User manual type 34003095
Contents
1. eld Eri 7 1 Power off activated Power on option An EXT controlled device will always automatically power on when selected But it is not always practical if a device automatically powers off when another source is selected or the TV is turned off An example could be a Satellite receiver that is being used in more than one room If a user in a link room is watching programmes from the receiver it is not practical that the receiver automatically powers off when the user in the main room turns off the TV or selects another source If a recorder has been timed to record from the receiver it would also be a problem if the system automati cally powers off the receiver Many devices use so much time running a booting sequence that you might want them to never power off for this reason only In order to set these options press the following sequences within 10 seconds Euren uri Eri 6 Power on deactivated STOP STOP STOP Euren STOP STOP 6 1 Power on activated one gt remote Installation The OneRemote EXT cable must be connected to the devices scart output socket and a scart input socket on the TV Then the IR emitter must be stuck in a way that it can emit IR light in to the the devices IR receiver that normally receives the IR light emitted thom the devices own remote control Only scart input sockets can be used that are able to send out li2. P Channel up down or CH Programme stepping up down manoeuvring in menus Most set top boxes or TV s has 4 arrow buttons for moving up down left and right in on screen menus In addition they have separate programme stepping buttons for zapping through programmes B amp O remote control does not have separate buttons for programme zapping We therefore have chosen the blue and the yellow buttons to function as programme stepping buttons The four up down left and right buttons have been assigned for manoeuvring in on screen menus in our basic setup It is possible to use the up and down arrow for programme stepping refer to the installation section Go Record and Stop shifted operation Some of the buttons has two or three functions To get to these they have to be preceded with or some time The buttons that has been assigned secondary functions on this controller can be seen in the operating table on page 2 Option programming The OneRemote EXT controller can be programmed with different options to fit different set ups An option programming is done by pressing a series of buttons in a special scheme that does not occur during daily use A pro gramming must be ended within 10 seconds To abort an ongoing programming sequence press one gt remote Menu option If the device is used in a setup that includes a Bang amp Olufsen TV sometimes the use of the REW button creates a conflict Some Bang
3. amp Olufsen TV act on the MET and enters its own TV On Screen Menu regardless of which source it is set to In these setups the Menu button must be disabled on the EXT controller Instead of using the Menu button to access the devices Menu use the alternative menu operation In order to set these options press the following seguences within 10 seconds STOP STOP STOP STOP 8 Menu button deactivated STOP STOP stop 1 Menu activated Power off option An EXT controlled device will always automatically power on when selected But it is not always practical if a device automatically powers off when another source is selected or the TV is turned off An example could be a Satellite receiver that is being used in more than one room If a user in a link room is watching programmes from the receiver it is not practical that the receiver automatically powers off when the user in the main room turns off the TV or selects another source If a recorder has been timed to record from the receiver it would also be a problem if the system automati cally powers off the receiver Many devices use so much time running a booting sequence that you might want them to never power off for this reason only In order to set these options press the following sequences within 10 seconds EC 7 Power off deactivated
4. with DVI and or HDMI sockets a suitable cable can be added to improve the picture quality The EXT cable will still be needed for control data and maybe also the sound Refer to the user manuals for both the TV and the device about correct installation of HDMI DVI cables In a setup with link rooms all rooms will be able to operate the device via the link system one gt remote Operating with OneRemote To be able to operate the device correctly with a B amp O remote control the user has to be familiar with operations with the original remote control as described in the device s user manual B amp O remote controls are not equipped with many keys so we have designed a layout that works logically even when shifting between different devices To get a common layout for many devices we therefore needed to redefine a few of the beo4 buttons to other functions Coloured buttons To make room for direct access to important functions we have moved the coloured buttons to a lower layer To send a red button command must be pressed before the red button 07 will send the actual red com mand The same goes with the other 3 coloured buttons This way we are able to assign other functions to the coloured but tons when they are pressed directly In a OneRemote environment the coloured buttons is mostly assigned to these operations Guide EPG or similar a Back Backup Return or similar 4 Programme zapping
5. User manual type 34003095 EXT 0009 009090 0090 0000 000 User manual English OneRemote EXT set top box controller Only for connection to a Bang amp Olufsen or compatible TY Operate these and other devices with a B amp O remote control b d es pi tea sini ak ulum Samsung SMT H6106 3 Samsung TV SHD 85 O e Receiver for Orange one gt remote Operation with Beo4 or Beo5 Daily use Playback OK Play Pause press 1 sec gt Play Pause alternative 1 Retour 2 4n P Stop 1 B amp 44 Rew FF EXIT Quit Next amp v Previous Record Other operations 1 As the coloured buttons has been assigned other direct functions a b Guide has to be pressed first to get the coloured operation mm Info a Green VOD e Yellow Liste v Blue NUM Format 4 Red NEN Power manual Special or alternative operations MENU Menu Beolink 1000 and other remote controls Operation is optimal with Beo4 or Beo5 that has coloured function Beolink 1000 Operation buttons Other remote controls can be used with limited operation As newer remote controls This is special operation keys included on these remote controls Green function key Eo etour Yellow
6. function key Mena EUN Blue function key Quit ma Red function key Arya one gt remote Congratulations The EXT controller from www oneremote dk can fully operate your device using your Bang amp Olufsen remote control terminal via a Bang amp Olufsen TV Beo4 or Beo5 remote controls can be used Beolink 1000 can be used with reduced functional ity This guide explains how This EXT controller is ready for use plug amp play See the opposite page regarding daily opera tion Some operations can be altered to improve interaction with other controllers or to your con venience Refer to the installation section further on if changes are needed one gt remote EXT controller When a scart type connected source is selected with a Bang amp Olufsen remote control the B amp O TV starts to parse control data from the remote control to the attached device via the scart cable The OneRemote EXT controller captures these data and converts these into IR data that can operate the specific device The converted IR data is being transmitted via a small IR emitter that has to placed in front of the device to be controlled Here it emits the same IR data into the front of the device that it was made to receive from its own remote control As an EXT controller operates on data received via the scart cable it will function only when attached to a B amp O TV If both the B amp O TV and the device are equipped
7. nected to a device or if it is connected to a device that is powe red off If not connected to the TV output socket of a device the EXT controller will not be able to measure if the device is powered on and therefore always light green LED short flash off During use the LED will light red or green depending on the powerstatus of the device When receiving a controldata from the TV the control LED will shortly go out to indicate this If a button is pressed on the TV s remotecontrol supposed to operate the device and teh LED does not indicate this the TV has not been correctly set up 9 0W91 9U0 www oneremote dk Made in Denmark 34003097uluk
8. nkdata to the EXT controller Also the TV must be programmed to send out data to the scart socket which is done in the TV s Sources menu Refer to the TV s user manual The EXT controller emulates DVD VMEM VTAPE SAT DTV VAUX and other sources There is no programming needed on the EXT controller The scartplug in that end of the EXT cable where the power supply and the IR emitter cable is attached MUST be inserted in to the devices TW output If not the EXT controller might not be able to power on and off the device correctly The control LED The EXT cable is equipped with a control LED build in to the scartplug that is inserted in to the device This LED assists in faultfinding if something is not operating correctly Continous flashing When power is applied to the EXT controller the LED will start flashing The flash indicates that the EXT controller has not received a command data from the TV since power on As soon as a command is received from the TV the LED wil stop flashing and light solid red or green If the control LED continues flashing after you have selected the source on the TV where the cable is attached the socket does not include control data or the TV has not been set up correctly Refer to the TV s user manual LED colour The EXT controller will light red when it has detected a device that is powered on It will either flash or light solid red The EXT controller will light green when it is not con
Download Pdf Manuals
Related Search