HIGH SPEED DOME CAMERA USER`S MANUAL
Contents
1. lt PATTERN gt lt ZONES gt lt TIMING ACTION gt lt MOTION DETECT gt AUTO TRACKING gt BACK EXIT PATTERN PATTERN NO 1 TITLE PATTERN 1 START lt SET gt DELETE BACK EXIT A pattern is a memorized repeating series of pan tilt Zoom and preset func tions that can be recalled with a com mand from a controller To program a pattern 1 Use the joystick to position the cursor beside PATTERN NO Press Iris Open The cursor moves to the right 2 Move the joystick up or down to view selections Press Iris Open to enter selection 3 Use the joystick to position the cursor beside SET 4 Press Iris Open The Patterns programming window appears on the monitor 5 Follow the directions displayed on the monitor To delete a pattern 1 Use the joystick to position the cursor beside DELETE 2 Press Iris Open 36 ZONES Horizon dome systems are capable of LANGUAG E ENGLISH eight zones each with a 12 character SYSTEM INFORMATION DISPLAY SETUP gt label DOM E SETTINGS lt CAMERA gt MOTION ced To program a zone IDE UE 1 Use the joystick to position the cursor p beside ZONE NO Press Iris Open and the cursor moves to the right 2 Move the joystick up or down to view selections Press lris Open to enter MOTION selection lt PRESET gt 5 T SCAN 3 Use the joystick to position the cursor SEQUENCE PATTERN beside LEFT LIMIT RIGHT2. HIGH SPEED DOME CAMERA USER S MANUAL Rancent Technologies Ltd 10 F Hong Kong Trade Centre 161 Des Voeux Road Centrl Hong Kong Tel 852 2816 7037 Fax 852 2855 8158 Table Of Contents 1 Precautions utet erede oce ni 1 2 Eeat r6Su u a 2 3 Technical nibo tbe tiet 3 4 Installation Guide oerte ette paga oa pac we ioa Ds 4 SOHINGS A tarde 8 6 Preset Setting 12 7 The OSD Menu Setting 13 1 Precautions 1 Transportation Security No heavy stress violent vibration or water splash are allowed during transportation storage The unit should be transported in separated packing In shipments of distributor and delivery of maintenance any damages caused by integral packing are not covered by warranty 2 Installation Avoid heavy stress and violent vibration during installation Don t touch the dome cover directly by hand When connecting the power source please follow all electric safety standards and only use the power supply designated for this device Keep the video and control signal in a decent distance from high voltage devices and cable Don t apply power to the dome before finishing the installation 3 Internal Environment Keep metal and inflammable material away from dome body to avoid fire short circuit and damage Please prevent all liquids material from en
3. CAMERA MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION DISPLAY SETUP gt DOM E SETTINGS lt gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT Na CAMERA SETTING AUTO FOCUS ON DIGITAL ZOOM OFF BACKLIGHT OFF FREEZE OFF ZOOM SPEED NORMAL DAY NIGHT AUTO lt ADVAN CED gt BACK EXIT AUTO FOCUS Auto focus allows the lens to remain in focus during zoom in zoom out and motion func tions There are two auto focus settings ON The camera will focus automatically when using pan tilt and zoom functions OFF Focus is operated manually BACKLIGHT ON Backlight compensation is activated OFF Backlight compensation is not activated FREEZE ON The image on the screen is freezing OFF The image on the screen is unfreezing ZOOM SPEED Zoom speed allows the user to define how fast the dome will go from full wide zoom to the max optical zoom Available zoom speed settings include the following HIGH NORMAL LOW DAY NIGHT The camera have two modes of operation color and black white The following are the settings for the IR cut filter AUTO Automatic operation is controlled by the auto IR level setting COLOR Images are always displayed in color mode BW Images are always displayed in black white mode 31 CAMERA ADVANCED MAIN MENU WHITE BALANCE LANGUAG E ENGLISH This feature automatically processe
4. POWER ON ACTION ACTION NONE BACK EXIT This setting defines a specific activity scan preset pattern to be performed in the event the power to the dome is cycled The following settings are available NONE No action PRESET Dome goes to preset 1 SCAN Dome starts auto scan operation SEQ Dome runs sequence 1 PATTERN Dome runs pattern 1 28 COMMUNICATION TEST MAIN MENU LANGUAG E ENGLISH lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt I4 DOM E SETTINGS gt lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT af Y DOME SETTINGS N lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt lt DOME TITLE gt lt CED gt lt OTHERS gt BACK EXIT ADVAN N lt SOFT ADDRESS SET gt lt VIDEO LINE LOCK gt lt AUX gt lt SOFT LIMIT gt lt POWER ON ACTION gt JI PLCOMMUNICATION TEST gt BACK EXIT a COMMUNICATION TEST N RECEIVE SEND 100 100 RELIABILITY 100 BACK EXIT reliability of the dome control Use our special software user can test the line After testing the reliability value 0 100 will display on the screen 29 MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION gt DISPLAY SETUP gt K lt DOME SETTINGS SCAMERAP lt MOTION gt RESTART FA
5. 3 06 I PEDIT 01 003 03 INS BACK EXIT SEQ NO Use the joystick to position the cursor beside SEQ NO and press the key Iris Open to enter the edition mode move the joystick up or down to select number Then press Iris Open to confirm TITLE Use the joystick to position the cursor beside TITLE and press Iris Open to enter the edition mode of sequence title START Use the joystick to position the cursor beside START and press Iris Open to start the current sequence SEQUENCE SET Use the joystick to position the cursor beside SEQUENCE SET press Iris Open to enter the sequence setting Move the cursor to EDIT and press Iris Open to enter edition mode Move the joystick right or left to select item a When the lt gt is on the item NO move joystick up or down to select the NO ofthe preset in a sequence There are up to 32 presets in a single sequence b When the gt is on the item PRESET move the joystick up or down to select the preset NO you want to add in the sequence c When the 2 is on the last item move the joystick up or down to select edition mode as insert ok and delete d Press lris Close to quit the edition 35 PATTERN MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION DISPLAY SETUP gt DOM E SETTINGS CAMERA I MOTION RESTART FACTORY DEFAULTS HELP EXIT lt gt SCAN SEQUENCE
6. CLOCK gt lt PASSWORD gt DOM E TITLE lt ADVAN CED gt lt OTHERS gt BACK EXIT IDLE ACTION TIME 30 SEC ACTION NONE BACK EXIT Idle Time This feature allows the dome to begin a specified operation scan preset or pattern after a programmed time of inac tivity Idle time can be programmed from 30 seconds to 30 minutes Idle Action The following settings are available NONE default No action PRESET Dome goes to preset 1 SCAN Dome starts auto scan operation SEQ Dome runs sequence 1 PATTERN Dome runs pattern 1 18 ALARM The dome system has 4 alarm inputs and 2 MAIN MENU alarm outputs When an alarm is received an LANGUAG E ENGLISH input signal to the dome triggers the user SYSTEM INFORMATION DISPLAY SETUP gt defined action go to preset run pattern etc LF DOM E SETTINGS lt CAMERA gt lt MOTION gt RESTART INPUT STATE FACTORY aera Used to Set the alarm contact There are two input states OPEN and CLOSE OPEN Normally open i CLOSE Normally close DOME SETTINGS ALARM MODE lt IDLE gt L p lt gt OFF Alarm function is deactivated PRIVACY MASK gt ON Alarm function is activated lt CLOCK gt lt PASSWORD gt AUTO Alarm function will be activated DOM E TITLE gt lt ADVAN CED gt between START TIME and STOP TIME lt OTHERS gt BACK ACTION EXIT Set the alarm action NONE default No action PRESET
7. LIMIT lt ZONES gt TIMING ACTION 4 Press lris Open The zone program lt MOTION DETECT gt AUTO TRACKING ming window appears on the monitor BACK 5 Follow the directions displayed on the EXIT monitor To delete a zone 1 Use the joystick to position the cursor beside DELETE ZONE IS NOT SET A 2 Press Iris Open ZONENO 1 TITLE ZONE 1 LEFT LIMIT gt RIGHT LIMIT gt DELETE BACK EXIT 37 TIMING ACTION SCHEDULE NO LANGUAG E ENGLISH Schedule Number of a day 1 8 SYSTEM INFORMATION DISPLAY SETUP gt DOM E SETTINGS CAMERA START I MOTION MN RESTART Start time of timing action FACTORY DEFAULTS EXIT STOP Stop time of timing action C MOTION MOTION Sere ina action during designated P periods of time NONE PRESET 1 8 Tal SCAN 1 4 SEQUENCE 1 4 PATTERN lt TIMING ACTION 1 4 lt MOTION DETECT gt lt AUTO TRACKING gt BACK ON OFF EXIT Enable or disable timing action function Use the joystick to position the cursor beside ON or OFF Press Iris Open to enter edition mode Move joystick up or down to select ON or OFF press Iris open TIMING ACTION z START STOP MOTION 1 00 00 00 00 wor to confirm 2 00 00 00 00 NONE 3 00 00 00 00 NONE 4 00 00 00 00 COPY 5 00 00 00 00 NONE User can copy a schedule to other 6 days 6 00 00 00 00 NONE 7 00 00 00 00 NONE i
8. Select the preset number a Use the jovstick to position the cursor beside PRESET NO Press Iris Open The cursor moves to the right b Move the jovstick up or down to view selections Press Iris Open to enter selec tion MOTION V PRESET SCAN SEQUENCE PATTERN lt ZONES gt lt TIMING ACTION gt lt MOTION DETECT gt AUTO TRACKING gt BACK EXIT PRESET PRESET NO 001 TITLE PRESETOI CALL lt SET gt DELETE BACK EXIT 2 Edit the preset label a Use the joystick to position the cursor beside TITLE b Follow the directions displayed on the monitor 3 Edit the preset scene a Use the joystick to position the cursor beside SET b Press Iris Open c Follow the directions displayed on the monitor 4 Delete the preset scene a Use the joystick to position the cursor beside DELETE b Press Iris Open 33 SCAN MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION gt DISPLAY SETUP gt DOM E SETTINGS CAMERA lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT MOTION lt PRESET gt 1e lt SCAN gt lt SEQUENCE gt lt PATTERN gt lt ZONES gt lt TIMING ACTION gt lt MOTION DETECT gt AUTO TRACKING gt BACK EXIT SCAN SCAN NO 1 TITLE SCAN 1 START LEFT LIMIT 7 RIGHT LIMIT SCAN SPEED 20 BACK EXIT SCAN NO Use the joystick to position the cursor beside SCAN NO and p
9. Video ground cee 485A 485A Control line ETT 485B Control line SGND Shell ground GND Alarm input ground AIN1 4 Alarm input P3 Alarm COM1 Alarm output 1 common NO1 Alarm output 1 normal open NC1 Alarm output 1 normal close AOD2 Alarm output 2 open drain P4 Net Net port 5 2 Dome Address Transmission Speed Protocol Setting Before the dome is installed the communication protocol baud rate and dome address should be confirmed Set the DIP switch keeping the setting consistent with the control system The relative DIP switch site and connecting wires are diagramed below for reference halal de halal SWI is address setting switch SW2 is protocol setting switch Note SW2 6 Soft address enable bit SW2 7 1200 Protocol Setting eee p Transmission Speed Setting Reeve _ Dome Address Setting PELCO P amp HS protocol SW1 8 SW1 6 SW1 7 SW1 5 SW1 3 SW1 4 SW1 2 Address SW1 1 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 254 255 10 PELCO D protocol SW1 8 SW1 6 SW1 7 SW1 5 SW1 3 SW1 4 SW1 2 Address SW1 1 10 11 12 13 14 15 16 17 1
10. ZONES 5 SEC DATE TIME ON PAN TILT 5 SEC ALARM 5 SEC G lt DISPLAY POSITION gt DISPLAY BACK EXIT DISPLAY POSITION lt DAT E TIME gt DOM E TITLE gt lt ZONES gt lt MOTION gt lt A LARM gt lt PAN TILT gt BACK EXIT Display setup allows you to program how labels are displayed on the monitor The following settings are available for each label OFF Label is not displayed when activated ON The label is continually displayed when activated i 2 SEC The label is displayed for 2 seconds after activation 5 SEC label is displayed for 5 seconds after activation 10 SEC The label is displayed for 10 seconds after activation Labels can be placed anywhere on the monitor This feature allows you to cus tomize the appearance of your monitor screen To set a label position 1 Use the joystick to position the cursor beside a label 2 Press Iris Open 3 Use the joystick to move the label up down left or right 4 Press lris Open 5 Repeat steps 1 through 4 to position other labels 6 Position the cursor next to BACK or EXIT Press lris Open to save settings and exit menu 17 IDLE ACTION MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION gt DISPLAY SETUP gt SETTINGS lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT DOME SETTINGS lt IDLE gt lt A LARM gt lt PRIVACY MASK gt lt
11. cursor HELP A EXIT beside LANGUAGE 2 Press Iris Open The cursor moves to the right beside the current selected language 3 Move the jovstick up or down to view selections Press Iris Open to enter selec tion All on screen menus are changed to the selected language 15 SYSTEM INFORMATION MAIN MENU LANGUAGE ENGLISH I SYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS CAMERA lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT EN SYSTEM INFORMATION DOME ID 1234567890 ADDRESS 001 BAUDRATE 9600 N 8 1 PROTOCOL PELCO P TEMP 31C ALARM 000000 00 IA OTHERS BACK EXIT OTHERS TITLE DOME VERSION V28200 DATE 2008 01 08 TIME 10 20 00 TEMP SCALE CELSIUS BACK EXIT The System Information screen displays dome drive model software version and other diagnostic information System settings cannot be changed using this screen This screen is for reference only Use the following steps to display the System Information screen 1 Use the joystick to position the cursor beside SYSTEM INFORMATION 2 Press Iris Open The SYSTEM INFOR MATION screen opens 16 DISPLAY SETUP MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION gt DISPLAY SETUP DOM E SETTINGS gt lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT DOME TITLE OFF PRESET 5 SEC MOTION 5 SEC
12. 5 2 3 Built in High Definition Day Night Camera e Auto iris auto back light compensation e Auto manual white balance e Auto manual focus e Auto manual brightness control e Multiple kinds of camera for options 2 4 All weather Outdoor Design e Built in heater e Built in fan can operate in 60 C e High Die cast Aluminum Construction e IP66 water proof e 3000V lightning and surge current proof 2 3 Technical Data PowerPower Supply Operating Temperature Operating moisture Power Consumption Communication Communication transmission speed Protocols Pan speed Titlt speed Pan Tilt Accuracy Preset Speed Pan Angle Tilt Angle Preset Positions Auto Scan Cruise Track Cruise Points Qty per cruise group Pattern Tours Alarm Privacy Zone 35 C 60 C 95 55W RS 485 bus 2400 4800 9600BPS Pelco D Pelco P HS 0 01 180 s 0 04 120 5 0 05 600 s 360 Continuously 220 8 Groups 8 Groups 32 Preset Positions 4 Groups 4 alarm inputs and 2 outputs 8 zones IP66 water proof 3000V lightning proof 4 Installation Guide 4 1 Installation Preparation Video Coaxial Cables Mode Max Distance RG59 U 750ft 229m RG6 U 1 000ft 305m RG11 U 1 500ft 457m 4 2 Structure Bracket Dome base Dome body Dome cover 4 3 Installation Size P usc 87 V Dome wa T Dome cover 4 4 In
13. 8 19 20 21 22 23 24 25 26 27 28 29 30 31 32 253 254 11 6 Preset Setting Speed dome camera supports 220 preset positions The code numbers 1 64 and 100 255 represent the 220 preset positions You can activate some special functions by calling upon code number 65 99 NO Command Command packet Comments 1 Start Auto Scan Call 99 Default to start the first group of auto scan 2 Start Sequence Call 98 Default to start the first group of sequence 3 Start Pattern Call 97 Default to start the Tours first group of Pattern Tours 4 Start the scan Call 80 call pp PP means group of group call 99 No 1 8 5 Start sequence Call 80 call pp PP means group of group N call 98 No 1 8 6 Start pattern Call 80 call pp PP means group tour of group N call 97 No 1 4 7 Stop Auto mode Call 96 End setting Open the menu Call 95 9 Remote reset Call 94 10 Restore factory 82 default setting 12 7 The OSD Menu Setting Operation Method of the Menu 1 Access main menu call preset 95 2 Use the joystick to position the cursor beside menu selec tion NOTE If your controller does not have a joystick use the up or down key 3 Press lris Open the submenu cursor moves to the right 4 Move the joystick up or down to view selections 5 Press Iris Open to make selection 6
14. CTORY DEFAULTS HELP EXIT DOME SETTINGS lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt lt DOME TITLE gt lt ADVAN CED gt 7 OTHERS BACK EXIT OTHERS TEMP MODE AUTO INTERNAL FAN AUTO PRESET FREEZE OFF AUTO FLIP STOP TIME 30 SEC MENU OFF TIME 5 MIN NORTH SETP BACK EXIT DOME OTHER SETTINGS TEMP MODE Temperature control mode COOL Fan pwoer on heater auto AUTO Fan auto heater auto HEAT Fan power on heater power on OFF Fan power off heater power off INTERNAL FAN Control internal fan speed PRESET FREEZE This feature freezes the scene on the monitor when going to a preset This allows for smooth transition from one preset scene to another AUTO FLIP When the camera tilts downward and goes just beyond the vertical position the dome rotates 180 degrees When the dome rotates flips the camera starts moving upward as long as you continue to hold the joystick in the down position Once you let go of the joystick after the dome rotates joystick control returns to normal operation STOP TIME This is the amount of time the dome stops after receiving the last command NORTH SET North is the pan angle from zero to 359 degrees zero is the pan position you specify to be the zero degree point zero is normally set to magnetic north Once set north and compass readings are based on the set North Zero point 30
15. Dome goes to preset SCAN Dome starts auto scan operation ALARM SETTING SEQ Dome runs sequence PATTERN Dome runs pattern INPUT STATE OPEN uns pater ALARM MODE OFF ACTION NONE ALARM OUT OFF ALARM OUT RESET TIME 10 SEC tth xiliary t tivate STARTTIME 00 00 Set the auxiliary to activate STOP TIME 00 00 OFF Not activated BACK OUT1 An alarm action will close AUX 1 EXIT OUT2 An alarm action will activate AUX 2 open drain output ALL Both AIX 1 and AUX 2 are activated RESET TIME This is the amount of time the dome deactivates the alarm ouputs 19 PRIVACY MASK LANGUAG E ENGLISH SYSTEM INFORMATION gt DISPLAY SETUP gt DOME SETTINGS gt lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT MAIN MENU N Privacv mask allows a user to program areas that cannot be viewed the operator of the dome svstem A blanked area will move with pan and tilt functions and automaticallv adjust in size as the lens zooms telephoto and wide MASK NO Move the cursor to MASK NO to set the Y NO of privacy mask zone DOME SETTINGS lt IDLE gt lt ALARM gt I RPRIVACV MASK gt lt CLOCK gt lt PASSWORD gt lt DOME TITLE gt lt ADVAN CED gt lt OTHERS gt BACK EXIT PRIVACY MASK MASKNO 1 ENABLE OFF SET DELETE BACK EXIT ENABLE Move the cursor to to enable or disable the privacy mask zone SET M
16. F PHASE ADJUST 000 EXIT 25 N MAIN MENU LANGUAG E ENGLISH lt SYSTEM INFORMATION gt DISPLAY SETUP gt DOME SETTINGS gt lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT DOME SETTINGS lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt DOM E TITLE gt ADVAN CED gt OTHERS BACK EXIT ADVAN lt SOFT ADDRESS SET lt VIDEO LINE LOCK gt AUX gt lt SOFT LIMIT gt lt POWER ON ACTION gt lt COMMUNICATION TEST gt BACK EXIT i AUX AUXI OFF AUX2 OFF BACK EXIT An auxiliary output is a programmable signal from the dome back box that can trigger another device to operate An auxiliary output is programmable to trigger from an alarm or from a controller An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the relay The output of AUX 1 can be connected to the alarm input of a system switch to activate automatic monitor switching and recording An AUX 2 command from the controller will place a ground at the output of AUX 2 to oper ate the device that is connected to it 26 SOFT LIMIT MAIN MENU DISPLAY SETUP gt 2 lt SETTINGS lt gt lt MOTION gt RESTART LANGUAG E ENGLISH lt SYSTEM INFORMATION gt FACTORY DE
17. FAULTS HELP EXIT DOME SETTINGS lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt lt DOME TITLE gt I PSADVAN CED gt lt OTHERS gt BACK EXIT Y ADVAN CED lt AUX gt J PSSOFT LIMIT gt BACK EXIT lt SOFT ADDRESS SET gt lt VIDEO LINE LOCK gt lt POWER ON ACTION gt lt COMMUNICATION TEST gt LIMIT SETTING SOFT LIMIT OFF LEFT LIMIT gt RIGHT LIMIT gt LIMIT DELETE BACK EXIT Limit stops are programmable stops that limit the pan range of the dome There must be two limits a left and a right to define an area To set manual or scan stops 1 Use the joystick to position the cursor beside LEFT LIMIT or RIGHT LIMIT 2 Press lris Open 3 Follow the directions displayed on the moni tor 27 POWER ON ACTION C MAIN MENU N LANGUAG E ENGLISH SYSTEM INFORMATION DISPLAY SETUP J PEDOME SETTINGS lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT 2 DOME SETTINGS lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt lt DOME TITLE gt 22 lt CED gt lt OTHERS gt BACK EXIT ADVAN CED N lt SOFT ADDRESS SET gt lt VIDEO LINE LOCK gt lt AUX gt lt SOFT LIMIT gt l lt POW ER ON ACTION gt lt COMMUNICATION TEST gt BACK EXIT
18. PLAY SETUP gt E SETTINGS gt CAMERA lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT M A DOME SETTINGS A lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWOR D gt lt DOME TITLE gt K6SSADVAN CED gt lt OTHERS gt BACK EXIT C ADVAN CED N ADDRESS SET gt lt VIDEO LINE LOCK gt lt AUX gt lt SOFT LIMIT gt lt POWER ON ACTION gt lt COMMUNICATION TEST gt BACK EXIT C DOME SOFT ADD RESS SET N SOFT ADDRESS 001 INPUTID 123456789 0 INPUT 012345678 9 SOFT ADDRESS OFF GOK CANCEL P DOME SOFT ADDRESS SET N SOFT ADDRESS 001 INPUT 000 255 INPUT 012345678 9 SOFT ADDRESS OFF OK CANCEL Dome support soft address function use this function bit 7 of setting switch 2 must be set to on In this case address setting switch 1 will be ignored 1 Before setting soft address dome id should be inputed Use the jovstick to position the cursor beside O 1 2 3 4 5 6 7 8 9 press Iris Open move jovstick left or right to select number press Iris Open the number selected will be inputed on the upper line 2 Enable or disable soft address function Use the joystick to position the cursor beside SOFT ADDRESS ON OFF press Iris Open to enter edition mode move joystick up or down to select ON or OFF press Iris Open to confirm 3 Use the joystick
19. Press lris Close to cancel selection 13 OSD Menu Tree SYSTEM INFORMATION uem ENT DOME ID 123456789 0 ADDRESS 001 BAUDRATE 9600 N 8 1 PROTOCOL PELCO P TEMP 31C ALARM 000000 00 OTHERS BACK EXIT gt DISPLAY DOME TITLE OFF PRESET 5 SEC MOTION 5 SEC ZONES 5 SEC DATETIME ON PAN TILT 5 SEC ALARM 5 SEC DISPLAY POSITION BACK EXIT MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION DISPLAY SETUP gt lt DOME SETTINGS gt lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT DOME SETTINGS lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt lt DOME TITLE gt lt ADVAN CED gt lt OTHERS gt BACK EXIT CAMERA SETTING AUTO FOCUS ON DIGITAL ZOOM OFF BACKLIGHT OFF FREEZE OFF ZOOM SPEED NORMAL DAY NIGHT AUTO lt ADVAN CED gt BACK EXIT MOTION lt PRESET gt lt SCAN gt lt SEQUENCE gt lt PATTERN gt lt ZONES gt lt TIMING ACTION gt lt MOTION DETECT gt lt AUTO TRACKING gt BACK EXIT LANGUAGE The language for the on screen menus is LANGUAG E ENGLISH selectable Available languages include SYSTEM INFORMATION DISPLAY SETUP gt English and Chinese lt DOME SETTINGS gt lt CAMERA gt lt M OTION gt z RESTART To change the display language FACTORY DEFAULTS 1 Use the joystick to position the
20. ction of motion target on the screen 40 RESTART RESTART SYSTEM Reboot the system if it is not operating or LANGUAG E ENGLISH l l SYSTEM INFORMATION if there is no control Rebooting the DISPLAY SETUP gt A DOM E SETTINGS system will cycle dome and camera CAMERA lt MOTION gt power without changing programmed IPRESTART 4 FACTORV DEFAULTS dome settings HELP EXIT WARNING ARE YOU SURE OK CANCEL 41 FACTORY DEFAULTS C MAIN MENU Restore factory default settings of the LANGUAG ENGLISH dome SYSTEM INFORMATION DISPLAY SETUP gt DOME SETTINGS CAMERA lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT WARNING ARE YOU SURE OK CANCEL 42 HELP id Disply menu operating help information LANGUAG E ENGLISH SYSTEM INFORMATION gt on the screen DISPLAY SETUP gt lt DOME SETTINGS gt lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP G EXIT Y MENU OPERATION HELP N I CALL PRESET95 TO OPEN MENU 2 MOVE JOYSTICK TO SELECT MENU ITEM 3 IRIS OPEN TO ENTER EDIT MODE 4 MOVE JOYSTICK TO EDIT PARAMETERS 5 IRIS OPEN TO CONFIRM BACK EXIT 43
21. n a week 8 00 00 00 00 ONE OFF COPY BACK BACK Go back to upper menu 38 MOTION DETECT i MAIN MENU LANGUAG E ENGLISH lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt DOM E SETTINGS gt lt CAMERA gt SCENE NO Select motion detection scene number 1 8 EDIT SCENE Set motion detection scene lt MOTION gt FACTORY DEFAULTS EDIT AREA HELP Edit detection areas four motion detection areas U can be defined i PREVIEW SCENE a VOTON Preview motion detection scene and areas lt PRESET gt DELETE SCENE Wie elie Delete motion detection scene ZTIMING ACTION AUX ACTIVATE Motion detection can be programmed to trigger p auxiliary command when motion is detected The following are the settings for AUX ACTIVATE OFF AUX1 AUX 2 MOTION DETECT CANCEL TIME SOENE NO 2d Cancel time is the length of time the auxiliary will remain on after motion is detected DELETE SCENE gt AREA NO CANCES mi Select motion detection area number 1 4 lt START gt AREA EDIT ERIE Edit motion detection area on the screen a J DELETE 1 Delete motion detection area AREA EDIT SENSITIVITY ARRANO 2 3 Set the sensitivity of the motion detection area The A following are the settings for SENSITIVITY LOW SENSITIVITY MID MID HIGH AREA DISPLAY OFF AREA DISPLAY The following are the settings ON Display the area o
22. n screen after motion is WK J detected OFF Do not Displav the area after motion is detected 39 AUTO TRACKING a MAIN MENU E LANGUAG E ENGLISH SYSTEM INFORMATION gt DISPLAY SETUP gt DOM E SETTINGS lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT Ne i MOTION N lt PRESET gt lt SCAN gt lt SEQUENCE gt lt PATTERN gt lt ZONES gt lt TIMING ACTION gt lt MOTION DETECT gt F AUTO TRACKING gt BACK EXIT k i AUTO TRACKING N SENSITIVITV MID TARGET MID ZOOM MATCH X22 ENABLE OFF TRACKING SCENE SET BACK EXIT c P TRACKING SCENE SET TRACKING SCENE SET gt DELETE RETURN DELAY 105 BACK EXIT SENSITIVITY Set the sensitivity of tracking HIGH The sensitivity level is high MID Average sensitivity LOW The sensitivity level is low TARGET Set the tracking target size LARGE The tracking target size is large MID Average target size SMALL The tracking target size is small ZOOM MATCH _ Zoom match allows the user to define a limitation on the amount of telephoto zoom durning target track ing ENABLE ON Activate auto tracking function OFF Deavtivate auto tracking function TRACKING SCENE SET Set the preset scene that the auto tracking function start from RETURN TIME Set the length of the time the dome return to auto tracking preset scene after the last dete
23. ove the cursor to SET and press Iris Open to enter the edition mode of privacy mask zone Then the sentence PRESS IRIS OPEN TO CONFIRM will be displayed on the monitor Use joystick to move the dome to the area you want to cover and press IRIS OPEN to confirm There will be a privacy zone in the middle of the monitor Move joystick up down left and right to adjust the size of privacy zone DELETE Move the cursor to DELETE and press IRIS OPEN to delete the current privacy zone 20 CLOCK The clock is used to program the current LANGUAG E ENGLISH date and time The date and time set in SYSTEM INFORMATION DISPLAY SETUP gt the Clock menu is used to program LEDOM E SETTINGS gt CAMERA events The date and time can also be lt MOTION gt i RESTART displayed on the monitor when the FACTORY DEFAULTS menus are not being accessed HELP EXIT DOME SETTINGS lt IDLE gt ALARM PRIVACY MASK gt I ECLOCKP PASSWORD DOM E TITLE lt ADVAN CED gt lt OTHERS gt BACK EXIT DATE TIME DATE 2009 01 01 TIME 12 00 CANCEL 22 PASSWORD The dome features password protection LANGUAG ENGLISH SYSTEM INFORMATION DISPLAY SETUP gt SETTINGS gt lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS HELP EXIT to prevent unauthorized changes to the dome settings An operator cannot access any of the dome
24. ress lris Open to enter the edition mode of scan No move the joystick up or down to select number Then press IRIS Open to confirm TITLE Use the joystick to position the cursor beside TITLE and press lris Open to enter the edition mode of scan title START Use the joystick to position the cursor beside START and press lris Open to start the current scan LEFT LIMIT Use the joystick to position the cursor beside LEFT LIMIT and press lris Open to start setting the left limit of the current scan RIGHT LIMIT Use the joystick to position the cursor beside RIGHT LIMIT and press lris Open to start setting the right limit of the current scan SCAN SPEED Use the joystick to position the cursor beside SCAN SPEED and press lris Open to enter the edition mode of scan speed Move the joystick up or down to select a speed scale then press lris Open to confirm The speed scale ranges from 1 30 34 SEQUENCE MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION DISPLAY SETUP DOME SETTINGS CAMERA A MOTION RESTART FACTORY DEFAULTS HELP EXIT MOTION N lt PRESET gt lt SCAN gt FP lt SEQUENCE gt lt PATTERN gt lt ZONES gt lt TIMING ACTION gt lt MOTION DETECT gt lt AUTO TRACKING gt BACK EXIT A SEQUENCE SEQ NO 1 TITLE SEQ 1 START SEQUENCE SET DELETE BACK EXIT SEQUENCE NO I PRESET NTERVAL gt gt 01 002 03 02 0010
25. s the SYSTEM INFORMATION gt lt DISPLAY SETUP gt lt DO ME SETTINGS gt KS lt CAMERA gt lt MOTION gt RESTART FACTOR Y DEFAULTS HELP EXIT CAMERA SETTING AUTO FOCUS ON DIGITAL ZOOM OFF BACKLIGHT OFF FREEZE OFF ZOOM SPEED NORMAL DAY NIGHT AUTO ADVAN CED gt BACK EXIT Xe ADVAN CED WB RED GAIN 208 BLUE GAIN 167 BRIGHT 01 EXPOSURE WIDE DYNA MIC OFF BACK EXIT viewed image to retain color balance over a color temperature range The default setting for auto white balance is ON RED GAIN Adjusts the picture output in the red range As you change the value you will see the color change on your monitor BLUE GAIN Adjusts the picture output in the blue range As you change the value you will see the color change on your monitor BRIGHT Set the brightness of image display on the monitor EXPLOSURE Set the explosure mode of the camera WIDE DYNAMIC Wide dynamic range WDR balances the brightest and darkest sections of a scene to produce a picture that is better balanced in lighting and provides more detail Available settings are OFF and ON The default setting is OFF 32 PRESET MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION gt DISPLAY SETUP DOM E SETTINGS gt CAMERA IPSMOTION RESTART DEFAULTS HELP EXIT Use the following steps to program a preset 1
26. settings menus without a valid password EDIT PASSWORD At least one character must be entered Y to create a valid password DOME SETTINGS lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt 1 lt PASSWORD gt lt DOME TITLE gt lt ADVAN CED gt lt OTHERS gt BACK EXIT ENABLE ON Enable password protection OFF Disable password protection C PASSWORD TR EDIT PASSWORD ENABLE OFF BACK EXIT 22 DOME TITLE MAIN MENU Dome title is the label used to identify the LANGUAG E ENGLISH camera viewed on the monitor Up to 12 SYSTEM INFORMATION DISPLAY SETUP gt characters can be used for a title SETTINGS 3 lt CAMERA gt To edit the title text label do the following lt MOTION gt RESTART Mad dE 1 Use the joystick to position the cursor EXIT beside DOME TITLE Y 2 Press Iris Open The text input window appears on the monitor DOME SETTINGS lt IDLE gt lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt lt DOME TITLE gt lt ADVAN CED gt lt OTHERS gt 3 Enter text 4 Use the joystick to position the cursor beside OK press Iris Open the text inputed will be saved BACK EXIT DOME TITLE SE T IMPUT lt CAPS gt ABCDEFGHIJ KLMNOPQRST UVWXYZ c OK CANCE L 23 SOFT ADDRESS MAIN MENU LANGUAG E ENGLISH SYSTEM INFORMATION DIS
27. stallation Procedures Notice The wall must be thick enough to install the expansion screws and can bear 4 times the weight of the dome camera itself 1 Bore 4 holes by using templates included on the wall 3 Put the cables through the bracket Fix the dome base and the bracket with M5 screws 4 Use screw caps and shims to fix the bracket on the wall 5 Set the dome address system baud rate and protocol by configur ing DIP switches SW1 and SW2 located on the bottom of dome body The Plug in on the dome body must be seated rightly with the socket on the dome base 6 Attach the dome cover to the dome base with rope 7 To lock the dome body to the dome base line up the A and B tabs on the dome body with the A and B label on the dome base Push in on the tabs Insert one side and then the other side Continue pushing one the ends of the tabs until both sides click into place Make sure the plug in on the dome body is fully locked by the socket on the dome base Then press the dome body lightly and check if the dome body is fully locked to avoid shedding and abrasion with the dome cover o Settings 5 1 Interface e z gt z e s gt gt e gt z s gt 485A A85B SGND VIDEO VGND AC24V SGND 24 Port Comments P1 Power AC24V AC24V Input SGND Shell ground VIDEO Video signal P2 VGND
28. tering the dome If occur this please shut down the power and pull out the plug Then inform the technical personnel immediately 4 Electrical Safety The video image would be interfered when the dome is installed near television radio transmitter voltage changer and audio amplifier 5 Camera Protection Avoid shooting very bright objects directly into the camera s CCD such as the sun or light fittings 6 Cleaning Method Please don t use abrasive and violent detergent to clean the dome Please choose dry fabric and neutral detergent Use lens paper to clean the lens 2 Features 2 1 Built in Decoder e 220 programmable presets e 8 cruising tracks each cruising track has 32 preset positions e 4 pattern tours each one with 600s memory e RS 485 bus e 8 groups of auto scan the left and right boundary and scan speed can be set e Pelco P and Pelco D HS compatible e 4 alarm inputs and 2 outputs e Guard location the dome can operate preset auto scan cruising and pattern tours functions after a short pause e Alarm triggering the alarm can trigger preset auto scan cruising and pattern tours functions 2 2 Integrated Universal Speed Change Rotator e Delicate stepping motor stable sensitive and accurate e 360 continuous pan without blind area e Stepless speed change auto zoom speed matching e Auto overturn function e Manual speed Pan 0 01 180 S Tilt 0 01 120 S e Presets calling speed 600
29. to position the cursor beside OK press Iris Open to confirm the dome ID has been inputed 4 Use the joystick to position the cursor beside 0 1 2 3 4 5 6 7 8 S9 press Iris Open move joystick left or right to select number press Iris Open the number selected will be inputed on the upper line 5 Use the joystick to position the cursor beside OK press Iris Open to confirm Then follow the direction display on the screen 24 VIDEO LINE LOCK MAIN MENU Line sync refers to a programmable function that allows you to synchronize all cameras DISPLAY SETUP gt B 1 DOM E SETTINGS gt within a matrix system lt CAMERA gt lt MOTION gt RESTART FACTORY DEFAULTS VIDEO LINE LOCK HELP l EXIT ON Adjusts the phase of the line sync to ES A svnchronize input power OFF The dome svnchronizes to the internal DOME SETTINGS pens clock lt ALARM gt lt PRIVACY MASK gt lt CLOCK gt lt PASSWORD gt PHASE TURNOVER lt DOME TITLE gt I lt ADVAN CED gt ON Line sync phase turn over 180 degrees lt OTHERS gt ace OFF Line sync phase is not turn over EXIT M 7 PHASE ADJUST Adjust line sync phase from 0 to 180 degrees ADVAN CED lt SOFT ADDRESS SET gt lt VIDEO LINE LOCK gt lt AUX gt lt SOFT LIMIT gt lt POWER ON ACTION gt lt COMMUNICATION TEST gt BACK EXIT ss sZ ali VIDEO LINE LOCK N VIDEO LINE LOCK OFF PHASE TURNOVER OF
Download Pdf Manuals
Related Search