Home
CT-10x Compact Transmitter - User Manual
Contents
1. CT 10x Compact Transmitter User Manual The CT 10x series of compact transmitters are designed to send pre programmed alphanumeric messages or commands to compatible wireless receivers such as pagers alphanumeric LED displays or other wireless controllers When set to System Monitored mode the CT 10x compact transmitters send a coded message to a receiver connected to a compatible monitoring system that analyzes the content of the coded message and initiates the respective action according to its internal programming The CT 10x messages and alerts can be triggered using the push buttons dry contact closure door magnet sensor or horizontal position sensor Each one of the triggers applicable to the device can be programmed with its own unique message or alert and activate one or multiple wireless receivers Operation Note The CT 10x compact transmitters are fully programmable using the VPS software Please refer to the Software amp Programming section below for more information Follow these steps to activate the CT 10x compact transmitter 1 Confirm that the CT 10x is programmed with the identical parameters of the wireless receiver frequency baud rate message type polarity capcode etc Note use the VPS software to read the CT 10x parameters and modify them as required 2 Activate the trigger s applicable to your device press a button close the dry contact closure separate the external door magnet from the CT 10x or c
2. by for sage Active V Program Cancel Alert Capcode 0800100 Auto Increment by 01 Message ae el V Active V Program Monitoring Alert Capcode 0800500 Auto Increment by 01 Message Monitoring Supervision Elevated IV Active Le Elevated Alert Interval None hd Alert Repeat Count None Alert Repeat Interval iMinute v Delayed Activation Interval None Y V Send Low Battery Alert Version 1 00
3. hange the CT 10x to the horizontal position 3 Verify that the alphanumeric message is displayed on the respective receiver or that the receiver executed the wireless command play pre programmed tone stored in its memory turn on strobe light etc For system monitored devices verify that the monitoring system received and processed the coded message In addition to the messages and alerts generated by the device triggers the device can also generate status and monitoring messages These messages are listed below 1 Cancel Alert generated when the CT 10x is reset to normal status Depending on the purchased device configuration Cancel status occurs when a magnet is swiped next to the left side of the CT 10x a dry contact closure is opened an external door magnet is placed back next to the CT 10x or when the CT 10x is returned to vertical position 2 Monitoring Alert generated by the device when supervision elevated alert low battery or malfunction events occur If Supervision and Elevated alerts are activated their respective time interval is also user programmable 3 Repeat If activated the original message is repeated as long as the CT 10x has not been reset to the Normal status The number of repetitions and the time interval between each repetition is user programmable Battery Replacement The CT 10x compact transmitters uses standard CR 2 lithium battery Follow these steps to replace the battery 1 Remove the 4 screws fr
4. ogramming screen is not displayed click on the Wireless Devices toolbar menu and then click on CT 1xx Compact Transmitter Programmer Click on Read to read the CT 10x parameters For more information and details regarding each field and feature press F1 on your keyboard or click on Help requires installing the Help support update as shown on step 10 10 Install the Help support update for Windows 7 and up 10 1 Click on the Help menu 10 2 Click on Help Support Compatibility Download Link and follow instruction on the screen Version 1 00 a Dad vv ee VS1810 VS4810 Wireless Devices Help Settings Connected to CT 1XX on COM 10 38400 N 8 1 CT 1xx Compact Tran EET Close NE Read Ep Program 2 Help Device panam Version 0 01 05 Serial Number p Battery Level V 3 00 Frequency Range 427 470 MHz Continuous Programming Mode gt Transmitter Settings Transmitter Mode Direct Page to Receiver Frequency 467 6500 Deviation 2 5 kHz z Error 4 Mode 0 Message Type Alphanumeric Baud Rate 1200 Polarity Standard z Programmable Messages IV Program Button 1 Capcode 0800100 Auto Increment by 01 Message Buttoni S Adie I Program Button 2 Capcode 0000000 I Auto Increment by for Message y O OE T Active Program Button 3 Capcode 0000000 l Auto Increment by for Message Ce I Active E Program Button 4 Capcode foooo000 Auto Increment
5. om the back cover and carefully separate the back cover from the front cover 2 Identify the installation polarity and direction of the installed battery 3 Remove the old battery and install the new battery following the same polarity used by the old battery and according to the marking on the plastic case and circuit board on battery should match the on the CT 10x board Warning Incorrect polarity may cause permanent damage to the CT 10x and is not covered under warranty If the device is not operational or the new battery feels hot to touch remove the battery immediately 4 Replace the back cover on the front cover and use the 4 screws to secure them together Hand tighten the screws to avoid damage to the case Version 1 00 Software amp Programming The VPS software allows you to program the CT 10x messages and features using an optional USB cable A Male to Mini B Male Follow these steps to install the VPS software and USB drivers Note Do not connect the CT 10x to the PC at this point 1 2 7 8 Log in to PC as a user with administrator privileges Download the VPS software www visiplex com docs vps_ setup exe and save it to the PC desktop or Downloads folder Install the VPS software Install USB drivers applicable to the Windows OS x86 or x64 i e 32 bit or 64 bit from the shortcuts under the VPS program group under the Windows start menu Remove the 4 screw securing the back and front co
6. vers Make sure that battery is installed properly Identify the COM number on the PC used for communication with the CT 10x 6 1 Open Windows Device Manager and expand the Port COM amp LPT section Connect the CT 10x to the PC using the USB cable and note the COM number newly assigned to the installed device on Windows Device Manager Windows may also display a system notification indicating the installed COM port in the notification area next to the system clock Note If the COM number is higher than 16 you will need to re assign a different COM port to this USB connection Right click on the COM port click on Properties Port Settings Advanced Change the COM Port Number to a number between 4 and 16 and click OK you may ignore any warning messages Run VPS software and allow it to auto detect the connected device and serial COM port used Note If communication cannot be established or faster connection initialization is preferred configure the VPS to use assigned COM port for communication with the device 7 1 Click on the Settings menu 7 2 Click on the Configuration amp Settings menu item 7 3 In the Serial Port drop down list select the COM noted on step 6 7 4 Clear the Auto Detect Connected Devices on Startup check box 7 5 Click on Save If connection is successful the VPS software information bar under the Settings menu will display the connection details and the CT 1xx programming screen will be displayed Note If the pr
Download Pdf Manuals
Related Search
Related Contents
World Marketing of America NTK15 space heater 4 - VThunder Quick Start User Guide EstEID ID – card specification 113827_somario_BG-DE-GR-HR-BA-SP .indd Copyright © All rights reserved.
Failed to retrieve file