324W LED Moving Head Wash IW108
Contents
1. 4 K 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the device Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety rope through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw 5 DMX 512 control connections Connect the provided XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX output DMX Input 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground 2 Signal 3 Signal NN 120 Ohms lt DMX512 OO DMX controller Address 26 Address13 Address 1 DMX 512 connection with DMX terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connect2. Ww VJ 324W LED Moving Head Wash IW108 RGBW User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for choosing Dialighting s 324W LED moving head wash For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs Dialighting s moving wash is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos IW108 RGBW adopts powerful LED lamps which features high brightness and stability Please carefully dispack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head one Signal Cable one Omega Clamp one User Manual one Power Cable one Safety Chain one 10 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices
3. allation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualified personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies It is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 8 Technical Specifications Input Voltage AC90 260V 50 60Hz LED Quantities 24 red 28 green 28 blue 28 white Edison LEDs 3W Control Signal DMX512 master slave and sound activated or auto operation Control Channel 13 DMX Channels Power Consumption 324W Dimensions 350x260x350mm Packing Dimensions 430x300x400mm Net Weight 10 5kg Gross Weight 11 5kg 7 DMX Channels l s ma ee Green 0 Black 255 100 Green 7 Blue 0 Black 255 100 Blue White 0 Black 255 100 White Strobe Rainbow 10 i Reset ee internal amp N 4 Installation via Clamp Please refer to the picture below i A i SS
4. cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for smooth air flow so there should be no shelter for fans and ventilation for heat radiation If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard 3 Operation Instructions The moving head is an LED wash light for onsite decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the inst
5. ed between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1202 PIN 3 PIN 2 6 Operation Menu Te ee RET Ri B gt press menu to back Pan Tat Horizon YES OR EI press menu to back Enter up down Pan angle 540 630 Tilt invertor aat YES orng press menu to back mode DMX 512 rN press menu to hack Enter TEA gt press menu to back Enter press menu to back Tit e press menu to back NTE top _ press menu to back auto mode Enter up down Enter up down Date xxx Choose channal Number of controlled Enter Manually operate Enter Enter Allthe motor reset Restore Enter All the data change to original The display will close after 30 seconds without operations
6. openingim Beam opening m Beam opening Beam opaningm gt dont _ v Distanceirmn 2 Safety Instructions CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual ZS Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch iton immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person The device shall only be used with rate voltage and frequency Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before
7. or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling Suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed a gt CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer Photometric Data Red color Ream
Download Pdf Manuals
Related Search