Home

User Manual

1. and any 10 digit numbers of leading digits 1617 Example 2 1900x lt 1617 gt xxxxxxx Block any number of leading digits 1900 and add prefix 1617 for any dialed 7 digit numbers Example 3 1xxx 2 9 xxxxxx lt 2 011 gt x Allow any length of number with leading digit 2 and 10 digit numbers of leading digit 1 and leading exchange number between 2 and 9 if leading digit is 2 replace leading digit 2 with 011 before dialing 3 Default Outgoing x Example of a simple dial plan used in a Home Office in the US 1900x lt 1617 gt 2 9po000 1 2 9 xx 2 9 xxxxxx 011 2 9 x 3469 11 Explanation of example rule reading from left to right 1900x prevents dialing any number started with 1900 lt 161 7 gt 2 9 xxxxxx allows dialing to local area code 617 numbers by dialing 7 numbers and 1617 area code will be added automatically 1 2 9 xx 2 9 xxxxxx allows dialing to any US Canada Number with 11 digits length 1 2 a b xx at least 2 digits number C d e f Unicorn 600x User Manual Page 31 of 37 Firmware 1 0 0 29 Last Updated 8 2010 Subscribe for MWI Send Anonymous Anonymous Call Rejection Check SIP User ID for incoming INVITE Session Expiration Min SE Caller Request Timer Callee Request Timer Force Timer UAC Specify Refresher Hanlong Technology Co Ltd TECHNOLOGY 011 2 9 x allows international calls starting with 011 3469 11 allow dialing special and emergency numb
2. periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open If choosing STUN and a STUN server is also specified then the Unicorn 600x will behave according to the STUN client specification Under this mode the embedded STUN client inside the Unicorn 600x will attempt to detect if and what type of firewall NAT it is sitting behind through communication with the specified STUN server If the detected NAT is a Full Cone Restricted Cone ora Port Restricted Cone the Unicorn 600x will attempt to use its mapped public IP address and port in all its SIP and SDP messages If choosing STUN with no specified STUN server the Unicorn 600x will periodically every 20 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open If choosing UPNP the embedded UPNP client inside the Unicorn 600x User Manual Page 27 of 37 Firmware 1 0 0 29 Last Updated 8 2010 Use DNS SRV User ID is Phone Number SIP Registration Unregister on Reboot Register Expiration Outgoing call without Registration Local SIP port Local RTP port Use Random Port Refer To Use Target Contact DTMF Payload Type DTMF in Audio Hanlong Technology Co Ltd TECHNOLOGY Unicorn 600x will attempt to mapping ports with the router by upnp protocol Default is No If set to Yes the client will use DNS SRV for server lo
3. Active will be used for all members of the same Hunting group Needless to say those members of the same Hunting group may not be sequential ports In following example ports 3 5 and 7 tied to SIP Account configured in Port 1 marked as Active and ports 4 6 8 tied to SIP Account configured in Port 2 marked as Active as well Example of not sequential configuration of a multiple hunt group FXS Port 1 FXS Port 2 FXS Port 3 FXS Port 4 FXS Port 5 FXS Port 6 FXS Port 7 FXS Port 8 SIP UserlD and Authenticate ID entered Hunting group set to Active SIP UserlD and Authenticate ID entered Hunting Group set to Active SIP UserlD and Authenticate ID left blank Hunting Group set to 1 SIP UserlD and Authenticate ID left blank Hunting group set to 2 SIP UserlD and Authenticate ID left blank Hunting Group set to 1 SIP UserlD and Authenticate ID left blank Hunting Group set to 2 SIP UserlD and Authenticate ID left blank Hunting group set to 1 SIP UserlD and Authenticate ID left blank Hunting Group set to 2 Note A single call directed to the SIP account will NOT result in all ports ringing at the same time They will ring in the hunting group only This feature is applicable to incoming calls only Hanlong Technology Co Ltd Unicorn 600x User Manual Firmware 1 0 0 29 Page 16 of 37 Last Updated 8 2010 TECHNOLOGY 5 8 Inter port Calling In some cases a user may want to make phone cal
4. GUIDE Lurer nenen eenn 19 7 1 Configuring Unicorn 600x Via Voice Hrompt 19 7 2 Configuring Unicorn 600x With Web Browser 20 7 2 1 Access The Web Configuration Menu rrarrnnnnnnanrrnnrnnernranenanennnnnnnnnr 20 7 3 important 5 ns EE 21 7 3 1 NAT 0 EE EN 22 7 3 2 DTMF Methods 1 reolen earn DERE REE ydende aner 22 7 3 3 Preferred VOCODER CGodec sese 22 7 4 End WS SFC NNN ER Hanlong Technology Co Ltd Unicorn 600x User Manual Page 2 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 7 4 1 Status Page Definitions se 23 7 4 2 Basic Settings Page Definitions 00nnann0nnennnnnnennennnnnnnnenrnnrrnnrnnenne 24 7 9 Super User Configuration sse eee ee eee 25 7 5 1 Super Configuration Page Uetntons e ee ee eee eee e e eee 25 75 2 Profile Page Definitions svanen eden 27 7 9 3 FXS Ports Configuration Definitions sse eee ee e eee e ee e eee 34 7 6 Saving The Configuration Changes eee eee e ee 30 7 7 Screen Shot Of Save Configuration Page e eee e eee e 35 7 8 Rebooting From Remote EE 35 7 9 Screen Shot Of Rebooting Page e eee ee 36 6 SOFTWARE UPGRADE wrsicscsssisstesicerecevelcicnaencwcdeasedessvsucdeneas vast sianedvibasnertivabadesseatscn 36 9 RESTORE FACTORY DEFAULT SETTINGS eanennnnernnnnnnnnnennnnennnnnnnnnennnnnnnnnennnnnenn 37 10 TECHNICAL SUPPORT CONTACT rnnnernnnnnnnnevnnnnnnnnnnnnnnnnnnnennnnennnnennnnennnnennnnennnnen 37 Hanlong Technology Co Ltd Unicorn 600x User Manual Page 3 of 3
5. TECHNOLOGY 4 1 Software Features Overview e 4 or 8 FXS ports 6 Two RJ 45 ports switched or routed e Multiple SIP accounts amp profiles 4 or 8 accounts choice of 2 profiles per account Supports Voice Codecs G711 a u Annex I amp Il G723 1A G726 ADPCM with 16 24 32 40 bit rates G729 A B E fax pass through and T 38 Fax Comprehensive Dial Plan support for Outgoing calls G 168 Echo Cancellation Voice Activation Detection VAD Comfort Noise Generation CNG and Packet Loss Concealment PLC e Supports PSTN PBX analog telephone sets or analog trunks TABLE 3 Unicorn 600x SOFTWARE FEATURES Unicorn 600x FXS Analog Gateway Series Unicorn 6004 4 ports 4 SIP accounts amp choice of 2 profiles Telephone Interfaces Unicorn 6008 8 ports 8 SIP accounts amp choice of 2 profiles e FXS RJA Network Interface Two 2 10M 100 Mbps RJ 45 LED Indicators Power and Line LEDs P it i st ie E Voice Activity Detection VAD with CNG comfort noise generation and PLC packet loss concealment AEC Voice over Packet with NLP Packetized Voice Protocol Unit supports Capabilities RTP RTCP and AAL2 protocol 6 168 compliant Echo Cancellation Dynamic Jitter Buffer Modem detection amp auto switch to G 711 PSTNFail over PSTN failover porn on power EE mu EE G711 Annex I PLC Annex II VAD CNG format encoder and decoder G 723 1A G 726 ADPCM with 16 24 32 40 bit
6. in the STUN Server scenario 1 STUN Server under Super Settings webpage Enter a STUN Server IP or FQDN that you may have or look up a free public STUN Server on the internet and enter it on this field If using Public IP keep this field blank 2 Use Random Ports under Super Settings webpage It really depends on your network settings so set this parameter to Yes or No whichever works Generally if you have multiple IP devices under the same network it should be set to Yes If using a Public IP address set this parameter to No 3 NAT Traversal under the Profile web pages Set this to Yes when gateway is behind firewall on a private network 7 3 2 DTMF Methods DTMF Settings are In Profile pages DTMF in audio e DTMF via RTP RFC2833 e DTMF via SIP INFO Enable one or more DTMF methods based on your PBX system 7 3 3 Preferred VOCODER Codec The Unicorn 600x supports a broad range of voice codecs Under Profile web pages choose your preferred order of different codecs e PCMU A or G711u a e 6729 A B E e 723 e G726 32k 7 4 End User Configuration This section will describe the options in the Web configuration user interface As mentioned a user can log in as an administrator or end user Hanlong Technology Co Ltd Unicorn 600x User Manual Page 22 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY Functions available for the end user are STATUS Displays the network status accoun
7. selected and no Caller ID is configured the selected ring tone will be used for all incoming calls Conference mode default option is No If set to yes the feature code for coference 23 would be disabled Unicorn 600x User Manual Firmware 1 0 0 29 Page 30 of 37 Last Updated 8 2010 Disable Call Waiting Disable Call Waiting Tone Ring Timeout No Key Entry Timeout Use as Send Key Dial Plan Hanlong Technology Co Ltd TECHNOLOGY Default is NO User can use star codes to enable disable call waiting Default is NO This is to disable the stutter call waiting tone when a call waiting call arrived An incoming call will stop ringing when not picked up given a specific period of time Default is 4 seconds T This parameter allows users to configure the key to be used as the Send or Dial key If set to Yes pressing this key will immediately trigger the sending of dialed string collected so far In this case this key is essentially equivalent to the Re Dial key If set to No this key will then be included as part of the dial string to be sent out Dial Plan Rules Accept Digits 1 2 3 4 5 6 7 8 9 0 A a B b C c D d Grammar x any digit from 0 9 XX at least 2 digits number exclude 3 5 any digit of 3 4 or 5 147 any digit 1 4 or 7 lt 2 011 gt replace digit 2 with 011 when dialing Example 1 369 11 1617xxxxxxx Allow 311 611 911
8. this field is set to be 2 and if the first vocoder chosen is G729 or G711 or G726 then the ptime value in the SDP message of an INVITE request will be 20ms If the configured voice frames per TX exceeds the maximum allowed value the Unicorn 600x will use and save the maximum allowed value for the corresponding first vocoder choice The maximum value for PCM is 10 x10ms frames for G726 it is 20 x10ms frames for G723 it is 32 x30ms frames for G729 G728 64 x10ms and 64 x2 5ms frames respectively This defines the encoding rate for G723 vocoder By default 6 3kbps rate is chosen Default is No VAD allows detecting the absence of audio and conserve bandwidth by preventing the transmission of silent packets over the network Default is No When set to Yes the device will change the destination to send RTP packets to the source IP address and port of the inbound RTP packet last received by the device Default is T 30 Fax Pass Through or T 38 Auto Detect FolP Default is Callee This decides whether Caller or Callee sends out the re INVITE for T 38 or Fax Pass Through Select either Fixed or Adaptive based on network conditions Select Low Medium or High based on network conditions Caller ID must be configured Select a Distinctive Ring Tone 1 through 3 for a particular Caller ID The device will ONLY use selected ring tones for particular Caller IDs For all other calls the device will use System Ring Tone When
9. will use session timer when it receives inbound calls with session timer request Default is NO If selecting Yes the device will use session timer even if the remote party does not support this feature Selecting No will allow the device to enable session timer only when the remote party support this feature To turn off Session Timer select No for Caller Request Timer Callee Request Timer and Force Timer Default is NO As a Caller select UAC to use the device as the refresher or UAS to use the Callee or proxy server as the refresher Unicorn 600x User Manual Page 32 of 37 Firmware 1 0 0 29 Last Updated 8 2010 UAS Specify Refresher Force INVITE Special Feature FXS Impedance Caller ID Scheme Onhook Voltage Polarity Reversal Hook Flash Timing Volume Amplification Ring Tones Hanlong Technology Co Ltd TECHNOLOGY Default is Omit As a Callee select UAC to use caller or proxy server as the refresher or UAS to use the device as the refresher Default is UAC Session Timer can be refreshed using INVITE method or UPDATE method Select Yes to use INVITE method to refresh the session timer Default is NO Choose the selection to meet some special requirements from Soft Switch vendors Default is standard Select the impedance of anolog telephone connected to phone port select caller ID to suit standard of different area Select onhook voltage to suit standard of differe
10. with an Ethernet cable to your PC ae WAN Connect to the internal LAN network or router PSTN Line pot eee EG eser Factory Reset button Press for 8 seconds to reset factory default settings ss DC9V2A gt Power adapter connection XS port to be connected to analog phones fax gt FXS1 FXS8 machines Note Unicorn6004 has the ports from FXS1 FXS4 Once the Unicorn is turned on and configured the front display panel indicates the status of the unit 2 4 Diagram Of Unicorn 600x Display Panel Display LEDs FXS port status TABLE 2 Definitions Of The Unicorn Display Panel Hanlong Technology Co Ltd Unicorn 600x User Manual Page 6 of 37 Firmware 1 0 0 29 Last Updated 8 2010 Indicates Power Remains ON when Power is connected Power LED andtumed ON am RUNLED blinking after boot up gt LANLED indicates LAN port activity i vom emm Indicate status of the respective FXS Ports on the back panel LEDs 1 8 Busy ON Solid Green Available OFF EG _ Slow blinking FXS LEDs indicates Voice Mail for that port NOTE Flast blinking of RUN WAN LED together indicates a firmware upgrade or provisioning state LEDs POWER and WAN are ON and READY blinking when device is up and running and successfully registered to the SIP Server 3 APPLICATION DESCRIPTION There are two scenarios where the Unicorn 600x series can be effectively used to enable any business to l
11. 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 7 4 2 Basic Settings Page Definitions Setting options Web Port IP Address Time Zone Allow DHCP Option 2 to override Time Zone setting Daylight Savings Time Device Mode LAN Subnet Mask LAN DHCP Base IP DHCP IP Lease Time Port Map End User Password Reply to ICMP on WAN Hanlong Technology Co Ltd BASIC OPTIONS SETTING Definitions Default is 80 There are 3 modes under which the Unicorn 600x can operate If DHCP mode is enabled then all the field values for the Static IP mode are not used even though they are still saved in the chipset s memory The Unicorn 600x will acquire its IP address from the first DHCP server it discovers from the office nome network it is connected to To use the PPPoE feature the PPPoE account settings need to be set The Unicorn 600x will attempt to establish a PPPoE session if any of the PPPoE fields have been entered with data If Static IP mode is enabled then the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields will need to be configured by the user These fields are reset to zero by default This parameter controls how the displayed date time will be adjusted according to the specified time zone If set yes and under DHCP mode the device will try to get option 2 from DHCP configure and overwrite Time Zone This parameter controls whether the di
12. 4 The default value for FXS 2 port is 5008 This parameter when set to Yes will force random generation of both the local SIP and RTP ports This is usually necessary when multiple Unicorn 600x are behind the same NAT Default is NO If set to VES then for Attended Transfer the Refer To header uses the transferred target s Contact header information This parameter sets the payload type for DTMF using RFC2833 This parameter specifies the mechanism to transmit DTMF digit in audio which means DTMF is combined in audio Unicorn 600x User Manual Page 28 of 37 Firmware 1 0 0 29 Last Updated 8 2010 DTMF via RFC2833 DTMF via SIP INFO Send Flash Event Enable Call Features Proxy Require USE NAT IP Disable call waiting No Key Entry Timeout Preferred Vocoder Voice Frames per TX Hanlong Technology Co Ltd TECHNOLOGY signal not very reliable with low bit rate codec Default is YES This parameter specifies the mechanism to transmit DTMF digit via RTP RFC2833 Default YES This parameter specifies the mechanism to transmit DTMF digit via SIP INFO Default is NO This parameter allows users to control whether to send an SIP NOTIFY message indicating the Flash event or just to switch to the voice channel when users press the Flash key Default is No If set to Yes Call Forwarding AS Do Not Disturb are supported locally SIP Extension to notify SIP server that the unit is behind the NAT Firewall
13. 5 2 1 Phone or Extension Numbers 1 Dial the number directly and wait for 4 seconds Default No Key Entry Timeout or 2 Dial the number directly and press Use as dial key must be configured in web configuration Hanlong Technology Co Ltd Unicorn 600x User Manual Page 12 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY Examples 1 Dial an extension directly on the same proxy and then press the or wait for 4 seconds 2 Dial an outside number first enter the prefix number usually 1 or international code followed by the phone number Press or wait for 4 seconds Check with your VoIP service provider for further details on prefix numbers 5 2 2 Direct IP Calls Direct IP calling allows two parties that is a FXS Port with an analog phone and another VoIP Device to talk to each other in an ad hoc fashion without a SIP proxy Elements necessary to completing a Direct IP Call 1 Both Unicorn600x and other VoIP Device have public IP addresses or 2 Both Unicorn600x and other VoIP Device are on the same LAN using private IP addresses or 3 Both Unicorn600x and other VoIP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ Unicorn600x supports two ways to make Direct IP Calling Using IVR 1 Pick up the analog phone then access the voice menu prompt by dial 2 Dial 47 to access the direct IP call menu 3 Enter the IP ad
14. 7 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 1 WELCOME Thank you for purchasing the Hanlong Unicorn 600x Analog FXS IP Gateway The Unicorn 600x offers an easy to manage easy to configure IP communications solution for any business with virtual and or branch locations The Unicorn 600x supports popular voice codecs and is designed for full SIP compatibility and interoperability with 3rd party SIP providers thus enabling you to fully leverage the benefits of VoIP technology integrate a traditional phone system into a VoIP network and efficiently manage communication costs This manual will help you learn how to operate and manage your Unicorn FXS Analog IP Gateway and make the best use of its many upgraded features including simple and quick installation multi party conferencing This IP Analog Gateway is very easy to manage and scalable specifically designed to be an easy to use and affordable VoIP solution for the small medium business or enterprise 1 1 Gateway Unicorn 600x Overview The new Unicorn 600x series has a compact and quiet design no fans and offers superb audio quality rich feature functionality strong security protection and good manageability It is auto configurable remotely manageable and scalable The Unicorn 600x features 4 or 8 port FXS interface for analog telephones dual 10M 100Mbps network ports with integrated router PSTN life line in case of power failure In addition it supports the opti
15. NAT IP address used in SIP SDP message Default is blank Default is No Default is No The Unicorn600x supports up to 5 different Vocoder types including G 711 A U law G 726 Supports bit rates 32K G 723 1 G 729A B The user can configure Vocoders in a preference list that will be included with the same preference order in SDP message The first Vocoder is entered by choosing the appropriate option in Choice 1 The last Vocoder is entered by choosing the appropriate option in Choice 6 This field contains the number of voice frames to be transmitted in a single packet When setting this value the user should be aware of the requested packet time used in SDP message as a result of configuring this parameter This parameter is associated with the first vocoder in the above vocoder Preference List or the actual used payload type negotiated between the 2 conversation parties at run time e g if the first vocoder is configured as G723 and the Unicorn 600x User Manual Page 29 of 37 Firmware 1 0 0 29 Last Updated 8 2010 G723 Rate VAD Symmetric RTP FAX Mode Fax Tone Detection Mode Jitter Buffer Type Jitter Buffer Length Distinct Ring Tone Use Bell style 3 way Conference Hanlong Technology Co Ltd TECHNOLOGY Voice Frames per TX is set to be 2 then the ptime value in the SDP message of an INVITE request will be 60ms because each G 23 voice frame contains 30ms of audio Similarly if
16. SETTING Meaning FXS Port Number User account information provided by VoIP service provider ITSP Usually in the form of digit similar to phone number or actually a phone number SIP service subscriber s Authenticate ID used for authentication Can be identical to or different from SIP User ID SIP service subscriber s account password for Unicorn 600x to register to SIP servers of ITSP Name Select the corresponding Profile ID 1 2 This feature enables the gateway to register all existing FXS ports with the same phone number Each incoming call will be routed to first available port in round robin mode User may configure all ports as members of the same Hunt Group or it may configure different port combinations for more than one Hunt Group For example Ports 1 3 and 5 may be members of the same hunt group the rest of the ports may have separate numbers and may be reached independently Select appropriate value for Hunting Group feature The original SIP account should be set to Active while the group members should be set to the port number of the Active Port Example configuration of a multiple hunt group FXS Port 1 SIP UserlD and Authenticate ID entered Hunting group set to Active FXS Port 2 SIP UserlD and Authenticate ID left blank Hunting Group set to 1 FXS Port 3 SIP UserlD and Authenticate ID left blank Hunting Group set to 1 FXS Port 4 SIP UserlD and Authenticate ID entered Hunting grou
17. User Manual Unicorn 600X Analog IP Gateway 4 or 8 FXS Ports Hanlong Technology Co Ltd http www hanlongtek com TECHNOLOGY 1 WEECOME E 4 1 1 Gateway Unicorn 600x Ovenvlew see eee e eee e e 4 1 2 Safety E elle E ale 4 1 3 ENEE ee 5 2 CONFIGURE YOUR UNICORN 600X rennnnevnnnennnnennnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnennnnnnnnnennne 5 2 1 EU PN D 2 2 Connect The Unicorn 600X eee eee 5 2 3 Diagram of Unicorn 600x Back Panel 6 2 4 Diagram Of Unicorn 600x Display Panel see eee 6 3 APPLICATION DESCRIPTION nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnennnnennnnennnnennn 7 3 1 Examples Of Unicorn 600x Configurations ese ee e eee e ee eee 7 3 1 1 Application One Unicorn 600x FXS Gateway Configuration PBX SCENT Ee TE 7 3 1 2 Application Two Unicorn 600x amp Unicorn 60x0 Scenario Toll Free Calling Between Locatons eee ee 8 4 UNICORN 600X FEATURES annnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnennnnennnnennnnennnnennnnennnnennnnnn 8 4 1 Software Features Overview eee ee e eee 9 4 2 leeden 10 5 iBASIC el Mt LN 11 5 1 Understanding Unicorn Voice Prompts sese ese eee ee eee ee e 11 5 2 Teilen el e E 12 5 2 1 Phone or Extension Numbers A 12 5 2 2 Direct Te 13 5 3 EAN 13 9 4 Ja NAG T 14 5 5 TANN 14 5 6 3 Way Conferencing E 15 5 f Ula ao e T 15 5 8 mterporr C aling E 17 5 9 PSTN Pass Through Life lu 17 5 10 Sending ANd RECEIVING Fax 17 b ei TE NEE 17 7 CONFIGURATION
18. at the bottom of the configuration menu The user can re login to the unit after waiting for about 30 seconds Hanlong Technology Co Ltd Unicorn 600x User Manual Page 35 of 37 Firmware 1 0 0 29 Last Updated 8 2010 HAN LONG TECHNOLOGY 7 9 Screen Shot Of Rebooting Page Hanlong VOIP Device Configuration All Rights Reserved Hari ong Technology CO LTD 2005 2008 8 SOFTWARE UPGRADE To upgrade software Unicorn 600x can be configured with a TFTP server where the new code image is located The TF TP upgrade can work in either static IP or DHCP mode using private or public IP address It is recommended to set the TF TP server address in either a public IP address or on the same LAN with the Unicorn 600x There are two ways to set up the TFTP server to upgrade the firmware namely through voice menu prompt or via the Unicorn 600x s Web configuration interface To configure the TFTP server via voice prompt follow section 5 1 with option 06 once set up the TFTP IP address power cycle the ATA the firmware will be fetched once the ATA boots up To configure the TFTP server via the Web configuration interface open up your browser to point at the IP address of the Unicorn 600x Input the admin password to enter the configuration screen From there enter the TF TP server address in the designated field towards the bottom of the configuration screen Once the TFTP server is configured please power cycle the Unicorn 600x TFTP
19. ditional telephony features available in a PBX as well as additional advanced telephony features TABLE 6 Call Features Table Star Code Call Features 730 Block CallerID for all config change EE EET UTE ele Hanlong Technology Co Ltd Unicorn 600x User Manual Page 17 of 37 Firmware 1 0 0 29 Last Updated 8 2010 BT Oi Block CallerID per call EE Send Caller per call een i Direct IP Calling Dial 47 IP address No dial tone will be 47 played in the middle W KEE Detail see Direct IP Calling section on page 12 790 Disable Call Waiting for all config change Di Enable Call Waiting for all config change Call Return Service Dial 69 and the phone will dial the last incoming phone number received e H Disable Call Waiting Per Call msmmmeemeremesemenese KA Enable Call Waiting Per Call mm Unconditional Call Forward Dial 72 and then the forwarding 72 number followed by Wait for dial tone and hang up dial tone indicates successful forward EEE nn nen ne ee et te et et et en ee te ee ee eet Cancel Unconditional Call Forward Dial 73 and wait for dial 7 IT BEES 74 Enable Paging Call Dial 74 and then the destination phone va umber you want to activate in Paging mode 78 Enable Do Not Disturb DND When enabled all incoming calls will be rejected pr Dr eee i 79 Disable Do Not Disturb DND When disabled
20. dress of the configuration server UPGRADE PROTOCOL Select voice menu option 15 to choose firmware and configuration upgrade protocol User can choose between TFTP and HTTP FIRMWARE UPGRADE MODE Select voice menu option 17 to choose firmware upgrade mode among the following three options 1 always check 2 check when pre suffix changes and 3 never upgrade WAN PORT WEB ACCESS Select voice menu option 12 to enable WAN Port Wed Access of the device configuration pages Hanlong Technology Co Ltd Unicorn 600x User Manual Page 19 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 7 2 Configuring Unicorn 600x With Web Browser Unicorn 600x has an embedded Web server that will respond to HTTP GET POST requests It also has embedded HTML pages that allow users to configure the Unicorn 600x through a Web browser such as Microsoft s IE and AOL s Netscape The GUI interface can be download at bellow http www hanlongtek com books 6008 qui rar This gui include bellow pages SCREENSHOT OF DEVICE STATUS PAGE SCREENSHOT OF BASIC OPTIONS PAGE SCREENSHOT OF SUPPER OPTIONS PAGE SCREENSHOT OF PROFILE 1 PAGE SCREENSHOT OF PROFILE 2 PAGE SCREENSHOT OF FXS PORTS PAGE oS dE S 7 2 1 Access The Web Configuration Menu The Unicorn 600x HTML configuration menu can be accessed via LAN or WAN port From the LAN port 1 Directly connect a computer to the LAN port 2 Open a command window on the computer 3 Type in ipco
21. dress using format ex 192 168 0 160 after the dial tone Using Star Code 1 Pick up the analog phone then dial 47 2 Enter the target IP address using same format as above Note NO dial tone will be played between step 1 and 2 Destination ports can be specified by using encoding for followed by the port number Examples a If the target IP address is 192 168 0 160 the dialing convention is 47 or Voice Prompt with option 47 then 192 168 0 160 followed by pressing the key if it is configured as a send key or wait 4 seconds In this case the default destination port 5060 is used if no port is specified b If the target IP address port is 192 168 1 20 5062 then the dialing convention would be 47 or Voice Prompt with option 47 then 192 168 0 160 5062 followed by pressing the F key if it is configured as a send key or wait for 4 seconds NOTE When completing direct IP call the Use Random Port should set to NO You can not make direct IP calls between FXS1 to FXS2 since they are using same IP 5 3 Call Hold Place a call on hold by pressing the flash button on the analog phone if the phone has Hanlong Technology Co Ltd Unicorn 600x User Manual Page 13 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY that button Press the flash button again to release the previously held Caller and resume conversation If no flash button is available use hook flas
22. ers 311 411 611 and 911 Note In some cases user wishes to dial strings such as 123 to activate voice mail or other application provided by service provider In this case should be predefined inside dial plan feature and the Dial Plan should be I x More information can be availabled at Dail Plan Notes Default is No When set to Yes a SUBSCRIBE for Message Waiting Indication will be sent periodically If this parameter is set to Yes the From header in outgoing INVITE message will be set to anonymous essentially blocking the Caller ID from displaying Default is No If set to Yes incoming calls with anonymous Caller ID will be rejected with 486 Busy message Check the SIP User ID in Request URI If they don t match the call will be rejected The session timer extension enables SIP sessions to be periodically refreshed via a re INVITE request Once the session interval expires if there is no refresh via a re INVITE message the session will be terminated Session Expiration is the time in seconds at which the session is considered timed out if no successful session refresh transaction occurs beforehand The default value is 180 seconds Default is 180 seconds The minimum session expiration in seconds Default is 90 seconds If selecting Yes the device will use session timer when it makes outbound calls if remote party supports session timer Default is NO If selecting Yes the phone
23. everage the benefits of VoIP and the Internet 3 1 Examples Of Unicorn 600x Configurations 3 1 1 Application One Unicorn 600x FXS Gateway Configuration PBX Scenario VoIP Anywhere in the world FXS Trunks Analog _ Phones Ka 4 or 8 Ports INTERNET C CLOUD Unicorn FXS Series Hanlong Technology Co Ltd Unicorn 600x User Manual Page 7 of 37 Firmware 1 0 0 29 Last Updated 8 2010 wr Pan HANLONG C3 E TECHNOLOG 3 1 2 Application Two Unicorn 600x amp Unicorn 60x0 Scenario Toll Free Calling Between Locations ITISP ia 66666666 6 ITISPI L R T E T T eet KT p e re SS Sy ke mm vm mm vm rm mm mm mm rem d ip micorn 2001 Unicorn Internet x Branch E 4 UNICORN 600X FEATURES The Unicorn 600x is a next generation IP voice gateway that is interoperable and compatible with leading IP PBXs SoftSwitches and SIP platforms The Unicorn 600x FXS series is auto configurable remotely manageable and scalable There are two FXS models the Unicorn 6004 and Unicorn 6008 each offering superb voice quality traditional telephony functionality easy deployment and 4 or 8 FXS ports respectively Each model features flexible dialing plans PSTN failover integrated call routing to support a pure IP network call and an external power supply Hanlong Technology Co Ltd Unicorn 600x User Manual Page 8 of 37 Firmware 1 0 0 29 Last Updated 8 2010 KS HAN LON CG
24. factory settings following these four 4 steps 1 Unplug the Ethernet cable 2 Locate a needle sized hole on the back panel of the gateway unit next to the power connection 3 Insert a pin in this hole and press for about 8 seconds 4 Take out the pin All unit settings are restored to factory settings IVR Command Reset default factory settings using the IVR Prompt Table 5 1 Dial for voice prompt 2 Enter 99 and wait for reset voice prompt 3 Enter 862584658050 NOTE 1 Factory Reset will be disabled if the Lock keypad update is set to Yes 2 Please be aware by default the Unicorn 600x WAN side HTTP access is disabled After a factory reset the device s web configuration page can be accessed only from its LAN port 10 TECHNICAL SUPPORT CONTACT Email Support mail hanlongtek com Hanlong Technology Co Ltd Unicorn 600x User Manual Page 37 of 37 Firmware 1 0 0 29 Last Updated 8 2010
25. h toggle on off hook quickly You may drop a call using hook flash 5 4 Call Waiting Call waiting tone 3 short beeps indicates an incoming call if the call waiting feature is enabled Toggle between incoming call and current call by pressing the flash button First call is placed on hold Press the flash button to toggle between two active calls 5 5 Call Transfer Blind Transfer Assume that call Caller A and B are in conversation A wants to Blind Transfer B to C 3 Caller A presses FLASH on the analog phone to hear the dial tone 4 Caller A dials 87 then dials caller C s number and then or wait for 4 seconds 5 Caller A will hear the confirm tone Then A can hang up NOTE Enable Call Feature must be set to Yes in web configuration page Caller A can place a call on hold and wait for one of three situations 1 A quick confirmation tone similar to call waiting tone followed by a dial tone This indicates the transfer is successful transferee has received a 200 OK from transfer target At this point Caller A can either hang up or make another call 2 A quick busy tone followed by a restored call on supported platforms only This means the transferee has received a 4xx response for the INVITE and we will try to recover the call The busy tone is just to indicate to the transferor that the transfer has failed 3 Continuous busy tone The phone has timed out Note continuous busy tone doe
26. ication Of Unicorn 600x Ports A rB FXS Ports E LAN interface EE 2 x RJ45 10 100Mbps switched or routed PSINPot PSTN fail over port LED do 8LEDs GREEN gt teie Switching Input 100 240V AC 50 60Hz 0 5A Max Power Adaptor Output 9V DC 2A SEENEN UL certified Dimension 22Bmm L x 135mm W x 35mm H _Weight _ 0 29 Ibs 3 5 0z ae e OE E Humidity 100p 90 non condensing E Compliance FCC CE Hanlong Technology Co Ltd Unicorn 600x User Manual Page 10 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 5 BASIC OPERATIONS 5 1 Understanding Unicorn Voice Prompts Unicorn 600x has a stored voice prompt menu for quick browsing and simple configuration To enter the voice prompt menu press on the standard analog phone connected to any FXS port TABLE 5 Definitions Of The Unicorn Voice Prompts Voice Will Say the Following Enter for the next menu option Main i Enter to return to the main menu Enter a Menu Option Menu Enter 01 07 12 17 47 86 or 99 Menu a EE a te option E Enter 9 to toggle the selection If user selects Static IP Mode user need l configure all the IP address information through menu 02 to 05 01 DHCP Mode Static IP Mode If user selects Dynamic IP Mode the l device will retrieve all IP address information from DHCP server automatically when user reboots the dev
27. ice eee SENE ZEN The current WAN IP address kb i 02 IP Address IP address announced Enter 12 digit new IP address FE SE rn Static IP Mode gt l 03 _ Subnet IP address EES _Same as Menu option 02 EE 04 Gateway IP address gt Same as Menu option02 gt Op DNS Server IP address Same as Menu option 02 gt 06 i MAC Address Announces the Mac address of the unit fC Enter 9 to go to the next selection in the list e PCMU 07 Preferred Vocoder 8 PCMA 8 G 726 8 G 723 Ge G 729 sr Enter 9 to toggle between enable and dk WAN Port Web Access sate 13 i S Announces current Firmware Server IP E address Enter 12 digit new IP address Hanlong Technology Co Ltd Unicorn 600x User Manual page lL of 37 Firmware 1 0 0 29 Last Updated 8 2010 NE TTT TTT P Configuration Server IP Announces current Config Server Path IP GE Address mme address Enter 12 digit new IP address Upgrade protocol for firmware and configuration update 15 Upgrade Protocol a Enter 9 to toggle between TFTP and 16 Firmware Version Firmware version information j J 2 e e nr 2 er ee ee g Firmware upgrade mode Enter ER to rotate among the following three options 17 Firmware Upg
28. incoming calls will rd s ed 87 Blind Transfer eee i Busy Call Forward Dial 90 and then the forwarding number on oo _ followed by 4 Wait for dial tone then hang up 97 Cancel Busy Call Forward dial 91 Wait for dial tone Hang up FLETTET PAN E ar mn nie ba E Oa Oe We ETE sem TEES seg ert Ge OS nen vegen Se een age grev ye REE E SS Te pekere Ne H E TE NE SE E Delayed Call Forward Dial 92 and then the forwarding number followed by Wait for dial tone then hang up 93 Cancel Delayed Call Forward mme Dial 793 for a dialtone then hang up hmmm If user hears call waiting beep flash hook will switch to the new Flash Hook incoming call Also used to switch to a new channel for a new call Pressing pound sign will serve as Re Dial key Hanlong Technology Co Ltd Unicorn 600x User Manual Page 18 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 7 CONFIGURATION GUIDE 7 1 Configuring Unicorn 600x Via Voice Prompt DHCP MODE Select voice menu option 01 to enable Unicorn 600x to use DHCP STATIC IP MODE Select voice menu option 01 to enable Unicorn 600x to use STATIC IP mode then use option 02 03 04 05 to set up IP address Subnet Mask Gateway and DNS server respectively FIRMWARE SERVER IP ADDRESS Select voice menu option 13 to configure the IP address of the firmware server CONFIGURATION SERVER IP ADDRESS Select voice menu option 14 to configure the IP ad
29. ls between Unicorn gateway ports when the gateway will be used as stand alone unit without any SIP server This feature will also be applicable when the gateway is used in mode Hunting Groups and will be registered to SIP server only with one master number In such cases users still will be able to make inter port calls by using the IVR feature For example the user connected to port 1 can reach the user connected to port 3 by dialing and 73 Digit 7 indicated using inter port calling feature digit 3 indicates port number which should be reached At the Same manner the user connected to port 4 can reach the user connected to port 8 by dialing and 78 Note The Unicorn 600x support fast mode for inter port calling by using 48x For example PORT 1 call PORT 2 just dail 482 PORT 2 call PORT 1 just need to dail 481 5 9 PSTN Pass Through Life Line The RJ 11 line jack on the Unicorn 600x side functions as a pass through jack when the Unicorn 600x is out of power The pass through life line enables the user to use the analog phone for PSTN calls directly without using an access code 5 10 Sending And Receiving Fax Unicorn 600x supports fax in two modes 1 Fax Pass through If the service provider does not support T 38 pass through mode may be used If you have problems with sending or receiving Fax toggle the Fax Tone Detection Mode setting 2 1 38 Fax over IP 6 CALL FEATURES The Unicorn 600x supports the tra
30. nfig release the IP address etc becomes 0 4 Type in ipconfig renew the computer gets an IP address in 192 168 22 x segment by default 5 Open a web browser type in the default gateway IP address http 192 168 22 1 You will see the login page of the device From the WAN port The WAN port HTML configuration option is disabled by default from factory To access the HTML configuration menu from the WAN port 1 Enable the WAN Port Web Access option via IVR option 12 2 Find the WAN IP address of the Unicorn 600x using voice prompt menu option 02 3 Access the Unicorn 600x Web Configuration page by the following URI via WAN port http Unicorn 600x IP Address the Unicorn 600x IP Address is the WAN IP address for Hanlong Technology Co Ltd Unicorn 600x User Manual Page 20 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY the Unicorn 600x NOTE If using a web browser to enter the configuration page strip the leading Oe because the browser will parse in octet i e if the IP address is 192 168 001 014 please type in 192 168 1 14 Once the HTTP request is entered and sent from a Web browser the user will see a log in screen There are two default passwords for the login page Password Web pages allowed End User Level 1234 Only Status and Basic Settings Administrator Level Browse all pages Only an administrator can access the SUPER SETTINGS configuration page 1 There are
31. nt area or PBX Select Polarity Reversal to adapt some call charge billing system Default is NO Time period when the cradle is pressed Hook Flash to simulate FLASH To prevent unwanted activation of the Flash Hold and automatic phone ring back adjust this time value Voice path volume adjustment Rx is a gain level for signals transmitted by FXS Tx is a gain level for signals received by FXS Default OdB for both parameters Loudest volume 6dB Lowest volume 6dB User can adjust volume of call on either end using the Rx Gain Level parameter and the Tx Gain Level parameter located on the FXS Port Configuration page If call volume is too low when using the FXS port ie the ATA is at user site adjust volume using the Rx Gain Level parameter under the FXS Port Configuration page If voice volume is too low at the other end user may increase the far end volume using the Tx Gain Level parameter under the FXS Port Configuration page This function lets you configure ring tone cadence preferences User has 10 choices The configuration completed in Distinctive Ring Tones block in the same page applies to ring tones cadences configured here Unicorn 600x User Manual Page 33 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 7 5 3 FXS Ports Configuration Definitions Setting Options FXS Port SIP User ID Authenticate ID Password Name Profile ID Hunting Group Hanlong Technology Co Ltd FXS PORT
32. okup If the Unicorn 600x has an assigned PSTN telephone number this field should be set to Yes Otherwise set it to No If Yes is set a user phone parameter will be attached to the From header in SIP request This parameter controls whether the Unicorn 600x needs to send REGISTER messages to the proxy server The default setting is Yes Default is No If set to Yes then the SIP user will be unregistered on reboot This parameter allows the user to specify the time frequency in minutes the Unicorn 600x refreshes its registration with the specified registrar The default interval is 60 minutes or 1 hour The maximum interval is 65535 minutes about 45 days Default is No If set to Yes user can place outgoing calls even when not registered if allowed by ITSP but is unable to receive incoming calls even when not registered if allowed by ITSP but is unable to receive incoming calls This parameter defines the local SIP port the Unicorn 600x will listen and transmit The default value for FXS port 1 is 5060 The default value for FXS 2 port is 5062 This parameter defines the local RTP RTCP port pair the Unicorn 600x will listen and transmit It is the base RTP port for channel 0 When configured channel 0 will use this port value for RTP and the port value 1 for its RTCP channel 1 will use port value 2 for RTP and port value 3 for its RTCP The default value for FXS port 1 is 500
33. on of 2 SIP Server profiles caller ID for various countries regions T 38 fax flexible dialing plans security protection SIPS TLS comprehensive voice codecs including G 711 a u law G 723 1 G 726 32K bit rates G 729A B E Caution Changes or modifications to this product not expressly approved by Hanlong Technology or operation of this product in any way other than as detailed by this User Manual could void your manufacturer warranty Information in this document is subject to change without notice No part of this document may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of Hanlong Technology 1 2 Safety Compliances The Unicorn 600x is compliant with various safety standards including FCC CE Its power adaptor is compliant with UL standard Warning use only the power adapter included in the Unicorn 600x package Using an alternative power adapter may permanently damage the unit Hanlong Technology Co Ltd Unicorn 600x User Manual Page 4 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 1 3 Warranty Hanlong has a reseller agreement with our reseller customer End users should contact the company from whom you purchased the product for replacement repair or refund If you purchased the product directly from Hanlong contact your Hanlong Sales and Service Representative for a RMA Return Materials Authorization number Hanl
34. ong reserves the right to remedy warranty policy without prior notification 2 CONFIGURE YOUR UNICORN 600X Connecting your Unicorn 600x is easy Before you begin please verify the contents of the Unicorn 600x package 2 1 Equipment Packaging Unpack and check all accessories The Unicorn 600x package contains One Unicorn 600x VoIP adapter One universal power supply One Ethernet cable 2 2 Connect The Unicorn 600x Managing the Unicorn 600x gateway and connecting the unit to the VoIP network is very simple Follow these four 4 steps to connect your Unicorn 600x gateway to the Internet and access the unit s configuration pages 1 Connect standard touch tone analog phones to the FXS1 FXS8 ports 2 Insert the Ethernet cable into the WAN port of Unicorn 600x and connect the other end of the Ethernet cable to an uplink port a router or a modem etc 3 Connect a PC to the LAN port of Unicorn 600x for initial configuration or if it is being used as a router 4 Plug the power adapter into the Unicorn 600x and into a power outlet Hanlong Technology Co Ltd Unicorn 600x User Manual Page 5 of 37 Firmware 1 0 0 29 Last Updated 8 2010 w wax co HAN TECHNOLOGY G 2 3 Diagram of Unicorn 600x Back Panel FASI FASZ FXS3 FXS4 FXSS FXSE FKSS P FAST FB LAN WAN DC gv D Pit Te FXS LAN WAN Power PSTN Line Reset Supply Ports TABLE 1 Definitions Of The Unicorn Connectors Connect the LAN port
35. p set to Active FXS Port 5 SIP UserlD and Authenticate ID left blank Hunting Group set to 4 FXS Port 6 SIP UserlD and Authenticate ID left Unicorn 600x User Manual Page 34 of 37 Firmware 1 0 0 29 Last Updated 8 2010 San oOo HAN TECHNOLOGY G blank Hunting Group set to 4 FXS Port 7 SIP UserlD and Authenticate ID entered Hunting group set to Active FXS Port 8 SIP UserlD and Authenticate ID left blank Hunting Group set to 7 Hunt Group 1 contains ports 1 2 3 Hunt Group 4 contains ports 4 5 6 Hunt Group 7 contains ports 7 8 This field default is blank If set a number it is mean Off hook Auto dial that according port will auto outgo the setting number when this port off hook 7 6 Saving The Configuration Changes Once a change is made press the Update button in the Configuration Menu The following screen will confirm that the changes have been saved To activate changes reboot or power cycle the Unicorn 600x after changes are made 7 7 Screen Shot Of Save Configuration Page SAVING Hanlong Your changes have been saved VOIP Device Please wait 5 second and then reboot the device Reboot Configuration All Rights Reserved Hanlong Technology CO LTD 2005 2008 DEVICE STATUS BASIC OPTIONS SUPER OPTIONS PROFILE 1 PROFILE 2 FXS PORTS 7 8 Rebooting From Remote The administrator can remotely reboot the unit by pressing the Reboot button
36. process may take as long as 1 to 2 minutes over the Internet or just 30 seconds if it is performed on a LAN Users are recommended to conduct TFTP upgrade in a controlled LAN environment if possible For those who do not have a local TF TP server Hanlong technology provides a NAT friendly TFTP server on the public Internet for firmware upgrade Please check the Service section of Hanlong s Web site to obtain this TFTP server s IP address NOTES When Hanlong ATA boot up it will send TFTP or HTTP request to download configuration files there are two configuration files one is cfg bin and the other is cfg001fc1xxxxxx where 001fc1xxxxxx is the MAC address of the Unicorn 600x These two files are for initial automatically provisioning purpose only for normal TFTP or HTTP firmware upgrade the following error messages in a TFTP or HTTP server log can be ignored Hanlong Technology Co Ltd Unicorn 600x User Manual Page 36 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 9 RESTORE FACTORY DEFAULT SETTINGS WARNING Restoring the Factory Default Setting will DELETE all configuration information of the phone Please BACKUP or PRINT out all the settings before you approach to following steps Hanlong will not take any responsibility if you lose all the parameters of setting and cannot connect to your VoIP service provider FACTORY RESET There are two 2 methods for resetting your unit Reset Button Reset default
37. rade 1 always check 4 check when pre suffix changes Enter the target IP address to make a 47 Direct IP Calling direct IP call after dial tone See Make a Direct IP Cal pO Enter 9 to reboot the device or E Enter MAC address to restore factory default setting See Restore Factory Default Setting section ge eea ecam ocam ocam oca ooa e ooa ooa ooa mm m e m gt m o mm m e m m gt ooa ooa m ooa ooa ooa mm e e m o m mm K am K am K e K r K r K m mr r K mm K m K m mm K m K m e m K m K m mm K r K m K m m e m K m K m K vr Invalid Entry Automatically returns to Main Menu ew oe gt gt ee coea oo ee ee oe oe oe oe ee oe oo ee gt ee oe oe oe oe oe oe oe oe gt gt oe on en en en en en etam etam gt gt ED gt am et ED gt en ew en ew ne en ee ee ee ees og RESET Five Success Tips when using the Voice Prompt 1 shifts down to the next menu option 2 ff returns to the main menu 3 9 functions as the ENTER key in many cases to confirm an option 4 All entered digit sequences have known lengths 2 digits for menu option and 12 digits for IP address For IP address add 0 before the digits if the digits are less than 3 i e 192 168 0 26 should be key in like 192168000026 No decimal is needed 5 Key entry can not be deleted but the phone may prompt error once it is detected 5 2 Placing A Phone Call
38. rates G 729A B E iLBC G 726 provides proprietary VAD CNG and signal power estimation Voice Play Out unit reordering fixed and adaptive jitter buffer clock synchronization AGC automatic gain control Status output Decoder controlling via voice packet header Voice Compression DHCP Server Client Yes NAT Router or Switched Moie T 38 compliant Group 3 Fax Relay up to 14 4kpbs and Fax over IP auto switch to G 711 for Fax Pass through Fax Datapump V 17 V 19 V 27ter V 29 for 1 38 fax relay Hanlong Technology Co Ltd Unicorn 600x User Manual Page 9 of 37 Firmware 1 0 0 29 Last Updated 8 2010 KS HAN LON CG TECHNOLOGY as wtsts S Diffserve TOS 802 1 P Q VLAN tagging IP Transport mmer flexible DTMF transmission method User interface of urm meer In audio RFC2833 and or SIP Info IP Signaling SIP RFC 3261 Provisioning TFTP HTTP HTTPS pending Syslog support HTTPS pending Telnet remote Management S using dE DialPlan e UPnP Support Yes Power t sS S Output 9VDC Input 100 240 VAC 50 60HZ Mounging Back mount Wall mount Desktop tS Short and long haul BENZ Upto150fton 24 AWG line lt i Gala TE ST KT T ems DING seer KES Ren C Polarity Reversal Wink Yes EMC EN55022 EN55024 and FCC part15ClassB 4 2 Hardware specification The hardware specifications of the Unicorn FXS series are detailed in Table 4 TABLE 4 Hardware Specif
39. rnet Telephone Service Provider User can download configuration from the web page and save to configuration file Using these settings users can configure tone frequencies and cadence according to their preference By default they are set to North American frequencies Configure these settings with known values to avoid uncomfortable high pitch sounds ON is the period of Unicorn 600x User Manual Page 26 of 37 Firmware 1 0 0 29 Last Updated 8 2010 Restore Configuration ringing On time in ms while OFF is the period of silence In order to set a continuous tone OFF should be zero Otherwise it will ring ON ms and a pause of OFF ms and then repeat the pattern Example configuration for N A Dial tone f1 350 13 f2 440 13 c 0 0 Syntax f1 freq vol f2 freq vol c on1 off1 on2 off2 on3 off3 Note freq 0 4000HZ vol 30 OdBm User can restore the before configuration from the configuration file saved at local pc 7 5 2 Profile Page Definitions Settings Options Account active SIP Server Outbound Proxy NAT Traversal Hanlong Technology Co Ltd PROFILE PAGE DEFINITIONS Definitions When set to Yes this profile is activated SIP Server s URI or IP address SIP Outbound Proxy Server s URI or IP address This parameter defines whether the Unicorn 600x NAT traversal mechanism will be activated or not If Choosing No nothing to do If Choosing No but send keep alive the Unicorn 600x will
40. s not indicate the transfer has been successful nor does it indicate the transfer has failed It often means there was a failure to receive second NOTIFY check firmware for most recent release Attended Transfer Assume that Caller A and B are in conversation Caller A wants to Attend Transfer B to C 1 Caller A presses FLASH on the analog phone for dial tone 2 Caller A then dials Caller C s number followed by or wait for 4 seconds 3 If Caller C answers the call Caller A and Caller C are in conversation Then A can hang Hanlong Technology Co Ltd Unicorn 600x User Manual Page 14 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY up to complete transfer 4 lf Caller C does not answer the call Caller A can press flash to resume call with Caller B NOTE When Attended Transfer fails and A hangs up the Unicorn 600x will ring back user A to remind A that B is still on the call A can pick up the phone to resume conversation with B 5 6 3 Way Conferencing The Unicorn 600x supports Bellcore style 3 way Conference Instructions for 3 way conference Assuming that call party A and B are in conversation A Unicorn 600x wants to bring C in a conference 1 A presses FLASH on the analog phone or Hook Flash for old model phones to get a dial tone 2 A dials 23 C s number then or wait for 4 seconds 3 If C answers the call then A presses FLASH to bring B C in the conference 4 If C does no
41. six different tabs STATUS Basic Settings SUPER Settings Profile 1 Profile 2 and FXS Ports on the top of the screen after login To open each page click on the tab 2 Click on Profile 1 to enter your SIP Server SIP Proxy Registrar information Enter the IP Address or FQDN of the Server under SIP Server and or Outbound Proxy 3 Click on FXS ports to enter the extensions or account information You will need to fill in the following information for each extension Once the extensions are configured you are finished i moro Neo DETTE Cc me pk LO de Pen vb Ri bk LL fe a Bk kb ifr ETT me bk em sk bk fete ETT H Pe fas bk LL ril 9 mes Jee ERREECHT DESCH Bk Lr 1896 4 Click Saveset after changing any setting and then Re boot to confirm changes 5 After reboot check the Status Page to confirm the extensions are successfully registered You can now use your standard phones connected to ports FXS1 to FXS8 to make calls 7 3 Important Settings The end user must configure the following settings according to the local environment NOTE Most settings on the web configuration pages are set to the default values Hanlong Technology Co Ltd Unicorn 600x User Manual Page 21 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY 7 3 1 NAT Settings If you plan to keep the gateway within a private network behind a firewall we recommend using STUN Server The following three 3 settings are useful
42. splayed time will be daylight savings time or not If set to Yes then the displayed time will be 1 hour ahead of normal time This parameter controls whether the device is working in NAT router mode or Bridge mode Need save the setting and reboot the device before the setting start to work Sets the LAN subnet mask Default value is 255 255 255 0 Base IP for the LAN port which functions as a Gateway for the subnet Default value is 192 168 22 1 Value is set in units of hours Default value is 120hr 5 Days The time IP address are assigned to the LAN clients Forwards a matching TCP UDP port to a specific LAN IP address with a specific TCP UDP port This contains the password to access the Web Configuration Menu This field is case sensitive If set to Yes the unicorn600x will respond to the PING Unicorn 600x User Manual Page 24 of 37 Firmware 1 0 0 29 Last Updated 8 2010 we aar HAN LONG ocr TECHNOLOG port command from other computers but it also is vulnerable to the DOS attack Default is No If this parameter is set to No the HTML configuration ET SEC MD EEE I e son T 7 5 Super User Configuration Log in to the Super User Configuration Page the same way as for the basic configuration page Log in using either of the following passwords admin or 1234 Screenshot Of Super User Configuration Login Screen Hanlong VOIP Device Configuration SOE 71 All Rights Reserved Hanlong Technolog
43. t answer the call A can press FLASH back to talk to B 5 Conference end after A hangs up 5 7 Hunting Group This feature allows user to setup a single SIP account on the gateway and have the ability to use all FXS ports to make receive calls Using this feature all ports active in same hunt group will have the same phone number and incoming calls will be distributed in a round robin manner among the ports active in that hunt group The number of hunting groups is limited by the number of ports each Unicorn gateway model has i e each port can be its own hunt group The most practical and efficient way to use hunt groups is to assign 2 or 3 ports to separate hunt groups One additional and popular way to use the Hunting Group feature is called multiplexed analog lines In this configuration a legacy PBX system with 8 FXO trunks can be connected to 8 Unicorn 6008 ports configured as a hunt group The Unicorn 6008 can be registered to a SIP server provider using only one phone number If the SIP service provider allows multiple calls to the same number the Unicorn 6008 will allow 8 concurrent calls to the same SIP number All office members can be reached remotely using the same phone number in round robin fashion Hanlong Technology Co Ltd Unicorn 600x User Manual Page 15 of 37 Firmware 1 0 0 29 Last Updated 8 2010 TECHNOLOGY Example Configuration of a typical Hunting Group 1 Configure the SIP account from your VoIP Service Pro
44. t status software version and MAC address of the phone BASIC OPTIONS Basic preferences such as date and time settings multi purpose keys and LCD settings can be set here Additional functions available to administrators are Super OPTIONS To set advanced network settings codec settings and XML configuration settings PROFILE X To configure each of the SIP accounts FXS PORTS To configure each of the FXS ports and Hunting Groups etc 7 4 1 Status Page Definitions Device Status Setting options Definitions MAC Address The device ID in HEX format This is a very important ID for ISP troubleshooting WAN IP Address This field shows IP address of device Product Model This product model is Unicorn600x Software Version Information of software System Up Time Shows system up time since the last reboot PPPoE Link Up NAT Indicates whether the PPPoE connection is up if the Unicorn600x is connected to DSL modem Indicate the NAT type behind which the device is when the stun feature is defined Port Status Shows several information regarding the individual FXS ports Example for Unicorn6004 FXS port 4 user has set Do Not Disturb FXS port user has set his calls to be forwarded unconditionally to ext 613 FXS port 2 user has set his calls to be forwarded to 614 when his phone is busy FXS port 3 user is not registered with his SIP Server Hanlong Technology Co Ltd Unicorn 600x User Manual Page 23 of
45. to LAN Port data from your PC to switch will be tagged with Data VLAN Tag IP address or Domain name of the STUN server This parameter specifies how often the Unicorn600x sends a blank UDP packet to the SIP server in order to keep the hole on the NAT open Default is 20 seconds Minimum value is 20 seconds Upgrade or provisioning through TFTP or TFTP server Upgrade Via select HTTP or TFTP mode Allow DHCP Option support 66 128 150 If select yes device will get server information from DHCP option and ignore the Config Server Path Option 66 TFTP server name if you select Upgrade Via gt TFTP HTTP server name if you select Upgrade Via gt HTTP Option 128 TFPT Server IP address if you select Upgrade Via gt TFTP HTTP Server IP address if you select Upgrade Via gt HTTP Option 150 TFTP server address if you selectUpgrade Via gt TFTP HTTP server address if you select Upgrade Via gt HT TP configure file would be authenticated before acceptance if set to Yes This parameter defines the URI or IP address of the NTP server which is used by the Unicorn 600x to set the current date time If set Yes device can get NTP server from DHCP option 42 If set to Yes the configuration update via keypad is disabled Default is No The IP address or URL of System log server This feature is especially useful for the ITSP Internet Telephone Service Provider Default is blank the feature is useful for the Inte
46. vider on FXS port 1 under FXS Ports webpage 2 Select Active under the Hunting Group drop box for FXS port 1 3 For the remaining ports say 2 3 and 4 select 1 for Hunting Group Ports 2 3 and 4 are now active members of the hunting group associated with port 1 This configuration will route all calls directed to FXS port 1 to ports 2 3 and or 4 in round robin fashion respectively if port 1 is busy You can configure the ring timeout on the Profile page Example configuration of a multiple hunt group FXS Port 1 FXS Port 2 FXS Port 3 FXS Port 4 FXS Port 5 FXS Port 6 FXS Port 7 FXS Port 8 SIP UserlD and Authenticate ID entered Hunting group set to Active SIP UserlD and Authenticate ID left blank Hunting Group set to 1 SIP UserlD and Authenticate ID left blank Hunting Group set to 1 SIP UserlD and Authenticate ID entered Hunting group set to Active SIP UserlD and Authenticate ID left blank Hunting Group set to 4 SIP UserlD and Authenticate ID left blank Hunting Group set to 4 SIP UserlD and Authenticate ID entered Hunting group set to Active SIP UserlD and Authenticate ID left blank Hunting Group set to 7 Hunt Group 1 contains ports 1 2 3 Hunt Group 4 contains ports 4 5 6 Hunt Group 7 contains ports 7 8 Please be aware the choice of 1 for ports 2 and 3 the choice of 4 for ports 5 and 6 the choice 7 for port 8 is required to indicate that the SIP account tied to port market as
47. y CO LTD 2005 2008 Super User configuration includes the end user configuration and Super configurations including SIP configuration Codec selection NAT Traversal Setting and other miscellaneous configuration 7 5 1 Super Configuration Page Definitions Super Options Setting options Definitions This contains the password to access the Advanced Web Configuration page This field is case sensitive Only the administrator can configure the Advanced Admin Password Settings page Password field is purposely left blank for security reasons after clicking update and saved The maximum password length is 26 characters only digit or letter Home NPA Local area code for North American Dial Plan This field defines the layer 3 QoS parameter which can Layer3 Qos be the value used for IP Precedence or Diff Serv or MPLS Default value is 48 Layer2 Qos Value used for layer 2 VLAN tag Default setting is blank Data VLAN Tag When using Bridge Mode Data VLAN Tag is supported Hanlong Technology Co Ltd Unicorn 600x User Manual Page 25 of 37 Firmware 1 0 0 29 Last Updated 8 2010 Stun sever is Keep alive interval Firmware Upgrade and Provisioning Authenticate Conf File NTP server Allow DHCP Option 42 to override NTP server Lock Keypad Update Disable Voice Prompt Syslog Sever Syslog level Download Device Configuration Call Progress Tones Hanlong Technology Co Ltd TECHNOLOGY when your PC connect

User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents