GETCP Supplementary File - getcp
Contents
1. CP30 for GE 90 30 CPU GETCP70 for GE 90 70 CPU NumberNetwork number redundancy Port name Port name as used on Ports form Address Not used IO Device variable types IO Device Citect data Description Minimum Maximum Type type Address address J 1 System register 16384 SB U DIGITAL System memory B SC U DIGITAL System memory C AI U Analog input 8192 AQ U Analog Output 8192 0 683 Read only _ jo PLCF U BYTE PLC Fault bytes 683 Read only IOF U BYTE IO Fault bytes 1355 Read only The maximum address value supported by the driver are given above but the actual values should be set to correspond with the addresses available in the attached PLC Parameters and INI options Standard Parameters Block 256 Delay 0 MaxPending 8 Polltime 0 Timeout 1000 Retry 1 WatchTime 30 Special Parameters MaxFrameBytes 2048 The maximum size of the combined read data request to the PLC PROTDIR DBF PROTDIR DBF should have an entry for this driver as follows Bit Bloc Max k Length GETCP30 GE30 1024 2048 Ox3ff GETCP70 1024 2048 Ox3if GE70 DBF Template Unit type Raw type Bit width Low High Comment jm 2 Cd tf 12288 Digital input u 3 Jo dt 12288 Digital Output Global 26 A sc u 23 Jo PLeF U 20 fae 8 Jo 683 PLC Faultbytes RO__ ioF u 21 e 8 jo 1355 10 Fault bytes RO___ Driver Specific Errors Driver specific errors will be in the form 1xxxx example 105f42. Citect for Windows Driver Specification GETCP Driver Author Peter Barker Tel 4182611 Date Thursday January 18 1996 Modified by Date Philip Wong fe Sean Ju 15 5 96 Trevor Hudson 28 5 98 Contents TARGET DEVICE AND PROTOCOL 2 Device Manufacturer 2 Device Definition 2 Host Requirements 3 Communications Configuration 3 Using GEnet System Manager GSM 3 USER INTERFACE 3 Driver Name 3 Boards Form 3 Ports Form 3 IO Device Form 3 IO Device variable types 4 Parameters and INI options 4 Standard Parameters 4 Special Parameters 4 PROTDIR DBF 4 GE70 DBF 5 Driver Specific Errors 5 REFERENCE CONTACTS 5 Target Device and Protocol Device Manufacturer GE Fanuc Automation North America Inc Device Definition This driver provides communication with GE Fanuc Series 90 70 and 90 30 PLCs using Winsock TCP IP An ethernet card with software providing a Winsock TCP IP stack must be installed in the PC before this driver can be used The Citect TCPIP driver is used to access winsock Host Requirements Network card for ethernet Winsock TCP IP software for above network card available from Microsoft for Windows for Workgroups 3 11 Windows 95 and Windows NT 8 MB RAM 80386 or better CPU This drivers does not requires any software from GE to run on the computer Communications Configuration The TCP IP network must be properly configured before installing this driver In Windows for Workgroups this can be done usi
3. Invalid input parameters in request 105c3 Text length doe not match traffic type For complete list of errors see Table A 8 PLC CPU Error Codes in Host Communications Toolkit for C C Applications User s Manual GEC Fanuc Automation manual number GFK 0870A January 1995 Reference Contacts e Graeme Sutton Project Manager Driver Development Ci Technologies Pty Ltd Tel 61 2 98551000 Direct 61 2 94977003 Fax 61 2 94889164 E mail GraemeSutton cit com au
4. ng Windows Setup in Main Group of Program Manager Select Change Network Settings and set up the TCP IP protocol In Windows 95 amp NT this can be done using Network utility in Control Panel In particular the correct values for IP Address subnet mask and default gateway must be set See your network administrator for details This setup can be tested by using PING to check a response is received from the PLC Open a DOS window and type c windows ping a b c d where a b c d is the IP address of the PLC A response should be received You should also receive a response if you ping the address you assigned for your local PC Using GEnet System Manager GSM The GSM software is required to configure the IP address of the Ethernet controller in the PLC See Appendix C for procedure Using LM90 for later versions of Ethernet Interfaces The LogicMaster software is required for rack and IP address configuration of module CMM 742 Ethernet modules and CPM 925 CPU this may also be the case for other models not tested See Appendix C for procedure User Interface Driver Name GETCP Boards Form Board Type TCPIP Address Must be set to 0 IO Port Not used Special Opt Not used Ports Form Port Name Port name Port Number Not used Baud Rate Not used Data Bits Not used Stop Bits Not used Parity Not used Special Opt IA where A is the IP address of the Ethernet Controller module in the GE PLC rack IO Device Form Protocol GET
Download Pdf Manuals
Related Search