file
Contents
1. N Lit for 10 sec The tool communication with elevator is OK and the LCE user interface is open GREEN Blinking The tool receives a message from the LCECPU GREEN One Blink every 10 sec The tool has been re initialized ORANGE Blinking The tool receives a message from the LCECPU and tool has been used over 150 times This is warning that the tool should be re initialized soon 3 How to open LCE user interface with the tool The operating sequence is 1 Connect the tool port A to the RS232 port on LCECPU40 LCECPUS561 or LOPCB board either using cable coming with the tool or connecting port A directly into the connector Switch on the RS232 enable switch on LOPCB board in MAP Push the power button until the led turns on When the led has green or orange light on the LCE user interface is open Switch off the RS232 enable switch on LOPCB board in MAP Test the Menu access If OK disconnect the device otherwise repeat the step 2 5 De Pe S Copyright 2006 KONE Corporation All rights reserved2. User Manual 1 4 Global R amp D First Issue EDMS Code GSC 20 03 2006 884634en A 2 Compiled by Shaun Sequeira Date 20 03 2006 Issue 0 1 Changed by Kari Suihkonen 2006 Kone Corporation No of Pages 4 Checked by Kari Suihkonen Product code LCE Language en Approved by Drawing no XXXXXX SW Word 2000 LCEUIO DONGLE USER MANUAL Copyright 2006 KONE Corporation All rights reserved KONE User Manual 2 4 Global R amp D First Issue EDMS Code GSC 28 02 2006 884634en A 2 TABLE OF CONTENTS 1 INTRODUCTION sivic css cccceasccccsccssccocsessccssossscseseocsscssosssccedeossocdeccsbesedenscccsssasbecusecsects 3 2 BLOCK DIAGRAM vic vcsctssecccestsscccesesecevesisecesesscstecesaceceeesdsecevesesdcetesssceeceseceseeesesectoes 3 3 HOW TO OPEN LCE USER INTERFACE WITH THE TOOL c000 4 Copyright 2006 KONE Corporation All rights reserved KONE User Manual 3 4 Global R amp D First Issue EDMS Code GSC 28 02 2006 884634en A 2 1 Introduction The user interface of all LCE based elevators which have 6 X X based software or newer will be locked after 10000 starts The LCEUIO tool can be used to unlock the LCE user interface and the serial port of the CPU board for elevators which have 6 7 18 or newer software This document explains the functionality and use of the LCE User Interface Opening LCEUIO tool 2 Block Diagram Power button Figure 1 The user interface
3. of the tool contains following main parts figure 1 e Port A D9 connector will be connected to corresponding connecter on LCECPU40 LCECPUS561 or LOPCB board in MAP e Power button Power switch is used to start and shut down the battery power e Led is used for diagnostic purposes Different warnings and errors have been defined in the table e Port B D9 connector is supposed to be used when troubleshooting tools LCETERM are connected to the tool e DC provides a connector to extern power supply 10 24V for example Mascot 9525 12VD e On the backside of the tool there is a 9V battery behind the cover e 2 extent cables including in the package One for LCECPU20 for different adapter Another one for LCECPU40 or LCELOB for easy connection Copyright 2006 KONE Corporation All rights reserved KONE User Manual 4 4 Global R amp D First Issue EDMS Code GSC 28 02 2006 884634en A 2 LED State Description RED Lit for 10 sec Tool has been used for 200 times and it is locked Tool must be re initialized with the re initialization tool before it can be used again RED Two blinks every 10 sec The tool can t open LCE user interface RED Three blinks every 10 sec The tool can t communicate with elevator This can occur if there is communication problem or LCECPU software does not support the LCEUIO tool RED Continuous blinking Internal error in the tool Tool is broken GREE
Download Pdf Manuals
Related Search