MET ONE-HHPC-2-Particle-Counter-User-Manual
Contents
1. Figure 15 Delete Buffer screen 24 Section 5 Maintenance DANGER Only qualified personnel should conduct the tasks described in this section of the manual MET ONE 5 1 Battery maintenance The battery status light indicates the relative battery charge status described in Table 4 The power supply provided with the instrument serves as battery charger and a direct power source Connect the power supply for continuous and long term sampling Table 4 Battery status indicator Light Charge mode Steady green Fast charge Flashing green Maintenance charging mode Battery is defective and needs to be replaced No light Battery is fully charged To charge the battery 1 Connect the external power supply refer to section 3 3 4 on page 14 2 Turn on the MET ONE HHPC 2 3 Remove the power supply when no light is seen 5 1 1 Charge a drained battery To charge a drained battery 1 Attach the external power supply to the MET ONE HHPC 2 unit 2 Wait for five minutes Turn on the MET ONE HHPC 2 3 Leave the unit attached to the power supply until the battery charging indicator light turns off 5 2 Calibrate the MET ONE HHPC 2 Return the MET ONE HHPC 2 to the manufacturer annually for recalibration to comply with JIS B9921 1989 standards The calibration date is displayed on the manufacturer decal on the back of the MET ONE HHPC 2 Refer to Section 8 on page 31 for MET ONE HHPC 2 return procedures 25 Maintenance 22. non condensing 10 C to 50 C 14 F to 122 F JIS B 9921 1997 Light Scattering Automatic Particle Counter Standards Federal Standard 209E Standard Practice for Defining Size Calibration Resolution and Counting Accuracy of an Air Borne Particle Counter Using Near Monodispersed Spherical Particulate Material Specifications Section 2 General Information 2 1 Safety information Read this entire manual before unpacking setting up or operating this equipment Pay attention to all danger and caution statements Failure to do so could result in serious injury to the operator or damage to the equipment To make sure that the protection provided by this equipment is not impaired do not use or install this equipment in any manner other than that specified in this manual 2 1 1 Use of hazard information DANGER Indicates a potentially or imminently hazardous situation which if not avoided will result in death or serious injury WARNING Indicates a potentially or imminently hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation that can result in minor or moderate injury Important Note Indicates a situation which if not avoided can cause damage to the instrument Information that requires special emphasis Note Information that supplements points in the main text 2 1 2 Precautionary labels Read all labels and tags attached t
3. Belangrijk document Bewaar het bij de productpapieren POLISH Sprzet elektryczny oznaczony takim symbolem nie moze by likwidowany w europejskich systemach utylizacji po dniu 12 sierpnia 2005 Zgodnie z europejskimi lokalnymi i panstwowymi przepisami prawa Dyrektywa Unii Europejskiej 2002 96 EC uzytkownicy sprzetu elektrycznego w Europie musza obecnie przekazywac Producentowi stary sprzet lub sprzet po okresie uzytkowania do bezptatnej utylizacji Uwaga Aby przekazac sprzet do recyklingu nalezy zwr cic siedo producenta lub dostawcy sprzetu w celu uzyskania instrukcji dotyczacych procedur przekazywania do utylizacji sprzetu po okresie uzytkowania Wazny dokument Zachowac z dokumentacja produktu PORTUGESE Qualquer equipamento el ctrico que ostente este s mbolo nao poder ser eliminado atrav s dos sistemas publicos europeus de tratamento de res duos s lidos a partir de 12 de Agosto de 2005 De acordo com as normas locais e europeias Directiva Europeia 2002 96 EC os utilizadores europeus de equipamentos el ctricos dever o agora devolver os seus equipamentos velhos ou em fim de vida ao produtor para o respectivo tratamento sem quaisquer custos para o utilizador Nota No que toca devoluc o para reciclagem por favor contacte o produtor ou fornecedor do equipamento para instru es de devolu o de equipamento em fim de vida para a sua correcta elimina o Documento importante Mantenha junto dos registos do produto Form N
4. the unit and the MET ONE Opening screen displays briefly followed by the Main screen Note If the MET ONE HHPC 2 does not power up double check the AC connection or the battery power To charge the battery refer to section 5 1 on page 25 15 Operation 4 3 1 Keypad Figure 7 shows the display of the Main screen of MET ONE HHPC 2 Table 1 on page 16 provides information about the keypad available at the bottom of the screen and the various function keys Figure MET ONE HHPC 2 Main screen display 3 MODE key 4 START STOP key 1 Display screen 2 POWER key Table 1 Indicators and key features or functions START STOP Starts and stops a sample Selects modes and saves data when the unit is counting POWER Toggles the power on and off 16 4 3 2 Screens Operation Press the corresponding button from the keypad at the bottom of the LCD to invoke the following screens e Main screen The main screen displays e Channel sizes e Particle counts only displayed when counting or in Buffer mode e Status of the counting process Run or Wait e Battery charge indicator amount of charge remaining in the battery refer to Table 4 on page 25 e Select mode screen e Select volume screen e Buffer count and Buffer options screen e Display buffer screen e Contrast screen e Date and Clock setup screen 4 4 Configuration setup Once the MET ONE HHPC 2 is unpacked an
5. time press the MODE key to select the next field Press the START STOP key to change the numbers 6 When the date and time are set press and hold the MODE key for one second to save the new setting and return to the Main screen 4 5 2 Select the count mode To select the count mode 1 Press the MODE key once on the Main screen Refer to Table 2 on page 18 for the different modes available The bottom line displays the current mode refer to Figure 8 on page 18 2 Press the START STOP or the MODE key 3 When the required mode is displayed on the screen press and hold the MODE key for one second to save the new setting and return to the Main screen Select Mode Rate 1 Figure 8 Select mode screen Table 2 Count modes mo Joos mm The Concentration mode is useful for taking a quick snapshot of airborne particulate samples especially in areas where particulate levels are unknown and may exceed the operating Concentration levels of the counter The MET ONE HHPC 2 estimates count Volume size per cubic foot or liter depending on the volume selected The unit updates the results by calculating completed sample counts and volume compared to the balance of volume remaining In the Rate mode counting is continuous The sliding average of l Rate ee Volume unit ten samples is displayed In the Totalize mode number of counts are displayed as they accumulate until the end of the sample When the sample is completed the
6. 6 Section6 Troubleshooting 6 1 Problems and recommendations Table 5 lists the problems reasons and the recommended actions that occur while using MET ONE HHPC 2 Table 5 Troubleshooting procedures Zero count filter or Attach the filter or hose barb hose barb is not properly attached to the unit zero count Internal air leak Contact the customer service center for repair Cell contamination by excessive dust Return the unit to a factory authorized service center exposure MET ONE HHPC 2 does not The MET ONE HHPC 2 does not turn on when the POWER key is pressed The battery voltage too Connect external power supply to MET ONE HHPC 2 for low operation and charging Then turn on the power again Disconnect the power jack from the unit and the power cord Connections to MET from the AC power source wall receptacle Disconnect the MET ONE HHPC 2 unit does not er cord plug from the power supply and reconnect the cord plug to ONE HHPC 2 unit is l charge the power supply firmly Restore all connections to the unit and proper i power source If the problem persists contact the customer service center for repair No records i No records in buffer No records in buffer Make sure there are records in the buffer Communication Make sure that the communication parameters of the computer parameter are not set are set to 9600 baud 8 data bits no parity 1 stop bit The connections are Check the connectio
7. 701230 MET ONE HHPC 2 Handheld Airborne Particle Counter USER MANUAL May 2008 Edition 3 EXCELLENCE IN PROCESS ANALYTICS 701230 MET ONE HHPC 2 Handheld Airborne Particle Counter USER MANUAL May 2008 Edition 3 Hach Ultra Analytics Inc 2008 All rights reserved Printed in the U S A Table of Contents Section SPECHICALONS aa 5 Section 2 General Into Malicia 7 21 Sete AA a ee lee A een 7 21 1 0856 0 N AA NOEN 7 21 2 Precaudra E le T 2 1 3 Electrostatic Discharge ESD considerations nennen 8 2 1 4 Battery safety informatiOM sess nun kenne a ee a e et 8 EE Ee Lee e e gl el EE 9 Section 9 IAStalatiON ee 11 BAER ESTEN RT RT TT 11 3 2 Installation guidelines for MET ONE HHPC 2 2u022202200022000nnnennnne nnn nnne nenn nnne nnns 12 8 3 Mechanleal ns llalohs EG 12 3 3 1 TOSTAIMME ISOKINGHC POE see 12 9 nstallthe inlake hose Dar A 12 3 909 Installithe zero count Tier NG 13 3 3 4 Connect the AC DC power supply nenn nnns 14 Section 4 Ne 15 4 1 Install the MET ONE HHPC 2 utility software 15 42 corte TT T HRRR 15 43 Display laien EE 15 231 KONE 16 252 ee I II NN 17 Reie le UI e ae BEE 17 45 Select CUSTOM SCHINGS EE 17 151 Sene date and ME eee 17 452 Select the COUNE e el 18 4 5 3 Set the sample units and volume soceri annaa aa E a ia 19 RENN 19 4 5 3 2 Concentration or totalize mode 19 4 9 4 SNE ONE 20 40 COUNEr Ope atO
8. EEN 21 4 6 1 Verify the MET ONE HHPC 2 with a zero count filter 21 ee ee une ER 4 8 Transfer the sample data to the PC san nnne nnns 22 29 PANES une ER 410 Storing Samples E 23 4 10 1 Determine the number of sampleS san nnnnnnn 23 4 10 2 Display DUMTEORFECOrOS tii i 23 2105 Clear the DUNGI ocna a a v vs ER UE 24 Section 5 Mamtenance eias teet eM teu cade E iced Les ee 25 5 1 Battery maintenance u due deuda va ad nd done lau denuo nhan ded 25 5411 4 harge a drained Re En EE 25 5 2 Calibrate the MET ONE HIP G32 nn aaa ua au e E ette eue d 25 Section 6 Troubleshooting ond cit met tati nen 27 9 1 Problems and recommendauonsun ET 27 Section 7 Replacement Parts and Accessories conos 29 Pee 29 faz Opona Lee EE 29 Section 8 Service Contact Information 31 Table of Contents Section 9 Limited Warrantv 32 Section 10 COPTIC Atl OM een 33 Appendix A Data Communications usnnnnnnununnnnnnnnnnnrnnrnrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrnn 35 NA 37 Section 1 Specifications Specifications are subject to change without notice Geen 114 30 mm x 209 60 mm x 57 20 mm 4 5 x 8 25 x 2 25 Laser diode index guided 26 000 MTBF at 25 C 5095 at 0 3 um 10095 for particles 0 45 um per JIS B9921 1997 20 to 9096 non condensing 3 C 10 C to 40 C 50 F to 104 F 10 C to 40 C 50 F to 104 F 2096 to 9096
9. HHPC 2 power port refer to Figure 5 item 1 Figure 5 Location of power port 1 I O port 2 Power port 14 Section 4 Operation 4 1 Install the MET ONE HHPC 2 utility software 4 2 Start up To install the MET ONE HHPC 2 utility software 1 Connect the MET ONE HHPC 2 to the communications port on the PC using the RS232 modular cable VP894408 Connect the DB9 to the RJ45 converter SA000070 01 Insert the MET ONE HHPC 2 utility software CSVDownloadUtility diskette into the drive Copy CSVDownloadUtility exe and CSVDownloadUtility ini from the diskette to a working directory on the PC If the communications port to be used is other than Com1 open CSVDownloadUtility ini and change Port Com1 to Port ComX where X represents the number of the port to use To open the utility software double click the CSVDownloadlitility exe file The CSVDownloadUtility window is displayed refer to Figure 6 on page 15 Follow the instructions in the Readme txt file on the diskette to install the software HELDEN LB Figure 6 MET ONE HHPC 2 Utility CSVDownloadUtility window Press and hold the POWER button on the right of the display of the MET ONE HHPC 2 to turn on the unit When the MET ONE HHPC 2 is powered on the MET ONE Opening screen is displayed briefly followed by the Main screen 4 3 Display and keypad The MET ONE HHPC 2 features a Liquid Crystal Display LCD with a keypad at the bottom Power on
10. MENDED BY THE MANUFACTURER DISPOSE OF BATTERIES ACCORDING TO MANUFACTURER S INSTRUCTIONS Figure 1 Battery safety label General Information 2 2 General product information The MET ONE Handheld Airborne Particle Counter 2 HHPC 2 refer to Figure 2 is a portable instrument that measures counts stores and reports airborne particulates The standard MET ONE HHPC 2 holds 100 samples in the memory The data records include date time counts sample labels volume alarm flags temperature and relative humidity The user can download the data to a personal computer PC using the included interface cable and software The internal battery powers up the MET ONE HHPC 2 when mobile or when connected to the AC power adapter Note The AC power adapter provided with the unit is used for extended or stationary sampling The MET ONE HHPC 2 is used e To monitor the air quality in clean rooms e To monitor the air quality in manufacturing processes e To monitor the air quality in pharmaceutical production Q 1 Front view of the MET ONE HHPC 2 2 Backview of the MET ONE HHPC 2 Figure 2 MET ONE HHPC 2 1 Bottom view of the MET ONE HHPC 2 10 Section 3 Installation DANGER Only qualified personnel should conduct the tasks described in this section of the manual 3 1 Unpack the instrument Remove the components from the shipping container and inspect for damage Verify that all the items listed in Figure 3 are included If
11. XCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANT Y HACH ULTRA ANALYTICS AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES EVEN IF HACH ULTRA ANALYTICS OR ITS VENDORS HAS BEEN GIVEN ADVANCED NOTICE OF THE POSSIBILITY OF SUCH DAMAGES 32 Section 10 Certification DECLARATION of CONFORMITY We Hach Ultra Analytics 481 California Avenue Grants Pass OR 97526 declare under sole responsibility that the Model HHPC 2 Part Number 2087003 XX TA100003 XX conforms to Directive 89 336 EEC for Electromagnetic Compatibility and Directive 73 23 EEC for Low Voltage Compliance was demonstrated to the following specifications as listed in the official Journal of the European Communities EN 61326 1998 Class A EN 50081 1 1992 Emissions EN 55011 1991 Class A Radiated EN 55011 1991 Class A Conducted EN 61326 1998 EN 50082 1 1997 Immunity EN 61000 4 2 Electrostatic Discharge EN 61000 4 3 Radiated Immunity Amplitude Modulated EN 61000 4 4 Electrical Fast Transient EN 61000 4 5 Surge Transients EN 61000 4 6 Conducted Immunity EN 61000 4 8 Immunity to Power Frequency Magnetic Fields EN 61000 4 11 Voltage Dips and interrupts EN 61010 1 1993 Amendment 1 amp 2 Safety Requirement for Electrical Equipment for Measurement Control and Laboratory Use EN 60825 1 1993 Safety of Laser Products Equipment Classification Requirements and User s Guide Hach Ultra An
12. al installation The MET ONE HHPC 2 is shipped with two different intake devices e sokinetic probe e Intake hose barb Important Note Do not use a wrench to connect or disconnect the intake nozzle or isokinetic probe Only finger tighten the connection 3 3 1 Install the isokinetic probe The isokinetic probe refer to Figure 4 on page 13 is used to sample ambient air samples The isokinetic probe is pre installed and ready for use as soon as the MET ONE HHPC 2 is unpacked To install the isokinetic probe 1 Attach the isokinetic probe to the intake nozzle on the MET ONE HHPC 2 by turning the isokinetic probe to the right 2 Remove the black plastic cap attached to the isokinetic probe Note Make sure that the cap is attached to the isokinetic probe when the probe is not in use The cap protects the MET ONE HHPC 2 from debris and contamination To sample areas that are difficult to reach connect longer tubing to the isokinetic probe with a hose barb end Note Use a maximum of four feet of high purity or approved tubing only Incorrect size or type of tubing will affect the sample accuracy 3 3 2 Install the intake hose barb The intake hose barb refer to Figure 4 on page 13 is connected to the MET ONE HHPC 2 for zero counting and purging or to sample areas that are difficult to reach To install the intake hose barb 1 Unscrew the isokinetic probe from the MET ONE HHPC 2 2 Attach the hose barb 3 Remove the protective c
13. alytics Shawn Hogan Engineering Manager March 8 2005 Di Place and date of issue Name signature of authorized person 33 Certification 34 Appendix A Data Communications A 1 Remote serial interface I O Port The MET ONE HHPC 2 comes with an RS232 communications port an RS232 cable and an RJ45 connector The RS232 communications port is used to communicate with a computer to download data and for remote operation The specifications and wire pin outs for the I O port are e Baud rate 9600 baud e Data bits 8 bits e Parity None e Stop bits 1 bit A 1 1 DB9 serial connection If the computer or terminal has a 9 pin serial port with a female connector use the modular RJ45 to DB9 connector provided along with the RS232 cable The MET ONE HHPC 2 is configured as a Data Communication Equipment DCE so the use of a null modem cable is not required The cable pin assignments are shown in Figure 17 HHPC 2 RJ 45 Female RS485 B RS485 A SD RD CS ER N C GN D N C Adapter RJ 45 Female oO 0 O oa bh W N AN DB 9 Female oO 0 N O C bh W N PC DB 9 Male N C RX TX DTR GND N C N C DSR N C Figure 17 Pin layout for the RJ45 to DB9 connector cable 35 36 A accessories included sees 29 B EENHEETEN 8 C e Te e NEE 33 conne
14. any items are missing or damaged contact the manufacturer or sales representative Retain the original packaging materials Use the original packaging material to store or ship the instrument to protect against damage during storage or transportation HHPC 2 r 9 UTILITY SOFTWARE lt d Figure 3 List of packaged items 1 MET ONE HHPC 2 6 6 OD high purity tubing VP792002 2 Zerocount filter 7 MET ONE HHPC 2 Utility software CS200025 3 Intake nozzle 1 8 hose barb MP000026 01 8 RS232 modular cable VP894408 4 Black cap Intake nozzle cover 9 RJ45 to DB9 adaptor SA000070 01 5 US power cord CS200025 10 AC DC power supply VP624005 11 Installation 3 2 Installation guidelines for MET ONE HHPC 2 The MET ONE HHPC 2 is ready to use when shipped and has default configuration settings Refer to the following general guidelines during installation 1 Liftthe MET ONE HHPC 2 from the shipping container or the carrying case and place it on a flat surface 2 Remove the layer of protective plastic from the LCD screen 3 Remove the isokinetic probe cover black plastic cap before the startup of the MET ONE HHPC 2 Note The pump and other internal electrical components will be damaged if the cap is left on Note The battery is charged before shipping but may need to be charged before operation refer to section 6 1 on page 27 for more information 3 3 Mechanic
15. ap from the intake hose barb 12 Installation Figure 4 Isokinetic probe with tubing and zero count filter 1 Hose barb fitting 3 Tubing 2 Isokinetic probe 4 MET ONE HHPC 2 3 3 3 Install the zero count filter In a clean room application the zero count filter refer to Figure 3 on page 11 item 2 verifies if the MET ONE HHPC 2 is not counting electrical noise signals from internal components and is not subject to external interference In indoor air quality and other applications the zero count filter cleans out the sensor immediately after a high concentration sampling To connect the zero count filter 1 Remove the isokinetic probe from the MET ONE HHPC 2 2 Attach the intake hose barb MP000026 01 3 Secure the high purity tubing VP792002 to the hose barb 4 Secure the opposite end of the tubing to the zero count filter VP212808 Note Make sure that the arrow of airflow direction or the indicator on the zero count filter points towards the tubing 13 Installation 3 3 4 Connect the AC DC power supply Important Note Do not use a power supply unit that does not supply the required voltage and charging current polarity to operate the MET ONE HHPC 2 To connect the external power supply 1 Turn off power to the MET ONE HHPC 2 unit 2 Plug one end of the power cord into the external power supply and the other end into an electrical wall receptacle 3 Plug the external power supply jack into the MET ONE
16. applicable industry standard s is continued Remove the zero count filter and attach the isokinetic probe to resume normal operations 21 Operation 4 7 Collect samples To collect samples 1 4 Place the MET ONE HHPC 2 unit upright and remove the intake valve cover the black plastic cap from the intake barb or the isokinetic probe Press the POWER key to turn on the unit To review each setting press the MODE key to display the current setting on the bottom line of the Main screen Continue to press the MODE key until all the settings are reviewed Press the START STOP key to start sampling on the Main screen 4 8 Transfer the sample data to the PC Refer to section 3 on page 14 to install the MET ONE HHPC 2 Utility software 4 9 Print samples 22 To transfer sample data from MET ONE HHPC 2 to a PC 1 3 Use the MET ONE HHPC 2 Utility software to download particle count data to aPC in comma separated variable CSV file format The particle count data can be viewed in Microsoft Excel and other spreadsheet software applications All parameters required by the download utility are stored in the initialization file that is also on the diskette Double click the CSV Download Utility exe to start the application Print samples at the end of each run or print each sample as it is taken Note Not all printers are compatible with the MET ONE HHPC 2 Make sure that the portable printer is configured c
17. cement Parts and Accessories 30 Section 8 Service Contact Information U S A customers By Telephone 541 472 6500 6 30 a m to 5 00 p m PST Monday through Friday By Fax 541 474 7414 By Mail Hach Ultra 481 California Avenue Grants Pass Oregon 97526 Email TechSupportGP hachultra com Website www hachultra com International customers By Telephone 41 22 594 64 00 By Fax 41 22 594 64 99 By Mail Hach Ultra Service Department 6 route de Compois C P 212 CH 1222 Vesenaz Geneva Switzerland Website www hachultra com Information required e Your name e Your phone number e Your company name e Your fax number e Model number e Serial number e Comment or question 31 Section 9 Limited Warranty Hach Ultra warrants this instrument to be free of defects in materials and workmanship for a period of one year from the shipping date If any instrument covered under this warranty proves defective during this period Hach Ultra will at its option either repair the defective part without charge for extra parts and labor or provide an equivalent replacement in exchange for the defective product If any diode covered under this warranty proves defective during this period Hach Ultra will at its option either repair the defective diode without charge for parts and labor or provide an equivalent replacement in exchange for the defective product To obtain service under this warranty the cus
18. ctions adjustments 12 15 D Data Communication Equipment DCE 35 DB9 serial connection nnm 35 H hazard IDformiatlOD ae T lose DAN Are 12 l SOKNET PONG an ee 12 P procedures troubleshooting 27 R Replacement Parts NNN 29 RIAS COMMCGCION dM 35 S Safety information 7 specifications environment eene 5 specifications general rrurrrnnnnnnrnnaneranennnrnnernnannnnne 5 U Unpack instrument aaa 11 Z zero count filter ooocooccconcocnnoniocnnoninanicanons 13 37 Electrical equipment marked with this symbol may not be disposed of in European public disposal systems after 12 August of 2005 In conformity with European local and national regulations EU Directive 2002 96 EC European electrical equipment users must now return old or end of life equipment to the Producer for disposal at no charge to the user Note For return for recycling please contact the equipment producer or supplier for instructions on how to return end of life equipment for proper disposal Important document Retain with product records GERMAN Elektroger te die mit diesem Symbol gekennzeichnet sind d rfen in Europa nach dem 12 August 2005 nicht mehr ber die ffentliche Abfallentsorgung entsorgt werden In bereinstimmung mit lokalen und nationalen europ ischen Bestimmungen EU Richtlinie 2002 96 EC m ss
19. d connected to the appropriate intake device use the default settings to conduct a 1 minute count cycle Download the data to a PC and print the results To perform a 1 minute count cycle 1 Remove the isokinetic probe cover black plastic cap 2 Press and hold the POWER key until the MET ONE HHPC 2 sounds two beeps and turns on 3 Press START STOP on the Main screen to start counting The count cycle begins and the bottom line of display changes from Wait to Run After one minute the count cycle ends and the display clears Note The results are saved automatically in the print buffer Refer to section 4 8 on page 22 to transfer the data to a PC and print the results 4 5 Select custom settings To choose a setting select an option that is displayed at the bottom of the Main screen when the MODE key is pressed then use the START STOP and MODE keys to scroll through the options or save selections 4 5 1 Set the date and time To set the date and time 1 Press the MODE key six times on the Main screen The bottom line displays the time and date 2 Press and hold the MODE key for one second until two beeps are heard The Date and Time screen is displayed with the date selected 3 Use the MODE key to select the digit The cursor moves to the next digit 17 Operation 4 When the date month year or time is set press the START STOP key to change the numbers for that field 5 Toselect another unit of
20. e current volume setting Press and hold the MODE key for one second until two beeps are heard The Select Volume screen displays the selected volume as shown in Figure 10 on page 20 To review the sample volume settings available press either the START STOP key or the MODE key Refer to Table 3 for sample volume choices 19 Operation Table 3 Sample volume settings Volume Time for sample MM SS 5 Once the required volume choice is displayed press and hold the MODE key for one second to save the new setting and return to the Main screen The volume selected is displayed in the right column of the Main screen Zum D Elm Figure 10 Select volume screen 4 5 4 Set the contrast To set the contrast 1 Press the MODE key five times on the Main screen 2 he bottom line displays the current contrast 3 Press and hold the MODE key for one second until two beeps are heard The Program Contrast screen is displayed refer to Figure 11 4 Press the START STOP key to increase the contrast Press and hold the MODE key to decrease the contrast 5 Once the required contrast is achieved press and hold the MODE key for one second to save the new setting and return to the Main screen 20 Operation Prog Contrast Figure 11 Program contrast screen 4 6 Counter operation Once the MET ONE HHPC 2 unit configuration is set Use the zero count to verify the operation of the filter Collect air samples tra
21. en Benutzer von Elektroger ten in Europa ab diesem Zeitpunkt alte bzw zu verschrottende Ger te zur Entsorgung kostenfrei an den Hersteller zur ckgeben Hinweis Bitte wenden Sie sich an den Hersteller bzw an den H ndler von dem Sie das Ger t bezogen haben um Informationen zur R ckgabe des Altger ts zur ordnungsgem en Entsorgung zu erhalten Wichtige Informationen Bitte zusammen mit den Produktinformationen aufbewahren FRENCH A partir du 12 ao t 2005 il est interdit de mettre au rebut le mat riel lectrique marqu de ce symbole par les voies habituelles de d chetterie publique Conform ment la r glementation europ enne directive UE 2002 96 EC les utilisateurs de mat riel lectrique en Europe doivent d sormais retourner le mat riel us ou p rim au fabricant pour limination sans frais pour l utilisateur Remarque Veuillez vous adresser au fabricant ou au fournisseur du mat riel pour les instructions de retour du mat riel us ou p rim aux fins d limination conforme Ce document est important Conservez le dans le dossier du produit ITALIAN Le apparecchiature elettriche con apposto questo simbolo non possono essere smaltite nelle discariche pubbliche europee successivamente al 12 agosto 2005 In conformit alle normative europee locali e nazionali Direttiva UE 2002 96 EC gli utilizzatori europei di apparecchiature elettriche devono restituire al produttore le apparecchiature vecchie o a fine vita per lo s
22. f rs ljaren f r att fa anvisningar om hur du terl mnar kasserad utrustning f r att den ska bortskaffas pa r tt s tt Viktigt dokument Spara tillsammans med dina produktbeskrivningar SPANISH A partir del 12 de agosto de 2005 los equipos el ctricos que lleven este s mbolo no deber n ser desechados en los puntos limpios europeos De conformidad con las normativas europeas locales y nacionales Directiva de la UE 2002 96 EC a partir de esa fecha los usuarios europeos de equipos el ctricos deber n devolver los equipos usados u obsoletos al fabricante de los mismos para su reciclado sin coste alguno para el usuario Nota S rvase ponerse en contacto con el fabricante o proveedor de los equipos para solicitar instrucciones sobre c mo devolver los equipos obsoletos para su correcto reciclado Documento importante Guardar junto con los registros de los equipos DUTCH Elektrische apparatuur die is voorzien van dit symbool mag na 12 augustus 2005 niet meer worden afgevoerd naar Europese openbare afvalsystemen Conform Europese lokale en nationale wetgegeving EU richtlijn 2002 96 EC dienen gebruikers van elektrische apparaten voortaan hun oude of afgedankte apparatuur kosteloos voor recycling of vernietiging naar de producent terug te brengen Nota Als u apparatuur voor recycling terugbrengt moet u contact opnemen met de producent of leverancier voor instructies voor het terugbrengen van de afgedankte apparatuur voor een juiste verwerking
23. lay the buffer records 1 2 Press the MODE key four times on the Main screen Press and hold the MODE key for one second until two beeps are heard The most recent record in the buffer is displayed refer to Figure 13 To review the buffer records press either the MODE key or the START STOP key e MODE key displays the first record e START STOP key scrolls backwards through the records from the most recent to the oldest record Press and hold the MODE key for one second to exit the Stored Buffer Record screen and return to the Main screen D Zum 6524 O Sum 570 Sts 0K V 0 10 Cr BAK NXT 13 19 50 Figure 13 Stored buffer record screen 23 Operation 4 10 3 Clear the buffer To clear the buffer 1 Press the MODE key three times on the Main screen The bottom line displays the number of records in the Buff Count field refer to Figure 14 2 Press and hold the MODE key for one second until two beeps are heard The Buffer count will be displayed on the Buffer Options screen 3 Press the START STOP key to delete the buffer records The Delete Buffer screen is displayed refer to Figure 15 on page 24 4 Press the START STOP key to confirm the deletion The Main screen displays with the buffer count shown at the bottom line Note The buffer count should be equal to zero Buff Count 4 Buffer options DEL SEND Figure 14 Buffer options screen Delete Buffer YES NO
24. maltimento senza alcun costo a carico dell utilizzatore Nota Per conoscere le modalit di restituzione delle apparecchiature a fine vita da riciclare contattare il produttore o il fornitore dell apparecchiatura per un corretto smaltimento Documento importante Conservare con la documentazione del prodotto DANISH Elektriske apparater der er maerket med dette symbol ma ikke bortskaffes i europ iske offentlige affaldssystemer efter den 12 august 2005 I henhold til europ iske lokale og nationale regler EU direktiv 2002 96 EF skal europ iske brugere af elektriske apparater nu returnere gamle eller udtjente apparater til producenten med henblik p bortskaffelse uden omkostninger for brugeren Bem rk I forbindelse med returnering til genbrug skal du kontakte producenten eller leverand ren af apparatet for at f instruktioner om hvordan udtjente apparater bortskaffes korrekt Vigtigt dokument Opbevares sammen med produktdokumenterne Form No 011229 SWEDISH Elektronikutrustning som ar markt med denna symbol kanske inte kan lamnas in pa europeiska offentliga sopstationer efter 2005 08 12 Enligt europeiska lokala och nationella f reskrifter EU direktiv 2002 96 EC m ste anv ndare av elektronikutrustning i Europa nu terl mna gammal eller utrangerad utrustning till tillverkaren f r kassering utan kostnad for anv ndaren Obs Om du ska terl mna utrustning f r tervinning ska du kontakta tillverkaren av utrustningen eller ter
25. ns between the MET ONE HHPC 2 and not proper the computer No records in buffer Make sure that there are records in the buffer Communication Make sure that the communication parameters of the printer are Unable to print data in the buffer parameter are not set set to 9600 baud 8 data bits no parity 1 stop bit The connections are Make sure that the connections between the MET ONE not proper HHPC 2 and the printer Connect the zero count filter and program the MET ONE MET ONE HHPC 2 display The cell is HHPC 2 to run for at least five minutes shows the message CAL ALM contaminated If the problem persists contact the customer service center for repair Unable to download data in the buffer 27 Troubleshooting 28 Section 7__Replacement Parts and Accessories 7 1 Accessories Description Quantity Catalog no Intake nozzle 1 8 hose barb 1 MP000026 01 AC DC power supply 1 VP624005 US power cord 1 VP23501 RJ45 to DB9 adapter 1 SA000070 01 RS232 modular cable 1 VP894408 MET ONE HHPC 2 Utility software 1 CS00025 674 high purity tubing 1 VP792002 7 2 Optional accessories Figure 16 Optional accessories 1 Carrying case SA000089 01 2 Vinyl carrying case SA000249 01 3 RS232serial interface extension cable EP096010 4 5 6 Isokinetic probe hose barb MP000120 01 Serial thermal printer SA000094 01 European power cord VP625300 Repla
26. nsfer them to a computer for further analysis and print them Review the number of samples in the print buffer and if needed clear the print buffer 4 6 1 Verify the MET ONE HHPC 2 with a zero count filter Make sure that the instrument is not falsely counting due to sensor leakage internal or external electrical interference or any other reason before the unit is used for monitoring or verifying clean room condition Clean the MET ONE HHPC 2 using the zero count filter before storage or shipment Purge the MET ONE HHPC 2 with a zero count filter before using it in a clean room or a clean manufacturing environment This process meets the Japanese Industrial Standard B9221 1997 JIS To verify the unit with a zero count filter 1 a 9 D Remove the isokinetic probe from the unit Attach the intake hose barb MP000026 01 Secure the high purity tubing VP 792002 to the hose barb Secure the opposite end of the tubing to the zero count filter VP212808 Make sure the arrow on the filter is pointing away from the tubing Now the unit is ready to purge and zero count Operate the unit for approximately 15 minutes Verify that the data on the display is e Not more than one particle greater than 0 3 um in five minutes on average or e Not more than one particle per 0 5 cubic foot Note Initial counts are typically from particles shedding from components used for zero counting The zero count process or guidelines set forth by
27. o 011229 Dieses Informationsblatt enth lt Angaben die ausschlie lich f r den Export dieses Ger tes in die Volksrepublik China erforderlich sind This document contains information which is only required for the export of this instrument into the People s Republic of China Ce document contient les informations n cessaires pour l exportation d instruments vers la R publique Populaire de Chine AFUMRASHOS ARNE Zen ES RS Ss Optical Particle Counter with Display EE NU LE E KEY Z Cd Cr6 SEE RS 3 X O Hal ERAN PCBA A A7 Wire Conn IL F350 fF Optical Comps IN HE Glass Fuses An E Display O XT ASAS E AMARA HIRES SJ T11363 2006 EMRSZKRUT X T ABAEN EVE TFR MAA E En SJ T11363 2006 E F REER ZHE2B ARE TEW BRIE She Di GE HE m 7 ER tL REAHRA HT aa PAT ERATE LE Pro m l ARAH 3 REDS SRST REAR 5l Form 011360 EUROPE HACH LANGE HACH LANGE GMBH Willst tterstra e 11 40549 D sseldorf Germany Phone 49 0 211 5288 143 info hach lange de USA AND REST OF WORLD Hach Company P O Box 389 Loveland Colorado 80539 0389 USA Phone 800 227 4224 Fax 970 669 2932 techhelp hach com Trademarks are property of their respective owners Specifications subject to change without notice
28. o the instrument Personal injury or damage to the instrument could occur if not observed A symbol if noted on the instrument will be included with a danger or caution statement in the manual This symbol if noted on the instrument references the instruction manual for operation and or safety information Electrical equipment marked with this symbol cannot be disposed of in European public disposal systems after 12 August of 2005 In conformity with European local and national regulations EU Directive 2002 96 EC European electrical equipment users must now return old or end of life equipment to the Producer for disposal at no charge to the user Note To return for recycling contact the equipment producer or supplier for instructions on how to return end of life equipment producer supplied electrical accessories and all auxiliary items for proper disposal This symbol when noted on a product enclosure or barrier indicates that a risk of electrical shock and or electrocution exists This symbol if noted on the product indicates the need for protective eye wear This symbol when noted on the product identifies the location of a fuse or current limiting device This symbol indicates a laser device is used in the equipment This symbol when noted on the product indicated the presence of devices sensitive to Electro static Discharge Pelor Xp ESD and indicated that care must be taken to prevent damage with the e
29. orrectly to function with the MET ONE HHPC 2 To print the downloaded data from the PC 1 Connect the MET ONE HHPC 2 to a serial printer using the RS232 cable Catalog No VP894408 and the DB9 to the RJ45 convertor Catalog No SA000091 01 supplied with the printer Catalog No SA000094 01 Press MODE three times on the Main screen of the particle counter The bottom line displays the number of records in the buffer Press and hold the MODE key for one second until two beeps are heard The Buffer Options screen displays the buffer count To download the buffer records press the MODE key The second Buffer Options screen displays the download options Select one of the following options e MODE key prints formatted data e START STOP key prints unformatted data The Print Buffer screen is displayed Press START STOP to print the records The data from the sample run is printed Operation 4 10 Storing samples The MET ONE HHPC 2 stores each measurement in a 100 record rotating buffer Data is stored in a first in first out order Thus when record 101 is saved the first record is automatically deleted leaving a total of 100 records 4 10 1 Determine the number of samples Press the MODE key three times on the Main screen The bottom line displays the number of records in the Buff Count field refer to Figure 12 O Jum E524 O Sum Figure 12 Buffer count screen 4 10 2 Display buffer records To disp
30. quipment General Information 2 1 3 y Electrostatic Discharge ESD considerations Important Note To minimize hazards and ESD risks maintenance procedures not requiring power to the analyzer should be performed with power removed Delicate internal electronic components can be damaged by static electricity resulting in degraded instrument performance or eventual failure The manufacturer recommends taking the following steps to prevent ESD damage to the instrument e Before touching any instrument electronic components such as printed circuit cards and the components on them discharge static electricity This can be accomplished by touching an earth grounded metal surface such as the chassis of an instrument or a metal conduit or pipe e To reduce static build up avoid excessive movement Transport static sensitive components in anti static containers or packaging e To discharge static electricity from the body and keep it discharged wear a wrist strap connected by a wire to earth ground Handle all static sensitive components in a static safe area If possible use anti static floor pads and work bench pads 2 1 4 Battery safety information WARNING An explosion can occur if the internal battery is replaced incorrectly Figure 1 shows the label that is displayed on the battery for the safety of the user WARNING DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOM
31. record is stored and the value is displayed on the screen until the next sample is started Totalize Volume size 18 Operation 4 5 3 Setthe sample units and volume Sample volume may be measured in either liters or cubic feet The volume size can range from 0 01 cubic foot or 1 liter up to 1 cubic foot or 28 3 liters 4 5 3 1 Rate mode In the Rate mode the unit of the sample volume is selected To select the unit of sample volume 1 2 Make sure the unit is set to Rate mode as described in section 4 5 2 on page 18 Press the MODE key twice on the Main screen The bottom line displays the current unit settings as shown in Figure 9 Press and hold the MODE key for one second until two beeps are heard The Select Units screen displays the selected units To select the units press either the START STOP key for cubic feet or the MODE key for liters Press and hold the MODE key for one second to save the new setting and return to the Main screen The units selected appear on the right column of the Main screen Select Units Units Figure 9 Select Units screen 4 5 3 2 Concentration or totalize mode In the Totalize or Concentration modes the volume size is selected To select the volume size in concentration or totalize mode 1 Make sure the unit is set to Concentration or Totalize mode as described in section 4 5 2 on page 18 Press the MODE key twice on the Main screen The bottom line displays th
32. tomer must notify the nearest Hach Ultra service support center on or before the expiration of the warranty period and follow their instructions for return of the defective instrument The customer is responsible for all costs associated with packaging and transporting the defective unit to the service support center and must prepay all shipping charges Hach Ultra will pay for return shipping if the shipment is to a location within the same country as the service support center This warranty shall not apply to any defect failure or damage caused by improper use or maintenance or by inadequate maintenance or care This warranty shall not apply to damage resulting from attempts by personnel other than Hach Ultra representatives or factory authorized and trained personnel to install repair or service the instrument to damage resulting from improper use or connection to incompatible equipment or to instruments that have been modified or integrated with other products when the effect of such modification or integration materially increases the time or difficulty of servicing the instrument THIS WARRANTY IS GIVEN BY HACH ULTRA ANALYTICS WITH RESPECT TO THIS INSTRUMENT IN LIEU OF ANY OTHER WARRANTIES EXPRESSED OR IMPLIED HACH ULTRA ANALYTICS AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR NON CONTRACTUAL PURPOSE HACH ULTRA ANALYTICS RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND E
Download Pdf Manuals
Related Search