OWNERS MANUAL WET & DRY VAC
Contents
1. 3 When using machine Do not run machine over cord Do not pull machine by cord or plug Do not pull cord around sharp edges or corners Turn power switch to off prior to unplugging machine Do not unplug by pulling on the cord Do not stretch cord Do not handle plug with wet hands Keep cord away from heated surfaces Do not pick up burning or smoking debris such as cigarettes matches or hot ashes Report machine damage or faulty operation immediately 4 Before leaving or servicing machine Turn off machine Unplug cord from outlet 5 When servicing machine Unplug cord from outlet Use manufacturer supplied or approved replacement parts HANDLE ASSEMBLY HANDLE ASSEMBLY INSTRUCTIONS Figure 3 Attaching Handle 11 Remove handle from ship position and remove upper handle mounting screws from machine Figure 1 2 Realign handle as shown and replace screws amp washers Figure 2 3 Attach rear hose dump clamp Figure 3 4 Attach front mount squeegee Figure 4 Operation of Wet amp Dry Vacuum Read operators manual thoroughly prior to operating or servicing this machine WET PICKUP 11 Remove vacuum head and remove the cloth or paper filter from vacuum install the bubble buster 2 While vacuum head is removed check to make sure that the float shut off is unobstructed and fully functional 3 Replace vacuum head and latch it in place2. 19 VA75020 CLOTH BAG DUST OPTIONAL 41 20 VA75020 1 CLIP CLOTH BAG OPTIONAL 41 21 VA20246 ROLLER 2 13 Wiring Diagram BSL18WD Switch 120V x Blue 60Hz Single White _ 27 White Phase Power Green GIY Suppl Y SJT 16 3C Power Supply Cord 14
3. VA21521 GROMMET POWER CORD 41 15 VA91346 ON OFF SWITCH 41 16 GV15002 MOUNTING COVER MOTOR 41 17 FC25002A MOUNTING PLATE MOTOR 41 18 VA41032 GASKET MOTOR 2 19 2049000 VAC MOTOR 115V 1 20 GV25002 SEAL PLATE 41 21 GV15004A MOUNTING BASE MOTOR 1 22 GV15006 GASKET MOUNTING PLATE 41 23 GV25010 FILTER SCREEN 41 24 GV25013 WATER GUARD 41 25 GV25006 TRUMPET 41 26 GV25003 POLE BALL 41 27 VF14090 RING 1 28 GV25009 BALL 1 29 GV0014 VACUUM FILTER ASSY 41 GV25014 BUBBLE BUSTER 41 PARTS LIST TANK GROUP TR A N A H Ne SAAN TANK GROUP PARTS LIST FOR BSL18WD DIA PART NO No NUMBER DESCRIPTION REQ D 1 VA80857 LOGO LABEL 2 2 75001 TANK 1 3 GT13022 NUT M5 NYLON INSERT 4 4 VF13474A WASHER 6 5 21595 CATCH 2 6 VA14010 SCREW M5 x 20 4 7 14004 SELF TAPPING SCREW ST4 20 4 8 VA13483 WASHER 4 9 VA21514 GASKET 1 10 VA21513A INTAKE 1 11 VA85018 HOSE ASSEMBLY 41 12 91342 3 5 CASTER 2 13 VF13600 WASHER 10 14 VF13495 SCREW 16 6 15 VA75005 LEAF SPRING 1 16 VA75013 AXLE 1 17 VA85003 KNOB 2 18 VA75006 MOUNTING PLATE PICK UP TOOL 41 19 VA75007 BUMPER 2 20 VA85002 BODY PICK UP TOOL 24 1 VA75008 BODY PICK UP TOOL 41 21 VA13471 SELF TAPPING SCREW ST5 x 10 2 20 VA85001 CLAMP BLADE 24
4. 1 75009 CLAMP BLADE 1 23 VV20501 SCREW M5 x 14 PH 6 24 VA85007 BLADE 24 2 VA75010 BLADE 30 2 25 13491 SCREW M8 x 25 2 26 VA85005 LOCK 4 27 VA85004 AXLE WHEEL 2 28 VA91345 8 WHEEL 2 2 29 VF13516 WASHER 8 VA14001 LOCK 4 31 VA75011 AXLE MOUNTING PLATE 1 32 VA75012 PEDAL 1 33 VA75003 AXLE PEDAL 1 34 601135 WASHER 2 35 VA80862 10 WHEEL 2 36 VA80863 CAP AXLE WHEEL 2 37 VA14002 SCREW M10 x 50 6 38 VA75002 HANDLE 1 39 10113 CLAMP 2 1 40 VA93208A DRAIN HOSE 1 41 GV70034 CLAMP DRAIN HOSE 41 42 20104 PLUG DRAIN HOSE 1 11 ACCESSORIES ACCESSORIES PARTS LIST FOR BSL18WD DIA PART NO No NUMBER DESCRIPTION REG D 1 VA20803 DUSTING TOOL 41 2 20248 TUBE 2 3 VA20209 WAND 1 4 Gvoo40 D DRY PICK UP TOOL 41 5 GV0040 W WET PICK UP TOOL 41 6 20207 8 RUBBER BLADES 400mm 2 7 20207 5 SEAT BLADE 400mm 2 8 VA20413 PIN WHEEL 2 9 VA20207 4 SEAT WHEEL 2 10 VA20207 3 CLIP FLOOR TOOL ADAPTER 41 11 VA20207 2 FLOOR TOOL ADAPTER 38mm 41 12 VA20806 CREVICE TOOL 41 13 VA20201 MACHINE END 41 14 VA20202 THREADED INSERT 2 15 VA20203 CLIP RING 2 16 VA20206 ANGLED HOSE END 38mm 41 17 VA20288 HOSE ASSY 41 VA00001 24 FRONT MOUNT SQUEEGEE ASSY 1 18 2 30 FRONT MOUNT SQUEEGEE OPTIONALJASSY 1 5 24 DRY PICK UP TOOL ASSY OPTIONAL 41
5. 4 Connect vacuum hose to inlet on the machine body 5 Attach appropriate accessory tool for the job to be completed 6 Plug power cord into a grounded outlet Do not use an extension cord in conjunction with the standard power cord 7 If using the front mounted squeegee assembly be sure that squeegee is attached to front of machine 8 If using the front mounted squeegee assembly lower squeegee to the floor by depressing the top half of the pedal rear of the machine forward with your foot 9 Turn power switch to on position 10 During wet pickup the float shut off will automatically prevent water from entering the recovery tank once the recovery tank is full If foam develops in the recovery tank during wet vacuuming use de foamer chemical to help eliminate the foam Foam will not activate the float shut off and therefore may cause vacuum motor damage 11 To raise the squeegee assembly back to transport position depress the bottom half of the pedal rear of the machine downward with your foot Be sure that the handle is properly assembled on machine body prior to operating 6 machine The shovelnose wet dry vacuum includes the GV25014 bubble buster blue nylon foam suppression bag This bag must be used in all wet pick up applications Failure to use the bag will void the warranty on the vacuum motor DRY PICKUP 11 Remove vacuum head and bubble buster and be sure the cloth or pap
6. The Smart Way to Clean WET amp DRY VAC OWNERS MANUAL IMPORTANT READ OWNERS MANUAL CAREFULLY Please fill out amp return your warranty card MODEL _ BSL18WD SERIAL REV 01 02 13 www mybrightsolutions com VA80860 The Smart Way to Clean TABLE OF CONTENTS Safety Precautions 4 Handle Assembly 5 Machine Operation 6 Machine Maintenance amp Storage 7 Parts Lists 8 13 Wiring Diagram 14 The Smart Way to Clean SAFETY PRECAUTIONS This machine must be grounded Grounding provides the path of least resistance for electrical current To reduce the risk of electrical shock should the machine malfunction the machine has a special grounding plug Do not remove the ground pin under any circumstances Grounded 210 This machine is intended for commercial use It is constructed for use in an indoor environment and is not intended for any other use Use only recommended accessories All operators shall read understand and exercise the following safety precautions 1 Do not operate machine Unless trained and authorized Unless you have read and understand operators manual In flammable or explosive areas With damaged cord or plug If not in proper operating condition In outdoor areas In standing water Without bag filters in place With the use of extension cords 2 Before operating machine Make sure all safety devices are in place and operate properly
7. after each use Replace bag when it is 3 4 full 4 Clean outside of machine with a mild cleaner 5 Check power cord for any damage lf any 6 Clean squeegee blades with a cloth Do not use your fingers to wipe the blades 7 Check vacuum hose for holes and clogs 8 Lubricate wheels casters and axles with a water resistant lubricant every month 9 Check machine for loose or missing nuts and bolts and replace as necessary After each use in a wet pick up application remove the GV25014 Bubble Buster blue nylon foam suppression bag and rinse it with clean water This will aid in preventing any build up which can reduce air flow STORAGE 1 Unplug machine from power source 2 Store in upright position in a dry area 3 Store with squeegee assembly off the ground 4 Store with vacuum head off unit so that tank may breathe PARTS LIST VACUUM GROUP VACUUM GROUP PARTS LIST FOR BSL18WD DIA PART NO No NUMBER DESCRIPTION REG D 1 GT10004 HANDLE 1 2 VA80861 READ MANUAL LABEL 1 VA80859 SERIAL TAG 41 A VA80858 DECAL WARNING 41 5 GT10003B COVER VAC HEAD 1 6 GT13001 ST5 12 PH 3 7 GT10019 UPPER COVER MOTOR 41 8 GT13004 ST5 x 20 PH 1 9 GT13034 ST5 x 50 PH 4 10 GT13033 ST5 x 44 PH 6 11 VA13470 ST3 x 16 PH 2 12 VA21517 CLAMP BLOCK 1 13 VA65001 CABLE POWER 41 14
8. er filter is properly installed Do not operate machine without bag or filter properly installed 2 Replace vacuum head and latch it in place 3 Connect vacuum hose to inlet on the machine body 4 Attach appropriate accessory tool for the job to be completed 5 Plug power cord into a grounded outlet Do not use an extension cord in conjunction with the standard power cord 6 Turn power switch to on position 7 Check the filter bag periodically to see if it is full For optimal performance replace bag when it is 3 4 full DRAINING THE RECOVERY TANK 1 Unplug machine from power outlet 2 Transport machine to nearest floor drain or bucket 3 Remove drain hose from rear of machine Remove ball plug from drain hose and drain the contents of the tank 4 After the contents have drained remove the vacuum head and rinse recovery tank with clean water 5 Replace the ball plug on the drain hose and hang hose back on the rear of the machine e To prevent odors in the recovery tank remove the vacuum head when machine is not in operation to allow air to circulate MAINTENANCE To keep the machine performing well for many years please follow the following maintenance procedures Always confirm that the machine is unplugged prior to performing any maintenance or repairs 1 Drain and rinse recovery tank after each use 2 Clean float shut off after each use 3 Check bag to see if it is full
Download Pdf Manuals
Related Search