User Manual - SABiosciences
Contents
1. Antibodies Store at 4 C Store at 20 C f DILUTION COMPONENTS COMPONENTS FACTOR 2 Anti Phospho Protein Specific 10x Antigen Retrieval Buffer Antibody 1 100 10x Washing Buffer Anti Pan Protein Specific Antibody 1 100 Antibody Dilution Buffer Blocking Buffer dry powder Cell Staining Solution Developing Solution Secondary Antibody s Stop Solution Washing Buffer Reservoir 4 t4 Dilute 1 16 before use Each antibody stock must be freshly diluted into Antibody Dilution Buffer on the same day of the experiment Use Dilution Factor specified for each antibody on its Product Information sheet See page 9 for more details 210x Washing Buffer and 10x Antigen Retrieval Buffer must be diluted to 1x with distilled H20 before use 3Just before use dissolve powder in 30 ml 1x Washing Buffer by mixing well Once dissolved Blocking Buffer may be stored at 4 C for up to two 2 weeks Catalog number FE 015 the CASE Kit for p53 S15 contains two Secondary Antibodies Secondary Antibody A must be used with the Pan Protein Specific Primary Antibody and Secondary Antibody B must be used with the Phospho Protein Specific Primary Antibody Shipping and Storage Conditions Box 1 is shipped at ambient temperature and should be stored at 4 C Box 2 is shipped on dry ice and should be stored at 20 C Shelf Life All reagents are stable as is if it is not used for 6 months after receipt of the kit and stored2. at 4 C In this way you can accumulate many plates in the refrigerator and perform the CASE assays later when desired NOTE To minimize cell loss during all of the wash steps in the following protocol never dispense liquid directly onto the cell surface Instead gently touch the pipet tips to and gently dispense the liquid down the wall of cell culture wells always using the same side of the wells To remove wash solutions flip the plate over a sink and then tap the plate gently onto a paper towel to remove any remaining liquid From this point forward avoid the use of vacuum suction to remove solutions from the plate Technical Support support SABiosciences com www SABiosciences com 12 Version 2 7 Remove the Cell Fixing Buffer and wash cells twice with 200 ul of 1x Washing Buffer for 5 minutes each with rocking Remove Washing Buffer add 100 ul of Quenching Buffer and incubate for 20 minutes at room temperature Remove Quenching Buffer and wash cells once with 200 ul of 1x Washing Buffer for 5 minutes with rocking Remove the Washing Buffer and add 100 ul of 1x Antigen Retrieval Buffer With the lid off place the plate into a microwave oven Microwave the plate at 375 Watts for 3 minutes Calculated the appropriate power setting to deliver this wattage from your microwave For instance 30 power or level 3 delivers 375 W using a 1250 W microwave Carefully remove the plate from the microwave oven cover the plate
3. solution from the washing buffer reservoir avoid pipetting air bubbles and examine the plate before placing into your ELISA plate reader Carefully break any air bubbles with a pipet tip 3 Improper antibody incubation and washing Be sure to fill all wells with the appropriate antibody and follow the recommendations for washing Use a rocker in every wash step H No antibody solution in wells after overnight incubation Be sure to seal the open plate with sealing tape then with a piece of parafilm and place the lid onto the plate The plate may also be stored in a zip lock or heat sealed bag Be sure to store the plate on a level stable surface If you have additional questions please check our website www SABiosciences com for a more complete listing of Frequently Asked Questions FAQs or call our Technical Support Representatives at 1 888 503 3187 or 301 682 9200 Technical Support 888 503 3187 US 301 682 9200 19 CASE Cellular Activation of Signaling ELISA Part 1013A Version 2 7 3 2 2009 fy SABiosciences Focus on Your Pathway 888 503 3187 301 682 9200 www SABiosciences com support SABiosciences com
4. the planned experiment If you use the antibodies wisely enough material is provided in the kit to process a total of 96 assays or in other words 96 wells with each primary antibody and a total of 2 x 96 192 wells with the secondary antibody Volume of Diluted Antibody Prepared in Antibody Dilution Buffer Diluted Antibody 8 assays 12assays 96 assays Anti Phospho Protein Specific Primary Antibody 900 pl 750 ul 6000 ul Anti Pan Protein Specific Primary Antibody 500 ul 750 ul 6000 ul Secondary Antibody 2000 ul 3000 ul 24000 ul Both primary antibodies in all CASE Kits should be diluted by a factor of 1 100 The secondary antibody s in all CASE Kits should be diluted by a factor of 1 16 FOR EXAMPLE f the required dilution factor for an anti phospho protein specific antibody is 1 100 and 12 assays are to be performed calculate the amount of stock antibody to dilute 750 ul from table above 100 dilution factor 7 5 ul Thus 7 5 ul of antibody should be diluted into 750 ul of Antibody Dilution Buffer Perform this calculation separately for both primary antibodies and the secondary antibody using their dilution factors and the total volumes in the table above NOTE For catalog number FE 015 the CASE kit for p53 S15 only make half of the recommended volume of the above dilution for each of the two included Secondary Antibodies A for use with the Pan Protein Specific Primary Antibody and B for use with the Pho
5. with its lid and allow it cool to room temperature Remove Antigen Retrieval Buffer and wash cells once with 200 ul of 1x Washing Buffer for 5 minutes with rocking Remove the Washing Buffer add 100 ul of Blocking Buffer and incubate for 1 hour at room temperature Technical Support 888 503 3187 US 301 682 9200 13 CASE Cellular Activation of Signaling ELISA C Incubation with Primary and Secondary Antibodies 1 Remove Blocking Buffer and wash cells once with 200 ul of 1x Washing Buffer for 5 minutes with rocking Remove Washing Buffer and add 50 ul of diluted primary antibody either the phospho protein or the pan protein specific antibody to each appropriate well See page 9 for antibody dilution instructions To the negative control wells add 50 ul of Antibody Dilution Buffer instead Cover the plate with its lid and incubate at room temperature for 1 hour Remove the primary antibody and wash cells twice with 200 ul of 1x Washing Buffer for 5 minutes each with rocking Remove the Washing Buffer and add 100 ul of dilute secondary antibody to each well Incubate for 1 hour at room temperature Meanwhile transfer only the needed amount of Developing Solution 100 ul per well into a clean Washing Buffer Reservoir and allow it to warm to room temperature while protected from light NOTE For catalog number FE 015 the CASE kit for p53 S15 be sure to add the dilution of Secondary Antibo
6. 10 C Incubation with Primary and Secondary Antibodies 14 D Colorimetric Detection 15 E Determination of Relative Cell Number 16 V Troubleshooting Guide 17 Method Reference Versteeg HH Nijhuis E van den Brink GR Evertzen M Pynaert GN van Deventer SJ Coffer PJ Peppelenbosch MP A new phosphospecific cell based ELISA for p42 p44 mitogen activated protein kinase MAPK p38 MAPK protein kinase B and cAMP response element binding protein Biochem J 2000 Sep 15 350 Pt 3 717 22 LIMITED PRODUCT WARRANTY This warranty limits our liability to replace this product in the event the product fails to perform due to any manufacturing defect SABiosciences Corporation makes no other warranties of any kind expressed or implied including without limitation warranties of merchantability or fitness for a particular purpose SABiosciences Corporation shall not be liable for any direct indirect consequential or incidental damages arising out of the use the results of use or the inability to use this product NOTICE TO PURCHASER This product is intended for research purposes only and is not intended for drug or diagnostic purposes or for human use The purchase of a CASE Kit includes a limited nonexclusive license to use the kit components for research use only This license does not grant rights to use the kit components for reproduction of any kit component to modify kit components for resale or to use a CASE Kit to manufacture commercial pro
7. A SABiosciences User Manual CASE Cellular Activation of Signaling ELISA Directly Monitor Protein Phosphorylation without Cell Lysis See Purchaser Notification for limited use license and warranty information page 3 Part 1013A Version 2 7 3 2 2009 SABiosciences Corporation 6951 Executive Way Frederick MD 21703 USA CASE Cellular Activation of Signaling ELISA Directly Monitor Protein Phosphorylation without Cell Lysis User Manual For Catalog Numbers FE 001 through FE 021 Ordering and Technical Service Contact Information e Tel 1 888 503 3187 US 301 682 9200 outside US e Fax 1 888 465 9859 US 301 682 7300 outside US e On line Order www SABiosciences com e E MAIL order SABiosciences com to place an order support SABiosciences com for technical support You may place orders by fax e mail or from our website Each order should include the following information Your contact information name phone email address Product name catalog number and quantity Purchase order number or credit card information Visa or MasterCard Shipping address Billing address For more information visit us at www SABiosciences com SABiosciences Corporation 6951 Executive Way Suite 100 Frederick MD 21703 USA CONTENTS l Background and Introduction 4 ll Materials Provided 6 Ill Additional Materials Required 7 IV Protocol 8 A Working Solution Preparation 8 B Cell Culture and Preparation
8. Prepare either 4 or 8 Cell Fixing buffer depending on the type of your cell culture Volume for 96 Cell Fixing Buffer Reagent wells of Elvi 1x PBS 10 7 ml me ea ik 37 Formaldehyde 1 3 ml Total Volume 12 ml OR of Fixi 1x PBS 9 4 ml ds dpa biel cells 37 Formaldehyde 2 6 ml P Total Volume 12 mi WARNING Formaldehyde and its vapors are highly toxic Always prepare and use formaldehyde solutions under a chemical fume hood and wear protective gloves and eyewear and a lab coat Dispose formaldehyde waste according to your institution s hazardous waste disposal protocol 2 1x Washing Buffer 10X Washing Buffer must be diluted to 1x with distilled H2O before use 3 Quenching Buffer To 11 48 ml of 1x Washing Buffer add 400 ul of 30 H20 and 120 ul of 10 NaN for a final volume of 12 ml enough for 96 wells 4 1x Antigen Retrieval Buffer 10x Antigen Retrieval Buffer must be diluted to 1x with distilled dH2O before use 5 Blocking Buffer Just before use dissolve blocking buffer powder provided in kit box 1 in 30 ml 1x Washing Buffer by mixing well Once dissolved Blocking Buffer may be stored at 4 C for up to two 2 weeks Technical Support support SABiosciences com www SABiosciences com 8 Version 2 7 6 Antibody Dilution Each antibody provided in the kit must be freshly diluted using Antibody Dilution Buffer each time the experiment is performed Dilute just enough of the antibodies as needed for
9. The following solutions are required for performing the CASE assay but are not included with the kit These solutions must be prepared from materials obtained from other manufacturers before starting the CASE procedure 1x Phosphate Buffered Saline PBS Dissolve 8 0 g of NaCl 0 2 g of KCI 1 44 g of Na2HPOa and 0 24 g of KH2PO in 800 ml of distilled H2O Adjust the pH to 7 4 Bring the final volume to 1 liter with distilled water Dispense in convenient volumes and sterilize by autoclaving Store at room temperature 37 Formaldehyde Molecular Biology Grade from any chemical supplier For example Sigma Cat No F8775 30 H20 concentrated hydrogen peroxide Molecular Biology Grade from any chemical supplier For example Sigma Cat No H1009 10 NaN sodium azide Dissolve 10 g of sodium azide into 100 ml of ddH20 Use appropriate caution sodium azide is a hazardous substance 1 SDS sodium dodecyl sulfate Dissolve 1 g of sodium dodecyl sulfate into 100 ml of ddH20 Store at room temperature Technical Support 888 503 3187 US 301 682 9200 7 CASE Cellular Activation of Signaling ELISA IV Protocol Please familiarize yourself with the entire CASE Kit protocol before starting the experiment A Working Solution Preparation The following working solutions should be freshly prepared from the stock solutions each time the experiment is performed using the following recipes 1 Cell Fixing Buffer
10. and examine the plate before placing into your ELISA plate reader Carefully break any air bubbles with a pipet tip WARNING The Stop Solution is corrosive Always wear protective gloves and eyewear and a lab coat when handling this solution 5 Within 5 minutes read absorbance at 450 nm on an ELISA Plate Reader Blank the instrument according to the manufacturer s instructions Technical Support 888 503 3187 US 301 682 9200 15 CASE Cellular Activation of Signaling ELISA E Determination of Relative Cell Number 1 Remove the assay solution as described above Wash the wells once with 200 ul of 1x Washing Buffer for 5 minutes with rocking Wash the wells once with 200 ul of dH20 for 5 minutes with rocking Be sure to remove any excess liquid by tapping plate gently on paper towel Air dry at room temperature for 5 minutes 2 Add 100 ul of Cell Staining Buffer to each well and incubate for 30 minutes at room temperature WARNING The Cell Staining Buffer is an intense stain Avoid contact with skin and clothing 3 Rinse the plate twice with 200 ul of dH20 and then wash the wells twice with 200 ul of dH2O for 5 minutes each with rocking NOTE Wash out as much of the residual color as possible to insure that the OD595 reading will reflect the real cell number 4 Add 100 ul of 1 SDS to each well and incubate on a rocker for 1 hour at room temperature NOTE Large air bubbles in the 96 well plate can significant
11. at the recommended temperature Technical Support support SABiosciences com www SABiosciences com 6 Version 2 7 lll Additional Materials Required The following supplies are also required but are not included as part of the CASE kit Multi Channel Pipettor Parafilm Rocking platform Microwave oven ELISA Plate Reader or spectrophotometer capable of reading at 450 and 595 nm Tissue Culture Plates Choose the type of tissue culture plate that is best suited to your cell line and treatment 96 Well Clear Flat Bottom TC Treated Microplate Corning Costar 3595 CellIBIND 96 Well Clear Flat Bottom Polystyrene Microplates Corning Costar 3300 96 Well Clear Flat Bottom Poly D Lysine Coated Microplate Corning Costar 3665 NOTE Because the entire CASE protocol occurs directly in tissue culture plates good cell attachment is essential for the success of the experiment The TC treated plates provide the lowest non specific background while the CellIBIND and poly D lysine coated plates provide better cell attachment but sometimes also generate a higher non specific background signal For tightly attached adherent cells such as A431 we recommend using the TC treated plates For more loosely attached adherent cells such as NIH 3T3 or HEK 293 or for suspension cells we recommend using the CellBIND or poly D lysine coated plates We highly recommend pre testing which type of tissue culture plate is best suited for your cell lines
12. cate wells are used here for each dose and time point Cells were treated with various concentrations 0 1 10 or 100 ng ml of IGF 1 with or without the kinase inhibitor LY294002 for 0 10 30 or 60 minutes The 96 well plate was used in a CASE Kit Assay half of the plate was treated with the anti pbhospho protein specific primary antibody and half with the anti pan protein specific primary antibody Eight wells of cells were not treated with primary antibody but only with secondary antibody 2 Antibody ONLY and eight wells were not plated with cells but were treated with both primary and second antibodies Blank The different shades in 96 well plate represent theoretical signal intensities from the experiment a Each treatment point or assay determination requires two sets of cells treated in an identical fashion One set of cells will be incubated with the phospho protein specific antibody to measure phosphorylated protein the other set of cells will be incubated with the pan protein specific antibody to measure total protein Each experimental condition e g time point concentration point etc should be performed in duplicate or triplicate to control for systematic variation Technical Support support SABiosciences com www SABiosciences com 10 Version 2 7 b You should also include wells for control purposes such as i Blank wells not seeded with any cells ii Detection control wells seeded with cells only incubated w
13. cient antibody sensitivity If the absorbance readings in the wells incubated with phospho protein specific antibody are significantly above background but do not change in response to your treatment then the ability to detect smaller changes can be improved by decreasing the concentration of anti phospho protein specific antibody to half Technical Support 888 503 3187 US 301 682 9200 17 CASE Cellular Activation of Signaling ELISA C Poor sensitivity low absorbance readings for antibodies Primary antibody concentration is too low For low protein expression levels as determined by Western analysis double the concentration of the primary antibodies and decrease the incubation volume by half Take extra care in dispensing the smaller volumes and in sealing the plate to avoid evaporation D The Ags readings for the wells incubated with the phospho protein specific antibody are higher than the A450 readings from wells incubated with the pan protein specific antibody The phospho protein specific antibody is simply more sensitive than that the pan protein specific antibody This phenomenon occurs in several of our CASE Kits It does not affect your final assay results Remember that the CASE Kits do not involve a calibration curve and therefore can only be used for relative measurement E High background in all wells 1 Developing time too long Be sure to stop the colorimetric development as soon as the darkest positive well
14. ducts without written approval of SABiosciences Corporation No other license expressed implied or by estoppel is granted Technical Support support SABiosciences com www SABiosciences com 3 CASE Cellular Activation of Signaling ELISA Background and Introduction As an intracellular signal transduction pathway involving a protein kinase cascade is activated by an extracellular stimulus the extent of phosphorylation of an upstream regulatory protein increases Monitoring the phosphorylation status of this protein helps verify whether the stimulus activates the pathway and helps determine the effect of various treatments inhibitors or activators on that activation Two traditional methods are widely used to measure the phosphorylation status of a protein Western blot analysis with phospho specific antibody or P incorporation followed by gel electrophoresis Both methods are tedious require a large amount of cells and treatment reagents and are not suitable for high throughput studies The Cellular Activation of Signaling ELISA CASE Kits employ a cell based ELISA that directly measures protein phosphorylation on 96 well cultured cells The CASE Kits include a complete antibody based detection system for colorimetric quantification of the relative amount of phosphorylated protein and total target protein This simple and efficient cell based protein phosphorylation assay eliminates the need to prepare cell lysates and to perfo
15. dy A to the wells that held the Pan Protein Specific Primary Antibody and to add the dilution of Secondary Antibody B to the wells that held the Phospho Protein Specific Primary Antibody Technical Support support SABiosciences com www SABiosciences com 14 Version 2 7 D Colorimetric Detection 1 Remove the secondary antibody and wash cells twice with 200 ul of 1x Washing Buffer for 5 minutes each with rocking Then wash the cells once with 200 ul of PBS for 5 minutes with rocking 2 Remove the PBS and add 100 ul of Developing Solution pre warmed to room temperature into each well Protect plate from direct light Incubate for 1 to 10 minutes at room temperature 3 Monitor the blue color development until the darkest staining well turns a medium to dark blue DO NOT OVERDEVELOP ANY WELLS 4 Add 100 ul of Stop Solution into each well to stop reaction The Stop Solution turns the blue color to yellow NOTE Do not add Stop Solution to the Washing Buffer Reservoir that contained the Developing Solution Use a clean reservoir for Stop Solution Stagger the addition of the Developing and Stop Solutions in a manner that allows each well to develop for the same length of time NOTE Large air bubbles in the 96 well plate can significantly and artificially inflate your OD readings To avoid the appearance of air bubbles remove a sufficient volume of every solution from the washing buffer reservoir avoid pipetting air bubbles
16. hat you plan to use and prepare only as much antibody dilution as you need 2 Allow cells to grow overnight Then perform treatments as defined by your experiment on the next day NOTE Take special care when removing tissue culture medium by vacuum suction Cell loss while changing medium or treatment solutions is one of the most common causes of poor CASE assay results Use low vacuum pressure or attach an additional 200 sterile plastic pipet tip over your glass Pasteur pipet used for vacuum suction 3 Fix Cells a For adherent cells remove the culture medium and add 100 ul of 4 Cell Fixing Buffer to each well b For suspension cells directly add 100 ul of 8 Cell Fixing Buffer to the 100 ul of culture medium in each well To minimize formaldehyde evaporation seal the open plate with a piece of parafilm and place the lid onto the plate Incubate for 20 minutes at room temperature WARNING Formaldehyde and its vapors are highly toxic Always prepare and use formaldehyde solutions under a chemical fume hood and wear protective gloves and Technical Support 888 503 3187 US 301 682 9200 11 CASE Cellular Activation of Signaling ELISA eyewear and a lab coat Dispose formaldehyde waste according to your institution s hazardous waste disposal protocol You may use the fixed cells right away or the fixed cells are also stable for several weeks in Cell Fixing Buffer Seal with parafilm or in a zip lock bag and refrigerate
17. ith secondary but not primary antibody iii Experimental control wells seeded with cells but not experimentally treated c Seed cells into a 96 well plate the day before your treatment with the idea that the cell culture density should be at roughly 50 80 percent confluence on the day of your treatment and the CASE experiment See page 7 for recommendations on selecting tissue culture plates FOR EXAMPLE n the experiment outlined in Figure 2 cells are seeded at 2 0 x 10 cells per well on day 0 and allowed to sit and grow overnight On day 1 the cells are starved in serum free medium overnight On day 2 the relevant wells of cells are pre treated with the inhibitor for one hour followed by the IGF1 treatment as described in the figure legend Then the CASE assay protocol is performed as described below For the majority of cell lines with a doubling time of 18 24 hours seeding an initial density of roughly 1 5 x 10 cells per well will yield the appropriate cell density by the time of the CASE assay If you have not established a growth curve for your cell line in 96 well tissue culture plates perform a pilot cell seeding experiment before seeding cells for the CASE experiment Cell densities that are too high or too low at the time of the CASE assay give poor results Re seed cells if the cell growth or confluence conditions are not appropriate NOTE t is not necessary to plate cells in all 96 wells Only add cells to the wells t
18. ls on the plate using microscope and perform steps to Determine Relative Cell Number to measure how many cells remain on the plate Cells do not contain detectable levels of the target protein Verify expression of the protein in your cell line by Western analysis using a pan protein specific antibody B No response observed to experimental treatments in wells incubated with phospho protein specific antibody l Cells culture conditions are not appropriate When cells are not healthy i e the cell culture is not fresh or the cell density is too low or over confluent cells may not respond to your treatment properly Seed cells the day before your treatment so that the cell culture density is at roughly 50 80 percent confluence before your treatment If you have not established a growth curve for your cell line in 96 well tissue culture plates perform a pilot cell seeding experiment before seeding cells for the CASE experiment For the majority of cell lines with a doubling time of 18 24 hours seeding an initial density of roughly 1 5 x104 cells per well will yield the appropriate cell density by the time of the CASE assay Treatment does not activate target protein By Western analysis using a phospho protein specific antibody verify that your treatment conditions are actually activating the target protein Use a well established treatment known to induce the specific protein phosphorylation event as your positive control Insuffi
19. ly and artificially inflate your OD readings To avoid the appearance of air bubbles remove a sufficient volume of every solution from the washing buffer reservoir avoid pipetting air bubbles and examine the plate before placing into your ELISA plate reader Carefully break any air bubbles with a pipet tip 5 Read absorbance at 595 nm on an ELISA Plate Reader If the signals are greater than the linear range of the instrument remove 50 ul of the 1 SDS solution from every well and add 50 ul of dH20 to each well Repeat the reading of the absorbance at 595 nm on the ELISA Plate Reader 6 Normalize the antibody reading to the relative cell number Divide the OD4so readings for each well by its ODse5 reading 7 To determine the relative extent of target protein phosphorylation normalize the phospho protein specific antibody OD450 ODs95 ratio to the pan protein specific antibody OD450 ODsgs ratio for the same experimental condition Technical Support support SABiosciences com www SABiosciences com 16 Version 2 7 V Troubleshooting Guide A No or weak signal in wells incubated with either the phospho protein specific or the pan protein specific primary antibody 1 2 4 Improper Plate Reader settings Verify the wavelength and filter settings of the ELISA Plate Reader Cold Developing Solution Warm the Developing Solution to room temperature before use Insufficient numbers of cells remain on the plate Check cel
20. rm a Western blot or the need to use r P ATP for in vitro kinase assays The entire assay occurs directly in cell culture wells without sacrificing specificity reproducibility or sensitivity With its 96 well plate format the CASE assay requires very small amounts of cells and treatment reagents and the assay procedure is compatible with high throughput studies These features make the CASE kits especially suitable for screening compounds that activate or inhibit important signaling pathways In the CASE assay cells are seeded into 96 well plates After your experimental treatment the cells are fixed to preserve any activation specific protein modification such as phosphorylation Two primary antibodies are included in the kit One antibody recognizes only the activated phosphorylated form of the specific target protein while another recognizes the specific target protein regardless of its activation state Following incubation with primary and secondary antibodies the amount of bound antibody in each well is determined using a developing solution and an ELISA Plate Reader The absorbance readings are then normalized to relative cell number as determined by a cell staining solution The amount of phosphorylated protein once normalized to the amount of total protein is then directly related to the extent of downstream pathway activation Features and Advantages of the CASE Kits Quantitative Cell based ELISA determines le
21. s turn a medium to dark blue 2 Improper blocking and washing Be sure that washing quenching and blocking steps were all performed according to the recommendations in the protocol Remember to add the solutions carefully down the sides of the wells and to remove liquids by inverting plates over a sink and then tapping the plate gently on a paper towel 3 Secondary antibody concentration is too high Decrease the secondary antibody concentration to half or reduce the secondary antibody incubation time from 1 hour to 30 minutes F High absorbance in blank wells Stop Solution was contaminated with Developing Solution Be sure to use a new and clean Buffer Reservoir for Stop Solution Do not use a Buffer Reservoir that has been previously used to contain Developing Solution to hold Stop Solution G Significant signal variation among replicate wells 1 Cell loss during incubation and washing Be sure to normalize antibody signals with the cell staining reading Asgs A well with an Asgs reading close to the reading of a blank well lacking cells indicates a complete loss of cells from that well Omit this well from your data set Technical Support support SABiosciences com www SABiosciences com 18 Version 2 7 2 Large air bubbles in the 96 well plate can significantly and artificially inflate your OD readings especially when using the 1 SDS solution To avoid the appearance of air bubbles remove a sufficient volume of every
22. spho Protein Specific Primary Antibody Technical Support 888 503 3187 US 301 682 9200 9 CASE Cellular Activation of Signaling ELISA B Cell Culture and Cell Preparation NOTE A fresh and healthily growing cell culture is crucial for a successful CASE experiment Only use cells growing in log phase to set up a CASE experiment If the cell culture is already too old that is if the cells are over confluent if the culture medium turns yellow in color or if adherent cells have started floating to a significant extent split the cells once into a fresh tissue culture flask or dish and fresh medium Allow the cells to grow into log phase once more before seeding into a 96 well plate to set up the CASE experiment See page 7 for recommendations on selecting tissue culture plates 1 Plan your experiment and your cell culture carefully For example see Figure 2 LY294002 s LY294002 ng ml IGF 1 0 1 10 100 10 ng ml IGF 1 CX XN O13 r _ SS 5 Anti Phospho Protein 10 1015 Specific Antibody g 30 30 3 Ss 60 60 z 60 60 J Anti Pan Protein 30 30 3 Specific Antibody Z 10 1013 Flo o l Figure 2 Example of how to plate cells for use with the CASE Kit for AKT S473 Cat No FE 001 Seed cells and plan treatment in two identical sets of cell culture wells In the example here a 96 well plate is divided into two sets and treatments are identical in both sets in a symmetrical fashion Dupli
23. vel of total and activated form of protein at same time Simple Easy quantitative and non radioactive protocol with minimal hands on time ao ee No Extractions Directly measure protein phosphorylation state on cells fixed in a 96 well culture plate Technical Support support SABiosciences com www SABiosciences com 4 Version 2 7 CASE Kit Quick Reference Procedure Assay time lt 3 hours of hands on time Culture Seeding Experimental Treatment Incubation with Primary Antibodies Incubation with HRP conjugated Secondary Antibodies Colorimetric Detection Technical Support Assay for Target Total Protein Assay for Target Phospho Protein All experimental steps take place in a single 96 well cell culture plate 0 5 hours minutes minutes Antibody Specific to Target Total Protein Antibody Specific to Target Phosphorylated Protein SD ED 7 1 Active or Inactive Simply compare relative amounts of target phosphory lated protein to target total protein among your samples to identify the effects of your experimental treatment 1 5 hours minutes Figure 1 Overview of Cellular Activation of Signaling ELISA CASE Kit Procedure 888 503 3187 US 301 682 9200 5 CASE Cellular Activation of Signaling ELISA ll Materials Provided This kit includes enough of the following reagents for 96 assays Box 1 Box 2 Assay amp Detection Reagents Primary
Download Pdf Manuals
Related Search