User Manual
Contents
1. er is installed in a wet environment 13 Protection This controller has full protection for ouput short circuit overload and overheat The controller will automatically recover from protection when working status is good Please ensure the LED loads are in rated range outputs are not shorted and the controller unit is in a good heat dissipation environment to avoid damage FCC Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 4400 Earth City Expy St Louis MO 63045 m 866 590 3533 User Manual Part Number MCBRF VCT7 X support superbrightleds com2. euperinigiticds ccm Important Read all instructions prior to installation RGB LED Controller with Wireless RF Remote Parts Included 1 LED Controller 1 Wireless Remote Specifications 1 CR2025 3V Battery Color Temp Grade 7 levels Working Voltage DC 5 24V Battery 3V CR2025 Remote frequency 433 92MHz Remote control distance gt 15m at open area Rated Output Current 2x7A IP Rating IP68 FCC ID 2ACJPRM03 Wireless Remote Functions 1 Turn On Standby Press l key to turn on unit or press O key to turn off Retains last setting between power off and power on 2 Color Temperature Adjust To control color temperature press C T key to increase color temperature by increasing the cool white channel output power and decreasing warm white channel output power Press C T key to lower color temperature by increasing warm white channel output power and decreasing cool white channel output power The overall brightness will remain unchanged when adjusting color temperature 3 Brightness Adjust Press BRIGHT key to increase brightness and BRIGHT to decrease brightness The color temperature will remain unchanged when adjusting brightness 4 Brightness Shortcut Press one of the shortcut buttons to set the relative shortcut brightness level 3 shortcut keys 10 50 and 100 are available 5 Color Temperature Shortcut Press one of
3. low flash reach speed or brightness limit Red flash overload protected Yellow flash overheat protected Remote Pairing Options 10 Using Remote Prepare the wireless remote for use by removing the battery insulator The remote uses a 3V CR2025 battery Note The wireless remote operates using radio frequency RF The remote s use is not restricted by normal obstructions such as walls doors etc Do not install controller in metal enclosures 11 Pairing New Remote The remote controller and main unit are 1 to 1 paired as default Further more one main unit can be paired to 5 remotes and every remote can be paired to any controller Please do the following steps to pair a new remote to the controller 1 Remote power of the controller and restore power again after 5 seconds 2 Press remote C T and C T key together in 5 seconds after power is restored After this operation the main unit indicator will flash white 3 times the master unit now recognizes the new remote Only 5 latest paired remote controllers can be recognized by main unit m 866 590 3533 X support superbrightleds com euperinigiticds ccm Important Read all instructions prior to installation RGB LED Controller with Wireless RF Remote Advanced Features 12 Waterproof This controller is fully waterproof with IP68 standard and can be used under water within the depth of 30 meters Note The remote receiving sensitivity will decrease when the controll
4. the shortcut buttons to directly select the relative color temperature 3 shortcut keys Warm Neutral and Cold are available Warm and Cold is pure warm or cool output Neutral is half warm and half cool output 6 Wireless Remote LED Indicator Flashes blue when remote is operating to indicate that the remote is functioning properly Ga 4400 Earth City Expy St Louis MO 63045 User Manual Part Number MCBRF VCT7 Vays cap Warm Neutral Cold _ s gt _ WF 10 50 100 a ae L RF Wireless JD Controller Installation 7 Power Supply Wiring The controller power supply operates at 5 24VDC The red wire is positive and the black wire is negative as indicated on the controller housing Make sure the power voltage matches the LED strip requirement Incorrect voltage may damage the LED strip 0 To LED Strip To Power Supply 8 LED Output Wiring The black cable on the output side should be connected to LED positive the white cable should be connected to cool white LED s negative and the yellow cable connected to warm white LED s negative 9 Status Indicator This is a full color status indicator It displays all working statuses of the controller It indicates different events as following Blue normal working Short single white flash new command executed Long single white flash reach mode or color cycle edge Long single yel
Download Pdf Manuals
Related Search