Conforming Meter List Application
Contents
1. jeso Conforming Meter List Application Independent Electricity System Operator EMmail the completed form including all supporting documents and materials to Jadependeni Hleskioipy Syulera Ooerako Station A Bex 4474 a Ferente ON MSW485 Metering Installations ieso ca Attn Metering InstaHatiensConforming Meter List Application Courier the completed toni wiclichic al sepporiing cocutienk ane materia to 655 Bay Street Suite 10 Pope ON Mets IKA All information submitted in this process will be used by the JESO solely in support of its obligations under the Electricity Act 1998 the Ontario Energy Board Act 1998 the Market Rules and associated policies standards and procedures and its licence All submitted information will be assigned the appropriate confidentiality level upon receipt Terms and acronyms used in this Form that are italicized have the meanings ascribed thereto in Chapter 11 of the Market Rules Jeg ne your package pleaseaHow5Sbusiness days fordeliverytothe4ESO Questions regarding the application form should be directed at email Metering Installations ieso ca or the IESO Customer Relations number 905 403 6900 1 888 448 7777 The Independent Electricity System Operator IESO requires all revenue meters to conform to the standards in the Wholesale Revenue Metering Standard Hardware The JESO publishes a list of conforming meters on its web site www2. Mailing Address E mail Address Secondary Contact Name Position Telephone No Fax No E mail Address Meter Manufacturer Model Serial Number of Meter Requesting Main Meter Conformance _ Requesting Alternate Meter Conformance _ Please note that a main meter automatically qualifies as an alternate meter Suitable for Generator Loads L Suitable for Pure Consumption Loads E Please note that a generator load meter automatically qualifies as a pure consumption load meter Dynamic Bench Test Procedure Please provide the preferred week to perform the Dynamic Bench test Allow at least two weeks to process this request I request the week of Page 2 of 10 Confidential IMO FORM 1179 v5 1 REV 15 06 PART B MAIN AND ALTERNATE METER REQUIREMENTS Use Part B of the application to verify that the meter meets each JESO requirement listed for main or alternate meters Check Yes if the meter does meet the requirement or No if the meter does not meet the requirement If No is selected explain why in the Comments column Applicants should review both checklists to confirm that the appropriate meter category Main or Alternate has been selected for this application Main Meter 1 Measurement Canada Approval Number provide number ne B zZ Comments Firmware Version Number provide number ANSI C12 20 0 2 Speci
3. for 10 minutes registers 10 Reset time Set up meter to be effectively Attempt to reset time using each Measurement Canada sealed Supply read password Note results only read plus synchronize time and read plus write passwords 7 Assumes A phase powers meter electronics If B phase powers meter electronics then disconnect one of A or C phases If C phase powers meter electronics disconnect one of A or B phases Does not matter which phase is disconnected if meter supplied at auxiliary power terminals 8 g F Substitute B or C for A if B or C powers meter electronics IMO FORM 1179 v5 1 REV 15 06 Confidential Page 9 of 10 Part Task Applicant IESO 11 Password Access meter with valid and Security invalid versions of each password in Part 10 Note results 12 Communicate Set up master and slave meters for remote Interrogate slave meter channels with slave interrogation and registers meter PART E ATTACHMENTS LIST FOR ATTACHED DOCUMENTS DISKS OR CDs PART F CERTIFICATION By signing below you confirm that all information provided in this application is correct and is signed by an officer of your organization usually the Primary Contact with signing authority for agreements and contracts Name Please Print Signature Page 10 of 10 Confidential IMO FORM 1179 v5 1 REV
4. 15 06
5. MO FORM 1179 v5 1 REV 15 06 C 3 DIAL UP CONFIGURATIONS Provide a description with diagrams attach additional pages if necessary of dial up configurations supported for multiple meter connections i e master slave multi drop line router If these descriptions and diagrams are already available in the meter s technical or user manual provide page references below Description Reference Manual pg no IMO FORM 1179 v5 1 REV 15 06 Confidential Page 7 of 10 C 4 POWER SOURCE CONFIGURATIONS If submitting an alternate meter in this application or a main meter which can be installed as an alternate describe how the meter meets the Self Power requirement specified in Section 5 4 of the Wholesale Revenue Metering Standard Hardware If these descriptions and diagrams are already available in the meter s technical or user manual provide page references below Reference Manual pg no Page 8 of 10 Confidential IMO FORM 1179 v5 1 REV 15 06 PART D FORMAT OF THE DYNAMIC BENCH TEST This part provides a sample format for the Dynamic Bench Test which the JESO conducts in conjunction with the applicant after this application and all supporting documents have been received and deemed satisfactory by the JESO Applicants should refer to the JESO procedure Conformance Monitoring Conforming Meter List for more information on the Dynamic Ben
6. ch Test Applicants must indicate a preferred testing time for the Dynamic Bench Test in Part A of this application Part Task Applicant IESO 1 Set up load Install a 3 element meter on the test bench Interrogate meter channels and Connect telephone line to the meter registers Apply 120 volts 2 5 Amps at 0 5 Power Factor Run meter at load for minimum of 31 minutes 2 Remove one Disconnect one of B phase voltage or Interrogate meter channels and potential C phase voltage for 10 minutes registers 3 Remove all Disconnect A phase voltage and Interrogate meter channels and potentials remaining voltage phase for 10 minutes registers 4 Reconnect all Reconnect A B and C phase Interrogate meter channels and potentials voltages registers 5 Remove one Disconnect one of A or B or C Interrogate meter channels and current phase currents for 10 minutes registers 6 Remove all Disconnect remaining two phase currents Interrogate meter channels and currents for 10 minutes registers 7 Reconnect all Reconnect A B and C phase Interrogate meter channels and currents currents registers 8 Reverse all Reverse A B and C phase currents Interrogate meter channels and currents for 10 minutes registers 9 Remove one Disconnect one of A or B or C Interrogate meter channels and current phase currents
7. er Yes No Comments Bolded words indicate that requirement differs from main meter requirement Do not complete this page if Main Meter checklist opposite has been used 1 Measurement Canada Approval Number provide number Firmware Version Number provide number ANSI C12 20 0 5 Specification submit test results 4 4 Channel Wh DEL amp REC and VARh DEL amp REC Interval Data 5 Encoded Cumulative Registers all Watts amp VARS 5 Minute Interval Channels 6 7 10 Days of Data Storage 8 10 Days of Battery Back up 9 Alarm Flags 10 Two Passwords minimum 11 Minimum 7 Alphanumeric Char for Device ID 12 Time Clock Resettable by MVY 99MDAS 13 Compatible with UTS M4 98MDAS Software 14 Maintain Eastern Standard Time 15 Modem 2400 BAUD external modem acceptable 16 ANSI Optical Port OO JOJOJOJOJO OJO O 0O 0 oO OO oO OO OOOO OOOO 8 oO OO 0O A Optional Distributed Network Protocol DNP 3 0 compatibility ERRE B Does the Meter support Multi drop or Master Slave configuration O O If Yes complete Part C 3 4 Test results require a signature of a professional engineer An in house engineer is acceptable DELivered and RECeived from the JESO controlled grid in the case of generators or parallel transformers DNP compatibility is not an JESO requirement for revenue metering but a
8. fication submit test results 4 4 Channel Wh DEL amp REC and VARh DEL amp REC Interval Data 5 Encoded Cumulative Registers all Watts amp VARS 6 Ph per Phase Channel 7 V h per Phase Channel 8 5 Minute Interval Channels 9 35 Days of Data Storage 10 35 Days of Battery Back up 11 100 Event Log 12 Two Passwords minimum 13 Minimum 7 Alphanumeric Char for Device ID 14 Time Clock Resettable by MY 99MDAS 15 Compatible with UTS MY 9O0MDAS Software 16 Maintain Eastern Standard Time 17 Modem 9600 BAUD external modem acceptable 18 ANSI Optical Port OhOJOOOOOOUOAOOOO oO oy 0 O Oh OJOUOOUOOUOAOUOOUO oO 0i Oyo O A Optional Distributed Network Protocol DNP 3 0 compatibility OU B Does the Meter support Multi drop or Master Slave configuration 0O O If Yes complete Part C 3 Test results require a signature of a professional engineer An in house engineer is acceptable DELivered and RECeived from the JESO controlled grid in the case of generators or parallel transformers gt DNP compatibility is not an JESO requirement for revenue metering but an optional feature If the meter does have DNP compatibility the JESO will request a sample meter for SCADA testing at a later date IMO FORM 1179 v5 1 Confidential Page 3 of 10 REV 15 06 PART B MAIN AND ALTERNATE METER REQUIREMENTS CONTINUED Alternate Met
9. ieso ca called the Conforming Meter List This list is accessible to all participants in the marketplace Applicants should review the JESO procedure Conformance Monitoring Conforming Meter List before completing this application form This procedure can be downloaded from the JESO web site Applicants are required to complete Parts A B C and F of this form Use Part A to complete general information about your organization and the meter being submitted for conformance acceptance Use Part B to identify if specific features of the meter meet IESO standards Use Part C to provide information required by the JESO to communicate with the meter and to provide information about dial up and power source configurations Part C also contains channel assignment guidelines for the meter which the Applicant is required to follow IMO FORM 1179 v5 1 Confidential Page 1 of 10 REV 15 06 Part D is for reference only and describes the format of the Dynamic Bench Test This test is conducted after this application and all supporting documents have been reviewed and accepted by the JESO at a test site chosen by the applicant Applicants are required to submit one form per manufacturer meter and model Please include with the application any user guides or technical specification documents available for the meter PART A APPLICANT INFORMATION Organization Name Primary Contact Name Position Telephone No Fax No
10. n optional feature If the meter does have DNP compatibility the JESO will request a sample meter for SCADA testing at a later date Page 4 of 10 Confidential IMO FORM 1179 v5 1 REV 15 06 PART C Part C 1 Channel Assignment describes the JESO meter channel assignments All revenue meters operating in the JESO administered markets are recommended to adhere to these channel guidelines Applicants must complete Part C 2 MY 99MDAS Parameters to allow the JESO to communicate with the meter during the Dynamic Bench Test with the M4 90MDAS application Complete parts C 3 and C 4 if applicable C 1 CHANNEL ASSIGNMENT GUIDELINES Interval Data Normal Channel Watts delivered by the JESO grid 1 VARs delivered by the JESO grid 2 Watts received by the JESO grid 3 VARs received by the JESO grid 4 V per phase main meter T per phase main meter C 2 MV 9OMDAS PARAMETERS 1 Indicate the value or setting for each of the M4 9Q0MDAS parameters below 2 Provide export M 990MDAS Master File on disk with this application form a S Ca a ee a a S C p pose O C IMO FORM 1179 v5 1 Confidential Page 5 of 10 REV 15 06 Channels 10 9 Unit of measure for each channel 10 Meter Multiplier for each channel 1 Pulse Multiplier for each channel 0 1 12 each channel 13 Start Meter Reading for each channel 14 Encoder Type for each channel Page 6 of 10 Confidential I
Download Pdf Manuals
Related Search