User Manual
Contents
1. hot water supply line Is the hot water supply line open Is the hot water system activated Is the mesh filter ok Are the cold and hot water supply lines correctly connected 2 LED color ring is illuminating GREEN Check if NO water flows Water flows Device is broken Email technical blubathworks com 3 LED color ring is illuminating BLUE Check if cold water flows NO cold water is flowing Check the cold water supply line Is the cold water stop valve opened Is the mesh filter ok Are the cold and hot water supply lines correctly connected blu BATHWOR K S 1 866 907 0122 2015 10 blubathworks com Diagnostic completed Flashing 2x ORANGE Diagnostic successfully completed Flashing 3x ORANGE Malfunction of the temperature sensors Email technical blubathworks com Flashing 4x ORANGE Malfunction of the flow rate sensors Email technical blubathworks com Troubleshooting if LED color ring is NOT illuminating Please check the cable connection between control mixer TEEO3O amp wheels If you were unable to resolve the issue please email technical blubathworks com or call 1 866 907 0122 Special functions Press amp hold Wheel 1 until LED color ring is flashing TURQUOISE Release wheel immediately Flashing 1x TURQUOISE Special functions activated Flashing 2x TURQUOISE Special functions locked Changing between activation locking device press amp hold Wheel 1 until2. saved average temperature water flow and filling quantity which was last set Reset Quick Access Special function must be activated Quick Access 1 Quick Access 2 Quick Access 3 Press Wheel 1 once x1 Press Wheel 1 twice briefly x2 Press Wheel 1 three times briefly x3 Water ON like Quick Access 1 Water ON like Quick Access 2 Water ON like Quick Access 3 Press amp hold Wheel 1 until LED color ring is flashing DARK BLUE Release wheel immediately Flashing 2x DARK BLUE Water OFF reset settings filling quantity is deactivated temperature and water flow like factory setting Diverting handshower tubfiller Press Wheel 1 once x1 Water ON Press Wheel 2 briefly Diverting tub filler lt gt handshower bli 2015 10 BATHWORKS 1 866 907 0122 blubathworks com Anti scald protection Turn Wheel 1 Changing temperature from 100 F 38 C temperature increase in smaller increments more wheel turns Activating the cleaning mode Deactivating wheels functions Press amp hold Wheel 1 until LED color ring is flashing GREEN Release wheel immediately Reactivating wheels functions Press amp hold Wheel 1 until LED color ring GREEN goes out or wait 60 seconds automatic reactivation Diagnostic Press amp hold Wheel 1 until LED color ring is flashing ORANGE Release wheel immediately Start Diagnostic 1 LED color ring is illuminating RED Check if hot water flows NO warm water is flowing Check the
3. DUO 1 Control Wheel User Manual EP421 TEP431 TEU431 PT 7003 PT 7004 for bath application with temperature and water flow sensor bli 2015 10 BATHWORK S 1 866 907 0122 blubathworks com Important Safety Information The user manual must be given to the user Please read this user manual carefully before using the system and keep in a safe place for future reference To reduce the risk of injuries scalding and electrical shock the safety precautions must be installed and followed as per install guide A WARNING Risk of injury This device is not intended for use by persons including children with different or reduced physical sensory or mental abilities or who lack experience or knowledge unless they are under the supervision of or receive training for the use of the device by a person responsible for their safety Children should be under supervision at all times to ensure that they do not use devices as toys CONTINUOUSLY TURNING THE CONTROL WHEEL IN THE CLOCKWISE DIRECTION MAY OVERRIDE THE PRE SET MAXIMUM TEMPERATURE RESULTING IN A RISK OF SCALDING If the power cord gets damaged it must be replaced by the manufacturer its authorized service agent or qualified personnel to avoid danger Never operate the device with a damaged cable or plug Do not pull on the power cable as this could cause damage to the cable and cause electric shock Troubleshooting Malfunctions Possible Cause Solution The
4. LED ring is flashing TURQUOISE Release wheel immediately Thermal disinfection Special function must be activated ATTENTION RISK of scalding Run Disinfection Press amp hold Wheel 1 until LED color ring is flashing RED Release wheel immediately Flashing RED Flushing with hot water Stop Disinfection Press Wheel 1 once or wait 2 minutes automatic stop Factory setting Special function must be activated Press amp hold Wheel 1 until LED color ring is flashing BLUE Release wheel immediately Flashing 2x BLUE Factory settings restored bli 2015 10 1 866 907 0122 blubathworks com BATHWOR K S
5. device is not working Start Diagnostic Check that 1 The control unit is connected to the mains 2 There is no power supply failure 3 The electric plug inside the control unit is well connected Check that 1 Your faucet is well connected to the water supply 2 Both angle valves are fully opened 3 On another faucet in the house if you have water supply 4 The water supply hoses are not bent or twisted 5 The supply hoses might be soiled No water flow when activated 6 The control unit is connected to the mains Minimal water flow Check that 1 Both angle valves are fully opened 2 The water supply hoses are not bent or twisted 3 The supply hoses might be soiled Continuous water flow Press the ON OFF button Close access to water After a few minutes open again It s still a continuous water flow close access to water and contact your installer Maintenance Use soft cloth soapy solution and water for regular care Wipe with a dry cloth Avoid the use of abrasives or solvents which damage the surface Damage caused by inappropriate treatment by the user is not covered by our guarantee bli 2015 10 BATHWORKS 1 866 907 0122 blubathworks com Explanation of wheels Functions WHEEL 1 ON OFF Changing the water temperature WHEEL 2 Change water flow Diverting tub lt handshower tubtfiller Basic Functions 1 Water ON Press Wheel 1 once 1x Water ON 2 Changi
6. ng water temperature Turn Wheel 1 when water ON Change temperature according to LED color ring blue cold orange warm red hot 3 Changing water flow Turn Wheel 2 when water ON Change water flow 4 Divert between functions Press Wheel 2 once 1x Divert between handshower and tub filler 5 Water OFF Press Wheel 1 once 1x Water OFF blu BATHWOR K S 1 866 907 0122 2015 10 blubathworks com Quick Access for bath Quick Access 1 factory setting Press Wheel 1 once 1x Water ON by 95 F 35 C and 100 water flow Quick Access 2 factory setting Press Wheel 1 twice briefly x2 Water ON by 100 F 38 C and 100 water flow Quick Access 3 factory setting Press Wheel 1 three times briefly x3 Water ON by 107 5 F 42 C and 100 water flow Saving Quick Access Quick Access 1 Quick Access 2 Quick Access 3 Press Wheel 1 once x1 Press Wheel 1 twice briefly x2 Press Wheel 1 three times briefly x3 Water ON like Quick Access 1 Water ON like Quick Access 2 Water ON like Quick Access 3 Start tub filling measurement 2 6 gallons 10 liters of water will be filled automatically Turn Wheel 1 Change water temperature as desired Turn Wheel 2 Change water flow as desired Fill desired water quantity When the tub is filled to the required water level press amp hold Wheel 1 until LED color ring is flashing PURPLE Release wheel immediately Flashing 2x PURPLE Water OFF setting is
Download Pdf Manuals
Related Search