300 amp battery jumper with 260psi air compressor
Contents
1. short circuit that may cause severe burns Never charge or jump start a frozen battery Never allow clamps positive amp negative terminals to touch together or to connect the same piece of metal to prevent short circuits and arcing Do not operate this device while wearing vinyl clothing Static electricity may be generated when vinyl clothing is rubbed This product is not intended for use in the rain or temperatures above 130 f Use only the provided chargers cables and clamps Unauthorized parts may damage the unit This product has no consumer serviceable parts This product is not a toy Keep out of the reach of children Keep battery terminals clean Be careful to keep corrosion from coming in contact with eyes Do not let the cords of the jump starter or attached appliances get wet Do not operate this unit in or around water Water can damage the unit CHARGING AND RECHARGING WARNING Do not overcharge this unit Prior to charging unit read and understand all instructions for this unit Overcharging may result in damage to the unit All rechargeable batteries gradually discharge when left idle and you need to recharge them periodically to maintain maximum battery capacity The AC charger supplied with the Power Station is designed to charge using a 230 240 volt outlet Using the DC charging cable the Power Station can be recharged while you drive your vehicle e To ensure safe recharging and maximum battery life recharge the Po2. D GCG S Ss Model No DPS300 300 AMP BATTERY UPER WIH260PS AIR GCOMPRESSCR High Impact Resistant Rubberized Housing 300 AMP Jump Start System 260 PSI Air Compressor 12 Volt Power Station WELCOME This product has been carefully engineered and manufactured to give you dependable operation Please read this manual thoroughly before operating your new product as it contains the information you need to become familiar with its features and obtain the performance that will bring you continued enjoyment for many years Please keep this manual on file for future reference IMPORTANT PRIOR TO USE READ AND UNDERSTAND ALL WARNINGS CAUTIONS AND INSTRUCTIONS INCLUDED IN THIS INSTRUCTION MANUAL AND THOSE PUBLISHED BY YOUR VEHICLE BATTERY MANUFACTURER AND MANUFACTURER OF ANY DEVICE INTENDED TO BE USED WITH THIS UNIT RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE LOCATION OF CONTROLS 2 1 12 volt DC Power Socket 2 Rubberized handle 1 3 Jump Starter ON OFF Switch 4 Battery Indicator LEDs 5 Power Polarity Indicator 6 7 8 p gt ew FF Me nae yh Charging Indicator Charging Jack 4 Battery Status Button 9 Heavy Duty Jumper Cables 10 Battery Cable Clamp Storage Posts 11 Air Inflation Hose Storage Slot 12 Air Compressor ON OFF Switch 13 Air Compressor Gauge 14 Air Inflation Hose 15 DC Charging Cable 16 Air Inflation Nozzles 17 AC Charger FIRST AID Make sure fresh water and soap are avail
3. able nearby in case battery acid contacts skin eyes or clothing If contact with battery acid occurs rinse immediately and thoroughly with water Then wash with soap and water Obtain immediate medical attention if redness irritation or pain is present For eye contact flush eyes for at least 15 minutes and obtain immediate medical attention CAUTIONS e Never work alone with this product Make sure that someone is available to give assistance if needed Wear complete eye and clothing protection Do not touch eyes while working near battery Always keep the clamps in their storage covers to prevent sparking when they are not in use Do not recharge product battery with damaged chargers Replace chargers immediately Do not attempt to remove or replace the battery used in this device When the battery has reached the end of it s useful lifetime take the entire unit to a battery recycling facility e Avoid dropping metal tools onto vehicle battery It may spark or short circuit the battery or other electrical part that may cause short circuits or explosion e For proper and safe operation of the 12 Volt DC power accessory outlets do not place anything into it except the plug of the accessory to be used Do not place anything into AC charging input socket except the provided plug from charger unit Remove metal personal jewelry such as rings bracelets necklaces and watches while working with a lead acid battery It can produce a
4. e OFF position Remove the charging jack cover and insert the AC charger cable into the charging jack located on the front panel Plug the AC charger into a standard AC wall outlet While the Power Station is recharging the red LED charging indicator will be lit A typical recharge time is 20 to 24 hours During the charging period you can press and hold the battery status button to check the Power Station battery charge level The red LED then the yellow LED and finally the two green LEDs will illuminate sequentially during the charging process Continue charging until the two green LEDs remain lit constantly Disconnect the AC charger after the Power Station is fully charged CHARGING WITH 12 VOLT CHARGER DO NOT EXCEED MAXIMUM RECOMMENDED AC CHARGE OF 18 HOURS 1 Disconnect any DC appliance from the 12 volt DC power socket 2 Turn the jump starter ON OFF switch to the OFF position 3 Plug the DC charger cable into any standard 12 volt cigarette lighter accessory socket Sy Sa ee oh 2 4 Remove the charging jack cover and insert the DC charger cable into the charging jack located on the front panel 5 While the Power Station is recharging the red LED charging indicator will be lit A typical recharge time is 8 to 12 hours 6 During the charging period you can press and hold the battery status button to check the Power Station battery charge level The red LED then the yellow LED and finally the two green LEDs will illuminate sequ
5. entially during the charging process Continue charging until the two green LEDs remain lit constantly Disconnect the DC charger cable after the Power Station is fully charged JUMP STARTING A VEHICLE WARNING Vehicles equipped with on board computers may be affected if the engine battery is jump started Read your vehicle owner s manual before attempting to start the vehicle to determine if external starting assistance can be used Failure to follow these instructions may cause damage or explosion Use safety glasses to protect eyes while jump starting a battery Turn off the vehicle ignition and all accessories e g radios lights air conditioners and cellular phones Set the emergency brake and put vehicles with automatic transmission in park position Make sure the Jump Start System Power Switch is in OFF position Determine the polarity of the vehicle s battery terminals The positive POS P battery terminal usually is larger in diameter than the negative NEG N terminal If you are unsure you should refer to the vehicle s owner s manual 5 Determine whether your vehicle uses a negative or positive grounded system Negative ground system Negative battery terminal is grounded to chassis Most vehicles use this system Positive grounded battery terminal is grounded to chassis or any other part of the vehicle If you are unsure you should refer to vehicle owner s manual 6 Never allow clamps positive amp negat
6. igarette lighter ac cessory socket OPERATING A DC DEVICE 1 Remove the protective cover from the DC power socket 2 Plug the 12 volt DC appliance into the power socket then turn the appliance on if required If the appliance draws more than 10 amps or has a short circuit defect the internal circuit breaker of the Power Station shuts off the power to the appliance If this occurs unplug the appliance The internal circuit breaker automatically resets after a few seconds 3 Fully recharge the Power Station as soon as possible after each use As the DC power socket is internally wired directly to the Power Station s battery extended operation of a 12 volt DC appliance may result in excessive battery discharge STORAGE This unit may be stored in any position Make sure the clamps are secure inside the booster cable storage covers Store at room temperature If not used for a prolonged period of time recharge every 2 months in the winter and every month in the summer SPECIFICATIONS Battery 12 Volt 8AH sealed lead acid maintenance free spill proof rechargeable Power Supply DC Output 12 volts nominal Air Compressor 260 PSI Power Supply Charging Time 28 hours with AC charger 8 hours to recharge with Storage Temperature Store in a cool dry area
7. ist holding the unit securely in place during the next steps 11 Turn on the vehicle to attempt to start the engine If the vehicle does not start after 4 to 5 seconds of engine cranking then stop Wait 3 to 4 minutes and then try again Repeat several times until the vehicle starts CAUTION Excessive engine cranking can damage vehicle starter motor If the engine turns but fails to start after several attempts other technical problems might be involved Discontinue cranking the engine until the other problem is determined and corrected 12 Standing as far away from the vehicle battery as is practical disconnect the clamps in reverse sequence to connecting procedure For negative grounded systems first disconnect negative black then positive red clamps For positive grounded systems first disconnect positive red then negative black clamps 3 USING THE AIR COMPRESSOR WARNING Check item to be inflated for manufacturer s maximum recommended inflation pressure Avoid over inflation Most tires are properly inflated between 24 35 PSI Some truck and bicycle tires require 40 PSI or more To inflate tires 1 Remove valve cap from air valve stem Note Make sure locking thumb lever is at up position If necessary use valve stem adapter 2 Insert stem connector to valve stem Make sure connector is pushed to valve stem as far as possible 3 Press down the locking thumb lever to engage 4 Set the compressor on off sw
8. itch to on position by pressing down the section of switch marked Note In the event that the tire is completely flat raise the vehicle using a recommended jack before inflating the tire 5 Monitor pressure on air pressure gauge 6 When desired pressure is reached turn off compressor Turn the locking thumb lever to up position and remove stem connector from valve stem Also remove valve stem adapter if applicable 7 Replace valve cap on valve stem di To inflate plastic inflatable balls air mattresses rubber rafts etc 1 Check manufacturer s specification on item to be inflated for correct inflation pressure 2 Remove valve cap cover from valve stem 3 Insert proper valve stem adapter into stem connector as far as possible and turn the locking thumb lever to down position 4 Insert other end of valve stem adapter into inflatable air valve stem as far as practical 5 Set the compressor on off switch to on position 6 Monitor pressure on air pressure gauge When desired pressure is reached turn off compressor turn the locking thumb lever to up position and remove stem connector from valve stem Also remove valve stem adapter if applicable Replace valve cap on valve stem DC POWER SOCKET OPERATION This Power Station is equipped with a 12 volt DC power socket It can operate 12 volt DC automobile RV marine or other portable appliances that draw less than 10 amps from a 12 volt DC power socket or from a vehicle s c
9. ive terminals to touch together or to contact the same piece of metal to prevent short circuits and arcing 7 Follow instructions for a negative grounded system or positive grounded system as indicated below Negative Grounded System a Securely connect the positive red clamp to the positive POS P terminal of the vehicle battery or the remote positive terminal if equipped b Securely connect the negative black clamp to the vehicle chassis engine block or a non moving metal part of the vehicle which is verified to be grounded Do not clamp directly to negative battery terminal carburetor fuel lines or sheet metal body parts c See jump starting step 7 to continue Positive Grounded System a Securely connect the negative black clamp to the negative Neg N ungrounded terminal of the vehicle battery b Securely connect the positive red clamp to the vehicle chassis engine block or a non moving metal part of the vehicle which is verified to be grounded Do not clamp directly to positive battery terminal carburetor fuel lines or sheet metal body parts c See jump starting step 7 to continue 8 The Reverse Polarity Indicator on the Jump Starter will illuminate RED for wrong connection and GREEN for right connection 9 When correct clamp connection is made turn the Jump Start System Power Switch to ON position 10 Allow 2 or 3 minutes of charging time It is recommended to have a second person to ass
10. wer Station only with the supplied charger or charging cable or equivalent e Fully charge unit with the supplied 230 240 volt AC charger to the recommended maximum and initial charge time of 28 hours Thereafter an AC typical charge time is 20 to 24 hours when using the AC charger e Recharge the unit fully after each use This will prolong the life of the battery because frequent discharges between recharges will reduce battery life e Make sure all functions of the Power Station are turned off during recharging Due to inherent self discharge lead acid batteries should be charged at least every 3 months especially in a warm environment Leaving a battery in a discharged state or if not recharged every 3 months may result in permanent battery damage and poor jump starting performance Do not attempt to recharge the Power Station battery if it is frozen Gradually warm the frozen battery to 0 C 32 F before recharging Do not operate DC appliances with the Power Station while the unit is being recharged with the AC charger The AC charger may be permanently damaged if 12 volt DC appliances are operated while the AC charger is connected NOTE Make sure both cable clamps positive and negative are placed in their storage holsters when not in use CHARGING WITH AC CHARGER DO NOT EXCEED MAXIMUM RECOMMENDED AC CHARGE OF 36 HOURS 1 Disconnect any DC appliance from the 12 volt DC power socket Turn the jump starter ON OFF switch to th
Download Pdf Manuals
Related Search