and other traces of coffee making functions PRECAUTIONS KEEP THESE INSTRUCTIONS e Read these instructions for use carefully before using the appliance e Usewhich does not comply with these instructions will invalidate the warranty e The wiring system to which the appliance is connected must always comply with the laws in force e Before connecting the appliance make sure that the mains voltage is the same as the voltage indicated on the data label of the appliance2. Programming is complete and the system returns to the Off Standby mode 26 4 4 AUTO OFF TIME STAND BY TIME This function allows you to determine how much time the system waits after the machine operates for the last time before entering into the Off Stand by mode The following settings are possible e Never Spoon e 30minutes Spoon lbean e 2hours Spoon 2beans e 5hours Spoon 3beans NOTE The factory setting is 5 hours 44 Switch the machine off using button 2 standby mode 44b Press the Service button 7 for about two seconds to enter the programming mode 44c The symbols Filter Water Hardness Cup Time will come on in sequence 44d Wait for the symbol Time to illuminate on the display and then press the selector button 4 once 44e The factory default setting 5 hours will display 27 440 Press the selector button again 4 repeatedly until the desired time symbols appears the display 4 4g Confirm the new selection by pressing the Service button 7 for about two seconds Programming is complete and the system returns to the Off Standby mode Important The time setting will be lost if you turn off the power 15 unplug the machine or if the power goes off 28 5 NB MAINTENANCE AND CARE REPLACING THE OPTIONAL FILTER 25 After filtering about 50 liters of water the filter is longer effective This is signaled on the display by the symbol Filter and the flas
3. EMPTY TRAYS and WATER TANK appear on the display 5 2 Remove the drip tray 9 and the water reservoir 17 and empty them 5 21 Fill the reservoir 17 with cold water and put the reservoir and drip tray 9 back in position 5 2m Thesymbol TURN VALVE will appear on the display turn the steam hot water knob 11 clockwise to the right 5 2 The system is again rinsed intermittently through the steam nozzle 12 for about 5 minutes 5 20 When symbol TURN VALVE appears on the display turn the steam hot water knob 11 anti clockwise to the left 5 2 The system is rinsed through the nozzles 8 and water flows into the drip tray for about 5 minutes or until the water tank 17 is emptied 524 When the cycle has completed the symbol EMPTY TRAYS appears on the display 5 2r Empty the drip tray 9 and reassemble it into the machine 5 25 The system quickly heats up to the correct temperature 38 5 24 The service button 7 flashes Press the service button 7 to rinse the system out through the coffee dispensing nozzles 8 5 2u The machine is now ready for regular use again MANUAL LIME SCALE REMOVAL If necessary you can run the descaling cycle at any time even if the alarm does not appear on the display 5 2 Switch the machine ON using button 2 Operating mode 5 2w Press the Service button 7 for about two seconds The symbols tablet Descale wil begin to flash in sequence
4. This appliance is fitted with non rewirable plug if it is necessary to change the fuse in a non rewirable plug the fuse cover must be refitted If the fuse cover is lost or damaged the plug must not be used until a replacement available from the manufacturer is obtained It is important that the replacement cover corresponds with the color markings on the base of the plug If the plug requires to be changed because it is not suitable for your plug socket it should be cut off and an appropriate replacement plug fitted following the wiring instructions below The plug removed must be disposed of safely as an insertion into 13A socket is likely to cause an electrical hazard Green Yellow Earth Fuse 13Amp Blue Neutral Brown Live 7 0 MESSAGES FROM THE SYSTEM SYMBOLS FILL UP PIPE SY S FILL WATER FILL BEANS MEANING The water conveyance system has water steam Water reservoir 17 is empty Water reservoir 17 has been removed or is incorrectly installed Outof coffee beans 41 WHAT TO DO Open hot not been filled knob 11 Fill with cold water Install the water reservoir Fill the container 18 with coffee beans Important The words FILL BEANS will remain on the display until you make coffee EMPTY TRAYS TRAYS MISSING SY STEM HOT PLEASE CLEAN SYSTEM CALCIF FILTER CHANGE CLOSE THE DOOR The tray 9b and or coffee grounds container 9c is full and or container The tray 9b an o
5. machine is now ready for use 2 2 ASSEMBLING THE MILK FROTHING ACCESSORY IMPORTANT Assemble all components of the manual milk frothing accessory as shown in fig A leaving no space between components Take special care to ensure that the O ring seal on the black plastic tip 12b is inserted all the way into the Stainless Steel Tube 12a and threaded onto the pipe from the machine 2 3 USING YOUR COFFEE MACHINE FOR THE FIRST TIME Priming the system When you use this appliance for the first time the pipes inside the machine may not yet be filled with water The machine will display the symbol circle with arrow upon powering up The steam hot water knob 11 must be set to 0 23 After turning the machine On with the on off button 2 the symbol circle with arrow will appear on the display 1 2 3 0 the steam hot water knob 11 clockwise to the right At this point the system will begin to pump and fill with water Water will start to flow out of the nozzle 12 23 Once the symbol circle with arrow begins to flash turn the knob 11 anti clockwise back to the 0 position 10 23d the machine has heated up to the correct temperature the Service button 7 will start flashing 2 3 the Service button 7 to rinse the system out through the coffee dispensing nozzle 8 Important This rinsing step cannot be left out as no other function will operate until this cycle h
6. 2 cup selector 6 Important If the machine should run out of water or coffee beans between the two cups or if the trays need emptying a signal will appear and the second cup of coffee will not be made Follow the instructions to top up the machine and press only the 1 cup selector 5 to make the second cup of coffee 3 5 BREWING WITH PRE GROUND COFFEE 35a Firstturn the water quantity control knob 3 to the desired quantity of water for one cup 3 50 Open the lid to access the ground coffee compartment 20 The symbol POWDER will flash on the display 1 3 5 Fill with one level measuring scoop 23 of ground coffee and close the lid The symbol POWDER will appear on the display 3 5 Place one cup under the coffee dispensing nozzle 8 and press the 1 cup button 5 Note If you unintentionally open the ground coffee compartment and do not press the coffee button after putting ground coffee into it the machine will automatically perform a rinsing cycle through the coffee dispensing nozzle 8 one minute after the lid is closed and will then be ready for use again Important The Pre Ground compartment 20 15 not a coffee storage compartment N ever put more than one scoop 23 into it and use only freshly ground or vacuum packed coffee Do not use instant coffee Y ou can make instant coffee in the cup by drawing hot water from the nozzle 12 3 6 DRAWING HOT WATER 3 6 Place a cup under the nozzle
7. months No signal will appear on the display and the new filter must be replaced manually TIP As a reminder you may set the replacement date on the wheel on the top of the filter 5 0i Switch the machine ON using button 2 Operating mode 5 0 j Press the Service button 7 for about two seconds The symbols spoon filter wil begin to flash in sequence 5 0k Wait until the Filter symbol filter displays and press the Service button 7 once briefly to confirm 5 01 The symbol filter will now begin to flash 5 0m Press the Service button 7 for about two seconds The symbols Filter Water Tank Time will diplay 5 0n Wait for the symbol Filter to illuminate on the display and then press the selector button 4 once 5 00 Remove the water tank 17 and install the replacement filter using the supplied filter assembly tool 23 50 Fill the water tank 17 with cold fresh water to the max mark on the tank and insert it back into the machine The symbol Time wil begin to flash 5 0q Place a recipient under the Hot water Steam nozzle 12 and turn the knob 11 clockwise to the right The system will now perform a brief rinsing cycle to flush out the old unfiltered water 5 0r Wait until the water stops flowing out of the Hot water Steam nozzle 12 and then close the knob 11 anti clockwise to the 0 position 505 The following may happen next e Thesystem quickly heats up and is
8. ready for use again 31 e The Service button 7 may carry on flashing If this happens press the button 7 once to conduct another short rinse cycle through the coffee outlets 8 this is normal The system will now be ready for filtered water use 32 5 1 CLEANING PROGRAMME IMPORTANT This program is intended solely for cleaning the coffee dispenser assembly It is not the L ime Scale Removal program IMPORTANT Please follow these steps to the letter The cleaning program cannot be interrupted once it has started The cleaning program thoroughly cleans all dispensing assemblies removing coffee residues and oily deposits which can build up and block up the machine To run the program use the special X presso Cleaning Tablets available through X presso Direct 66 2 906 8118 When the machine requires a clean the symbol Tablet will appear on the display and the service button 7 will flash RECOMMENDATION Start the Cleaning cycle only when you want to perform the clean Y ou may continue making coffee hot water and steam but we recommend you perform the cleaning cycle promptly 33 5 2 Press the Service button 7 for about two seconds The symbol drip tray will begin to flash 5 2 6 Remove the drip tray 9 and the water reservoir 17 and clean those thoroughly using only water 5 2 Fill the Water Reservoir 17 with cold water and re assemble and insert drip trays 9 back into the mac
9. the result of a roasting process Darker coffee beans have been roasted for a longer time at a higher temperature and more aromatic than lighter coffee beans There are many different types of coffee available on the market containing blends of beans roasted at different temperatures with different types of aroma There is also decaffeinated coffee containing only 2 caffeine Try using different types of coffee with your espresso machine to fine tune the flavor and aroma that best suits your taste Ideally coffee beans should be ground just before using them Remember that your coffee MUST BE GROUND FOR PUMP ESPRESSO MACHINES which means it must be ground quite finely It is good idea to Keep ground coffee in a hermetically sealed container as coffee easily absorbs odours USEFUL INFORMATION WATER QUALITY e IMPORTANT To prevent problems caused by lime scale build up it is important to use the machine with the optional water softening filter 25 Alternatively you may also use lime scale remover descaling tablets or the Lime O Powder available from X presso Direct 66 2 906 8118 as described in the section on the lime scale remover program If you decide to use the optional water softening filter follow the assembly instructions under the heading Filter assembly 2 OPERATIONAL START UP 2 1 PREPARING THE COFFEE MACHINE 21 Unpacking Carefully remove the machine and all accessories from the packag
10. 12 3 6 the Steam H ot W ater knob 11 clockwise to the right 3 6 When the Hot water comes out of the nozzle the symbol HOT WATER will flash on the display 1 36d the cup up to the desired level and then turn the knob 11 anti clockwise back to 0 again WARNING Be careful not to burn yourself hot water may splash The nozzle 12 reaches high temperatures while in use Let it cool down for a few minutes before touching it 3 7 DRAWING STEAM AND FROTHING MILK 3 7 a Press the steam preheat button 10 The symbol STEAM WARMING will appear on the display 1 373 Oncethe system is ready the symbol STEAM READY will appear on the display 0 3 7 Immerse the nozzle tip 12 in the cup full of liquid to be heated 37d the steam hot water knob 11 clockwise to the right Important A little water will come out before the steam this is normal 18 3 7 the operation is completed turn the knob 11 anti clockwise back to 0 to stop 3 7 IMPORTANT Press the steam preheat button 10 again to restore normal operation of the machine NOTE Steam may continue to be produced for maximum 2 minutes after which the machine will automatically stop the procedure To continue with the procedure first turn the knob 11 anti clockwise back to 0 Then turn the knob 11 clockwise to the right to continue WARNING scalding steam hazard The steam is very hot Grasp
11. 5 2x Wait until the symbol Descale displays and press the Service button 7 once briefly to confirm The symbol Descale begins to flash 52 the Service button 7 for about two seconds The symbol drip tray will begin to flash 5 22 Proceed from point 5 2b above as described in the Lime Scale Removal section 39 5 3 GENERAL CLEANING IMPORTANT TIPS e Never submerge the appliance in water e not use abrasive cleaners e Clean the case inside and out using only a soft damp cloth e Empty the drip tray 9 and the coffee grounds container 9c only when instructed to do so by the symbol on the display e Clean with warm soapy water occasionally e When cleaning the drip tray 9b always remember to clean between the metal contacts 9b at the back of the tray e Rinse out the water reservoir every day and refill it with fresh cold water e Clean the hot water and steam nozzle with damp cloth after each use 40 6 0 MAINS AC OPERATION FOR YOUR OWN SAFETY READ FOLLOWING INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO CONNECT THIS UNIT TO THE MAINS e This unitis designed to operate 240V 50 Hz current only Connecting it to other power sources may damage the unit and will void the warranty e IMPORTANT Flipping the power switch 15 whileinfusion is in progress may result in damage to the appliance Turn off the power only when the on off button 2 is set to off stand by mode
12. Dear Customer Thank you for choosing A 400 With this coffee machine you will enjoy full taste and aroma right from the first cup and make creamy cappuccino as well as tea and other hot drinks A 400 is made with top quality components to ensure quality and perfect safety Please read these instructions carefully before using our machine IMPORTENT This appliance is not intended for use by persons incl children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning the use of the appliance by a person responsible for their safety MACHINE CONTROLS AND COMPONENTS 1 Display 2 On off button 3 Knob for adjusting amount of water in cup 4 Coffee strength selector 5 1 cup selector 6 2 cup selector 7 S service button 8 Coffee dispensing nozzle with adjustable height 9 Drip tray amp grid a Grid b Drip tray c Coffee grounds container d Metal Contacts 10 Steam preheating button 11 Steam hot water knob 12 Steam nozzle with milk frothing accessory 12a Stainless Steel Tube 12b Plastic A erator tip 13 Document holder pocket 14 Power cord compartment 15 Power on off switch 16 Cup Shelf 17 Removable water reservoir 18 Coffee bean container 19 Grind knob 20 Ground coffee compartment 21 Portafilter Optional 22 Door for accessing infusion unit 23 Ground coffee measuring scoop 24
13. E STRENGTH Y ou may set your preferred coffee strength to three levels Onebean LIGHT about 7 gr ground coffee for Caffe late cappuccino Two bean NORMAL about 9 gr ground coffee for Caf cr me Three bean STRONG about 11 gr ground coffee for Espresso strong coffee 3 1 As soon as the machine is ready for use the factory setting will appear on the display 3 16 repeatedly pressing the selector button 4 the desired strength will appear on the display The selector will cycle through the various strengths as you press it 3 2 SELECTING THE WATER QUANTITY Use the water quantity control knob 3 to determine the quantity of water 3 2 Turn anti clockwise to decrease water quantity 3 2b clockwise to increase water quantity RECOMMENDATION The water quantity of the cup may be altered during the pouring process To determine the ideal water quantity for your taste or cup size proceed as follows when making your first cup of coffee 3 2 Set the water quantity adjustment knob 3 to the following positions To the left for a cup of espresso All the way to the right for a larger cup 3 2 d Press the 1 cup selector 5 The machine will start making coffee 14 3 2 Just before you reach the desired quantity of coffee turn the water quantity control knob 3 anti clockwise slowly to the left until the machine stops dispensing coffee 3 2f Note the position show
14. Filter assembly accessory 25 Water softening filter 26 Litmus paper Weare in accordance with its policy of continuous improvement reserves the right to make any technical and structural modifications without prior notice TABLE OF CONTENTS PLEASE NOTE Maintenance and care 5 please follow these instructions carefully 1 SAFETY INSTRUCTION ann TANNA 1 L OPERA TIONALE START 1 2 1 PREPARING THE COFFEE MACHINE sisisi 1 2 2 ASSEMBLING THE MILK FROTHING ACCESSORY sisisi 9 23 USING YOUR COFFEE MACHINE FOR THE FIRST TIM E uiii 9 PSE TUNG TEMES RUN A A E 11 Cae edo 12 CoB SN CAG ae eee ee 12 3 2 SELECTING THE WATER QUANTITY iiini 13 SE REWINGONE 14 BREWING TWO CUPS OF COFFEE sissi 15 3 5 BREWING WITH PREG ROUND COFFEE isisisi 16 SG DRAWING HOT WATER minane ina 17 3 7 DRAWING STEAM AND FROTHING MILK siisii 17 A PROGRAMMING 19 20 20 y WITHOUT AF UTS 22 24 AAAUTO OFFTIME STAND BY 26 28 a 32 35 CLEANING 39 BUEN SiC
15. For the machine to recognize the presence of the filter you must set the filter setting to On The factory setting is No filter 41a Switch the machine off using button 2 standby mode 4 1 b Press the Service button 7 for about two seconds to enter the programming mode 4 1c The symbols Filter descale Cup Time will come on in sequence 4 1d Wait for the symbol Filter to illuminate on the display and then press the selector button 4 once 41 The symbol ground coffee will start flashing 4 1 Press the selector button 4 until the both symbols Ground coffee B ean start flashing confirming the Filter mode is set ON 4 1g Confirm the selection by pressing the Service button 7 for about two seconds The symbols time filter water tank will now start flashing 41h Remove the water tank 17 and install the filter using the supplied filter assembly tool 23 41i Fill the water tank 17 with cold fresh water to the max mark on the tank and insert it back into the machine The symbol Time wil begin to flash 4 1j Place a recipient under the Hot water Steam nozzle 12 and turn the knob 11 clockwise to the right The system will now perform a brief rinsing cycle to flush out the old unfiltered water 4 1k Wait until the water stops flowing out of the Hot water Steam nozzle 12 and then close the knob 11 anti clockwise to the 0 position 4 11 The following may h
16. Service button 7 for about two seconds The symbol drip tray will begin to flash 5 20 Proceed from point 5 16 as described above in the Cleaning Program section NOTE If you unintentionally start up the cleaning program you can interrupt it at the beginning of the cycle by pressing the On Off button 2 for about 2 seconds 35 5 2 LIME SCALE REMOVAL IMPORTANT When the machine requires lime scale removal the symbol Descale will appear on the display and the service button 7 will flash e f you do not use the optional filter 25 regularly it is essential to remove lime scale in the appliance at least once every two months so as not to compromise the functioning of the appliance with time e NOTE Never use sulphuric acid or any other product containing this acid as it may compromise the functioning of the appliance Do not use vinegar or vinegar based products for lime scale removal Do not use any substance not authorized by the manufacturer use only special X presso Lime Scale Remover descaling tablets or the Lime O Powder available from X presso Direct 66 2 906 8118 e NOTE Y ou may continue making coffee hot water and steam but we recommend you run the lime scale removal procedure promptly e Important Do not interrupt the lime scale removal program once it has started If you unintentionally start up the lime scale removal program you can interrupt the procedure at the start of the cycle by p
17. al filter program does not work ERROR 1 ERROR 2 ERROR 3 Filter programmed as ES The illuminated rind on the ON OFF button 2 is flashing The appliance is too cold The illuminated ring on the ON OFF button 2 is flashing The appliance has not Heated to the operating temperature The illuminated ring on the ON OFF button 2 is flashing The boiler unit is obstructed or incorrectly installed 43 Program the to NO Let the machine warm up at room temperature for one or two hours Let the machine warm up at room temperature for one or two hours Call our service centre 44 9 0LIMITED ONE YEAR WARRANTY This limited warranty covers your new A 400 This warranty is in effect for the period and usage described above from the date of the first purchase TRANSPORT when sending the machine use original packaging materials the inner and outer cartons or use approximately 2 of bubble wrap and secure the machine properly Any damage in transit is NOT covered by this warranty This warranty does not cover e Any machine not distributed by X PRESSO e Any machine not purchased from an authorized dealer e Damage cause by accident abuse negligence misuse improper operation or failure to follow instructions contained in this manual The machine is plugging into an unsuitable power voltage or short circuited due to water spillage e Any service or altera
18. and that the power outlet is connected to earth e Always turn off the appliance at the on off switch before unplugging it Donotpull the power cord out of the socket but grasp the plug itself to avoid damage to the socket e Do notallow the power cord to be twisted crushed stretched or come into contact with sharp or hot surfaces e Do not use the appliance if the power cable or other important parts are damaged e Do not use electric extension leads that are not authorized by the manufacturer as they may Cause damage or fire f itis necessary to replace the power supply cable please refer to the nearest our authorized service centre since the use of a special tool is necessary e Do not use the appliance near a bathtub shower or container full of water Never immerse the appliance the cable or the plugs in water or any other liquid Use of the appliance in places where there is a danger of explosions is prohibited Do not use the product with toxic substances Do not lay the hot appliance on surfaces sensitive to heat Do not leave the appliance exposed to wind or rain Do not place the appliance near live element an electric stove or any other source of heat Do not expose the appliance to extreme temperatures Never let children or people who are not familiar with how the appliance works use it Do not press the buttons hard or with a pointed object such as pen Always rest the appliance on a stable surface In cas
19. appen next e Thesystem quickly heats up and is ready for use again e The Service button 7 may carry on flashing If this happens press the butt 7 once to conduct another short rinse cycle through the coffee outlets 8 4 1m Thesystem will now be ready for filtered water use NOTE e cannot use both of these settings at the same time e The optional filter loses its effectiveness after about 50 liters of water e f the machine has not been in use very much the filter must still be replaced after a maximum of two months even if no indication appears on the display e Asareminder set the replacement date on the wheel on the top of the filter IMPORTANT The system must be programmed in either of the two modes 21 on 22 e Foruse with the optional Water Softening Filter 25 follow 4 1 above e Thehardness of the water must be set and therefore the Lime Scale removal cycle will be required e For more thorough prevention of lime scale build up it is advised to run the lime scale removal program at least once a year even if you regularly use the optional water softening filter Y WITHOUT A FILTER Setting the filter mode to OFF Ground coffee If the optional Filter mode shall no longer be in use the system must be reprogrammed for the setting Filter mode OFF 41n Switch the machine off using button 2 standby mode 4 10 Press the Service button 7 for about two seconds to enter the progra
20. as been completed automatically by the machine 2 3f The machine is now ready for use e RECOMMENDATION Place dish underneath the coffee dispensing nozzle 8 to collect water from the service rinse e You may rinse out the machine at any time during regular operation by pressing the service button 7 letting water flow through the coffee outlet 8 24 SETTING THE GRIND IMPORTANT The grinder may only be adjusted when the coffee grinder is in operation grinding coffee beans 2 4a The coffee grinder may be adapted to suit the roast of the coffee We recommend the medium setting for all roasts 2 4b Open the coffee bean container 18 lid 2 4 With the coffee grinder in operation turn the knob 19 to the desired position The smaller the dot next to the knob 19 the finer the grind Remember lightly roasted coffee usually requires a finer grind dark roasted coffee usually requires a coarser grind 3 PREPARATION NOTES e This machine has been pre tested ready to make its first cup of coffee We recommend that you re program the main settings to suit your individual preferences First of all follow the steps listed under the Programming heading to adjust the filter and water hardness settings e When using the appliance for the first time or if the appliance has not been used for some time the first coffee you make will not have perfect aroma and should be discarded 3 1 SELECTING COFFE
21. e of accidental fall of the appliance it is necessary to have it checked by an authorized service centre as the internal safety features may have been affected In case of breakdown or malfunction switch off the appliance and never attempt to disassemble it but refer to an authorized service centre In order to avoid prejudicing the safety of the appliance use only original spare parts and accessories approved by the manufacturer Do not wind the power cord around the appliance especially when the appliance is still hot Position the machine on a horizontal surface Do not use lime scale removers which are not authorized by the manufacturer Check that there is water in the reservoir before turning on the machine Always fill the water reservoir with cold clean water Do not use milk or any other liquid Do not use the appliance if the drip tray and the grill are not in place Do not wash coffee machine accessories in the dishwasher Do not direct the steam jet at electrical appliances Let the appliance cool down before cleaning the hot water nozzle Danger of burns Never place your hands inside the jet of steam Danger of burns Do not direct the steam jet at people animals or debris Never use beans treated with additives such as sugar or similar substances USEFUL INFORMATION CHOOSING COFFEE True espresso coffee is recognizable by its dark colour typical cr me and rich flavor The flavor and aroma of a coffee bean are
22. hine 5 2 The machine will perform a brief rinsing cycle when the rinse has completed the symbol tablet will appear on the display RECOMMENDATION Place a dish of Sufficient capacity about 0 5 liters under the coffee dispensing nozzle 8 5 2 the Ground coffee compartment 20 and insert ONE X presso Cleaning tablet Close the lid The Service button 7 will begin to flash IMPORTANT Do not put the Cleaning tablet in the water reservoir 17 5 2 Press the service button 7 5 2g machine will now begin the cleaning procedure This procedure is automatic and takes approximately 10 minutes 5 2h When the cleaning cycle has been completed the symbol Drip tray will appear on the display 34 5 21 Remove and empty the drip tray 9 Replace the drip tray 9 into the machine If necessary fill the Water Reservoir 17 with fresh cold water 52 machine quickly heats up to the right temperature and is ready for regular use again MANUAL CLEANING If necessary you can run the cleaning program at any time even if the alarm does not appear on the display 5 2 Switch the machine ON using button 2 Operating mode 5 21 Press the Service button 7 for about two seconds The symbols tablet filter andor Descale will begin to flash in sequence 5 2m Wait until the symbol tablet displays and press the Service button 7 once briefly to confirm Press the
23. hing of the service button 7 RECOMMENDATION Press the service button 7 only when you want to replace the filter Y ou may continue making coffee hot water and steam but we recommend you replace the filter promptly 5 0a Switch the machine off using button 2 standby mode 5 0b Press the Service button 7 for about two seconds to enter the programming mode 5 0c Remove the water tank 17 and install the replacement filter using the supplied filter assembly tool 23 504 Fill the water tank 17 with cold fresh water to the max mark on the tank and insert it back into the machine The symbol Time will begin to flash 29 5 0e Place a recipient under the Hot water Steam nozzle 12 and turn the knob 11 clockwise to the right The system will now perform a brief rinsing cycle to flush out the old unfiltered water 5 0f Wait until the water stops flowing out of the Hot water Steam nozzle 12 and then close the knob 11 anti clockwise to the 0 position 5 0g The following may happen next e Thesystem quickly heats up and is ready for use again e The Service button 7 may carry on flashing If this happens press the button 7 once to conduct another short rinse cycle through the coffee outlets 8 this is normal 5 0 The system will now be ready for filtered water use 30 MANUAL FILTER REPLACEMENT Even if you make coffee infrequently the optional filter must be replaced at least every 2
24. ing keeping the packaging for possible future transporting and storing 2 1b Remove the water reservoir 17 and rinse it with clean cold water 210 Fill the water reservoir with clean cold water no higher than the MAX mark Important Do not use sparkling water or any other liquid 2 10 Place the water reservoir correctly back into the machine and close the lid 2 1e Open the lid of the coffee bean container 18 fill it with suitable coffee beans and close the lid again Do not use coffee beans which have been treated with sugar or other additives during or after roasting as they could damage the coffee grinder Important Repair costs due to such damage will not be covered by the warranty Powering up 219 Remove the power cord from the cord compartment 14 and plug it into suitable outlet For information see items 6 M ains AC operation 2 1g Press the power switch 15 On The on off button 2 will illuminate 21h Press the on off button 2 The symbol CUP will flash on the display while the system is heating up for approximately 45 seconds 2 11 the machine has heated up to the correct temperature the Service button 7 will start flashing 2 1j Press the Service button 7 to rinse the system out through the coffee dispensing nozzle 8 Important This rinsing step cannot be left out as no other function will operate until this cycle has been completed automatically by the machine 21k
25. ision or instruction concerning the use of the appliance by a person responsible for their safety
26. mming mode 4 1p The symbols Filter descale Cup Time will come on in sequence 4 1 q Wait fr the symbol Filter to illuminate on the display and then press the selector button 4 once 4 1r The symbol ground coffee Bean will start flashing 41 Press the selector button 4 until only the symbol Ground coffee will be flashing confirming the Filter mode is set OFF 23 4 1t Confirm the selection by pressing the Service button 7 for about two seconds The system will now go back to the Off Stand by mode to conclude the programming 4 2 WATER HARDNESS NOTE The frequency of lime scale removal cycles depends on the hardness of the local water Supply Set water hardness correctly as soon as you begin using the machine so that the system will be able to inform you when a lime scale procedure is required 4 2a Thefirst step is to test the water using the supplied litmus paper 26 Fill a small container with tap water Dip the litmus paper into it and remove it immediately then shake it gently 420 After about one minute you will be able to read the results by counting the red dots as described below e dot 1 7 d H 1 12 6 fH e 2 red dots 8 14 d H 12 7 25 2 TH e 3 red dots 15 21 d H 25 3 37 8 FH e dots gt 21 d H gt 37 8 fH The factory setting corresponds to LEVEL 3 4 2 Switch the machine off using button 2 standby mode 42d Press the Service button 7 for about tw
27. n on the dots appearing on the water quantity adjustment Knob 3 3 3 BREWING ONE CUP OF COFFEE 3 3 Place a pre heated cup underneath the coffee dispensing nozzle 8 3 3b The height of the coffee dispensing nozzle 8 may be adjusted precisely to suit the cup size 3 3 Set the desired coffee strength and water quantity as in 3 1 and 3 2 3 3 Press the 1 cup selector 5 33 Atthis point the machine will begin the infusion procedure 339 The procedure may be interrupted at any time by pressing the 1 cup 5 or 2 cup selector 6 Important If making coffee for the first time the grinding chamber may still be empty The symbol beans flashing may appear on the display 1 and the machine will stop the procedure If this happens press the 1 cup selector 5 again to restart the procedure This may be required a second time BREWING TWO CUPS OF COFFEE Note Two grinds will automatically be performed to make two cups of coffee 34 Place both cups under the coffee dispensing nozzle 8 3 46 The height of the coffee dispensing nozzle 8 may be adjusted precisely to suit the cup size 3 4 Set the desired coffee strength and water quantity for one cup as in 3 1 and 3 2 above 3 4d the 2 cup selector 6 3 4e Atthis point the machine begins the infusion procedure and makes two cups of coffeein a row 3 4f The procedure may be interrupted at any time by pressing the 1 5 or
28. o seconds to enter the programming mode 24 4 2e The symbols Filter Water Hardness Cup Time will come on in sequence 4 2 Wait for the symbol Water Hardness to illuminate on the display and then press the selector button 4 once NOTE It will appear only if the Filter is programmed to OFF 4 2g The factory setting LEVEL 3 will display 4 2h the selector button again 4 until the level of water hardness determined by the litmus paper test appears on the display 4 2i Confirm the selection by pressing the Service button 7 for about two seconds Programming is complete and the system returns to the Off Standby mode 4 3 CUP TEMPERATURE Y ou may change the temperature of the coffee to suit your preferences NORMAL LEVEL1 HIGH LEVEL2 MAXIMUM LEVEL3 NOTE The factory setting is HIGH LEVEL 2 43a Switch the machine off using button 2 standby mode 4 3 0 Press the Service button 7 for about two seconds to enter the programming mode 43c The symbols Filter Water Hardness Cup Time will come on in sequence 25 43d Wait for the symbol Cup T to illuminate on the display and then press the selector button 4 once 43 The factory default setting HIGH LEVEL 2 will display 4 3f Press the selector button again 4 repeatedly until the desired cup temperature symbols appears on the display 4 3g Confirm the new selection by pressing the Service button 7 for about two seconds
29. r coffee grounds container 9c is absent or has not been installed correctly The contacts 9d on the drip tray are dirty Overheated system The machine needs cleaning There are lime scale deposits in the machine Filter has expired The door of the boiler unit 22 is open Empty the tray Insert the drip tray and coffe grounds container Clean the contacts Cool down the system when producing hot water Run the cleaning program Run the lime scale removal program Replace filter Close the door 8 TROUBLESHOOTING PROBLEM The machine produces neither hot water nor steam Insufficient froth The machine produces only afew drops of coffee The coffee has no cream The grinding motor is very noisy MEANING Nozzle 12 is blocked Unsuitable milk Y ou are using too fine a grind Y ou are using coffee which is too finely ground The type of coffee you are using is not appropriate Y our coffee beans are not freshly roasted The grind you are using is not appropriate for the type of coffee Foreign body such as a pebble is in the grinding motor 42 SOLUTION Clean nozzle thoroughly Use cold milk with alow fat content Change the fineness of the ground Use more coarsely ground coffee Change the type of coffee used Use fresh coffee beans A djust the grind Contact the service centre Y ou may continue to use the machine with pre ground coffee The lime scale remov
30. ressing the On Off button 2 for about 2 seconds 36 5 Pressthe Service button 7 for abouttwo seconds The symbol crip tray will begin to fash 5 2b Remove the drip tray 9 Clean it thoroughly using only water and replace the drip tray into the machine 5 2 The Symbol Water tank will flash on the display Remove the W ater Reservoir 17 and put the special X presso Lime Scale Remover descaling tablets or the L ime 0 Powder into the corresponding liter of water ensuring it has dissolved completely Important Do not put lime scale remover into the ground coffee compartment 20 This isnot the Cleaning Cycle 5 2d Put the reservoir back into the machine The symbol TURN VALVE will appear on the display 5 2 Place a container of sufficient size about liter under the hot water nozzle 12 5 2 the steam hot water knob 11 clockwise to the right 5 2g The machine begins the automatic process The lime scale remover solution will intermittently flow out of the nozzle 12 for about 10 minutes The symbol NOZZLES flashes during the entire procedure 52h When the symbol TURN VALVE will appear on the display turn the steamy hot water knob 11 anti clockwise to the left back to the 0 position 37 5 21 Atthis point the lime scale removal solution will now flow into the drip tray for about 15 minutes 5 2 When the lime scale remover solution has flowed out of the outlets symbols
31. the nozzle by the black plastic part NOTE Residues left on the nozzle after frothing milk hard to remove when dry so itis a good idea to clean the whole assembly as soon as it cools down Eliminate milk residues in the holes through which milk passes by rinsing it out with hot water immediately after use TIP Itis important to rinse the machine through before making coffee again to cool down the Circuit or the aroma of the coffee will be spoiled Place a container under the coffee dispensing nozzle 8 and press the service button 7 and or let a little hot water flow through the nozzle 12 4 PROGRAMMING Use the following buttons for the programming functions e Service Button 7 program mode Confirmation button e Selector knob 4 selection button e On Off Button 2 Stop Cancel Programming The machine allows you to set the following functions 1 Filter M ode optional 2 Water hardness setting 3 Coffee cup Temperature 4 Automatic Off Time 20 4 1 FILTER optional y WITHA FILTER Setting the filter mode to ON Ground coffee ean The machine can be supplied with a special optional filter accessory for the water reservoir The filter consists of resins and protects the machine from lime scale deposits It can filter out many substances such as chlorine and metallic residues all of which can alter the flavor and aroma of coffees while leaving the mineral content of the water unaltered
32. tions performed by and unauthorized person company or association e Damage caused by neglecting and omitting maintenance cleaning and decalcifying e Damaged caused by ingredients not allowed in this product e Damage to the Stainless Steel carafe due to improper use 45 46 Other limitations and exclusions Any implied warranties including fitness for use and merchantability are limited in duration to the period of the express warranty set forth above and no person is authorized to assume for EPRESSO and other liability in connection with the sale of the machine EPRESSO expressly disclaims liability for incidental and consequential damages cause by the machine The terms Incidental damages refer to the loss of the original purchaser s time loss of the use of the machine or other costs relating to the care and the custody of the machine The terms consequential damages refer to the cost of repairing or replacing other property with is damaged when this machine does not work property Any loss of income is excluded The remedies provided under this warranty are exclude and in lieu of all others This warranty gives you specific legal rights and you may also have other rights which vary from Province to Province IMPORTANT This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and Knowledge unless they have been given initial superv
Download Pdf Manuals
Related Search