Assembly & Instruction Manual
Contents
1. AE mi amp Instruction Manual Congratulations on your purchase of the Atomic A2 Motion Simulator from JoyRide This guide will talk you through setting the system up for first use safety precautions and recommendations for maximising the life of your system For software instructions please refer to the software user guides available via their respective help systems IMPORTANT Please read this manual in full before attempting to assemble or use the Atomic A2 Failure to do so may result in damage poor performance reduced system life or injury Table of Contents Unpacking and Setting Up Base Unit and Seat Foot Rest Pedal Mount Steering Wheel Yoke Mount Shifter Mount COG Setup Wiring Operation Safety Precautions Hints and Tips Firmware Update DMX Channel Assignments Troubleshooting p 3 p 4 p 5 p 6 p 7 p 8 p 9 p 11 p 12 p 13 p 14 p 15 p 16 Unpacking and Setting up Racing Flight System HOTAS Fighter System Recommended Tools Allen Keys Cable Ties or Velcro Straps for securing controller cables System Components Checklist Most system components are factory pre assembled Depending on configuration these consist of Atomic A2 Base Unit Foot Rest Pedal Mount Steering Wheel Flight Yoke Mount Racing Flight System Only Shifter Throttle Flight Stick Mount x1 for Racing System x2 for HOTAS amp Fasteners USB2. turn anticlockwise release the button and further tighten clockwise 5 Centre Of Gravity COG Setup Diagram 5 COG Setup In order to maximise the performance of your system it is important the COG is configured correctly based on the controllers you wish to use some pedal sets are significantly heavier than others for example Prior to configuring the COG ensure you have fully assembled the unit attached your controllers and adjusted everything for comfort by following the instructions in sections 1 4 It is recommended a second person is available to assist when configuring the COG NOTE Significantly incorrect COG settings can be detrimental to performance and reduce actuator life 5 1 Ensure the power is OFF allowing the platform to move freely on the pitch axis 5 2 While seated in the unit with the harness attached ensuring your back is flat against the rear of the seat loosen the left and right COG adjustment levers diagram 5 1 by turning anticlockwise 5 3 With an assistant supporting the rear of the seat slide the top platform forwards or backwards diagram 5 2 until when level it remains balanced above the unit s base does to fall to the front or rear when the assistant lets go Note it is unimportant if the system falls slightly to the left or right of the roll axis 5 4 When satisfied the COG is configured correctly retighten the left and right COG adjustment levers If further tightening is required
3. best results If possible secure your controllers firmly to their mounts using the mounting holes provided To enhance the feeling of forward acceleration it is more advisable to tilt the seat inclination reclination further backwards using the mechanism described in section 1 rather than offsetting the centre position of the unit in your software This allows the system to still be able to respond to the greatest range of pitch motion possible for both acceleration and braking If you are unsure it is recommended you set the seat inclination reclination to about halfway for most applications If you are using force feedback controllers use a high force setting the Atomic gives a substantial amount of force feedback so if your usual controller force settings are low they may get a little lost in the experience For additional immersion and a better perceived motion experience it is highly recommended either headphones or a loud audio system is used For increased immersion still use a large 3D ready screen projector multi screen surround or Virtual Reality HMD setup If possible remember to switch off the lights Look out for future immersion enhancing products from JoyRide including our forthcoming TornadoTM stereoscopic high velocity wind system Device Firmware Update DFU From time to time it may be necessary to update the firmware of your Atomic as JoyRide introduces additional functionality This is done via the
4. Cable IEC Power Cable Seat amp Seat Fasteners 3 Point Safety Harness amp Fasteners 1 Base Unit amp Seat Diagram 1 Base Unit 1 1 Remove the Atomic A2 base unit from its packaging and situate it on a level stable operating surface for intended use WARNING Never lift the base unit by the plastic housing or damage may result to the mounts the housing is floating for safety reasons Always lift from the front and rear of the top table diagram 1 5a 5b 1 2 When a user is seated the 3 rubber support feet diagram 1 1a 1b on the base of the unit should be making good contact with the ground These are factory set and should not be adjusted manually the rear castor wheels should be barely making contact with or just higher than the ground 1 3 Retract the two front supporting legs diagram 1 2 fully to provide additional stability NB ensure the front support foot diagram 1 1b is also making contact with the ground so the legs themselves are not baring the full weight of the platform and user 1 4 Attach the seat to the base unit using the 4 mounting screws provided NB 2 sets of mounting holes are provided for compatibility with a variety of base mounted seats Please ensure the correct ones are used and the seat is mounted centrally 1 5 Thread the harness through the seat and attach to the left right and rear mounting points provided 1 6 For further stability mounting holes are provided on the botto
5. JoyRide DFU Device Firmware Updater which is a software utility available freely from JoyRide for your Windows compatible PC To update your device s firmware 1 Ensure power is connected to the system and the system is connected to your PC via the supplied USB cable 2 Ensure the JoyRide DFU is correctly installed on your PC this also installs the required drivers to update your firmware 3 Put the Atomic in DFU mode Using a pair of pointed implements e g Ballpoint pen press and hold the F function button on the Atomic s I O panel section 6 diagram 6 9 4 Keeping the F function button held down press and release the R reset button on the Atomic s I O panel section 6 diagram 6 8 5 Finally release the F function button The device is now in DFU mode 6 Follow the on screen instructions provided with the JoyRide DFU to perform the firmware update and once complete disconnect and reconnect both the power and USB leads to the Atomic DMX Channel Assignments The Atomic A2 can be controlled using a conventional DMX control desk The channel assignments are as follows NB remember to offset the channel number by your chosen base channel Channel 1 Range 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 Title Pitch Coarse Pitch Fine Roll Coarse Roll Fine Force Max Speed TT Gain TTi Units only TT LFC TTi U
6. e Adjustment Reach To adjust the reach leg length for comfort follow steps 2 1 and 2 2 above Tilt To adjust the tilt of the pedal set remove the left and right thumb screws diagram 2 1 tilt the footrest to the desired position and reinsert the left and right thumb screws ensuring they are correctly inserted into on of the indexing holes and the footrest is secure 3 Steering Wheel Flight Yoke Mount Diagram 3 Wheel Yoke Mount 3 1 Attach the bottom of the wheel yoke mount to the foot rest using the 6 fasteners provided ensuring they are tight and the wheel yoke mount is secure 3 2 Attach your steering wheel or flight yoke to the steering wheel table via the clamp bar and if additional stability is required also the holes provided These are compatible with the following controllers but may be usable for others Logitech G27 G27 steering wheel Saitek Pro Flight Yoke PZ44 Adjustment Height Retract the steering height adjustment knob diagram 3 1 by lifting and turning to lock it in its retracted position Adjust the steering wheel mounting assembly to the desired height position and release the adjustment knob by turning clockwise ensuring it locks correctly into place in one of the indexing holes and the steering wheel table is secure Tilt To adjust the tilt of the wheel yoke for comfort loosen the left and right thumb screws diagram 3 2 and tilt the control table to the desired positi
7. ed using either a PC via SIMPHYINTY software or similar or DMX capable controller For further instructions please consult either the software or DMX controller manual Safety Precautions Ensure power to the unit is switched off when not in use While not essential it is recommended the harness is worn at all times for added safety Ensure spectators are kept at arms length when the unit is in operation and there are no obstructions in or around the base or foot rest Ensure loose clothing is not in the proximity of any moving parts to reduce the risk of trapping or injury For maximum stability the base should be mounted on a flat level surface with the front support legs extended and all support feet making good contact with the ground when a user is seated The rear castors should be just above or barely touching the ground As with any other highly dynamic system it is good practice to check all adjustment levers fasteners are tight and secure before each use The Atomic is a highly durable system however it is necessary to provide some user releasable mechanisms to facilitate rapid comfort adjustment It may be preferable in heavy use situations e g commercial scenarios to replace hand adjustable levers and fasteners will tooled alternatives Ensure users keep their feet on the foot rest pedal mount at all times while the unit is active to prevent trapping or injury Adjust the system for comfort prior to operat
8. ion ensuring the user s limbs can move freely and easily It is strongly recommended the safety interlock mechanism is activated via the emergency stop button when entering or exiting the seat to reduce the risk of injury in case unexpected motion occurs When in use it is strongly recommended pitch roll movement range settings do not allow the actuators to hit their end stops indicated by a knocking sound when the pitch or roll reaches the end of its travel Under normal use there is a protection mechanism to prevent this however if abnormal loads are applied there is a slim possibility this can be defeated potentially damaging the actuators due to excessive shock If you feel this is happening reduce your pitch roll movement range settings Take care when entering and exiting the seat sudden impacts can result in excessive load shock to the actuators The actuators feature an overload protection mechanism which quickly disconnects power to the relevant actuator in these circumstances should this happen you will need to reset the unit by disconnecting and reconnecting both power and the USB cable Hints amp Tips Adjust your system fully to find the perfect driving position before starting The Atomic provides extensive adjustment to simulate many different types of vehicle layout which can greatly enhance the feel of the system when configured properly Ensure the COG is configured correctly for the control set and user
9. k TT Gain software settings refer to software user manual JoyRide Unit 12 Vancouver Wharf Hazel Rd Southampton SO19 7BN UK 44 0 870 3146413 www joyridesimulators com 17
10. m of the base unit to allow it to be secured to a platform if desired Please contact JoyRide for further information and advice Adjustment Seat Inclination Angle To adjust the seat inclination reclination tilt loosen the left and right inclination levers diagram 1 3 by turning anticlockwise Adjust the seat to the desired inclination then retighten the levers by turning clockwise If further tightening is required press and hold the red button on the lever disengaging it from the tightening mechanism turn anti clockwise release the button and further tighten clockwise 2 Foot Rest Pedal Mount Diagram 2 Foot Rest Pedal Mount 2 1 Retract the footrest adjustment knob on the base unit section 1 diagram 1 4 by pulling it up it can be turned at the top to lock it in its retracted position 2 2 Insert the footrest to the desired position and release the footrest adjustment knob ensuring it locks correctly into place in one of the indexing holes and the footrest is secure 2 3 Attach your pedal set to the foot rest via the mounting holes provided These are compatible with the following controllers but may be usable for others Logitech G27 G27 pedal set Saitek Pro Flight Rudder Pedals PZ35 NB If your pedal set is incompatible with the foot rest mounting holes straps can be used instead however JoyRide strongly recommends additional holes are drilled to provide additional stability where possibl
11. mplifier DMX Network Setup Optional If you have a multiple units or devices you wish to link together to operate in unison this is achieved via the DMX networking capability Devices can be controlled using either your PC or a DMX compatible control desk see the DMX Channel Assignments section on p 15 Additional cables required unsupplied 1 or more standard RJ 45 PC network cables Optional control desk only 1 x 3 or 5 pin XLR depending on the output from your DMX control desk gt RJ 45 DMX cable PC Controlled 6 5a Connect the first Atomic in the chain to your PC using the supplied USB cable as described above 6 1 6 6a Connect one end of the RJ 45 cable to the DMX Out diagram 6 5 port on the first Atomic in the chain to the DMX In diagram 6 6 port on the second Atomic 6 7a For each subsequent unit you wish to control simultaneously connect another RJ 45 cable from the DMX Out port of the previous unit to the DMX In port of the next DMX Desk Controlled 6 5b Connect the DMX In port diagram 6 6 of the first Atomic in the chain to your DMX control desk using the XLR gt RJ 45 DMX cable 6 6b Chain subsequent units together by following steps 6 6a 6 7a above Dip Switch Settings The DMX512 address of the unit is set using switches 1 9 on the ADDR TERM switch panel diagram 6 7 As with most DMX compatible equipment the addresses are set using a binary system by summating
12. nits only Command Description Coarse pitch position 0 fully backward 255 fully forward Fine pitch position Used in conjunction with Pitch Coarse to form a 16 bit number allowing 65536 possible positions Pitch Coarse is the high order byte Coarse roll position 0 fully left 255 fully right Fine roll position Used in conjunction with Roll Coarse to form a 16 bit number allowing 65536 possible positions Roll Coarse is the high order byte Movement force 0 lowest 255 highest Movement maximum speed 0 lowest 255 highest If unsure set this to be permanently 255 Sets the gain volume of the tactile transducers 0 lowest 255 highest Sets the LFC Low Frequency Cut off of the tactile transducers 0 lowest 20hz 255 highest 100hz Used to issue one shot commands to the unit Must be set to 0 at all other times Commands are as follows 255 Reset system It is recommended the command channel is set to the desired value for a minimum of 0 5 seconds before being reverted back to zero to ensure the command is transmitted correctly Problem No motion one or more actuators move freely No motion actuators locked in place Poor motion output Troubleshooting Possible Cause s Power disconnected Actuator overload safety mechanism defeated Safety interlock activated red LED and Atomic logo will be illuminated Incorrect
13. on Retighten the left and right thumb screws Reach Loosen the left right levers diagram 3 3 by turning anticlockwise adjust the reach to the desired position and retighten the levers If further tightening is required press and hold the red button on the lever disengaging it from the tightening mechanism turn anti clockwise release the button and further tighten clockwise 4 Shifter Throttle Flight Stick Mount Diagram 4 Shifter Throttle Stick Mount 4 1 Attach the shifter mount diagram 4 1 to either the left or right side of the base unit using the fasteners provided 4 2 Depending on which side you have chosen you may need to resituate the shifter mounting plate by removing and replacing the fasters shown in diagram 4 3 Adjustment Height The base level height can be switched between 3 positions by removing the levers diagram 4 2 and reattaching them in the desired position as shown The height can also be changed along with the reach by loosening the levers see below Reach The base reach can be switched between 2 positions by resituating the shifter mounting plate diagram 4 3 The reach can also be changed along with the height by loosening the levers diagram 4 2 To do this turn them anticlockwise adjust the reach height to the desired position and retighten the levers If further tightening is required press and hold the red button on the lever disengaging it from the tightening mechanism
14. press and hold the red button on the lever disengaging it from the tightening mechanism turn anti clockwise release the button and further tighten clockwise 5 5 In situations where many users will be riding e g commercial settings it is recommended the COG is configured for an average height user 5 5 160cm approx to obtain the best results 6 Wiring Diagram 6 Electronics Panel 6 1 Connect the supplied USB lead to the USB port diagram 6 1 on the Atomic and the other end to any available USB 2 0 or above port on your computer 6 2 Connect the supplied IEC Mains lead to the Power port diagram 6 2 on the Atomic and the other end to any available mains socket Amplifier Wiring TTi Units Only If you have a TTi enabled unit the following additional unsupplied cables are required 1 x 3 5mm male gt 3 5mm male jack cable 1 x 3 5mm male gt 2 x Phono L R audio jack cable optional 6 3 Connect one end of the 3 5mm male gt 3 5mm lead to the Speaker Headphone Out port on your PC please refer to your PC s instruction manual if you require more information and the other to the Audio IN port diagram 6 3 on the Atomic 6 4 Connect your headphones or PC speakers to the Audio OUT port diagram 6 4 on the Atomic Alternatively if using a hi fi amplifier connect the 3 5mm gt 2 x Phono cable between the Audio OUT port diagram 6 4 on the Atomic and any available line input on your a
15. push the housing down and activate one or more of these switches stopping the motion and locking the actuators in their place to prevent further movement The emergency stop button is the big red button marked X section 1 diagram 1 10 located to the right of the seat and when pressed will also stop the actuators preventing further movement When either the trap detection mechanism or emergency stop button is activated the system will go into safety interlock and this condition will be highlighted by the red LED next to the emergency stop button the Atomic logo will also turn red NOTE pressing the emergency stop button quickly will lock the actuators in their place pressing and holding for longer than 4 seconds will disconnect power to the system completely To exit the safety interlock mode and resume normal operation press the black ON button marked 1 section 1 diagram 1 11 adjacent to the emergency stop button Indicator LEDs When the unit is ON the power LED section 6 diagram 6 11 will be illuminated While the unit is IDLING awaiting data it shall return to its centre position and the status LED section 6 diagram 6 10 will blink slowly When the unit is ACTIVE receiving motion data the status LED section 6 diagram 6 10 will blink rapidly When the unit is in SAFETY INTERLOCK MODE the red LED next to the emergency stop button will be illuminated Software The Atomic can be controll
16. software settings Incorrect DMX channel setting Incorrect software settings Incorrect COG configuration Possible Solution s Check power is connected and AC power light is illuminated If power is connected disconnect power and USB then reconnect Disengage the safety interlock by pressing the black ON button marked 1 Ifthe red LED Atomic logo remains illuminated check the base plastic cover is free from obstruction and not pressing down on any of the 4 safety switches Ensure USB cable is correctly connected and system is present in Windows Device Manager refer to Windows manual Check software settings to ensure system is enabled and force or pitch roll movement range settings are not 0 refer to software user manual Check game has been recognised in software and motion preview is showing movement Check DMX channel is set correctly and corresponds with that in software refer to software user manual Increase pitch roll movement range and or force setting in software refer to software user manual Correctly configure the COG Problem Possible Cause s Possible Solution s No or poor Tactile Transducer Audio cables not correctly Ensure audio cables are feedback TTi units only connected properly connected PC sound output is set to full and audio PC sound output low or muted cable is connected to correct port on soundcard Chec
17. the values of all enabled on switches 1 9 to give the address e g switch 1 enabled on and 2 9 disabled off Channel 1 switches 2 and 4 enabled and all others disabled Channel 10 and so on Units set with the same address in the chain will operate in unison IMPORTANT Switch 10 should only be enabled on in the LAST unit in the DMX chain this enables the termination resistor and if left disabled off unexpected results may occur If it is enabled on a unit prior to the last in the chain the subsequent units may not function correctly If you are unsure about DMX channel setup or will only be using a single Atomic via PC control just set the unit to channel 1 by enabling switch 1 on and disabling all others off Power Operation Once power is connected to the unit ensure the AC power switch is on section 6 diagram 6 12 The AC switch will illuminate when the unit is in operation The unit should now home to its centre position ready for operation If this does not happen please read the Safety Interlock Mechanism instructions below You can also refer to the Troubleshooting section Safety Interlock System The unit has a number of safety features including a trap detection mechanism and emergency stop button The trap detection mechanism consists of 4 switches one at each corner of the base where the housing is attached in the event a trapped foreign body is detected while motion is active this will
18. to maximise performance If many users are to be using the system e g in commercial situations configure the COG for an average height person described in section 5 for optimum results Use of the harness does not only provide added safety but when tightly secured can significantly enhance the motion sensation This is particularly applicable to highly dynamic applications such as racing or rallying where road surface detail typically produces smaller movements some of which may not be perceived due to the natural shock absorption of the upper body with respect to the seat The Atomic can provide exceptionally fast motion response compared to many other systems and use of the harness maximises this benefit Experiment extensively with your software settings to fine tune your ride in particular force level and pitch roll movement range As with any other system incorrect settings may yield disappointing motion results but a correctly tuned system can produce an incredible experience Sometimes less is more excessive force settings can result in overshoot producing a jittery feeling in flight type applications and excessive pitch roll movement range settings can reduce the response of the system to more subtle feedback such as road surface detail If you have a TTi unit ensure your line level input connected to the Audio IN port on the Atomic has a strong signal and the volume output on your computer is set to maximum for the
Download Pdf Manuals
Related Search