User manual of DS-2CC51A1/51A5/51A7P(N)-VF
Contents
1. Day Night High definition Dome Camera User Manual MANUAL Selecting MANUAL and pressing the button to enter the MANUAL WB submenu Customize the LEVEL value on your demand MANUAL WB LEVEL l 064 RETURN Figure 3 6 MANUAL WB PUSH In the PUSH mode the viewed image retains color balance automatically The color in the image balances according to the color temperature PUSH LOCK In the PUSH LOCK mode you can select a scene and manually adjust the white balance and then lock the color temperature It is suitable for the environment which the color temperature slightly changes ANTICR Anti Color Rolling In ANTI CR mode the system suppresses the color rolling under the fluorescent light environment 35 Day Night High definition Dome Camera User Manual 3 1 5 Backlight Setting Move the cursor to the BLC and select OFF BLC or HLC by pressing left right button BLC Backlight Compensation If there s a strong backlight the object in front of the backlight appears silhouetted or dark BLC can correct the exposure of the subject But the backlight environment is overexposed e HLC Highlight Compensation HLC masks strong light sources that usually flare across a scene This makes it possible to see the detail of the image that would normally be hidden 3 1 6 Picture Adjust Setting Move the cursor to PICT ADJUST Press the confirm button to enter the PICT ADJUST s2. User Manual 2002 96 EC WEEE directive Products marked X with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper ooo recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info Day Night High definition Dome Camera User Manual Safety Warnings and Cautions Please pay attention to the following warnings and cautions Hazardous Voltage may be present Special measures and precautions must be taken when using this device Some potentials voltages on the device may present a hazard to the user This device should only be used by Employees from our company with nowledge and training in working with these types of devices that contain live circuits Caution The power supply in this product contains no user serviceable parts Refer servicing only to qualified pe
3. MOTION DET SETUP MODE ON v TYRE d v AREA SET 1 v SENSITIVITY 004 RETURN Figure 3 22 Motion Detection 61 Day Night High definition Dome Camera User Manual TYPE1 TYPE2 and TYPES are selectable for motion detection type TYPE1 1 Move the cursor to TYPE and select TYPE 1 2 Move the cursor to AREA SET and press confirm to select the area up to four areas are selectable 3 Move the cursor to AREA SET and press confirm Move the cursor to AREA SEL to select one area 4 Move the cursor to MODE and press confirm to enable or disable the areas 5 Move the cursor to TOP BOTTOM LEFT RIGHT to adjust the area size and position 6 Move the cursor to RETURN and press confirm to exit 3 Move the cursor to SENSITIVITY and press left right to select sensitivity value from 0 to 7 4 After the settings move the cursor to RETURN and press confirm button to return to the previous menu TYPE 2 1 Move the cursor to TYPE and select TYPE 2 The area setting is not available now 2 Move the cursor to SENSITIVITY and press left right to select sensitivity value from 0 to 7 3 After settings move the cursor to RETURN and press confirm to return to the previous menu 62 Day Night High definition Dome Camera User Manual TYPE 3 1 Move the cursor to TYPE and select TYPE 3 2 Press up down to select AREA SET and press menu button to set the motion detection areas 3 Hold menu bu
4. Day Night High definition Dome Camera User Manual MOSAIC DAY NIGHT AUTO COLOR B W NR Y LEVEL CAMERA ID SYNC INT LINELOCK LANGUAGE English Chinese Japanese Fre nch Russian Portuguese Spanish German CAMERA RESET DPC EXIT SAVE ALL Note This series of camera adopts joystick control You can select the menu item by setting the joystick which is beside the lens to up down left right 3 1 2 Lens Settings Move the cursor to LENS and then set the menu button left right to select MANUAL or AUTO Selecting MANUAL mode you have to adjust the LENS IRIS manually Selecting AUTO mode press the button to enter the AUTO IRIS submenu 29 Day Night High definition Dome Camera User Manual AUTO IRIS TYPE DC MODE AUTO SPEED l 080 RETURN Figure 3 1 AUTO IRIS AUTO IRIS function can automatically open and close the iris according to the changing light conditions TYPE The type is DC MODE Choose the iris mode AUTO OPEN and CLOSE are selectable SPEED Adjust the auto iris speed The higher the value the faster the auto iris The value ranges from 0 to 255 Note It s recommended that you adjust the iris speed only when the iris vibrates 3 1 3 Shutter AGC Setting SHUTTER AGC allows you to adjust the way the system balances SHUTTER and AGC settings in different light conditions You can 30 Day Night High definition D
5. LOW RETURN Figure 3 8 ATR 3 1 8 Motion Detection Setting There are two kinds of MOTION DET panes BLOCK DISP and MONITOR AREA Two panes can take effect simultaneously BLOCK DISP Steps 1 Move the cursor to MOTION DET and select ON and press the menu button to enter the submenu 38 Day Night High definition Dome Camera User Manual DA DS Position the cursor on DETECT SENSE and set the menu button left right to adjust the sensitivity level Position the cursor on BLOCK DISP and set the menu button left right to select ENABLE Press the menu button to enter the setup interface of the detection panes Select ON to enable BLOCK DISP Move the cursor to MONITOR AREA and select ON Return to the MAIN MENU and click SAVE ALL You can find the BLOCK DISP take effect after you exit the main menu MONITOR AREA Steps 1 Move the cursor to MOTION DET select ON and press the menu button to enter the submenu 2 Position the cursor on DETECT SENSE and set the menu button left right to adjust the sensitivity level 3 Position the cursor on MONITOR AREA Select OFF to disable area motion detection Select ON to enable area motion detection 4 Position the cursor on AREA SEL to select one area There are four areas available 39 Day Night High definition Dome Camera User Manual 5 Set the values of TOP BOTTOM LEFT and RIGHT The size and position of the area is defined by these
6. The camera adjusts the speed automatically e MANUAL mode Select the MANUAL mode Adjust the damping value to set the speed of the iris The value ranges from 0 to 15 The larger the value is the slower the speed is 66 Day Night High definition Dome Camera User Manual IRIS ADJUST MODE MANUAL V DAMP 004 RETURN Figure 3 26 IRIS ADJUSTING 3 2 5 System CAMERA ID Move the cursor to Camera ID and press confirm to enable or disable this setting OFF The camera ID will not be displayed after the exit ON The camera ID will be displayed after the exit Set the camera ID On and press confirm button to enter Camera ID menu 67 Day Night High definition Dome Camera User Manual Camera ID Camera ID ON v ABCDEFGHIJKLMNOPQRSTUV WXYZ0123456789 amp OQ lt gt 7 x CLRIPOS RETURN Figure 3 27 Camera ID Steps 1 Move the cursor to the characters numbers and symbols 2 Press confirm to select one The selected character will be displayed on the dotted line 3 Move the cursor to 4 Press confirm to move to the character that needs to be modified and select another character to replace it 5 Move the cursor to CLR to clear all the characters on the dotted line 6 Move the cursor to POS to edit the camera ID position 1 Move the cursor to POS 2 Press confirm to enter the CAM ID position setting interface 3 Press up down
7. areas simultaneously in the field of view WDR balances the brightness level of the whole image and provide clear images with details EIS Electronic Image Stabilization Electronic image stabilization function can reduce certain ranges of vibration which is caused by the external environment 3D Digital Noise Reduction Comparing with the general 2D digital noise reduction the 3D digital noise reduction function processes the noise initiated by 73 Day Night High definition Dome Camera User Manual CCD besides processing the noise in the separated Y video signal and C video signal HLC High Light Compensation The HLC is capable of detecting and reversing the bright spots in the picture such as headlights to black so as to achieve optimum picture quality Digital Zoom Digital zoom helps to crop the entire image and then digitally enlarge the size of a portion of image that is needed to zoom in on 74 Day Night High definition Dome Camera User Manual 2 Troubleshooting Problem 1 Why does the camera restart intermittently And the problem is much more serious when infrared lights of IR camera are turned on at night Possible Reasons The main and common reason is power supply shortage This problem may happen to the IR camera especially at night because the infrared lights are turned on at night and increase the power consumption To Solve the Problem You need to ensure that the power supply m
8. be between 10 C 60 C dusty or damp locations and do not expose it to high electromagnetic radiation To avoid heat accumulation good ventilation is required for a proper operating environment Do not let water and any liquid flow into the camera While shipping the camera should be packed in its original packing or packing of the same texture Improper use or replacement of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteries according to the instructions provided by the battery manufacturer 11 Day Night High definition Dome Camera User Manual Table of Contents 1 Introduction 1 1 Product Features 1 2 OVGIIGWE ats ESE ESEG K ENS anse ER RES Pe GEE DERE SE ENS dei 2 Installation eee RR RARR AAR EE EA EE EE KERK kk kk kk Rek RR RNAAR EA 2 1 Ceiling Mounting 2 2 In ceiling Mounting Without Gang Box 2 3 Wiring 3 Menu Operation iese ee EER KERE EER AE EE KERR RE EER RARR ERK RARR EE 28 3 1 Menu Description A 28 3 1 1 Menu OVervieW esse ese eke EE EE EK Re eek ke 28 1 2 Lens Settings 1 3 Shutter AGC Setting 1 4 White Balance Setting sesse sesse ee ee 1 5 Backlight Setting 1 6 Picture Adjust Setting 1 7 ATR Setting 1 8 Motion Detection Setting iese ee ee 38 1 9 Privacy Mask Setting 1 10 Day Night Setting 11 NR Setting 12 Camera ID Setting enserir 13 SYNC Setting 14 Language Setti
9. detection is on up to 4 privacy areas are configurable 41 Day Night High definition Dome Camera User Manual 3 1 10 Day Night Setting Move the cursor to DAY NIGHT and select AUTO COLOR or B W by setting the menu button to left right COLOR mode is used for normal lighting conditions B W mode can increase the sensitivity in low light conditions AUTO Mode Setting In AUTO mode the day mode and the night mode can switch automatically Steps 1 After moving the cursor to DAY NIGHT set the menu button left right to select AUTO 2 Press confirm to enter the submenu BURST Select ON or OFF to enable or disable this feature DELAYCNT The value ranges from 0 to 255 This value is the delay time before the day night mode switches DAY NIGHT The value ranges from 0 to 255 The day mode switches to the night mode when the light condition reaches to the value you select NIGHT gt DAY The value ranges from 0 to 255 The night mode switches to the day mode when the light condition reaches to the 42 Day Night High definition Dome Camera User Manual value you select DAY NIGHT BURST DELAY CNT DAY NIGHT NIGHT DAY RETURN Figure 3 11 DAY NIGHT B W Mode Setting In the B W submenu you can enable or disable the BURST B W BURST OFF RETURN Figure 3 12 B W 43 Day Night High definition Dome Camera User Manual 3 1 11 NR Setting Noise Reduct
10. left right to change the position of camera ID 68 Day Night High definition Dome Camera User Manual 4 Press confirm to exit the CAM ID position setting interface and return to the CAM ID menu 7 Move the cursor to RETURN and press confirm to return to the previous menu SYSTEM INFO Move the cursor to SYSTEM INFO and press confirm to check the hardware software and DSP version information The system information is used for device maintenance or repair SYSTEM INFO HARDWARE REV1 00 SOFTWARE REV1 00 00 DSP REV1 00 00 RETURN Figure 3 28 System Information CAMERA RESET Move the cursor to CAMERA RESET and press confirm to reset the camera parameters to the factory default settings 69 Day Night High definition Dome Camera User Manual 3 2 6 Language Move the cursor to LANGUAGE and press confirm to enter the submenu select a language Move the cursor to RETURN and press menu button to return to the previous menu 3 2 7 Exit Move the cursor to EXIT and press confirm to enter the menu Press up down to select SAVE ALL CANCEL and RETURN CANCEL Press confirm to cancel the settings and exit the menu SAVE ALL Press confirm to save the settings and exit the menu RETURN Press confirm to return to the previous menu 70 Day Night High definition Dome Camera User Manual Appendix 1 Glossary Note The glossary gives brief explanations to the basic operation principle or th
11. position the camera ID 3 Press the button to save the position and exit 45 Day Night High definition Dome Camera User Manual CAMERA ID ABCDEFGHIJKLMNOPQRSTUV WXYZ0123456789 amp OZ Vie SOW x4 l CLR POS RETURN Figure 3 14 CAMERA ID 3 1 13 SYNC Setting Both internal and line lock synchronization are available Note Only the camera which supports both DC 12 V and AC 24 V has line lock synchronization If 12V DC power supply is applied SYNC mode is internal synchronization and it is not adjustable If 24V AC power supply is applied you can select either internal or line lock synchronization Note Internal synchronization is the default SYNC method Set the menu button to right for about 2 seconds you can switch the SYNC mode to line lock from the SYNC settings Perform the same operation to switch it to internal synchronization from the line lock 46 Day Night High definition Dome Camera User Manual 3 1 14 Language Setting This series of camera supports multi language English default Chinese Japanese French Russian Portuguese Spanish and German are selectable Steps 1 Move the cursor to LANGUAGE 2 Setthe menu button left right to select the language you need 3 1 15 Camera Reset Setting Move the cursor to CAMERA RESET and press the menu button to reset all camera settings to the default 3 1 16 Defective Pixel Correct Setting P
12. the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance To reduce the risk of fire or electrical shock do not expose this product to rain or moisture This installation should be made by a qualified service person and should conform to all local codes Please install blackouts equipment into the power supply circuit for convenient supply interruption Please make sure that the ceiling can support more than 50 N Newton gravities if the camera is fixed to the ceiling A Cautions Make sure the power supply voltage is correct before using the camera Do not drop the camera or subject it to physical shock Do not touch sensor modules with fingers If cleaning is necessary use a clean cloth with a bit of ethanol and wipe it gently If the camera will not be used for an extended period of time put on the lens cap to protect the sensor from dirt e Do not aim the camera at the sun or extra bright places A blooming or smear may occur otherwise which is not a malfunction however and affecting the endurance of sensor at the same time 10 Day Night High definition Dome Camera User Manual The sensor may be burned out by a laser beam so when any laser equipment is being used make sure that the surface of the sensor will not be exposed to the laser beam Do not place the camera in extremely hot or cold temperatures the operating temperature should
13. AI auto iris mode Or you can adjust the focus in low illumination condition such as at night Problem 4 Acamera with OSD menu and an auto iris lens displays black video but the OSD menu can be called and displayed 76 Day Night High definition Dome Camera User Manual Possible Reasons Auto iris lens connector is loose contact Or the iris driven mode of the camera does not match with the mode of auto iris lens To Solve the Problem Check the auto iris lens connector to ensure good contact Set the iris driven mode of the camera the same as the mode of lens The modes can be VD video drive or DD direct drive DD mode is commonly used 3 Technical Maintenance Lens Maintenance The lens surface is plated an anti reflection coating The dust oil and finger print etc will cause scratch mildewed and performance degraded Please refer to the following method to clean the lens Handling dust Use oil free soft brush or blowing dust ball to clean the dust Handling oil Steps 1 Wipe off the water drop or oil by soft cloth and dry the lens 2 Use oil free cotton cloth or lens clean paper to wipe the lens from center to outside with alcohol or detergent 3 Change the cloth to wipe the lens until the lens is clean 77 Day Night High definition Dome Camera User Manual Bubble Maintenance of Domes The bubble is of transparent plastic The dust oil and finger print etc will cause sc
14. E ON Vv VALUE 004 CONTRAST 005 RETURN Figure 3 20 Digital WDR 2 Move the cursor to VALUE which is used to set the image brightness from 0 to 15 3 Move the cursor to CONTRAST which is used to set the image contrast from 0 to 15 4 Move the cursor to RETURN and press confirm to return to the previous menu Note The Digital WDR is disabled when the BLC mode is ON SMART IR Settings Move the cursor to SMART IR and press confirm to enter the SMART IR SETUP menu The SMART IR value can be adjusted from 0 to 7 It is disabled when the value is 0 58 Day Night High definition Dome Camera User Manual 3 2 4 Funtion SYNC Support internal and line lock synchronization When using DC12V power supply it displays internal synchronization and is not adjustable When using AC24V you can select either internal or line lock synchronization WHITE BALANCE Move the cursor to WHITE BALANCE and then press confirm button to select the item from ATW1 ATW2 Auto or Manual ATW1 The camera adjusts the color temperature automatically according to the actual environment color temperature the temperature range is approximate from 2500K to 9500K ATW2 The temperature range is approximate from 2500K to 15000K ATC Adjust the color temperature under the steady color temperature environment After selecting ATC the white balance will take effect on the current scene image Manual Adjust red and b
15. HIK VISION Day Night High definition Dome Camera User Manual www hikvision com UD 6L0201D0070A01 Day Night High definition Dome Camera User Manual Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual applies to following cameras Models Models DS 2CC5181P N VF DS 2CC5185P N VF DS 2CC5191P N VF DS 2CC5195P N VF DS 2CC51A1P N VF DS 2CC51A5P N VF DS 2CC5183P N VF DS 2CC5187P N VF DS 2CC5193P N VF DS 2CC5197P N VF DS 2CC51A3P N VF DS 2CC51A7P N VF This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS 1 Day Night High definition Dome Camera User Manual WHATSOEVER REGARDING THE PERFORMANCE O
16. High definition Dome Camera User Manual X2 x4 x8 and x16 are selectable Select one value and press confirm to save and return to the previous menu Note The Motion Detection and the Digital Zoom function will be disabled if the ANTI SHAKE is on MIRROR OFF H FLIP V FLIP or CENTER is selectable PIXEL CORRECT Charge Coupled Device CCD will appear blemish after a long time usage and this series of camera possesses auto repair function to solve this problem Move the cursor to PIXEL CORRECT and press confirm The PIXEL CORRECTING will be displayed on the screen and the screen will go blank to correct the pixel After the pixel gets corrected the menu will return to the FUNC page Note This function will be more active in the absolutely dark environment Make sure that the lens s IRIS is closed before using this function HLC Move the cursor to HLC and press confirm to enable or disable this function If HLC is enabled the corresponding parameters can be configured in HLC menu as shown below 65 Day Night High definition Dome Camera User Manual RETURN Figure 3 25 HLC Move the cursor to VALUE which can be set from 0 to 7 The larger the value is the lower the restrained brightness threshold is IRIS ADJUST You can adjust the zoom speed of the iris in this menu There are two modes to adjust the speed e AUTO mode Select the AUTO mode and aim the camera at the high light scene
17. R RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT 0100001021113 Day Night High definition Dome Camera User Manual Regulatory Information FCC Information FCC compliance This eguipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio freguency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be reguired to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is Subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied C accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC Day Night High definition Dome Camera
18. TER POSITION ENTER VALUE Ee 007 RETURN Figure 3 17 BLC SETUP e WIDE DYNAMIC RANGE Purpose The Wide Dynamic Range function combines a long time exposed image and a short time exposed image to get an image for both bright and dark areas to be visible Steps 1 Move the cursor to BLC WDR and press the menu button to enter the BLC WDR menu 2 Position the cursor on the WDR and press the menu button to enter the WDR settings menu 3 You can set the VALUE CONTRAST and WD ADJUST in this menu e The VALUE ranges from 0 to 15 The larger the value is the longer the exposure time is The dark areas will be brighter in the image 53 Day Night High definition Dome Camera User Manual e You can adjust the CONTRAST value after the setting of WDR VALUE e If the effect of WDR is not obvious in the dark scene you can turn onthe WD ADJUST to enhance the WDR But the noise in the image will be amplified too Do not turn this function on in the normal scene 4 Move the cursor to RETURN and press the menu button to return to the previous menu BLC WDR SETUP MODE VALUE CONTRAST WD ADJUST ON v H COLOR ADJ OFF Vv RETURN Figure 3 18 WDR SETUP DAY NIGHT Move the cursor to DAY NIGHT and press menu button to enter the DAY NIGHT edit mode DAY NIGHT and AUTO mode are selectable AUTO mode Steps 54 Day Night High definition Dome Camera User Manual 1 Select AUTO and pr
19. User Manual 3 2 2 Scene There are 6 scenes selectable INDOOR STD INDOOR BACKLIGHT OUTDOOR LOW LUMINANCE IRSTD and CUSTOMIZE You can select one of the scenes according to the application condition Under CUSTOMIZE mode the scene parameters can be configured manually to get the best image quality when the monitoring conditions are complicated Note DS 2CC5187 5197 51A7P N VF doesn t support IRSTD 3 2 3 Exposure LENS Settings Purpose From this menu you can set the lens mode to adjust the image brightness Steps 1 Move the cursor to LENS and press the menu button to enter the LENS SETUP menu 2 Position the cursor on LENS in the LENS SETUP menu ELC ALC and ELC ALC are selectable e ELC If you choose ELC the camera adjusts the electronic shutter value automatically according to the VALUE setting The iris is 50 Day Night High definition Dome Camera User Manual opened to the maximum size The shutter value in the SHUTTER SETUP menu is AUTO e ALC If you choose ALC the camera adjusts the iris automatically according to the value setting The electronic shutter value is a fixed value The shutter value in the SHUTTER SETUP menu is adjustable e ELC ALC If you choose ELC ALC according to the VALUE setting the camera automatically adjusts the electronic shutter and the iris too The electronic shutter value will be in the range from1 50s to the value you set in the SHUTTER SETUP men
20. adapt to the different surveillance environments 14 Day Night High definition Dome Camera User Manual Auto gain control adaptive brightness Privacy mask with 8 optional colors and 8 configurable areas Advanced 3 axis design makes this series of dome camera is applicable to the different installation environment The main features of DS 2CC5183 5193 51A3P N VF DS 2CC5185 5195 51A5P N VF and DS 2CC5187 5197 51A7P N VF are as follows High performance SONY CCD providing high quality image Color minimum 0 001Lux F1 2 B W minimum 0 0001Lux F1 2 ICR filter auto switch Support Wide Dynamic Range WDR for backlighting surveillance supported by DS 2CC5187 5197 51A7P N VF OSD menu which enables user to configure the detail parameters Back Light Compensation BLC with programmable BLC area Auto white balance with high color rendition High SNR which brings clear and high quality image 3D digital noise reduce to get clear and fine image Support SMART IR Electronic image stabilization EIS function to get steady and clear image Auto electronic shutter control to adapt to the different surveillance environments 15 Day Night High definition Dome Camera User Manual Auto gain control adaptive brightness Support auto iris Privacy mask with 8 optional colors and 12 configurable areas Advanced design technology with high reliability Advanced 3 axis design allows the dome camera to meet the diffe
21. atches with 10 of the nominal voltage And the power consumption of power adapter should meet the demand of the camera Problem 2 The camera can never be focused by adjusting the focus stick on the lens And there is also no use adjusting the back focus Possible Reasons The camera needs the lens with CS lens mount When you installa lens with C lens mount the camera will never be focused To Solve the Problem You can change a lens with CS lens mount to the camera 75 Day Night High definition Dome Camera User Manual Or you can use a C CS adapter ring between the camera and the lens with C lens mount Problem 3 The camera is installed with an auto iris lens You adjust the focus to get a clear image in the daytime but the image is defocused at night Possible Reasons In the daytime the illumination is high so the iris is adjusted to a small size automatically The DOF depth of field is long But at night the iris is adjusted to a large size automatically so the DOF is shortened The focus you adjusted in the daytime now locates out of the DOF so the image is defocused at night To Solve the Problem When you adjust the focus for a camera with an auto iris lens you need to set the lens type to AES auto electronic shutter mode Under AES mode the iris is adjusted to the largest size automatically Then you can adjust the focus to get a clear image At last you need to set the lens type back to
22. de to night day mode when the light condition is up to the switching threshold SHUTTER Steps 1 Move the cursor to SHUTTER and press confirm to select the values OFF 1 120 1 175 1 250 1 500 1 750 1 1K 1 2K 1 4K 1 10K 1 100K are selectable Note The SHUTTER mode is AUTO and not adjustable when the LENS mode is ELC or the WDR is enabled 2 Move the cursor to SLOW SHUTTER and press confirm to select the value OFF x2 x4 x6 x8 x12 x16 x24 x32 x48 x64 x128 x160 x256 x512 Note 56 Day Night High definition Dome Camera User Manual The x2 x4 options accumulate the light by frame unit to lengthen the exposure time 3 Move the cursor to MOTION and press confirm to select the value SLOWER SLOW STD FAST FASTER AGC There are 4 modes selectable for auto gain control OFF HIGH MID or LOW FLICKERLESS This function can avoid the image flicker Move the cursor to FLICKERLESS and press confirm to set it ON or OFF This function is used for PAL standard camera under 60Hz light source and NTSC standard camera under 50Hz Digital WDR Setting Note DS 2CC5187 5197 51A7P N VF doesn t support Digital WDR function Steps 1 Move the cursor to Digital WDR and press confirm to enable or disable this function If the Digital WDR is enabled the parameters below can be configured 57 Day Night High definition Dome Camera User Manual DIGITAL WDR SETUP MOD
23. e adjusting range is from 0 degree to 355 degrees Tilting Lock Screw Panning Table Figure 2 5 Lens Adjustment 21 Day Night High definition Dome Camera User Manual 11 Attach the black liner to the camera 12 Rotate the lower dome clockwise to the camera 13 Remove the protection film softly to complete the installation e eer Ld Clockwise Lower Dome Ceiling Figure 2 6 Lower Dome Installation Note Remove the protection layer after the installation is completed in case of the image problem caused by the scrape of the lower dome 2 2 In ceiling Mounting Without Gang Box Notes 1 Please make sure that the ceiling is strong enough to withstand three times the weight of the camera 2 In ceiling mount is not supplied Steps 22 Day Night High definition Dome Camera User Manual GAIN EE Rotate the lower dome anticlockwise to remove it Remove the black liner Loosen the two screws as shown in Figure 2 7 Remove the white base together with the base plate Set Screw Figure 2 7 Disassembling Attach the drill template supplied to the place where you want to fix the camera Drill two screw holes according to the two circles on the drill template as shown in Figure 2 8 Drill a hole in the ceiling according to the circle in the center of the template It is for in ceiling mounting 23 Day Night High definition Dome Camera User Ma
24. e basic function of the camera However it doesn t mean the listed functions are all supported by this series of cameras Please take the function in the corresponding specification as the standard Definition Definition is the degree to distinguish the edge between two parts clearly Contrast Contrast is the color difference between the brightest and darkest parts Saturation Saturation is the degree of color purity The color is purer the image is brighter DAY NIGHT Auto Switch The cameras deliver color images during the day And as light diminishes at night the cameras switch to night mode and deliver black and white images with high quality AGC AGC is a control circuit that automatically changes the gain of a receiver or other piece of equipment so that the desired output 71 Day Night High definition Dome Camera User Manual signal remains essentially When under low illumination AGC will regulate the gain and amplification of the video signal S N ratio It is the ratio of Signal voltage and noise voltage The ratio is larger the effect of noise is less and the image is clearer White Balance White balance is the white rendition function of the camera to adjust the color temperature according to the environment automatically BLC If you focus on an object against strong backlight the object will be too dark to be seen clearly The BLC Backlight Compensation function can compensate light
25. ess confirm and the day night menu items will be displayed on the screen DAY NIGHT SETUP MODE AUTO V D N LEVEL L 1 H D N DELAY 3s v N D LEVEL L 1 H N D DELAY 35 V IR SWITCH ON Vv RETURN Figure 3 19 Day Night 2 Move the cursor to D N LEVEL and press left right to select the value from Low to High 3 Move the cursor to DN Delay and press up down to select the switch time 1S 3S 5S 10S 20S 25S and 30S are selectable 4 Move the cursor to N D LEVEL and press left right to select the value from Low to High 5 Move the cursor to N D Delay and press up down to select the switch time 1S 3S 5S 10S 20S 25S and 30S are selectable 6 Move the cursor to RETURN and press confirm button to return to the previous menu Notes 55 Day Night High definition Dome Camera User Manual 1 When the IR Switch is on the camera goes to the protection mode if the Day mode switches to Night mode 5 times continuously in 10 minutes The protection mode will last for one hour One hour later the camera will detect the surrounding s light and switch to the day mode if the brightness reaches to the N D LEVEL value 2 AUTO mode means the camera switches between Day and Night modes automatically And when the light condition reaches to the D N N D LEVEL you have set the day and night mode will switch automatically And D N ND Delay means the time from the day night mo
26. ich can be 7 Day Night High definition Dome Camera User Manual determined by turning the eguipment on and off the user is reguired to take measures to eliminate the interference or discontinue the use of this equipment Lead Content Please recycle this device in a responsible Pt 2LI manner Refer to local environmental regulations for proper recycling do not dispose of device in unsorted municipal waste Day Night High definition Dome Camera User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may occur if any of the warnings are neglected Cautions Injury or equipment damage may occur if any of the cautions are neglected A Warnings Follow these Cautions Follow these safeguards to prevent precautions to prevent serious injury or death potential injury or material damage A Warnings Please adopt the power adapter which can meet the safety extra low voltage SELV request And source with DC 12V or AC 24V depending on models according to the IEC60950 1 and Limited Power Source standard e Ifthe product does not work properly please contact your dealer or the nearest service center Never attempt to 9 Day Night High definition Dome Camera User Manual disassemble
27. ion is used to reduce the noise in the video signal Move the cursor to NR and press confirm to enter the NR submenu Y LEVEL The value ranges from 0 to 15 NR YLEVEL l 004 RETURN Figure 3 13 NR 3 1 12 Camera ID Setting From Camera ID submenu you can customize the camera ID It also allows you to adjust the camera ID position on the monitor screen This series of camera supports up to 52 characters Select OFF to disable the Camera ID Select ON to enable the Camera ID Customizing the camera ID Steps 1 Set it to ON and press the menu button to enter the submenu 44 Day Night High definition Dome Camera User Manual 2 Set the menu button up down left right to position the cursor on the character you want 3 Press menu button to confirm your selection The selected character displays on the screen 4 Repeat the steps 1 through 3 to select other characters Modifying the camera ID Steps 1 Position the cursor on one of the arrows lt gt TV 2 Press the menu button to position the cursor on the character that needs to be modified 3 Select one of the other characters to replace it Clearing the camera ID Steps 1 Position the cursor on CLR 2 Press the menu button to clear the characters Positioning the camera ID Steps 1 Move the cursor to POS and press the menu button to enter the position setting interface 2 Set the menu button up down left right to
28. lue values to configure the white balance Manual WB setting is shown below Steps 1 Select MANUAL and the menu will be displayed on the screen 59 Day Night High definition Dome Camera User Manual WHITE BALANCE MODE Manual V TEMP lt gt RETURN Figure 3 21 Manual WB 2 Move the cursor to TEMP and press left right to adjust the temperature value 3 After the settings move the cursor to RETURN and press confirm to return to the previous menu 3D NR You can set the digital noise reduction to ON or OFF The value can be adjusted from 0 to 7 when the function is on SHARPNESS Move the cursor to VALUE and press left right to set the value from 0 to 15 GAIN This feature is used to adjust the brightness from 0 to 7 by pressing left right button 60 Day Night High definition Dome Camera User Manual C GAIN This feature is used to adjust color saturation from 0 to 7 by pressing left right button DEFINITION Move the cursor to DEFINITION and press confirm Press left right to adjust the value from 0 to 7 ANTI SHAKE This feature is suitable for slight shaken scenes Move the cursor to ANTI SHAKE and press confirm to select ON or OFF Note The MOTION DET is disabled when the ANTI SHAKE mode is ON MOTION DET Move the cursor to MOTION DET and press confirm to enter the submenu Move the cursor to MODE and press confirm to select motion detection mode OFF ON
29. ng 15 Camera Reset Setting 16 Defective Pixel Correct Setting sesse 47 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 PLIT Save AVERE OE EE EE AE 47 TT N HO Hi Day Night High definition Dome Camera User Manual 3 2 Menu Description B 148 3 2 1 Menu Overview 48 33252 Ie di RR EE ITTELLEF ETIT TITTET 50 3 2 3 Exposure 50 3 2 4 Funtion 159 SAND System de WE Eg 67 3 2 6 Language ss 70 3 2 7 Exit 70 1 Glossary 71 2 TroubleshoOoting sasarkan SESE RE EE ER EER EES EER AN SERS E RE EE 75 3 Technical Maintenance 77 13 Day Night High definition Dome Camera User Manual 1 Introduction 1 1 Product Features This series of camera adopts high sensitivity sensor and advanced circuit board design technology It possesses of high resolution low distortion and low noise features etc It is extremely suitable for surveillance system and image process system The main features of DS 2CC5181 5191 51A1P N VF are as follows Adopt high performance SONY CCD providing high quality image Color minimum 0 001Lux F1 2 B W minimum 0 0001Lux F1 2 ICR filter auto switch Support OSD menu which enables user to configure the detailed parameters Back Light Compensation BLC with programmable BLC area Auto white balance with high color rendition High Signal Noise Ratio SNR which brings clear and high quality image Auto electronic shutter control to
30. nual Screw Hole Figure 2 8 The Drill Template 8 Rotate the two screws clockwise to the number 2 holes of the in ceiling mount 9 Attach the in ceiling mount to the ceiling 10 Push the two toggle bolts through the two screw holes on the ceiling 11 Rotate the bolt till the toggle holds the ceiling tightly so that the in ceiling mount is fixed to the ceiling SERRE LEE eili BR TR eiling ES Mount i l Toggle Bolt In ceiling Figure 2 9 In ceiling Mount 24 Day Night High definition Dome Camera User Manual 12 Route the cables through the hole in the center of the in ceiling mount 13 Secure the camera with two screws as shown in Figure 2 10 Figure 2 10 Securing the Camera 14 Connect the video output connector to the monitor Connect the power connector to the power supply 15 Three axis adjustment 1 2 3 4 5 View the camera image using the monitor Rotate the panning table to adjust the panning position of the camera The adjusting range is from 0 degree to 355 degrees Loosen the tilting lock screw Rotate the tilting table to adjust the tilting position of the camera The adjusting range is from 0 degree to 180 degrees Tighten the tilting lock screw 25 Day Night High definition Dome Camera User Manual 6 Rotate the lens to adjust the azimuth angle of the image The adjusting
31. ome Camera User Manual set the different shutter and AGC value according to the luminance level of the situation You can choose MANUAL and AUTO mode for the shutter and AGC Note On the lens setting interface if you choose lens type as AUTO the AUTO IRIS can also be adjusted to change the brightness of the image otherwise only shutter and AGC are adjustable MANUAL SETUP MODE SHUT AGC SHUTTER 1 50 AGC 6 00 RETURN Figure 3 2 MANUAL SETUP In the MANUAL SETUP submenu you can adjust the SHUTTER speed and AGC value to maintain the brightness level of the camera SHUTTER Manually set the shutter speed 1 50 1 120 1 250 1 500 1 1k 1 2k 1 4k and 1 10k are selectable AGC The AGC value can be set between 6 and 44 8 31 Day Night High definition Dome Camera User Manual AUTO SETUP HIGH LUMINANCE MODE SHUT AUTO IRIS AUTO IRIS BRIGHTNESS 080 LOW LUMINANCE MODE AGC BRIGHTNESS X0 50 RETURN Figure 3 3 AUTO SETUP In the AUTO SETUP submenu Figure 3 3 you can adjust the BRIGHTNESS value The system will automatically adjust the SHUTTER AGC and AUTO IRIS settings according to the BRIGHTNESS value And the system can define and recognize the luminance level automatically In HIGH LUMINANCE condition the SHUTTER speed and AUTO IRIS level is modified automatically according to the BRIGHTNESS value MODE SHUT AUTO IRIS and AUTO IRIS are available when the LENS type i
32. r dome of the camera anticlockwise to take it down from the camera and remove the black liner Black Liner White Base Figure 2 2 Black Liner Disassembling 19 Day Night High definition Dome Camera User Manual 5 Attach the base plate to the ceiling and secure it with the supplied 4 self tapping screws as shown in Figure 2 3 Note Please use expansion screws if the dome camera is mounted to cement wall Ceiling j Base Plate Screws Figure 2 3 Mounting the Base Plate 6 Route the cables through the cable hole 7 Align the camera with the base plate Rotate the camera clockwise into the base plate 8 Tighten the lock screw to secure the camera with the base plate as shown in Figure 2 4 Base Plate Camera Figure 2 4 Securing the Camera 20 Day Night High definition Dome Camera User Manual Connect the video output connector to the monitor Connect the power connector to the power supply 10 Three axis adjustment 1 2 3 4 5 6 View the camera image via the monitor Rotate the panning table to adjust the panning position of the camera The adjusting range is from 0 degree to 355 degrees Loosen the tilting lock screw Rotate the tilting table to adjust the tilting position of the camera The adjusting range is from 0 degree to 180 degrees Tighten the tilting lock screw Rotate the lens to adjust the azimuth angle of the image Th
33. range is from 0 degree to 355 degrees Tilting Lock Screw Panning Table Figure 2 11 Lens Adjustment 16 Attach the black liner to the camera 17 Rotate the lower dome clockwise back to the camera Figure 2 12 Lower Dome Installation 26 Day Night High definition Dome Camera User Manual Note Remove the protection film softly after the installation is completed in case of the image problem caused by the scrape of the lower dome 2 3 Wiring i Figure 2 13 The Power and the Video cable Notes 1 Please make sure that the power adapter can match with the camera 2 The standard power supply of the camera is 12V DC or 24 AC Please refer to technical specifications for more details 27 Day Night High definition Dome Camera User Manual 3 Menu Operations 3 1 Menu Description A Note The menu described in this chapter is applicable to DS 2CC5181 5191 51A1P N VF 3 1 1 Menu Overview This series of camera supports OSD menu operation and the menu is listed below LENS AUTO MANUAL SHUTTER AGC SHUT AUTO IRIS AUTO IRIS SHUT AGC WHITE BAL ATW PUSH PUSH LOCK USER1 USER2 ANTICR MANUAL Main BACKLIGHT BLC HLC Menu PICT ADJUST MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE GAIN ATR LUMINANCE CONTRAST MOTION DET DETECT SENSE BLOCK DISP MONITOR AREA AREA SEL PRIVACY AREA SEL COLOR TRANSP 28
34. ratch or image blur Please refer to the following method to clean the bubble e Handling dust Use oil free soft brush or blowing dust ball to clean the dust e Handling oil Steps 1 Wipe off the water drop or oil by soft cloth and dry the bubble 2 Use oil free cotton cloth or bubble clean paper to wipe the bubble from center to outside with alcohol or detergent 3 Change the cloth to wipe the bubble until the bubble is clean Glass Maintenance of IR Camera Steps 1 Wipe off the dust water drop or oil by soft cloth and dry the glass 2 Use oil free cotton cloth or glass clean paper to wipe the glass from center to outside with alcohol or detergent 3 Change the cloth to wipe the glass until the glass is clean 78 First Choice for Security Professionals Hikvision Digital Technology Co Ltd All Rights Reserved
35. rent mounting reguirements 1 2 Overview Figure 1 1 Overview 16 Day Night High definition Dome Camera User Manual 1 Lower Dome 6 Menu Button 2 Black Liner 7 AUX Interface 3 Lens Cover 8 Len Adjust Lever 4 Camera 9 Tilt Lock Screw 5 Base Plate 17 Day Night High definition Dome Camera User Manual 2 Installation Before you start Please make sure that the device in the package is in good condition and all the assembly parts are included This series of camera support several mounting methods like ceiling mounting in ceiling mounting with a gang box in ceiling mounting without a gang box and wall mounting We will take ceiling mounting and in ceiling mounting without a gang box as the examples in this chapter 2 1 Ceiling Mounting Note Please make sure that the ceiling is strong enough to withstand three times the weight of the camera Steps 1 Attach the drill template supplied to the place where you want to fix the camera 2 Drill four screws holes according to the number 2 circles on the drill template as shown in Figure 2 1 18 Day Night High definition Dome Camera User Manual oN Figure 2 1 The Drill Template 3 Drilla hole in the ceiling according to the circle in the center of the template if you want to route the cables through the ceiling Skip this step if you want to route the cables on the surface of the ceiling 4 Rotate the lowe
36. ress and hold the menu button to left for about 2 seconds to enable auto DPC function Note DPC will be more active in the absolutely dark environment Make sure that the lens s IRIS is closed before using this function 3 1 17 Save All Exit Move the cursor to the Exit and press the menu button to exit the settings without saving Move the cursor to SAVE ALL and press menu button to save the settings and exit 47 Day Night High definition Dome Camera User Manual 3 2 Menu Description B Note The menu described in this chapter is applicable to DS 2CC5183 5193 51A3P VF DS 2CC5185 5195 51A5P N VF and DS 2CC5187 5197 51A7P N VF 3 2 1 Menu Overview This series of camera supports OSD The menu tree is listed below 48 Day Night High definition Dome Camera User Manual MAIN MENU T T T T 1 SCENE EXPOSURE FUNCTION SYSTEM LANGUAGE EXIT T I I NoboR LENS SYNC CAMERA ID IN za WHITE SYSTEM BACK HIGHT i BALANCE mi CAMERA Mass CURE ne RESET Low SHARPNES LUMINANCE pales IRSTD AGC Y GAIN I i I CUSTOMIZE FLICKERLESS C GAIN DIGITAL I WDR DEFINITION I SMART IR antr SHAKE MOTION DET PRIVACY MASK pIGtTAL on dis MIRROR enfer ORREL HLC I IRS ADJUST Figure 3 15 Main Menu Overview Note This series of camera adopts joystick control You can select the menu item by setting the joystick which is beside the lens to up down left right 49 Day Night High definition Dome Camera
37. rsonel Power Supply Hazardous Voltage AC mains voltages are present within the power supply assembly This device must be connected to a UL approved completely enclosed power supply of the proper rated voltage and current No user serviceable parts inside the power supply AN WARNING System Grounding Earthing To avoid shock ensure that all AC wiring is not exposed and that the earth grounding is 5 Day Night High definition Dome Camera User Manual maintained Ensure that any equipment to which this device will be attached is also connected to properly wired grounded receptacles and are approved medical devices Power Connect and Disconnect The AC power supply cord is the main disconnect device to mains AC power The socket outlet shall be installed near the equipment and shall be readily accessible Installation and Maintenance Do not connect disconnect any cables to or perform installation maintenance on this device during an electrical storm Al WARNING Power Cord Requirements The connector that plugs into the wall outlet must be a grounding type male plug designed for use in your region It must have certification marks showing certification by an agency in your region The connector that plugs into the AC receptacle on the power supply must be an IEC 320 sheet C13 female connector See the following website for more information http kropla com electric2 htm Lithium Batte
38. ry This device contains a Lithium Battery There is a risk of explosion if the battery is replaced by an incorrect type Day Night High definition Dome Camera User Manual Dispose of used batteries according to the vendor s instructions and in accordance with local environmental regulations Perchlorate Material Special handling may apply See www dtsc ca gov hazardouswaste perchlorate This notice is reguired by California Code of Regulations Title 22 Division 4 5 Chapter 33 Best Management Practices for Perchlorate Materials This device includes a battery which contains perchlorate material Taiwan battery recycling CF Please recycle batteries Thermal and Mechanical Injury Some components such as heat sinks power regulators and processors may be hot care should be taken to avoid contact with these components Electro Magnetic Interference This equipment has not been tested for compliance with emissions limits of FCC and similar international regulations This device is not and may not be offered for sale or lease or sold or leased until authorization from the United States FCC or its equivalent in other countries has been obtained Use of this equipment in a residential location is prohibited This equipment generates uses and can radiate radio frequency energy which may result in harmful interference to radio communications If this equipment does cause harmful interference to radio or television reception wh
39. s AUTO IRIS When the LENS type is Manual the iris is fixed and only SHUT option is provided BRIGHTNESS The value ranges from 0 to 255 32 Day Night High definition Dome Camera User Manual In LOW LUMINANCE condition the AGC can be adjusted automatically according to the BRIGHTNESS value MODE Only AGC is available BRIGHTNESS x1 00 x0 75 x0 50 and x0 25 are selectable 3 1 4 White Balance Setting Move the cursor to the White Balance and select ATW PUSH PUSH LOCK USER1 USER2 ANTI CR and MANUAL by pressing the left right button e ATW Auto Tracking White Balance In ATW mode white balance is continuously being adjusted in real time according to the color temperature of the scene illumination SPEED The speed can be set from 0 to 255 DELAY CNT It s the response time when the color temperature changes ATW FRAME It s used to adjust the image size of the ATW image 33 Day Night High definition Dome Camera User Manual ENVIRONMENT INDOOR and OUTDOOR are selectable ATW SPEED DELAY CNT i ATW FRAME x1 00 ENVIRONMENT INDOOR RETURN Figure 3 4 ATW USER 1 USER2 USER 1 is the indoor mode and it is suitable for the indoor environment B Gain and R Gain are adjustab e USER 2 is suitable for the fluorescent light environment B Gain and R Gain are adjustable USERI WB B GAIN 030 R GAIN 033 RETURN Figure 3 5 USER 1 WB 34
40. to the object in the front to make it clear but this causes the over exposure of the background where the light is strong SMART IR The SMART IR adopts the smart image processing technique to automatically adjust the brightness curve by detecting multi zone brightness and so as to prevent the over exposure of central point existed in short IR distance conditions Motion Detection In the user defined motion detection surveillance area the moving object can be detected and trigger alarm The sensitive level can be customized according to the environment Privacy Mask 72 Day Night High definition Dome Camera User Manual This function allows you to block or mask certain area of a scene thus prevent the personal privacy from recording or live viewing OSD On Screen Display OSD is the texts superimposed on a screen It can show the menu on the screen Synchronous System Synchronization of the camera usually contains power synchronization and internal synchronization Internal synchronization is realized by the synchronous signal which is generated by the inside crystal oscillator ICR Auto Switch The filter will filter infrared light during the daytime and change to normal filter at night to ensure a high sensitivity and clear image WDR Wide Dynamic Range The wide dynamic range WDR function helps the camera provide clear images even under back light circumstances When there are both very bright and very dark
41. tton to exit the area setting page Note Type 1 4 adjustable windows Type 2 Full screen Type 3 12 x 8 windows by default Pressing confirm can cancel a window and press confirm twice to select a window PRIVACY MASK Move the cursor to PRIVACY MASK and press confirm to set it ON The menu will appear on the screen PRIVACY MASK SETUP MODE ON V AREA SEL al V ON OFF OFF V POSITION COLOR MOSAIC v RETURN Figure 3 23 Privacy Mask 63 Day Night High definition Dome Camera User Manual Move the cursor to AREA SEL and press confirm to select the privacy mask area And there are 12 zones in total Move the cursor to ON OFF and press confirm to select ON Then define the size and position of the privacy mask area according to the step 1 to step 3 Steps 1 Move the cursor to POSITION and press confirm to define the size and position of mask area Then press confirm to exit 2 Move the cursor to COLOR 8 colors are selectable Move the cursor to MOSAIC and press confirm button to select ON or OFF MOSAIC means that the privacy mask will be mosaic 3 Repeat the above operation to define other mask areas 4 Move the cursor to RETURN and press confirm to return to the previous menu DIGITAL ZOOM Move the cursor to DIGITAL ZOOM and press confirm The menu will appear on the screen DIGITAL ZOOM RATIO OFF X2 xa x8 X16 Figure 3 24 Digital Zoom 64 Day Night
42. u Position the cursor on VALUE Set the menu button left right to choose a value The value ranges from 0 to 15 Move the cursor to RETURN and press the menu button to return to the previous menu LENS SETUP LENS ALCV VALUE 007 RETURN Figure 3 16 LENS SETUP 51 Day Night High definition Dome Camera User Manual BLC WDR SETUP Back Light Compensation Wide Dynamic Range e BACK LIGHT COMPENSATION Purpose If there s a strong backlight the object in front of the backlight appears silhouetted or dark BLC can correct the exposure of the subject But the backlight environment is overexposed Steps 1 Move the cursor to BLC WDR and press the menu button to enter the BLC WDR menu 2 Position the cursor on the BLC and press the menu button to enter the BLC settings menu 3 You can set the AREA and the brightness VALUE of BLC in this menu e The AREA can be set to UP DOWN LEFT RIGHT CENTER CUSTOMIZE When you select CUSTOMIZE the SIZE and POSITION menu items will display under the AREA item You can adjust the size and position of the BLC area under customize mode e The VALUE ranges from 0 to 15 The larger the value is the brighter the object is in front of the backlight 4 Move the cursor to RETURN and press the menu button to return to the previous menu 52 Day Night High definition Dome Camera User Manual BLC WDR SETUP MODE BLCV AREA CUSTOMIZE Vv SIZE EN
43. ubmenu MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE and GAIN are adjustable MIRROR If you turn the MIRROR function on the image will be flipped horizontally It is like the image in the mirror BRIGHTNESS The brightness is adjustable from 0 to 255 CONTRAST This feature enhances the difference in color and light between parts of an image The value ranges from 0 to 255 SHARPNESS 36 Day Night High definition Dome Camera User Manual SHARPNESS describes the clarity of detail in the image The value ranges from 0 to 255 e HUE Adjust this feature to change the color of the image The value ranges from 0 to 255 GAIN Adjust this feature to change the depth of the color The value ranges from 0 to 255 PICT ADJUST MIRROR BRIGHTNESS CONTRAST SHARPNESS HUE GAIN RETURN Figure 3 7 PICT ADJUST 3 1 7 ATR Setting ATR is the digital dynamic range function which can adjust the brightness and contrast level of the image and balance the brightness level of the whole image 37 Day Night High definition Dome Camera User Manual Move the cursor to ATR Set the button left right to select ON or OFF After you set it to ON press the confirm button to enter the ATR submenu LUMINANCE MID HIGH and LOW are selectable standing for middle high and low luminance respectively CONTRAST MID HIGH LOW MIDLOW and MIDHIGH are selectable ATR LUMINANCE LOW CONTRAST
44. values And after you set all this value you can see a frame on the image 6 Return to the MAIN MENU and click SAVE ALL 7 You can find the MONITOR AREA frame take effect after you exit the main menu Note The MONITOR AREA frame takes effect only when there are BLOCK DISP panes in the MONITOR AREA frame MOTION DET DETECT SENSE 111 BLOCK DISP OFF MONITOR AREA ON AREA SEL 14 TOP BUTTOM LEFT RIGHT RETURN Figure 3 9 MOTION DET 3 1 9 Privacy Mask Setting This feature allows you to cover certain areas which you don t want to be viewed or recorded Up to 8 privacy areas are configurable Steps 1 Move the cursor to PRIVACY and press confirm to enter the PRIVACY submenu 40 Day Night High definition Dome Camera User Manual 2 Select one privacy area in AREA SEL 3 Set the values of TOP BOTTOM LEFT and RIGHT The size and the position of the area can be defined by these values 4 Select the color and the transparency values for the privacy area Turn the MOSAIC on if you want to mosaic the privacy areas 5 Repeat the steps 1 to step 4 to configure other privacy areas AREA SEL COLOR TRANSP Note There are 8 areas available There are 8 colors available The available values are 1 00 0 75 0 50 and 0 00 PRIVACY AREA SEL US TOP BUTTOM LEFT RIGHT COLOR TRANSP 0 00 MOSAIC OFF RETURN Figure 3 10 PRIVACY When the motion
Download Pdf Manuals
Related Search