SM2560A RC Projection Clock
Contents
1. Receiving the MSF Time CODE The projection clock will automatically receive the MSF time code every hour Besides you can force the clock to receive the signal by pressing Wave It will take 3 10 minutes to receive the radio signal It the time signal is received the icon will be on otherwise it will be off PRECAUTIONS This product is engineered to give you years of satisfactory service if you handle it carefully Here are a few precautions 1 Do not immerse the unit in water 2 Do not clean the unit with abrasive or corrosive materials They may scratch the plastic parts and corrode the electronic circuit Do not subject the unit to excessive force shock dust temperature or humidity which may result in malfunction shorter electronic life span damaged battery and distorted parts Do not tamper with the unit s internal components Doing so will invalidate the warranty on the unit and may cause unnecessary damage The unit contains no user serviceable parts Only use fresh batteries as specified in the user s manual Do not mix new and old batteries as the old ones may leak Always read the user s manual thoroughly before operating the unit Used batteries shall be disposed off environmentally beneficials Do not throw away the article but dispose off environmentally beneficials Use existing collecting points or special waste dumps for this purpose 10 Please don t use the rechargeabl2. P key for 3 seconds the icon G will turn on e Press and hold MODE for 3 seconds in Foreign Time display The Foreign time can be set as described above by pressing or key e Press MODE key again to confirm the setting of foreign time e Press and hold key for 3 seconds to choose between local and foreign time display Setting the Dual Time e The dual time can be set by pressing MODE for 3 seconds in Dual Time Display The hour will flash for input e Press MODE the hour of dual time display digits are blinking and can be set by pressing or key e Press MODE again the minute of dual time display digits are blinking and can be set by pressing or key e Press MODE again to confirm the setting Light ON OFF e Press top button SNOOZE LIGHT key light will come on and turn off automatically after 5 seconds Projection Light and its adjustment To keep the projection continuously insert an AC DC adapter AC 230V 50Hz DC 3V 100mA and turn the Continue Projection Switch to on position Projection can be turned off by Switching off the Continue Projection Switch or Switching off the mains switch and removing the adapter e Press SNOOZE LIGHT Projection light will come on and turn off automatically after 5 seconds e Press FLIP key to rotate the projection image in 180 orientation clock wise Attention Please dispose of used batteries in an ecologically safe manner
3. RADIO CONTROLLED PROJECTION CLOCK Model No 2560 TIME SET NILBRAND ZEON PCR102 MANUAL ENG SIZE W65 X H105 mm BY SHAN WONG 27 03 06 INDICATOR STANDING FOR INDICATOR STANDING FOR RADIO SIGNAL RADIO SIGNAL WEAKLY DATE REPEAT ALARM INDICATION PM 12 HR DISPLAY ONLY AM 12 HR DISPLAY ONLY DUAL TIME SUMMER TIME INDICATION DUAL TIME ALARM E eal ALARM 2 C al To install the AC DC adapter for Continue Projection Please make sure your household voltage matched with the voltage supported by the adapter or it will damage your clocks and adapter Use 2 X AA R6 UM 3 1 5V batteries and AC DC adapter AC230V 50Hz DC3V 100mA not included p A y i i M gy e After the batteries are installed the LCD will turn on and beep for 2 seconds The clock will automatically search the radio signal It takes about 3 10 minutes to finish this process e If the radio signal is received the date amp time will be set automatically with radio control signal icon turns on e Ifthe clock fails to receive the time signal it will be in Time Temperature display with the icon turns off Then user can set the time manually e Radio controlled signal will be scheduled to receive every hour Selecting Alarm 1 Alarm 2 Dual time Display e Press MODE will display the ALARM 1 time e Press MODE again will display the ALARM 2 time e Press MODE again will dis
4. e batteries
5. ng In the ALARM 1 Display e Press MODE for about 3 seconds the hour digits are blinking and can be set by pressing or key e Press MODE again the minute digits are blinking and can be set by pressing or key e Press MODE again the Alarm time is set and SY icon will turn on ALARM 2 setting i In the ALARM2 Display aTe e Press MODE for about 3 seconds na y the hour digits are blinking and can set by pressing or key e Press MODE again the minute digits are blinking and can be set by pressing or key e Press MODE again the Alarm time is set and s icon will turn on Enable Alarm 1 Alarm 2 e Press ALARM will enable ALARM 1 with icon turns on e Press ALARM again will enable ALARM 2 with 9 icon turns on e Press ALARM again will enable both ALARM 1 and ALARM 2 with 9 and 9 icons to turn on e Press ALARM again will disable both ALARM 1 and ALARM 2 with 9 and 9 icons to turn off Activating the Alarm When the ALARM 1 ALARM 2 is ringing the relative aai icon 9 Q will be flashing Press ALARM key to turn the alarm off e Press button SNOOZE LIGHT alarm stops and the backlight will turn on for 5 seconds with deleted the repeat alarm indicator flashing The alarm sounds again after 4 minutes e Ifthe alarm is not turned off it will stop automatically after 4 minutes Foreign Time Display amp setting Press and hold U
6. play the Dual Time Manual Time Setting The system date and time can be set by pressing MODE for 3 seconds in Time display with the icon turn off e Press MODE one last time the normal time display appears Setting the Time amp Calendar e Press WAVE TIME SET for about 3 seconds the hour digits are blinking and can be set by pressing or key e Press MODE again the minute digits are blinking and can be set by pressing or key e Press MODE again the year digits are blinking and can be set by pressing or key e Press MODE again the month digits are blinking and can be set by pressing or key e Press MODE again the date digits is blinking and can be set by pressing or key Select 12 hour or 24 hour display format e Press will toggle the display format between 12 hour and 24 hour N B 1 If no key is pressed within 30 seconds it will exit the Manual Time Setting Mode and go back to Time Display without the data update 2 During any setting mode press and hold or key for 2 seconds for fast setting Calendar To change the weekday display from one language to another language press key for 3 seconds the display will show the current ees D EN for English GE for German O FR for French I for Italian SP for Spanish Press amp Hold key for 2 seconds will toggle to the other languages Setting the Alarm time ALARM 1 setti
Download Pdf Manuals
Related Search