Wireless Door Chime
Contents
1. E installation This equipment generates uses and can radiate radio frequency energy and if not installed and used i re ess O O i i mMm e in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or h d e more of the following measures C g Reorient or relocate the receiving antenna with om pact Backl It Des n Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING Modifications not approved by the party responsible for compliance could void user s authority to operate the equipment MDC810B020712E Operating Guide Thank you for choosing the Swann Wireless Doorbell It s an ideal unit for easily installing a doorbell without the hassle of wiring Simply add some batteries mount the two pieces where needed and you are Q ready to go The doorbell features 16 chimes and four levels of volume to suit your needs and can reach a distance of up to 100m approx 330ft when there are no obstructions Doorbell Doorbe Receiver Mounting the doorbell speaker The doorbell is mounted by simply sticking it to a wall using the included adhesive strip s e Peel off one side2. of the adhesive strip and attach it to the rear of the backing plate ensuring none of it is visible from the front e Find the area you want to mount the doorbell Flat smooth surfaces are ideal Make sure they are clean and dry before mounting e Peel off the other side of the adhesive strip and attach the doorbell to the mounting surface Mounting the receiver speaker unit There is no requirement to mount the receiver You may find it more convenient to place it ona shelf or table One of the benefits of a battery operated wireless doorbell is that if you have a large house you can take the receiver with you No more missing visitors because you were all the way at the back of the house or by the pool If you would like to mount the device you simply need to attach the two screws to a wall Place them level to each other about 24mm 15 16 apart Depending on the surface you may need to drill guide holes and or use masonry plugs or dry wall anchors Do not insert the screws all the way Leave about 7mm 4 protruding from the wall Then place the unit onto the screws ensuring the heads of the screws pass through the two mounting holes on the rear of the unit You can then shift the unit downwards to ensure it sits on the screws firmly WARNING When fitting the screws into the wall make sure you are not inserting them anywhere near electrical wires including wires that may be behind the wall If you are unsure at a
3. e aa Swann Technical Support All Countries E mail tech swannsecurity com Ss Telephone Helpdesk USA toll free AUSTRALIA toll free nE 1 800 627 2799 1300 138 324 SS Su 2pm 10pm US PT M 9am 5pm AUSE M Th 6am 10pm US PT Tu F 1am 5pm AUS ET F 6am 2pm US PT Sa 1am 9am AUS ET USA Exchange amp Repairs NEW ZEALAND toll free SS 1 800 627 2799 Option 1 0800 479 266 M F 9am 5pm US PT UK a 0203 027 0979 See http www worldtimeserver com for information on time zones and the current time in Melbourne Australia compared to your local time E Swann Communications USA Inc Swann Communications Swann Communications LTD 12636 Clark Street Unit 13 331 Ingles Street Stag Gates House p Santa Fe Springs CA 90670 Port Melbourne Vic 3207 63 64 The Avenue USA 60171XS United Kingdom ns on certain exclusions in this warranty ights v ke precedence with guarantees which cannot be excluded under Australian Consumer ment or refund for a major failure and for compensation for any other or damage You are also entitled to have the goods repaired or replaced if the cceptable quality and the failure does not amount to major failure FCC Verification This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential E
4. ll please get a professional to check first and install the screws for you Operating current receiver unit 4 5V 3 x AA Batteries not included Operating current doorbell unit 12V 1 x CR2032 Battery included Transmission Frequency 433Mhz Transmission Range Up to 100m 330ft line of sight 50m 165ft typical Internal Sounds 16 chimes Batteries Receiver e The doorbell receiver unit requires 3 x AA batteries to operate which are not included For best performance use fresh high quality AA alkaline batteries e To install them unclip the battery cover on the rear of the unit to reveal the battery compartment e The polarity of batteries is indicated by the markings inside the battery compartment Batteries Doorbell unit e The doorbell requires 1 x CR2032 battery included e To access the battery pry off the back cover using a small flat head screwdriver in the small notch at the bottom of the doorbell e To finish clip the back cover back onto the doorbell unit making sure the rubber seal is fitted properly to ensure the unit remains water resistant Setting the volume and chime e To change volume press the volume button on the side of the receiver unit This switch toggles between High and Low volume e To change chimes press the chime select button on the side of the unit The unit will play the next chime Keep pressing the button until you hear a chime you like You do not need to confirm y
5. our selection The chime playing is the chime selected and the one which will be heard when the doorbell is pressed e The new chime sound will be set for the most recently pressed Doorbell If you ve paired multiple Doorbells then you can set the chime for each one independently Volume button Chime select Pairing a Doorbell to the Receiver button e Press the Pairing Button on the Chime Unit The button is small and recessed so you ll need a matchstick or similar to press the button e Press the button on the Doorbell Unit e The Doorbell is now paired with the Chime unit See above for instructions on setting a chime sound specific to that Doorbell Pairing Button
Download Pdf Manuals
Related Search