ALTO_S_ Manual
Contents
1. USER MANUAL ALTO S8 ALIO Si Thank you for choosing Kruger home appliances Please follow the recommendations and guidelines contained in this manual This way the appliance will give you consistent high performance and efficiency for many years to come Table of Contents Warnings amp Caution Characteristics Installation amp Usage Maintenance amp Cleaning 10 Product Specifications and Technical Parameters Total Power 300W 308W w Auto Clean Moe AAA Dimensions of Outer Adaptor 6 Circular 3 x 10 Dimensions 28 14 Width x 11 34 Depth x 7 Height A WARNING TO REDUCE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS PLEASE OBSERVE THE FOLLOWING 10 11 12 18 14 TS Installation work and electric wiring must be done by a qualified professional in accordance with local applicable codes and standards including fire rated construction The stainless steel structural housing may have sharp edges Be careful to avoid cuts and abrasions during installation and cleaning The hood must be placed at a minimum distance of 26 and a maximum of 30 from the cooktop for best capture of cooking impurities and a minimum distance of 28 from gas range Provide sufficient air for proper combustion and exhausting of gases through the chimney of the burning equipment to prevent backdraft Follow the heating equipment manufacturer s guideline and safety standards2. a push button switch on the front panel Both electronic controls of the KS300 and KS300i are shown below O ry GO mo F 0 A ote a2 Wy KS300i KS300 from left to right from left to right e Power e Power e OW e Low e Medium e Medium e High e High e Lights e Lights e IntelliClean INTELLICLEAN AUTOMATIC CLEANING SYSTEM A detergent tank is integrated into the structure of the range hood and a pump will automatically distribute cleansers onto both fans inside the unit when the INTELLICLEAN button is pushed Cleaning often can keep the inside of the rangehood clean and prolongs the life of the unit Operation Instructions 1 Pour both cleanser and water to the marked level on the provided refill container e Pour the mixture into the refill hole on the top left hand side of the range hood Be careful to not overfill the reservoir The volume of the reservoir is identical to the refill container 3 In the event of an overfill The overflowing cleaner mixture will travel down into the transparent oil capture tray below This will be an indication to cease filling the reservoir 4 Press the IntelliClean button on the right most side on the button controls to start the motor O The motor will discharge cleansers onto the fan at regular intervals to clean the inside of the range hood It will stop automatically once the cleaning cycle is finished 6 The oil capture tray will need to be removed and
3. place Remove the filters from the hood and then the bottom piece of the housing can come off Remove the wheel center cap and loosen the wheel set screw in order to disengage the wheel from its motorshaft Soak all the removed parts for 30 minutes in warm water with liquid soap Then wash with a nylon brush or a soft scouring pad Rinse and dry completely before reinstalling NOTE When reinstalling the fan align the end of the set screw with the flat notch on the motor shaft Follow these steps below to clean the exterior of the range hood Stainless steel is one of the easiest materials to keep clean Occasional care will help preserve its fine appearance for years to come ls 2 Hot water with liguid soap can remove most stains easily Always rinse the surface with clean water and wipe dry with a soft clean cloth to prevent water marks Harder to remove stains discolourations and persistent deposits can be removed with a non abrasive household cleaner or stainless steel polishing powder with a little water For stubborn stains and deposits use a scouring pad or soft bristle brush along with a stainless steel cleaner and water Always rub in the direction of the polished lines or grain of the stainless steel finish Avoid using too much pressure as it may mar the surface Do not allow deposits to remain for long periods of time Do not use ordinary steel wool or steel brushes to clean the range hood Do not allow
4. a Insert the power cable in the hood and tighten the wire clamp to screw in the cable 2 Align the hood s keyhole mounting slots over the 4 partially installed screws 3 Making sure the duct positions over the hood s duct adaptor push the hood against the rear wall Electrical Connection 1 Using provided wire connectors connect wires as follows BLACK to BLACK A WHITE to WHITE B GREEN to BARE or GREEN YELLOW C 2 Reinstall the wiring box converter And plug back all the small connectors inside the hood SJ Reinstall the bottom plate make sure that both grease guides are aligned with the holes pefore installing grease pan 4 Using long nose pliers pull out each of the grease guides then set them in a way their flange slightly protrudes above the bottom surface LIGHTING The range hood requires two type JCD 12V 20W max G 4 base halogen bulbs WARNING Always switch off the electrical supply before carrying out any operation or maintenance on the appliance La Remove the halogen bulb cover with a flathead screw driver Remove the bulb by pulling it out of its socket horizontally DO NOT ROTATE THE BULB gt Replace the bulb with an identical type JCD 12V 20W G 4 base halogen bulb DO NOT touch replacement bulbs with bare hands CAUTION The surface the cover of the bulbs and the bulbs themselves may be hot please use extra care when removing them OPERATION This range hood is operated using
5. ameter pilot holes at th epoints where mounting holes are marked 6 Insert 4 mounting screws leaving approximately 14 of thread exposed Hood Preparation 1 Remove the bottom panel of the hood by removing its 7 mounting screws Set aside the pottom panel once it has been removed 2 Remove the wiring knock out located at the top of the unit Oi Depending on the type of exhaust options you would like to go with Please skip ahead to vertical exhaust installation or horizontal exhaust installation Vertical Exhaust Installation 1 Install the small shut off plate or backdraft damper inside the back of the hood Fig 1 1 2 Install the small shut off plate or backdraft damper outside the back of the hood Fig 1 2 Fig 1 1 Fig 1 2 3 Install the rubber gasket Included on the top of the hood as shown below Fig 1 3 Fig 1 3 6 Circular Duct Installation Mount the 6 round duct on the top of the hood Uses 10 screws Seal with duct tape when finished 3 14 x 10 Rectangular Duct Installation o Mount the 314 x 10 duct onto the top of the hood Uses 5 Screws Seal with duct tape when finished 3 14 x 10 Rectangular Duct Horizontal Exhaust Installation Install the gasket onto the top of the hood Mount the shut off plate onto the top of the hood Seal with duct tape when finished Install the adaptor to the back of the hood using 6 screws Hood Installation L
6. emptied when the marked line on the side has been reached Precautions la Only specific rangehood cleaning detergent and dishwashing detergent can be used Using inappropriate cleaning liquids can clog the lines and damage the pump For more information on which cleaning solutions to use please contact the manufacturer or a local agent closest to YOU 2 Follow the water and cleanser mixture ratio closely The water to detergent ratio should be 5 1 3 Users are advised to clean the range hood once a day If may be cleaned more or less frequently depending on individual needs 4 When refilling the unit with cleansing mixture use only the container provided and take care to not overfill the reservoir O Always start the cleaning cycle with an empty oil capture tray This will prevent the tray from being overfilled by the refuse 0 Do not insert anything other than the cleansing mixture into the the refill hole T The refill container and reservoir are of identical volume The IntelliClean system will discharge any excess cleaner into the oil capture tray below MAINTENANCE amp CLEANING NOTE Before servicing or cleaning unit switch power off at the service panel This will prevent power from being switched on accidentally Follow these steps below to clean the fans manually k E K Disengage the small grease guard cups from the filters by turning them counter clockwise Remove the screw holding the filters in
7. filter Use proper pan size Always use cookware appropriate for the size of the surface element 2 CHARACTERISTICS Dimensions 00000 11 3 4 NF 22 1 4 INSTALLATION amp USAGE NOTE Carefully remove the blue coloured plastic protective film prior to final installation Description Connection This appliance should be mounted to the bottom of a standard wall cabinet If the hood must be mounted directly to the wall secure the hood to wall studs gt gt gt Ductwork can be installed vertically or horizontally Duct runs should be as short as possible Avoid the use of elbows and reducers Use duct tape to connect joints and sections instead of screws Do not use ducts smaller than the exhaust output on the hood Location Preparation VERTICAL DISCHARGE USING 6 ROUND DUCT ROOF cap OUTLET DIMENSIONS ADJUSTABL CABINETTOP VIEWS ELBOW S WALL CAP OUTLET DIMENSIONS ADJUSTABLE CABINET TOP VIEWS ELBOW i T WALL CAP CABINET BUTTOM VIEWS 1 Use the dimensional drawings above to lay out the range hood s mounting holes wiring access and ductwork Mark the cabinet bottom and drywall where applicable a Make a cutout for the wiring and duct work 3 Install the ductwork so that it is flush with the range hood s mounting surface 4 Run two conductor wires from a power source to the hood location Bring approximately 12 of wiring through wiring hole 5 Drill 3 32 di
8. salt solutions disinfectants bleaches or cleaning compounds to remain in contact with the stainless steel surface for prolonged periods of time Many of these compounds contain chemicals that can be harmful to the stainless steel finish Always rinse with water after every cleaning and wipe dry with a clean cloth 10 ALTO and KRUGER ZENISS are all subsidiary development branches of KRUGER electrical appliances LTd 2011 All rights reserved U For more information on how to care for your kitchen ventilation unit please contact us at www krugerliving com L LISTED
9. such as those published by the National Fire Protection Association and the American Society for Heating Refrigeration and Air Conditioning Engineer ASHRAB and the local code authorities Ducted fans must always be vented to the outdoors This appliance is designed to be operated by adults Children are not allowed to tamper with the controls or play with this appliance To reduce the risk of fire or electric shock do not use this fan with any solid state speed control device When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities This unit is meant for household kitchen use only To ensure your safety it needs to be connected to a GFCI protected branch circuit Before servicing or cleaning unit switch power off at the service panel This will prevent power from being switched on accidentally Use this unit only in the manner intended by the manufacturer If you have any questions regarding the usage of this appliance please contact the manufacturer or the local agent closest to you Never leave surface units unattended at high settings Over boiling can cause smoke and grease spills that may ignite Heat oils slowly on low or medium settings Always turn hood ON when cooking at high heat especially when there is an open flame le Crepes Suzette Cherries Jubilee Peppercorn Beef Flambe Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or
Download Pdf Manuals
Related Search