DPAMicrophones 4017 manual
Contents
1. Matt black Material Aluminum Dimensions Microphone length 210 mm 83 in Microphone diameter 19 mm 075 in Weight 71 g 25 oz ACCESSORIES INCLUDED Holders UA0639 Microphone Clip Acoustic Equalizers and Windscreens DUA0073 Windscreen for 4017 ACCESSORIES AVAILABLE Holders UA0897 Shock Mount TB4000 Table Base Windshield Systems WINDPAGL Microphone Windshield System Large Please refer to www dpamicrophones com for more information CARE OF MICROPHONE No preventive maintenance is required on this product The microphone car tridge is tightly secured to the main body housing and no attempt should be made to remove it Use of windscreen is recommended when microphones are used in dirty dusty and windy environments When not in use the microphone should be disconnected and kept in the case supplied or similar protection SERVICE REPAIR Products from DPA Microphones are extremely stable and there should not be any significant change in the specifications with time and use If however you are not totally satisfied with the characteristics exhibited by your product contact your nearest DPA Microphones representative for further details of service and the repair facilities that are available WARRANTY All products from DPA Microphones are covered by a two year limited warranty on both mechanical functionality and documented specifications as long as the items are not mistreated abused or2. Furthermore it can be used to tune the desired amount of bass in a voice as the bass response of the microphone is influenced by the proximity effect Short distances to a performer will usually require the bass roll off filter to be switched on to compensate for the low fre quency rise FULL SPECIFICATIONS Cartridge type 19 mm 075 in pre polarized condenser Principle of operation Pressure gradient supercardioid with interference tube Power supply 48 V Phantom power Frequency range 2 dB 70 Hz 20 kHz permanent third order high pass filter at 50 Hz Switching filters High boost 4 dB at 8 kHz shelving Bass roll off first order filter below 300 Hz Directional characteristics Supercardioid lobe shaped shotgun Sensitivity nominal 2 dB 30 mV Pa 30 dB re 1 V Pa Equivalent noise level A weighted Typ 14 dB A max 15 dB A Equivalent noise level ITU R BS 468 4 Typ 25 dB max 26 dB Max SPL peak before clipping B2 dB Total harmonic distortion lt 05 up to B0 dB SPL peak lt 1 up to BI dB SPL peak Output voltage Max 2 2 V peak Output impedance lt 200 ohm Dynamic range Typ 117 dB S N ratio re 1 kHz at 1 Pa 94 dB SPL 80 dB A Connector XLR 3M Pin 1 Ground Pin 2 Signal phase Pin 3 Slgnal phase Polarity Positively increasing sound pressure creates positive going voltage on pin 2 Current consumption 45 mA Cable drive capability Up to 100 m 328 ft Color
3. modified in any way Invoices are required as warranty registration documents in case of a claim Find your nearest DPA representative on our website www dpamicrophones com or send e mail to info dpamicrophones com DPA Headquarters Denmark Tel 45 4814 2828 Fax 45 4814 2700 DPA Inc United States Tel 1 303 485 1025 Fax 1 303 485 6470 CE MARKING The CE mark guarantees that all products conform with relevant standards approved by the European Community The products described in this Users Manual comply with current relevant standards when used with cables from DPA Microphones EMC Directive 89 336 EEC amended by 92 31 EEC and 93 68 EEC Low Voltage Directive 73 23 EEC amended by 93 68 EEC a ENVIRONMENTAL POLICY DPA Microphones A S is proud to be known as a green company It is company policy to produce all products in accordance with the best ecological practices to pre serve the environment we are all a part of Consequently it is DPA s aim to cooperate with both national and international legislative bodies to fulfil the requirements and recommendations set out in environmental standards and directives Throughout DPA s conduct and in its design of new products the company pursues solutions that have minimal impact on the ecology and are in line with the latest legislative requirements at present directive 9002 95 EC at the time a new product is introduced to the market These requirements are not
4. pin 2 and pin 3 Signal Signal Ground Fig 1 External view of the output connector of the DPA 4017 Fig 2 Directional characteristics of DPA 4017 normalized Without filter High boost 4 dB at 8 kHz dB 10 Bass roll off 300 Hz 6 dB oct 01 20 Hz 50 100 200 500 1kHz 2 5 10 20 40 Fig 3 Frequency response of switching filters 10 o o 30 dB 10 160 90 20 30 20 Hz 50 100 200 500 1kHz 2 5 10 20 40 Fig 4 On and off axis responses of DPA 4017 measured at 60 cm 236 in Filters DPA 4017 features two switching filters which are controlled at the switching ring and a permanent third order high pass filter at 50 Hz See fig 3 Switching filters High boost When the switching ring is turned on the filter is on giving 4 dB at 8 kHz shelving lt is recommended for any high frequency loss caused by use of third party manufacturers windshield Use DPA WINDPAC to avoid any high frequency attenuation Bass roll off By turning the switching ring on the filter is on giving a first order 6 dB oct bass roll off below 300 Hz This decreases unwanted low frequency disturbance from handling and wind noise
5. USER S MANUAL Shotgun Microphone DPA 4017 DPA ae USER S MANUAL Shotgun Microphone DPA 4017 CONTENTS Introduction Technical description Full specifications Accessories included Accessories available Care of microphone Service repair Warranty CE marking Environmental policy interstage Phistersvej 31 2900 Hellerup Danmark Telefon 3946 0000 fax 3946 0040 www interstage dk pro audio with a smile INTRODUCTION The DPA 4017 is a short and exceptionally lightweight shotgun microphone offering a very directional pickup pattern with the typical natural DPA clarity maintained The 4017 has been designed for a broad range of uses from camera systems to fixed positions at sports facilities and for booming in ENG broadcast and film applications Due to its remarkable clarity wide dynamic range and excellent rejection characteristics the 4017 is equally at home in the recording studio and when used for sound reinforcement live music miking At just 210 mm 83 inches in length and 71 grams 2 5 ounces in weight the 4017 is compact in size and among the lightest boom microphones available TECHNICAL DESCRIPTION The cartridge The condenser capsule uses a high voltage pre polarized back plate giving the DPA 4017 high output sensitivity 30 mV Pa as well as low noise and low distortion The preamplifier The output is transformerless and signal balanced between
6. only valid for DPA but also its suppliers With respect to waste disposal DPA fully complies with the WEEE directive 9002 96 EQ and will adhere to any amendments and subsequent requirements From 1 Janu ary 2006 all DPA products that require a return for upgrading and or reuse have been provided with a waste label This means that at the end of its usable life the product may be returned to the local DPA representative who will return it to DPA for disposal under the national legislation program Furthermore DPA guarantees that any DPA product purchased after 1 January 2000 will be covered by the same program to ensure that end users have adequate means to dispose of obsolete DPA products September 2007 DPA Microphones A S Product features and specifications are subject to change without notice Telefon 3946 0000 fax 3946 0040 www interstage dk pro audio with a smile interstage E Phistersvej 31 2900 Hellerup Danmark w DPA MICROPHONES DPA Microphones A S Gydevang 42 44 DK 3450 Alleroed Denmark Te 45 4814 2828 Fax 45 4814 2700 info dpamicrophones com www dpamicrophones com L10bvIdd
Download Pdf Manuals
Related Search