DMC-1000 Chassis-Based Media Converter User`s Guide - D-Link
Contents
1. T lt gt 1000BASE SX LX 1000BASE SX lt gt 1000BASE LX multi mode lt single mode In this manual you will find Introduction on the Chassis System Product features Illustrative LEDs functions Installation instructions Specifications Ordering Information Attention assis shown in the figures of this manual is fitted with lant power supplies Proprietary media converters and a second power supply shall be ordered separately 19 Media Converter Chassis System The chassis equipped with two power supplies and sixteen media converters Attention chassis system ships with only one power supply Drietary media converters and a second power supply are not ded PRODUCT FEATURES This chapter describes the features of the Media Converter Chassis System Product Features Plug and Play House up to Sixteen media converters Front panel LEDs for bay and fan power status Standard 19 rackmountable size 2U Non stop operation amp minimal downtime VV V V V V The following items are designed to be hot swappable to allow easy and quick replacement Media converters Redundant Power supplies gt Provides cooling fans at the back together with power supply gt Power redundancy amp power isolation gt high quality internal power supply provided and a second power supply option for load sharing purpose Load sharing mechanism If one power supply should fail the redundant power2. status feedback and helps monitor and troubleshoot when needed Front Panel There is an array of LED indicators which provides you with instant feedback on the status of the power and the fan DMC 1000 D Link Power and Fan LED 1 2 Indicates which the power fan is working depends on where the power supply was installed at the rear Power LED On Green Power supply feed in Off No power supply feeding Power Fail On Amber Faulty power supply LED Off Power supply works normally Fan Fail LED Amber Faulty Fan Off Fan works normally 12 TECHNICAL SPECIFICATIONS Chassis System Sixteen bays for housing up to sixteen Capacity media converters One power supply provided hot swappable A second power supply for load sharing is optional also hot swappable Coolin Two fans mounted together with the 8 power supply or alone at the rear 2 LEDs for fan status 2 LEDs for power feeding status Indicators 2 LEDs for power supply s power status W415 mm x D 390mm x H89 mm Dimensions Standard 19 size 2U 7 0kg approx Net Weight EL Only one power supply included Emissions FCC Class A CE Mark Class A VCCI Class A 13 Rated Voltage Speed 3200 RPM 250 RPM Air Delivery 42 5 CFM per min Noise Level 36 5dB A Bearing Precise ball bearing system System Dimensions 80 x 80 x 25 mm 12Vdc Powe
3. supply is capable of taking over immediately gt Media Converter s power isolation ensures each bay is electrically isolated from each other UNPACKING AND INSTALLATION This chapter provides unpacking and installation information for the Switch To avoid causing any damage to the Switch we recommend that you read this chapter carefully before starting installation Unpacking When unpacking the product package you shall find these items listed below gt 19 Media Converter Chassis System One power supply installed on the chassis One AC power cord User s Manual v v v V Accessories rackmount screws 8 pcs amp rackmount ears 2 pcs rubber foot 4 pcs If any item is found missing or damaged please contact your local reseller for replacement Installation The site where you place the chassis system may greatly affect its performance When installing take the following into your consideration As with any electric device you should place the equipment where it will not be subjected to extreme temperatures humidity or electromagnetic interference Specifically the site you select should meet the following requirements The ambient temperature should be between 32 and 104 6 degrees Fahrenheit 0 to 40 degrees Celsius The relative humidity should be less than 90 percent non condensing Surrounding electrical devices should not exceed the electromagnetic field RFC standards for IEC 801
4. 3 Level 2 3V M field strength Make sure that the equipment receives adequate ventilation at the rear Do not block the fan exhaust holes on the rear of the chassis The power outlet should be within 1 8 meters of the chassis Deciding How to Install the System We strongly suggest that you install the chassis first as this is more convenient for you to install media converters into the chassis with ease The accessories supplied in the product package includes rackmount screws 8 pcs and rackmount brackets 2 pcs This well built chassis can be installed in the following ways Mounted to 19 inch standard rack Use the rackmount brackets and screws to install the chassis into any 19 standard rack 1 Attach the brackets to each side of the chassis Apply four screws to each side and secure them tightly Step 2 Carefully position the chassis into the rack Align the brackets to the side holes on the rack and use rack screws to secure the chassis with the rack Step 3 Proceed to the Connecting to Power section Installing Media Converter The chassis is equipped with sixteen media converter carriers each of which is fitted into bays of the chassis Step 1 To install a media converter module onto the chassis you have to unscrew the bay cover from the desired bay first Step 2 Unscrew the hand screw counter clockwise by using hand or screwdriver and pull out the media converter o
5. D Link DMC 1000 Chassis Based Media Converter User s Guide Rev 01 Jan 2002 6012 9600131 1907MCR11616000 Printed In Taiwan RECYCLABLE i TABLE OF CONTENTS TABLE OF CONTENTS II PREFACE OT 3 19 MEDIA CONVERTER CHASSIS SYSTEM 4 PRODUCT FEATURES 5 PRODUCT FEATURES ote a Qua nh 5 UNPACKING AND INSTALLATION 6 UNPACKINGa m 6 INSTALLATION cot sS aa pede din EEUU d aeta debes eife tet 6 DECIDING HOW TO INSTALL THE SYSTEM 7 Mounted to 19 inch standard 8 Installing Media Converter eee 9 Connecting to Power Power Supply see 10 Installing and Removing the Power Supply sss 11 UNDERSTANDING LED INDICA TORS 12 a SR Dose natu Mea OS 12 POWER AND FAN LED S dese ne elm a 12 TECHNICAL SPECIFICATIONS 13 PREFACE This manual describes how to install and use the 19 Media Converter Chassis System The system introduced here is capable of housing up to sixteen media converters each of which offers one channel media conversion solution 100BASE TX lt lt IO0BASE FX 10 100BASE TX 100BASE FX 100BASE FX lt gt 100BASE FX multi mode e single mode 1000BASE
6. r Supply AC inputs 100 to 240 VAC universal power supply Power Consumption 150 watts max Temperature Operating 0 40 C Storage 10 50 C Humidity Operating 10 90 Storage 5 90 Overload All outputs protected from short circuit Protection condition automatic recovery 14
7. tion mechanism so that it is free from any problem that might occur to the power supplies or faulty converter bay This is the best solution to protect your investment in media converters There is an optional solution for the backup power lt DC to DC Power Supply The chassis system is equipped with one power supply and allows one additional power supply for redundancy For reliable operation we suggest that you run the chassis system with two power supplies are in place 10 Step 1 Connect the supplied AC power cord to the back of the chassis Step 2 Attach the plug into a standard AC outlet with a voltage range from 100 240Vac Step 3 Turn on the chassis system by flipping the switch beside the receptacle to ON position The LED on the front panel of power supply will come on then Installing and Removing the Power Supply To remove a power supply out the chassis you have to loose the hand screw counter clockwise and pull out the power supply from the chassis e To install a power supply to the chassis you have to fasten the hand screw clockwise and slide in the power supply to the chassis You can slide in and out the power supply from the bay fasten orloose the hand screw clockwise orcounter clockwise by using hand or screwdriver Attention the Chassis System needs to work alone you can k up four Rubber foot below the chassis 11 UNDERSTANDING LED INDICATORS The front panel LEDs provide instant
8. ut the carrier as shown below pe Te h LS Unscrew the hand screw counter clockwise mum by using hand or screwdriver and pull the media converter module out on the carrier o B Step 3 Carefully slide in the module and fasten the hand screw clockwise by using hand or screwdriver until it is fully and firmly fitted into the slot of the chassis Insert the media converter module into an available slot and fasten the hand screw clockwise by using hand or screwdriver Connecting to Power Power Supply The chassis ships with only one power supply and a second power supply option is at your discretion When the chassis is equipped with two power supplies you can have the following advanced performance Hot Swappable The design of the power system is based on an idea of providing maximum flexibility and redundancy In this way you may remove any of the two power supplies without turning off the system Redundancy During operation both power supplies are switched on and share the current load In case that one of them should fail the other will instantaneously take 10096 of the load without any loss Similarly if one power supply is removed from servicing it can be switched off and removed while the chassis continues functioning Protection System The power of each converter bay comes from the two shared power supplies Each bay is isolated from each other under a certain protec
Download Pdf Manuals
Related Search