Read product User Manual
Contents
1. Windows 95 98 2000 ME NT4 0 XP PHYSICAL Dimensions 180 mm W x 200 mm H x 380 mm D 7 1 W x7 9 H x 15 D 180 mm W x 200 mm H x 450 mm D 7 1 W x 7 9 H x 17 7 D 180 mm W x 200 mm H x 510 mm D 7 1 W x 7 9 H x 20 1 D Net Gross Weight 15 kgs 16 kgs 33 0 Ibs 35 2lbs 21 kgs 22 kgs 46 2 lbs 48 4lbs 25 kgs 26 kgs 55 0 lbs 57 2lbs ENVIRONMENTAL Ambient 32 104 F 30 90 RH Non Condensing Audible Noise Less than 45 dBA 1 Meter Measured CE FC Oum 10 Installation amp Operation Instructions To install the UPS please follow the installation steps below and Charge the UPS overnight before use 1 Check the power ratings on the back of your UPS to make sure the input voltage matches with your local power specifications 2 Plug the female end of the enclosed AC power cord into the male AC power inlet on the back of your UPS 3 Decide where you want to place your UPS It is recommended that you place it in a location where you will be able to see and hear its visual and audible indicators and alarms 4 Plug the male end of the same AC power cord into a properly grounded AC wall outlet 5 Plug in your computer devices into the output sockets Make sure you have charged your S series UPS overnight before using the UPS for the very first time 6 Turn on your computer and or other conne2. Fer Line interactive UPS User s Manual S1000A S 1000E S 1500A S 1500E S 2000A S 2000E 1000VA 1500VA and 2000VA Table of Contents Important Safety Introduction eceeee eee 1 Features of Line interactive UPS 3 Overview S1000 1500 2000 VA eee 6 Product Specification v4 ic2ccs becescseevieniaeeiuewcnceee 9 Installation amp Operation Instructions 4 11 Audible Visual Indicators cece eee ee eens eee 14 Software Application 0 ceeceeeeeee rene no eetees 17 Limited Warranty 0 2 ebicnecseis eb seene crete enw oteesd 19 Troubleshooting 2scoc 5220 se ceo eke eee 22 Introduction IMSUUGTIONS utente Battery management should be performed or supervised by personnel knowledgeable of batteries and with required precautions Keep unauthorized personnel away from batteries When replacing batteries replace with the same type of batteries UPS is designed for use with computers and monitors network system and electronic cash register systems Other application is not suggested CAUTION Do not dispose of battery or batteries in a fire The battery may explode CAUTION Do not open or mutilate the battery or batteries Released electrolyte is harmful to skin and eyes It may be toxic CAUTION A battery can present a risk if operated at electrical shock and high short circuit current The following precautions should be
3. give you specific legal rights You may also have other rights which vary from state to state 19 WHEN YOU RETURN A UPS PRODUCT OR BATTERY UNDER THIS WARRANTY you must first obtain an RMA number by calling Fenton UPS Fenton UPS reserves the right to request that you submit a letter describing the circumstances under which the problem occurred and that you submit any other supporting evidence and documentation Return product with freight prepaid for RMA service Equipment Protection Policy Fenton UPS warrants to the original purchaser of this Fenton product for the functional lifetime of the product that if a power disturbance damages electronic equipment while properly connected to this product the electronic equipment will be repaired replaced or reimbursed at fair market value at Fenton UPS option by Fenton UPS ata cost of up to but not exceeding 20 000 Fenton UPS reserves the right of ownership of the damaged equipment if it is replaced or reimbursed This Policy applies only to power line and telephone line transients such as spikes and surges and only if the electronic equipment is plugged into outlets that are properly wired and grounded and if primary protection devices are installed with the utility power and telephone service equipment This Policy does not apply to cable TV transients unless such protection is specifically stated as being offered by a Fenton product and proper grounding is maintained with the cable TV
4. service This Policy applies only to UL cUL CSA or CE listed electronic equipment This Policy does not cover damage caused by natural disasters and accidents including lightening This Policy does not cover the cost of lost data lost time or damaged software and Fenton UPS shall in no way be liable for any other damages costs expenses or loss of revenue or profits resulting from occurrences not covered by this Policy YOU MUST REGISTER YOUR FENTON PRODUCT BY REGISTED AT www fentonups com WITHIN TWO WEEKS OF PURCHASE IN ORDER FOR THIS POLICY TO BE VALID 20 This protection guarantee is not an insurance policy This guarantee is not a substitute of insurance coverage policy provided by your insurance carrier and equipment warranty First you need to make the claim for recovery including but not limited to a claim under any applicable insurance other warranty or extended warranty IF YOU MAKE A CLAIM FOR DAMAGE TO YOUR ELECTRONIC EQUIPMENT you must first obtain an RMA number by contact Fenton UPS within one week of the occurrence of the damage After receiving your RMA number you must then 1 submit a letter describing the circumstances under which the damage occurred 2 enclose all other supporting evidence or documentation that exists 3 submit the original receipt or proof of purchase 4 return the Fenton product in question to Fenton UPS freight prepaid by United Parcel Service Fenton UPS reserves the right to determin
5. Network Line Protection Two special jacks allow RJ 45 connection to protect your Internet Modem or 10Base T signals from surge damage Smart Overload Protection While the UPS is on the S series UPS smart chip monitors load conditions In case an overload or short circuit occurs your UPS will beep continuously to alarm or shut down automatically to save your critical load and avoid the nuisance fuse blows Introduction Features of Line interactive UPS Real Time Warning For Failed Battery LCD Model The battery self test function of the UPS will check battery status every 20 minutes no need to push the button by user The Battery Replacement symbol on LCD panel will show up when battery failed or is in open circuit simultaneously the word Battery Bad will be displayed in the main screen of the monitoring software Overview S1000 1500 2000VA LED type Front panel LUNN eA DC START Battery level SELF TEST O 100 ALARM RESET O80 KUP CEETET LOW BATT OVER LOAD 1 LEDs of battery voltage level and load level 2 LED of operation status 3 Control button XLED indication Please refer to audible visual indicator section LCD type Front panel E ACout AC in BATT COD TEMP wee TIMER Oo POWER ON OFF SELF TEST Loy ALARM RESET By pass 1 Main control button 2 LCD screen 3 Selection button for mode amp value Note LCD ava
6. allation amp Operation Instructions 11 Pushing the button for 4 seconds the UPS will turn off the power on the outlets But the UPS will keep charging if AC power is normal To stop the charging please pull out the power cord to shut down the UPS completely 12 During a blackout push the button for entering idle mode then push again for one second and the UPS will be turned on and enter into backup mode To turn off the power from UPS please push the button for 4 seconds then the status LED in LED version will blink orange every 2 seconds or LCD display will show OFF in LCD version then wait for 5 seconds and UPS will turn off the power automatically 13 In the idle mode UPS will turn off power automatically within 4 seconds during a utility failure while UPS will keep charging the batteries if the utility power is normal When utility power is normal please pull out the power cord if you want to turn off the UPS completely Green power mode setting When Green Power function is enabled the UPS will turn off the power within 30 seconds after blackout occurs with power consumption lower than 25W Audible Visual Indicators Under the following power conditions status the LED and LCD type indicator and the audible alarm will respond as follows LED indicator table l Conditions LED Indicator Audible Alarm l Status Description Status Description idle mode Util
7. anced Intelligent UPS management utility which can communicate with S series UPS through the RS 232 or USB interface With UPSilon 2000 users can manage UPS easily UPSilon 2000 will display in analog signals and picture the input output voltage frequency load temperature battery voltage and other power events to monitor power quality It can also monitor remote UPS with the use of the intranet internet Using UPSilon 2000 there will be no distance problem Itmakes work efficiently When there is a system power failure or battery low UPSilon 2000 can automatically save files and shutdown systems plus sending out warning messages via email Users shall respond accordingly to avoid problems with the system and data at system power failure Software Application Operating System Supported eNovell Netware eWindows 95 98 NT 2000 ME XP eFreeBSD eLinux Please install the UPSilon 2000 step by step as follow 1 Turn off the computer 2 Connect the UPS output to the computer input power socket 3 Connect the special RS232 cable or special USB cable between the UPS and the computer 4 Turn on the UPS 5 Turn on the computer 6 Put the UPSilon2000 setup CD in CD ROM 7 Select install program then select the appropriate install program for your computer operating system and follow the operating system instruction Limited Warranty Please register your Fenton product on http www fentonups com Fenton UPS prov
8. cted devices Installation amp Operation Instructions 7 Perform the Power Failure Test Pull out the AC power cord from the wall receptacle to test the operation of UPS on battery backup function Make sure that your computer and other devices are running normally Turn Off the UPS Before you turn off the UPS power please make sure that your computer and other devices are properly shut down Push the Power Switch to turn off the UPS fee Ko To ensure your computer equipment to be protected during an AC utility power failure it is important to make sure that the maximum power needed by the equipment is not over the rated capacity of the UPS If your equipment is overloading the UPS then the red LED will light up LED version or the Over load symbol will show up LCD version and the alarm will beep Furthermore if the overload is severe the UPS will shut down immediately for protecting UPS itself 10 After installed under the AC mode the UPS will charge the battery automatically and the status LED in LED version blinks green every 2 seconds or in LCD version the battery symbol and battery level will blink every second during charging If AC auto turn on function is enabled the UPS will turn on automatically when utility power is green If auto turn on is disabled please push the button for one second on the front panel then the UPS will supply power to the outlets after a short time of self test Inst
9. e whether the damage to your equipment was caused by a performance failure of a Fenton product covered by this Policy and reserves the right to request that damaged equipment be sent to Fenton UPS at the owner s expenses for inspection Furthermore Fenton UPS reserves the right to contact the authorized service center that repairs the equipment Unauthorized service may void this policy If Fenton UPS determines in good faith that the damage to your equipment was caused by a covered performance failure of a Fenton product covered by this Policy you will be compensated as stated above In order for this Policy to apply all conditions as stated above must be met and you must have the original receipt or proof of purchase 21 Troubleshooting Trouble Shooting Guide Table Problem UPS no reaction while AC Possible Cause Action to Take is connected Power outputis normal UPS emits continuous beep status LED shows RED or LCD shows overload 1 Power cord plug is loose 2 Fuse on rear panel blown Inside the drawer of inlet 3 Dead wall socket UPS is over loaded 2 Replace fuse 3 Check wall socket with a table lamp Tum off UPS and unplug excessive loads from UPS No power on outlets UPS emits continuous beep status LED show RED or LCD shows over load UPS has shut down due to severe overload Unplug excessive loads from UPS press button to reset the buzzer and tum on the UPS agai
10. ery The battery has failed and must be replaced 12 replacement The battery is checked each time the Test lt Function is executed co Battery voltage 1 The higher the battery voltage the more bars Co level will illuminate 13 2 When the UPS is charging the battery the Oo battery symbol and the level indicator will blink together Mode Value Description AC out V AC output voltage AC in V AC input voltage AC out Hz AC output frequency BATT V DC battery voltage TEMP C UPS internal temperature The UPS will turn off when the displayed value f reaches zero For example if the timer shows TIMER Min to off 0 5 Min to off the UPS will shut down in 30 14 seconds The UPS wil tum on when the displayed value TIMER Hr to on reaches zero For example if the timer shows 48 Hr to on the UPS will tum on in 2 days The estimated remaining run time in Back up BATT Min to off mode The accuracy of the value is influenced by the loading type ambient temperature and battery condition old or new Selection Buttons for modes amp values All the operation data will be displayed on LCD screen By selecting the required mode upward or downward the related value will be displayed 16 Software Application UPS Software Introduction Introduction The S series UPS with software driver provides the functions of AC failure detection UPS battery low detection and system shutdown UPSilon software is an adv
11. ides the owner of this Fenton product with the following Warranties and Equipment P rotection Policy One Years UPS Warranty Fenton UPS warrants to the original purchaser of this Fenton product that the product is free from defects in original materials and workmanship for a period of up to one year from the date of initial purchase This warranty is only valid if the product has been properly installed and is used in the way for which it is intended and has received only factory authorized repairs servicing or alterations Under warranty products that meet these conditions and that function improperly will be repaired or replaced at the discretion of Fenton UPS One Year Battery Warranty Fenton UPS warrants to the original purchaser of this Fenton product that the original batteries contained within this product will function for a period of one year This warranty is only valid if the product has been properly installed and is used in the way of which it is intended and has received only factory authorized repairs servicing or alterations Under warranty batteries that meet these conditions and that function improperly will be repaired or replaced at the discretion of Fenton UPS These warranties contain the sole express warranty of Fenton UPS which makes no other warranties expressed or implied These warranties are made in lieu of any implied warranties of merchantability or fitness for a particular purpose These warranties
12. ilable models All of S series sine wave line interactive UPS could be equipped with LCD display These models include standard tower series long run tower series standard rack mount series amp long run rack mount series etc XLCD indication Please refer to audible visual indicator section Rear panel a 5 0 a 0 NEMA Type O RO A WNE i IEC Type 1000 IEC Type 5 1500 5 2000 i Fuse Inlet of AC power Outlet s NE MA IE C RS 232 Communication Port It provides RS 232 serial signal and contact closure signals Network J ack RJ 45 These two modular jacks provide surge protection to modem or 10 Base T signals Battery Connector When use external battery the load has to be lower than 1 4 of rated full load Outlet s NE MA IEC DIP switch Available for standard models 1500 2000 long run models 1000 1500 2000 DIP Switch BARES 12 3 4 DIP 1 DIP 2 220V System 110V System Down Up 220V 60Hz 100V 50Hz Up Up 220V 50Hz 110V 60Hz Up Down 230V 50Hz 115V 60Hz Down Down 240V 50Hz 120V 60Hz DIP 3 for AC auto turn on when AC power returns UP Enable Down Disable DIP 4 for Green Mode setting UP Enable Do
13. ity Good Green Flashing Off None Utilty outage Orange Flashing Off None Timer on Red _ Flashing Off None Normal Normal Green Flashing Off None Back up Utility good mode rae No Orange Flashing Beeping 4 Sec time oa Back up Orange Flashing Beeping 42Sec time Loaded BatteryLow Orange Flashing Beeping 4 Sec time Battery NG Flashing Beeping 8 Sec time Over load Flashing Beeping Continuous UPS fault Flashing Beeping 2 Sec 32 time Thermal alam Flashing Beeping 2 Sec 32 time 14 Symbol LCD indicator table 1 Indication Description Over load The loading exceeds the rating of UPS Load level The higher the loading is the more bars will illuminate Sad UPS is loaded When Green Mode is enabled this symbol will display if the loading is over 30W approximately and disappears when its under 25W approximately If Green Mode is disabled the symbol will always display gt Normal mode 1 The sine wave symbol will display steadily without battery symbol when UPS is in the normal mode Battery mode 1 The sine wave symbol and battery symbol will blink when the UPS is in back up inverter mode Test mode 1 The sine wave symbol will display steadily with blinking battery symbol when the UPS is in testing mode Buck mode The AVR Auto Voltage Regulator is reducing the output voltage of the UPS when
14. n UPS does not provide expected run time 1 Excessive loads connected at UPS s outlets 2 Battery is weak and cannot provide enough capacity Do not operate the UPS with load and leave the UPS plugged in for 10 hours Then testitagain if UPS still cannot provide expected run time battery should be replaced Button on front panel doesn t work 1 The CPU inside UPS is not running correctly 2 Button damaged 1 Push the button for 10 seconds to reset the UPS 2 Unplug power cord and all loads from the UPS to letit shut down automatically and call for service When push button for testing under AC mode UPS emits urgent beep 8 beeps per sec and RED LED blinks or LCD display shows battery replacement at the same time Battery is weak and should be replaced Replace batteries UPS can not be tumed on 1 Battery polarity wrong 2 UPS fault 22 1 Check battery connection 2 Call for service 1000 s any question please contact us at the following Metapo Inc 2380 Qume Drive Suite D San ose CA 95131 USA Tel 408 943 9308 Fax 408 943 9309 Website www metapo com www fentonups com Email support metapo com Appendix AS FOR SOFTWARE APPLICATION YOU RE SUGGESTED TO REFER TO THE WEB SITE HEREUNDER WWW MEGATEC COM TW 23
15. sing S series Line interactive UPS This series UPS is an advanced Line Interactive Uninterruptible Power System which produces power in pure sine wave form to your equipment unlike the traditional off line UPS this series requires very short transference when blackouts happen The voltage regulation of the series is similar to On line UPS however the series provides efficiency over 98 under normal power condition Two charge modes quick charge and trickle charge are provided to maintain the batteries at the best condition Battery Replacement Warning The self test function by pushing the button will inform you with an alarm when the batteries are weak and require replacement Smart Communication Interface A communication interface port is provided for sensing input voltage output voltage battery capacity output power level and UPS statuses Through this port you can remotely control the UPS such as turning on and off by customized schedule and setting the auto test procedure Introduction Features of Line interactive UPS Automatic Voltage Regulation Function AVR provides voltage range by input 22 and output 5 regulation which depend on two boosts and two bucks design DC Start Function Allow you to power on the UPS inverter battery operation even in absence of external power This function offers you the convenience of powering on your computer via UPS when the AC utility power is out
16. taken before working on batteries 1 Remove watches rings or other metal objects 2 Use tools with insulated handles CAUTION This UPS cannot be laid flat UNAUTHORIZED SERVICING OF YOUR UPS OR FAILURE TO FOLLOW THESE INSTRUCTIONS WILL CAUSE YOUR WARRANTY TO BE NULL AND VOID Introduction INStrUCTIONS ccc cee vee p If your UPS shows obvious signs of having been damaged during transport immediately return the unit in its original box with your receipt to your dealer for replacement p Keep your UPS away from wet or moist places p Do notleave your UPS in direct sunlight p Check the electrical specifications on the back of your UPS to make sure that the input voltage matches your local power specifications p Your UPS is designed for use with computers and monitors network system and electronic cash register systems Other applications are not suggested p To Clean the external surfaces of your UPS use dry cloth only since water or cleaning solutions could get into the internal electronic circuitry then cause major damage Do not apply any chemical solvents to the UPS p Your UPS is intended for use in a climate controlled indoor area not outdoors or exposed to severe climate conditions p UNAUTHORIZED SERVICING OF YOUR UPS OR FAILURE TO FOLLOW THESE INSTRUCTIONS WILL CAUSE YOUR WARRANTY TO BE NULL AND VOID Introduction Features of Line interactive UPS Thank you for purcha
17. the input voltage is too high and the sine wave symbol as mentioned in item 4 will also display steadily to indicate that the outputis in the normal mode Boost mode The AVR is increasing the output voltage of the UPS when the input voltage is too low and the sine wave symbol as mentioned in item 4 will display to indicate it s in the normal mode Timer is enabled This symbol will show up in the following situations 1 A tum on tum off schedule has been set using the monitoring software 2 The Green Mode is enabled and the loading is under 25W approximately The UPS will tum itself off automatically in 30 seconds HIGH Thermal alarm The temperature inside the UPS is over 55 C If the user does not reduce the load the temperature will continue to rise and the UPS will shut down automatically at 60 C 15 LCD indicator table 2 Indication Description Silence mode The audible alarm has been silenced To reset 9 Va the alarm in Back up mode push the control button not available during low battery level or abnormal condition UPS fault The UPS has failed and must be repaired 10 a Contact a qualified service person eat Battery normal 1 In normal operation this symbol indicates a charged battery ea u B attery low 1 When the battery charge level is low the word LOW LOW will be added to the symbol pet Batt
18. wn Disable P S Program setting active only after the UPS is re started 8 Product Specification ITEM DESCRIPTION MODEL 1000 1500 S2000 RATING 1000VA 1500VA 2000VA WATTAGE 600W 900W 1200W 100 110 115 120 or 200 220 230 240 Voltage Vac 22 Nominal INPUT Frequency 50 60Hz 5 Auto Sensing Phase Single Volt 100 110 115 120 or 200 220 230 240 oltage Vac 3 On Backup Mode Frequency 50 60 Hz 40 1 Auto Sensing Waveform Type OUTPUT RN 5 On AC Power Mode Transfer Time Pure Sine Wave 3 5 ms Typical Number of 3 IEC Type Outlets Si 5 e 2 NEMA Type Energy SURGE Rating 320 J oules Instantaneous PROTECTION Dataline RJ 45 Modem 10 Base T Signals Protection Banery Maintenance Free Lead Acid Type Re Charge 5 Hours To Time 90 Charged 3 Hours To 90 Charged BATTERIES Battery 12V 7AH x2 12V 7AHx3 12V 7AH x4 Capacity Typical 15 33 Minutes 13 33 Minutes 13 44 Minute Backup Base On The Base On The Base On Th Time Loading Loading Loading Product Specification ITEM DESCRIPTION 1500 2000 COMMUNICATIONS amp MANAGEMENT Interface Port RS 232 Control Panel LED Status Display On AC Power On Battery Overload Audible Alarm On Battery Low Battery Overload S oftware OS Support UPSilon2000
Download Pdf Manuals
Related Search