User Manual
Contents
1. document is not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2013 All Rights Reserved Introduction The Industrial Ethernet switch with POE feature complies with IEEE802 3af and IEEE802 3at it delivers 30watts power per POE port and generates total 120 watts power to PD devices and 2 SFP slots are supported The Industrial Ethernet switch provides power input voltage 48Vdc especially for IP surveillance traffic monitoring and for a broad range of applications It can be used as a stand alone device for buses trucks and other vehicles for Surveillance purposes With IP 30 standard industrial case protection allows either DIN rail or wall mounting for efficient use of cabinet space Wide operating temperature range 40 C to 75 C for harsh environment Key Features Supports P S E based on IEEE 802 3at up to 30 Watts per port SFP port supports 100Base FX and 1000Base X speed Support 48VDC power inputs for power redundancy Supports auto negotiation and auto MDI MDI X Supports store and forward transmission Supports flow control Rigid IP 30 housing design DIN Rail and wall mounting enabled Package Contents 1 x Industrial Switch 1 x User Manual 1 x 6 pin Terminal Block 2 x2. setting to select port 5 as TX disable port 5 SFP or set SFP speed to 100M The detail setting as shown below Warning OFF DIP to select F5 OFF port 5 SFP fascial F5 ON default Dip 2 to select SFP speed 1000M default Dip switch function will not work if it is changed when power is connected Always turn off or disconnect power supply to change dip switch settings Power connection This unit provides 6 pin terminal block And it can be operated using either 48VDC power source Input voltage varies by models please check the label on the side of this unit to determine the exact power input voltage for each model The VDC power range can be 48VDC only Always Make sure your input voltage is within this supported voltage range for each model vuuUUUUY vuuUuU pa rm pre m we 1 2 as WARNING salilla Any exceeded input voltage will not make this veve va F unit function and may damage this unit ANANNANANANNA N e NNNNA To make power connection Follow the printed polarity for V1 V1 V2 V2 and ground Connect positive wire to V connect negative wire to V also connect neutral wire to the ground screw as shown Relay You may use 24V 1A relay connection to your external device for special purpose When 2 powers are connected the relay is in SHORT mode When any power source fails the relay change to OPEN status Power connecting procedure STEP 1 Pull
3. User Manual Industrial Gigabit Switch 4 Port 802 3at PoE with 2 port SFP slot v1 0 P N 41NE IPG40200 A00 FCC MARKING This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE MARKING This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this
4. Wall Mounting Bracket and 4 x Screws 1 x Din Rail Bracket Compare the contents of the industrial switch with the standard checklist above If any item is damaged or missing please contact the local dealer for service Physical Dimension Back view 2 50 Top view LED Indicators Bottom view For definitions of LED indicators please refer to the following table LED Status Indication PW1 Green when V1 V1 is connected Off Power is off PW2 Green when V2 V2 is connected Off Power is off ERR Amber connect only PW1 or PW2 OFF both PW1 and PW2 are connected LNK Green TX link is detected OFF TX port is not detected Flashing TX port is active SPD Green 1000M speed is detected OFF 10M or 100M speed is detected P1 P2 P3 P4 Green PD is detected on designated port OFF no PD is detected F5 Green port 5 SFP fiber is detected OFF port 5 SFP fiber is not detected Flashing port 5 SFP fiber is active F6 Green port 6 SFP fiber is detected OFF port 6 SFP fiber is not detected Flashing port 6 SFP fiber is active Dip switch function This unit is equipped with dip switches located on the front panel Adjusting the dip switches will change the default function of this unit This unit has set to manufacturer default as Port 5 SFP and the speed is set to 1000M for both port 5 and port 6 SFP ports you may adjust dip switch
5. n SPD Speed 10 100 OFF 1000 Green SFP Fiber Per port Link Green Active Flash DIP 1 OFF Port 5 SFP ON DEFAULT ON Port 5 SFP OFF RE E DIP 2 OFF SFP 1000M DEFAULT ON SFP 100M Reserve polarity Pr sent protection Overload current Present protection Power Supply Redundant DC 48V Power Input Power Consumption 5 6W 48 VDC Non POE Alarm Relay Contact Relay outputs with current carrying capacity of 1A 24VDC Relay in short circuit mode when 2 powers are connected in open circuit mode when only one power supply is connected PoE power budget Removable Terminal Block Per port 30W Max 36W per port at 48VDC input Max 126W 48VDC power input Provide 2 Redundant power Alarm relay contact 6 Pin POE efficiency 48VDC Surface temperature Surface temperature rises 6 C full load in a 75 C chamber Operating Temperature 40 C 75 C Storage Temperature Operating Humidity 40 C 85 C 5 to 95 Non condensing Housing Rugged Metal IP30 Protection Dimension 142 x 43 x 105mm LxWxD Installation mounting DIN Rail mounting and Wall Mounting EMC EMS CE FCC EMI FCC Part 15 Subpart B Class A CE EN 55022 Class A
6. out 6 pin terminal block STEP 2 Connect wire to V1 V1 or V2 V2 and Ground the neutral wire to the ground screw STEP 3 Plug back 6 pin terminal block to its place WARNING Always ground the power source to maintain a clean power input Due to too many cheap made power supplies it creates too much noise and it will cause the power input fluctuates when connect to this unit To avoid this always ground the power source to gain a clean power input Specification Standards IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base TX Fast Ethernet IEEE 802 3ab 1000Base T Gigabit Ethernet IEEE 802 3z 1000Base X Gigabit Ethernet IEEE802 3x Flow Control and Back Pressure IEEE802 3af for POE IEEE802 3at for POE Switch Architecture Back plane Switching Fabric 12Gbps Data Processing Store and Forward Flow Control IEEE 802 3x Flow Control and Back Pressure Jumbo Frame 10KB MAC Table Size 1K Packet Buffer Size 1Mbits Network Connector 4 RJ 45 Port 10 100 1000BaseT X auto negotiation 4 Giga POE 802 3at af PSE port Auto MDI MDI X function Full Half duplex 2 SFP slots 100 1000M Base X Network Cable UTP STP above Cat 5e Cable EIA TIA 568 100 ohm 100m Fiber Cable Multi mode 50 125um 62 5 125um Fiber Cable Single mode 9 125um Protocol CSMA CD PW1 Power 1 Green PW2 Power 2 Green ERR Fault Amber LED TX RJ 45 port LNK Link Active Gree
Download Pdf Manuals
Related Search