SYSCONTROL RM 52
Contents
1. FOLLOW ME Display on some models Displayed when FOLLOW ME function is activated Temp Timer display Displays the temperature setting 17 30 When you set the operating mode to FAN no temperature setting is displayed And if in the TIMER mode shows the ON and OFF settings of the TIMER Fan speed display Displays the selected fan speed AUTO no display and three fan speed levels 8 2 LOW S 2235 The fan speed is AUTO when the operating mode is either AUTO or DRY Note All indicators shown in the figure are for the purpose of clear presentation But during the actual operation only the relative functional signs are shown on the display window SLEEP FRESH FAN SLEEP FRESH TIMER OF SWING DIRECT How to use the buttons 1 Auto operation Ensure the unit is plugged inand poweris available The OPERATION indicator onthe display panel of the indoor unit starts flashing 1 Press the MODE button to select Auto 2 Press the UP DOWN button toset the desired temperature The temperature can be set within a range of 17 C 30 C in 1 C increments Press the ON OFF button to start the air conditioner NOTE In the Auto mode the air conditioner can logically choose the mode of Cooling Fan and Heating by sensing the difference between the actual ambient room temperature and the setting temperature on the remote controller In the Auto mode you can not switch th2. Button Used to change the louver movement and set the desired up down air flow direction The louver changes 6 in angle for each press NOTE On some models operate swing feature instead of this feature SWING Button Used to stop or start horizontal louver auto swing feature NOTE On some models used to stop or start vertical louver auto swing featrue FOLLOW ME Button Push this button to initiate the Follow Me feature the remote display is actual temperature at its location The remote control will send this signal to the air conditioner every 3 minutes interval until press the Follow Me button again The air conditioner will cancel the Follow Me feature automatically if it does not receive the signal during any 7 minutes interval Q B Indicators on LCD Mode display Displays the current operation mode Including auto cool 9 dry heat e Not applicable to cooling only models fan J and back to auto Transmission Indicator This transmission indicator lights when remote controller transmits signals to the indoor unit ONIOFF display Displayed by pressing the ON OFF button Press the ON OFF button again to remove TIMER ON display Displayed when TIMER ON time is set TIMER OFF display Displayed when TIMER OFF time is set Sleep Display Displayed under sleeping operation Press the SLEEP button again to remove HEAT see E LU H FAN J 4 Bnn mun nunn Geen Gee NENNEN
3. R OFF button the last setting of stopping operation time and the signal H will show on the display area 2 Press the TIMER OFF button to display 10H on the TIMER OFF display of the remote controller AGO on Operetion 3 Wait for 3 seconds and the digital display area The TIMER ON feature is useful when you want bl enw we A again ue er the unit to turn on automatically before you return OFF nglegtor Temang On and US LUNGUN 1s Set 10 hours later home The air conditioner will automatically start activated operating at the set time Start COMBINED TIMER Setting both ON and OFF timers simultaneously Example TIMER OFF TIMER ON Set 6 hours later To start the air conditioner in 6 hours On gt Stop gt Start operation This feature is useful when you want to stop the air conditioner after you go to bed and start it again in 1 Press the TIMER ON button the last setting of starting operation time and the signal H will show on the display area Ba the morning when you wake up or when you return 2 Press the TIMER ON button to display 6 0H home on he MER ON display of the remote Si Example er P EE one ima To stop the air conditioner 2 hours after setting and e VA TOTA eee ME Oa ae AY On Ies start it again 10 hours after setting area will show the temperature again The Se O ae 1 ete TIMER OFF button f TIMER ON indicator remains on and this ee 2 Press the TIMER OFF button again to display functio
4. SYSCONTROL RM 52 SYSPLIT Type Remote controller user manual The design and specifications are subject to change without prior notice for product improvement Consult with the sales agency or manufacturer for details systemair CR035 RG52 2020550A8640 CONTENTS Handling the remote Controller ccccssceseeeeeeeeeeeeeeeeeeeeeeneneeeees 2 Remote controller Specifications cccccseeeseeesseeeeeeeeeeeeneseneees 3 PUNGTIOM DUO INS ssuneecisepsieteusee aaan A A 5 Indicators on LGD cierran ree E E EEEE EEEE 7 How TO use the buttons i saciedettencesescscinccevsctsoncucvetonsceapcicanteinsanncsies 8 Auto operation ssssnsnnnnnsnnnnnnnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nennen nnne 8 Cooling Heating Fan operation cccscccscssseessseeessseeeeseneeseeeeesees 8 Dehumidifying operation cccsccccesseeeeeeeeeseeeeeeeeeneseeeeenseeneeseeneess 9 Adjusting air flow GireCtion ccccsscceseeeeeeesneesseneeeseseeesenneesnenes 9 Timer operati M wissicicaicacsaicecaeccdavecitenxwansanasheincccstcapensasnsinestaecteeecenetian 10 Handling the remote controller Location of the remote controller e Use the remote controller within a distance of 8 meters from the appliance pointing it towards the receiver Reception is confirmed by a beep e Keep the remote controller where its signals can reach the receiver of the unit When you select the timer operation
5. crements to 30G DOWN Button 4 Push this button to decrease the indoor temperature setting in 1 C increments to 17 C SHORTCUT Button Used to restore the current settings or resume previous settings On the first time connecting to the power if push the SHORTCUT button the unit will operate on AUTO mode 26 C and fan speed is Auto Push this button when remote controller is on the system will automatically revert back to the previous settings including operating mode setting temperature fan speed level and sleep feature if activated And transmit the signals to the unit If pushing more than 2 seconds the system will automatically restore the current operation settings including operating mode setting temperature fan speed level and sleep feature if activated TIMER ON Button Press this button to initiate the auto on time sequence Each press will increase the auto timed setting in 30 minutes increments When the setting time displays 10 0 each press will increase the auto timed setting 60 minutes increments To cancel the auto timed program simply adjust the auto on time to 0 0 TIMER OFF Button Press this button to initiate the auto off time sequence Each press will increase the auto timed setting in 30 minutes increments When the setting time displays 10 0 each press will increase the auto timed setting 60 minutes increments To cancel the auto timed program simply adjust the auto of time to 0 0 DIRECT
6. e fan speed It has already been automatically controlled If the Auto mode is not comfortable for you the desired mode can be selected manually Cooling Heating Fan operation Ensure the unit is plugged inand poweris available Press the MODE button to select COOL HEAT cooling amp heating models only or FAN mode 2 Press the UP DOWN buttons to set the desired temperature The temperature can be setwithin a range of 17 C 30 C in 1 C increments 3 Press the FAN button toselect the fan speed in four steps Auto Low Med or High 4 Press the ON OFF button to start the air conditioner NOTE In the FAN mode the setting temperature is not displayed in the remote controller and you are not able to control the room temperature either In this case only step 1 3 and 4 may be performed 8 SLEEP FRESH SWING DIRECT Dehumidifying operation Ensure the unit is plugged in and poweris available The OPERATION indicator onthe display panel of the indoor unit starts flashing 1 Press the MODE button to select DRY mode 2 Press the UP DOWN buttons to set the desired temperature The temperature can beset within a range of 17 C 30 C in 1 C increments 3 Press the ON OFF button to start the air conditioner NOTE In the Dehumidifying mode you can not switch the fan speed It has already been automatically controlled Adjusting air flow direction Use the SWING and DIRECT button
7. leave the batteries in the remote controller if they are not going to be used for 2 or 3 months e Do not dispose batteries as unsorted municipal waste Collection of such waste separately for special treatment is necessary 2 Remote Controller Specifications RGS2A C EF RGS2BI C E RGS2CI CJE RG52DI C E RGS2A1 BG C EF RGS2B3 BG C E eae RGS2A BGICIEF RGS2B BGIC E RGS2BIIEF RGSZCIBG C E RGS2DIBGIC E 3 0V Dry batteries RO3 LR03 X2 Rated Voltage Signal Receiving 8m Range Environment Performance Feature 1 Operating Mode AUTO COOL DRY HEAT Cooling only model without and FAN 2 Timer Setting Function in 24 hours 3 Indoor Setting Temperature Range 17C 30C 4 Full function of LCD Liquid Crystal Display RGS2A BG C EF RGS2A C EF RG52A1 BG C EF RG52A1 C EF RG52B BG C E RG52B C E RG52B3 BG C E SLEEP SWING DIRECT NOTE RG52B3 BG C E models do not have FOLLOW ME function RG52B1 EF RG52D BG C E RG52D C E RG52C BG C E RG52C C E NOTE Buttons design might be slightly different from the actual one you purchased depending onindividual models e All thefunctions described areaccomplished by theindoor unit If the indoor unithas nothis feature there isno corresponding operation happened when press the relative button on the remote controller E B Function buttons OOO ON OFF Button Operation starts when this button is pressed and s
8. n is activated 2 0H on the TIMER OFF display 3 Press the TIMER ON button 4 Press the TIMER ON button again to display 10H on the TIMER ON display 5 Wait for 3 seconds and the digital display area will show the temperature again The TIMER ON OFF indicator remains on and this function is activated D 12 TIMER ON gt TIMER OFF Off gt Start Stop operation This feature is useful when you want to start the air conditioner before you wake up and stop it after you leave the house Example Start To start the air conditioner 2 hours after setting and stop it 5 hours after setting 1 Press the TIMER ON button ie a Be 2 Press the TIMER ON button again to display arestas fersat 2 0H on the TIMER ON display 3 Press the TIMER OFF button 4 Press the TIMER OFF button again to display 5 0H on the TIMER OFF display 5 Wait for 3 seconds and the digital display area will show the temperature again The TIMER ON OFF indicator remains on and this function is activated
9. shows TIMER OFF the last Auto off setting time and the signal H will be shown on the LCD display area Now it is ready to reset the Auto off time to stop the operation 2 Push the TIMER OFF button again to set desired Auto off time Each time you press the button the time increases by half an hour between 0 and 10 hours and by one hour between 10 and 24 hours 3 After setting the TIMER OFF there will be a one second delay before the remote controller transmits the signal to the air conditioner Then after approximately another 2 seconds the signal H will disappear and the set temperature will re appear on the LCD display window TIMER OFF Auto off Operation e When you select the timer operation the remote controller automatically transmits the timer signal to the indoor unit for the specified time Therefore The TIMER OFF feature is useful when you want the keep the remote controller in a location where it can transmit the signal to unit to turn off automatically after you go to bed The the indoor unit properly air conditioner will stop automatically at the set time The effective operation time set by the remote controller for the timer function is limited to the following settings 0 5 1 0 1 5 2 0 2 5 3 0 3 5 4 0 4 5 5 0 5 5 6 0 6 5 7 0 7 5 8 0 8 5 9 0 9 5 10 11 12 13 14 15 16 17 18 19 20 21 22 23 and 24 Example To stop the air conditioner in 10 hours 1 Press the TIME
10. the remote controller automatically transmits a signal to the indoor unit at the specified time If you keep the remote controller in a position that hinders proper signal transmission a time lag of up to 15 minutes may occur A CAUTIONS e The air conditioner will not operate if curtains doors or other materials block the signals from the remote controller to the indoor unit Prevent any liquid from falling into the remote controller Do not expose e the remote controller to direct sunlight or heat If the infrared signal receiver on the indoor unit is exposed to direct sunlight the air conditioner may not function properly Use curtains to e prevent the sunlight from falling on the receiver If other electrical appliances react to the remote controller either move these appliances or consult your local dealer Replacing batteries The remote controller is powed by two dry batteries RO3 LRO3X2 housed in the rear part and protected by a cover 1 Remove the cover by pressing and sliding off 2 Remove the old batteries and insert the new batteries placing the and ends correctly 3 Reattach the cover by sliding it back into position NOTE When the batteries are removed the remote controller erases all progra mming After inserting new batteries the remote controller must be reprogrammed A CAUTIONS e Do not mix old and new batteries or batteries of different types e Do not
11. to adjust the desired airflow direction 1 When push the DIRECT button the horizontal louver changes 6 degree in angle for each push NOTE On some models operate swing feature instead of this feature 2 When push the SWING button the louver will swing up and down automatically NOTE When the louver swing or move to a position which would affect the cooling or heating effect of the air conditioner it would automatically change the swing moving direction SLEEP FRESH SWING DIRECT Timer operation Press the TIMER ON button can set the auto on time of the unit Press the TIMER OFF button can set the auto off time of the unit To set the Auto on time 1 Press the TIMER ON button The remote controller shows TIMER ON the last Auto on setting time and the signal H will be shown on the LCD display area Now it is ready to reset the Auto on time to START the operation Push the TIMER ON button again to set desired Auto on time Each time you press the button the time increases by half an hour between 0 and 10 hours and by one hour between 10 and 24 hours After setting the TIMER ON there will be a one second delay before the remote controller transmits the signal to the air conditioner Then after approximately another 2 seconds the signal h will disappear and the set temperature will re appear on the LCD display window To set the Auto off time 1 Press the TIMER OFF button The remote controller
12. tops when this button is pressed again MODE Button Each time the button is pressed the operation mode is selected in a sequence of following NOTE Heat mode is for Cooling amp Heating models only FAN Button Used to select the fan speed in four steps AUTO LOW MED HIGH SLEEP Button Active Disable sleep function It can maintain the most comfortable temperature and save energy This function is available on COOL HEAT orAUTO mode only For the detail see sleep operation in USER S MANUAL NOTE While the unit is running under SLEEP mode it would be cancelled if MODE FAN SPEED or ON OFF button is pressed FRESH Button Active Disable FRESH function When the FRESH function is initiated the lonizer Plasma Dust Collector depending on models is energized and will help to remove pollen and impurities from the air TURBO Button Active Disable Turbo function Turbo function enables the unit to reach the preset temperature at cooling or heating operation in the shortest time if the indoor unit does not support this function there is no corresponding operation happened when pressing this button SELF CLEAN Button Active Disable Self Clean function LED Button Disable Active indoor screen Display When pushing the button the indoor screen display is cleared press it again to light the display 5 E UP Button Push this button to increase the indoor temperature setting in 1 C in
Download Pdf Manuals
Related Search