Home

Manual

1. Before start of engine the following shall be checked The engine shall be placed in a horizontal position Loosed the oil filling screw and fill with oil Oil If the oil level is below the mark on the oil stick fill with oil Always measure the oil level by putting the oil stick on top of the filling hole Use 15W 40 engine oil It has been specially manufactured for air cooled engines If this oil type cannot be procured a mineral oil with a viscosity of 15W 40 can be used Use only oil of good quality as SC SD SE SF and SG Inspect all bolts and nuts especially the ones fastening the accessories Inspect that the PTO power take off is in neutral Inspect that the air filter is not blocked dry filter and that oil has been applied to the oil bath filter Check oil height in the transmission box Fill with new gasoline leadless gasoline octane 95 When filling with fuel the machine must be placed in a horizontal position Old fuel shall always be replaced See engine manual for further details START OF ENGINE Disconnect the PTO of the machine 4 See engine manual for start of engine START OF MACHINE Apply the clutch and choose the requested gear 5 It may be necessary to press or tap the gear lever in order to connect Choose reverse or forward 6 Release the clutch handle 1 slowly and the machine starts running NB If the power take off is connected it will automatically disconnect when t
2. ndstof p arbejdst jet Hvis dette skulle ske skal t jet straks skiftes P fyld aldrig br ndstof i lukkede rum ARBEJDSBETINGELSER F r maskinen tages brug skal styret indstilles til den korrekte arbejdsh jde Veer forsigtig ved fr sning i hard og stenet jord Hav altid begge h nder pa styret s ledes at arbejdet kan ske p en rolig og forsvarlig m de Hvis din ProeTrac anvendes som fr ser b r jorden renses for store sten metaldele eller andre faste genstande inden arbejdet p begyndes Pas p skjulte r dder og tr stubbe Betjen kun maskinen ved passende lysforhold Arbejdet med maskinen skal foreg roligt og velovervejet Tjek med j vne mellemrum bolte og m trikker Ved m rkbare rystelser b r maskinen straks stoppes og fejls gningen begynde Af sikkerhedsm ssige hensyn skal motoren altid stoppes n r man forlader den TEKNISKE DATA PRO TRAC 555 R Motortype 5 0 HK Texas TG 160 Kobling Tor enkelt manuel kobling Gearkasse 3 Gear frem og 2 gear tilbage Hjul 4 00 x 8 00 Fr ser 58 cm Justerbar fra 37 cm H ndtag Justerbart i h jden side Vendbart 180 Bredde 57 cm med fr ser 80 cm med kost FOR START AF MOTOR BEM RK MOTOREN ER LEVERET UDEN OLIE F r start af motor skal f lgende tjekkes Motoren skal st i vandret stilling Oliep fyldningsskruen l snes og olien p fyldes Olien Er oliestanden under m rket p m lepinden p fyldes olie M l altid olieniveauet v
3. Benzin Stopkontakten er aktiveret Ingen benzin Benzinhanen er lukket Luftfiltret er stoppet Defekt t ndr r Gammel benzin Vil ikke tilkoble Juster koblingskablet LANGTIDS OPBEVARING I tilf lde af at din maskine skal opbevares i l ngere tid b r du f lge f lgende fremgangsmade for konservering Benzin T m benzintanken og start motoren Motoren vil g i sta af sig selv K r motoren varm Tap motorolien af P fyld straks ny motorolie Afmonter t ndr ret og h ld en skefuld motorolie ned i motoren Derefter tr kkes 2 3 gange i startsnoren Monter t ndr ret igen VEDLIGEHOLDELSE OG SMORRING Korrekt vedligeholdelse og sm ring forl nger levetiden af din fr ser og bor derfor f lges n je Motoren p din ProeTrac har en indk ringsperiode p 5 arbejdstimer Efter 5 timer skal motorolien skiftes derefter er skifteintervallet p 50 timer eller mindst n gang om ret Tjek oliestanden hver gang du skal bruge din maskine Tjek olien p gearkassen for hver 50 timer og skift mindst n gang om ret Brug en 80 90 gearolie Gearolien skal st op til niveau skruen 2 2 liter Hvis der er tegn p l kage fugtige udtr k o lign skal olien tjekkes jeblikkeligt Gearet p fr serhalen b r ligeledes tjekkes for hver 50 timer og skiftes n gang om ret Brug samme olie som p gearkassen fig 15 nr 1 BETJENINGSANORDNINGER Kobling Gas Vendbart styr PTO tilkobling
4. is warm Use a funnel or a container with a nozzle when filling with fuel Never smoke and avoid open fire during the filling If any fuel is spilled clean this immediately and the machine is started at a distance from the filling area Draw attention to not spilling fuel on your work clothing If this happens you have to redress Never fill with fuel in a closed room WORKING CONDITIONS Before the machine is being used the handle must be adjusted to the correct working height Be careful when cultivation hard and stony ground Always keep both your hands on the handlebar so that you can work in a calm and safe way The ground must always be cleaned from large stones metal parts or other firm objects before the work is started Watch out for hidden roots and logs Only operate the machine at appropriate lighting conditions Work with machine in a calm and well considered way Inspect bolts and nuts regularly At noticeable vibrations the machine shall be stopped and inspected for any faults For safety reasons the engine shall always be stopped when you leave it TECHNICAL DATA PRO TRAC 555 R Engine 5 0 HP Texas TG 500 Clutch Dry single manual clutch Transmission box 3 Gear forward and 2 reverse Wheel 4 00 x 8 00 Tiller 58 cm Adjustable from 37 cm Handle Adjustable in height side Turnable 180 Width 57 cm with tiller 80 cm with broom BEFORE STARTING THE ENGINE NOTE ENGINE IS DELIVERED WITHOUT OIL
5. the tiller box On the top of the tiller box where the tiller knives hang it is possible to change the depth by moving the bolt that fastens the knives You see three holes in the top and three holes below where it is possible to adjust the height of the knives in comparison to the tiller box Max cultivating depth is app 20 cm ProeTrac 555 R can be mounted with a side adjustable broom of 80 cm TRANSPORT WHEEL The rotary tiller can be mounted with a transport wheel which is a good thing when the machine is to be transported longer distances MOUNTING OF ACCESSORY It is very important you mount the accessory correctly Place the accessory so that it meets the power take off Push the accessory evenly on the two bolts Mount the bolts and fasten Inspect and fasten on a regular basis 00 Y O 01 When using quick clutch between accessory and machine it is equally very important that the accessory is mounted evenly on the machine An uneven mounting will destroy both bolts and the bushing of the power take off ILLUSTRATIONS
6. 2004 BETJENINGSVEJLEDNING TEXAS PROeI RAC 555 R TEXAS Andreas Petersen A S Knullen 2 5260 Odense S TIf 63955555 Fax 63 95 55 58 Internet adresse www texas dk E mail adresse post texas dk BETJENINGSVEJLEDNING Texas ProeTrac 555 R Tak for Deres valg af en Texas ProeTrac universaltraktor Vi er sikre pa at Deres nye maskine lever helt op til Deres forventninger om sikkerhed og ydeevne Texas arbejder konstant pa en forsat udvikling af maskiner og tilbeh r derfor forbeholder vi os retten til at ndre maskinerne b de i form teknik og design SIKKERHEDSFORESKRIFTER F r start af motoren skal denne betjeningsvejledning l ses og forst s Personer under 18 r m ikke arbejde med maskinen Ved arbejde med universaltraktoren b r sikkerhedsanvisningerne f lges n je Genneml s betjeningsvejledningen grundigt inden du starter din maskine V r sikker p at du omg ende kan stoppe maskinen og slukke motoren i tilf lde af uheld Samtlige instruktioner omkring sikkerhed og vedligeholdelse af fr seren tjener til din sikkerhed En ProeTrac m ikke bruges til andet arbejde end der er beskrevet i betjeningsvejledningen Brug kun tilbeh r og originale reservedele anbefalet af Texas Montering af ikke godkendte dele kan medf re for get risiko for defekt og er derfor ikke tilladt Ethvert ansvar fraskrives ved ulykke eller anden skade som for rsages pga montering af uoriginale dele F r maskinen tages i brug b r forhand
7. Gear Frem tilbage Justerbart styr NOR Nt VINTEROPBEVARING Safremt maskinen ikke skal anvendes over en l ngere periode b r f lgende regler for langtidsopbevaring f lges Reng r alle ydre dele pa universaltraktoren Eventuelle skader b r repareres inden oplagring Alle bev gelige dele sm res med en olie med god indtraengningsevne for at undg rustdannelser T m kaburator og breendstofsystem for br ndstof ved at lade motoren k re t r Afmonter t ndr ret og h ld 50 ml olie ned i bningen Tr k langsomt i startsnoren indtil der m rkes modstand Derved forhindres rustdannelse i cylinderen Skift olie p motor og gear Afd k maskinen og placer den i et t rt og rent lokale TILBEH R Den efterh ngte fr ser bruges til at forbehandle jorden for at klarg re den til s arbejdet Fr seren er forsynet med et jordspyd der bestemmer jords gningen N r jordspydet er helt oppe er der maksimal jords gning og der arbejdes med maksimal fr serdybde Arbejdsdybden kan justeres ved at l fte s nke knivene i forhold til fr serkassen P toppen af fr serkassen hvor fr serknivene er oph ngt er det muligt at ndre dybdegangen ved at flytte den bolt der holder knivene Der er tre huller foroven og tre huller forneden hvor det er muligt at ndre h jden p knivene i forhold til fr serkassen Maksimal fr serdybde er ca 20 cm ProeTrac 555 R kan monteres med svingbar kost p 80 cm TRA
8. Motorens omdrejningstal er indstillet fra fabrikken Den faste max indstilling beskytter motoren og m derfor ikke ndres Efterse maskinen for defekte betjenings og sikkerhedsm rker B r udskiftes hvis de er defekte ADVARSELSM RKER PAS P ROTERENDE KNIVE Arbejde med maskinen p stejle omr der er farligt Benyt kun maskinen p omr der hvor den kan h ndteres sikkert Ved arbejde med maskinen skal der benyttes t tsiddende t j solide arbejdshandsker samt sko st vler med skridsikre s ler OPSTART Husk at tjekke motoren for olie f r enhver opstart Hver gang maskinen benyttes skal fr seren efterses for evt fejl og mangler Opm rksomheden henledes is r p gasgrebet koblingsh ndtaget afbryderknappen knivene samt for ut theder i br ndstofsystemet Maskinen m kun startes p et plant underlag N r maskinen starter skal brugeren st fast og have godt greb i maskinen P FYLDNING AF BR NDSTOF V r forsigtig n r der p fyldes br ndstof da det er meget brandfarligt og indeholder giftige gasarter og eksplosive stoffer Der m aldrig p fyldes br ndstof n r motoren er i gang eller er varm Brug altid en tragt eller en dunk med h ldetud n r der p fyldes br ndstof Ryg aldrig og undg ben ild under p fyldningen Hvis der under p fyldningen spildes br ndstof skal det straks renses op og maskinen startes i god afstand fra optankningsstedet V r opm rksom p at der ikke spildes br
9. NSPORTHJUL Den efterh ngte fr ser kan monteres med et transporthjul som er en god ting hvis maskinen skal transporteres over l ngere afstande MONTERING AF TILBEH R Det er utroligt vigtigt at monteringen af tilbeh ret foreg r p en korrekt forsvarlig m de Skub tilbeh ret helt hen til udtaget Skub tilbeh ret lige p de to bolte P monter m trikkerne og sp nd skiftevis Tjek og eftersp nd ofte ROD Ved brug af kvik kobling mellem tilbeh r og maskine er det liges meget vigtigt at tilbeh ret monteres lige pa maskinen Et sk vt monteret tilbeh r vil kunne del gge bade boltene og kraftoverf ringsb sningen ILLUSTRATIONER 2003 1 USER MANUAL TEXAS PROeI RAC 555 R TEXAS Andreas Petersen A S Knullen 2 DK 5260 Odense S Tif 45 63 95 55 55 Fax 45 63 95 55 58 Internet adresse www texas dk E mail adresse export texas dk USER MANUAL Texas ProeTrac 555 R Thank you for choosing a Texas cultivator We are assure that the cultivator will meet your expectations of safety and performance Texas works constantly on continued development of machines and accessories and therefore we reserve the right to change the machines in shape technique and design SAFETY INSTRUCTIONS Before starting the engine this user manual shall be read and understood Persons under the age of 18 must not work with the machine When using the cultivator the safety regulations must be closely followed Read
10. and repairs Cleaning removal of block ups By transport and storage of the machine DAILY MAINTENANCE On a daily basis clean the engine and transmissin box for grass leaves and oil in order to avoid fire When using a hose to clean the machine you must never wash directly on the machine A damaged silencer causes too much noise and must be replaced By repairs you must only use original spare parts The number of revolutions of the engine has been determined from the fabric The permanent max adjustment protects the engine and must not be changed Inspect the machine for defect operation and safety labels Should be replaced if defect WARNING LABELS CAUTION ROTATING KNIVES Using the machine on steep areas is dangerous Only use the machine in areas where it can be manoeuvred safely When working with the machine use tight clothing solid gloves and shoes boots with non skid soles STARTING Inspect the engine for oil before every starting Inspect the machine for faults and wants every time it is used Draw attention to the throttle control clutch handle switch rotors and leakages in the fuel system You must only start the machine on an even surface When the machine starts the user must have a firm gripping in the machine FILLING WITH FUEL Be careful when filling with fuel as it is very flammable and contains poisonous gas arts and explosive material Never fill with fuel when the engine is running or
11. box every 50 hours and replace after 300 working hours Use a 80 90 transmission oil The transmission oil shall be fill to the screw 2 2 litre If there are any signs of leakage moist extracts ets the oil shall be checked immediately The transmission oil on the rotary tiller shall also be checked every 50 hours and replaced after 300 working hours Use the same oil as on the transmission box OPERATION FEATURES 8 Clutch 9 Gas 10 Turnable handlebar 11 PTO connection 12 Transmission 13 Forward reverse 14 Adjustable handlebar WINTER STORAGE If the machine is not to be used for a longer period of time the following prescription shall be followed Clean all external parts on the machine Any damages should be repaired before storage All moving parts shall be lubricated with oil with good penetrating abilities in order to avoid corrosion Empty the carburettor and fuel system of fuel by letting the engine run dry Dismount the sparking plug and pour 50 ml of oil into the opening Draw the starting cord until you feel resistance Thereby you avoid corrosion in the cylinder Change oil on engine and transmission Cover the machine and place it in a dry and clean room TILLER The rotary tiller is used to prepare the ground for the seeding work The tiller is equipped with an earth auger which determines the working depth The working depth can be adjusted by lifting lowering the knives in comparison
12. ed at l gge oliepinden l st oven p p fyldningshullet Brug 15W 40 motorolie Den er specielt fremstillet til brug p luftk lede motorer Hvis denne olietype ikke kan fremskaffes kan der bruges en mineralsk olie med en viskositet p 15W 40 Brug kun olie af god kvalitet som SC SD SE SF og SG Alle bolte og m trikker Is r dem der holder tilbeh ret At gearstang og PTO er i neutral At luftfiltret ikke er stoppet t rfilter og at der er olie p oliebadsfiltret Olieh jden i gearkassen P fyld ny frisk blyfri benzin oktan 95 Ved p fyldning af br ndstof skal maskinen st vandret Gammel br ndstof skal altid udskiftes Se motorvejledningen for vrig vejledning START AF MOTOR Afbryd maskinens PTO 4 Se motorvejledning for start af motor START AF MASKINE Udl s koblingen og placer gearstangen i det nskede gear 5 Det kan v re n dvendigt at trykke eller sl let p gearstangen for at tilkoble V lg bak eller frem 6 Slip koblingsh ndtaget 1 langsomt og maskinen begynder at k re NB Hvis kraftoverf ringen er tilkoblet vil det automatisk sl fra hvis maskinen s ttes i bakgear START AF TILBEH R Udl s koblingen 1 og tilkobl kraftoverf ringen 4 H v motoromdrejningerne 2 og slip koblingsh ndtaget 1 langsomt N r arbejdet er fuldf rt frakobles kraftoverf ringen 4 hvorefter motoren stoppes n r motorstoppet deaktiveres FEJLFINDING Motor vil ikke starte
13. he machine is in reverse START OF ACCESSORY Apply the clutch 1 and connect the power take off 4 Increase the engine revolutions 2 and release the clutch cable slowly 1 When your work has been completed disconnect the power take off 4 whereafter the engine stops when the engine stop is deactivated TROUBLE SHOOTING The engine will not start Gasoline The stop switch is activated No fuel The petrol cock is turned off The air filter is blocked Defect sparking plug Old gasoline Cannot throw into gear Adjust the clutch cable LONG TIME STORAGE In case that your machine is being stored for a longer period of time you must follow the following procedure Gasoline Empty the fuel tank and start the engine The engine will stop by itself Run the engine warm Drain for engine oil Fill immediately with new engine oil Dismount sparking plug and pour a spoonful of engine oil into the engine Thereafter pull the starting cord 2 3 times Remount the sparking plug MAINTENANCE AND LUBRICATION Correct maintenance and lubrication prolongs the life of your cultivator and should therefore be followed closely The engine of your Pro Trac has a running in period of 5 working hours After 5 hours the engine oil should be replaced and thereafter the shifting interval is every 50 hours or once a year Check the oil lever every time before you start your machine Check the oil on the transmission
14. leren eller anden fagkyndig instruere brugeren i korrekt brug og vedligehold af maskinen Den der betjener maskinen er ansvarlig for andre personer i arbejdsomr det Brug aldrig maskinen n r der er b rn eller dyr i n rheden Maskinen m kun bruges af personer som er fortrolig med betjeningen af maskinen Betjeningsvejledningen skal under alle omst ndigheder altid f lge maskinen Universaltraktoren m kun benyttes af personer som er udhvilede raske og i god form Hvis arbejdet er udmattende b r der holdes j vnlige pauser Efter indtagelse af alkohol m der ikke arbejdes med maskinen De fra fabrikken monterede styreenheder som f eks koblingskablet fra h ndtaget m ikke fjernes ARBEJDE P MASKINEN Hvis sikkerhedsudstyret afmonteres m maskinen ikke benyttes f r det er monteret igen Ved reng ring vedligeholdelse og montering af nedenst ende emner skal motoren v re afbrudt og t ndr rsh tten taget af t ndr ret Montering af tilbeh r Vedligeholdelse af motor eller maskine Justeringer og reparationer Reng ring fjernelse af tilstopninger Ved transport og oplagring af maskinen DAGLIG VEDLIGEHOLDELSE Reng r dagligt motoren og gearkassen for gr s blade og olie for at undg brand Ved brug af haveslange til reng ring af maskinen m du aldrig spule direkte p motoren En skadet lydd mper for rsager for meget st j og b r udskiftes Ved reparationer m der kun benyttes originale reservedele
15. the user manual thoroughly beforeyou start your machine Make sure that you are able to turn off the machine and engine in cas of accident All instructions concerning safety and maintenance of the cultivator serve for your safety A Pro Trac must not be used for any other work than described in the user manual Only use accessories and original spare parts recommended by Texas Assembly of non approved parts can cause increased risk of defect Texas is not responsible for any damage caused because of use of unoriginal parts Before using the machine the dealer should instruct the user in correct use and maintenance of the machine The one who operates the machine is responsible for other persons in the working area Never sue the machine when children or animals are near by The machine must only be used by persons who are confident with the machine The machine must only be used by persons who are not tired and in good shape You must not use the machine under influence of alcohol drugs or medicine The controlling units which was mounted from the side of the fabric like the clutch cable must not be removed WORK WITH THE MACHINE If the safety equipment is dismounted the machine must not be used again before it is remounted When cleaning maintaining and mounting of below mentioned subjects the engine must be turned off and the sparking plug cover dismounted from the sparking plug Maintenance of engine or machine Adjustments

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents