GBK and GFK Series
Contents
1. 38 Page Adam Eguipment Company 2011 11 1 INPUT COMMANDS FORMAT The scale can be controlled with the following commands Press the Enter key of the PC after each command T lt cr gt lt lf gt Tares the scale to display the net weight This is the same as pressing Tare Z lt cr gt lt lf gt Sets the zero point for all subsequent weighing The display shows zero P lt cr gt lt lf gt Prints the results to a PC or printer using the RS 232 interface It also adds the value to the accumulation memory if the accumulation function is not set to automatic 39 Page Adam Eguipment Company 2011 12 CALIBRATION The GBK GFK scales can be calibrated using kilogram weights or using pounds weights depending on the weighing unit selected at the time of calibration To start the calibration either get into the calibration section through the Scale Settings FUnG 3 see Section 13 3 or turn the scale off and switch on again then press Tare during the self test Enter code number 0000 and press Tare This will take you directly to the calibration section The display will show UnLoAd Remove all weight from the platform and then press the Tare key when the display is stable After the Zero point is set the display will show Lal XX Place the suggested calibration mass on the platform It is best to use a weight close to the full capacity of the scale If the mass is diffe2. x 33 8 Net Weight 12 5kg 27 6 Lb 12 5kg 27 6 Lb 12 5kg 27 6 Lb 25 5 kg 56 2 Lb 12 5kg 27 6 Lb 12 5kg 27 6 Lb Features Weighing Counting Checkweighing with LED lights Percentage Hold function RS232 5 Page Adam Equipment Company 2011 GBK M Models Model GBK 6M GBK 15M GBK 30M GBK 60M GBK 150M Maximum 6kg 15kg 30kg 60kg 150kg Capacity Readability 0 002kg 0 005kg 0 01kg 0 02kg 0 05kg Units of Measure Kilograms only Stabilization 3 2 3 Secs Time Operating 10 C to 40 C 14 F to 104 F Temperature Power Supply 230VAC 50 60Hz Calibration External Calibration Mass User Selectable Display Backlit Green display 25mm with capacity tracker X Cast Aluminum base Pantone cool grey painted base stainless steel grade 304 Top pan ABS Cool grey indicator Balance Housing housing Pan Size 300mm x 400mm 11 8 x 15 7 Overal Dimensions 300mm x 620mm x 860mm 11 8 x 24 4 x 33 8 wxdxh Net Weight 7 6kg 16 8 Lb Features Weighing Counting Checkweighing with LED lights Percentage Hold function RS232 6 Page Adam Eguipment Company 2011 GFK M Models Model GFK 60M GFK 150M GFK 300M Maximum Capacity 60kg 150kg 300kg Readability 0 02kg 0 05kg 0 1kg Units of Measure Kilograms only Stabilization Time 2 3 Secs 2 3 Secs 2 3 Secs Operating Temperature 10 C to 40 C 14 F
3. range of the zero Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing F9 LOW VOLTAGE DETECTION This parameter allows detection of low voltage when the battery wears down To enter this parameter press the Tare key when F9 LU is shown The display will show if the LVD Mode is set to on or oFF Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing F10 CALIBRATION COUNT GK M Only This parameter allows the calibration and parameter counting function to be active To enter this parameter press the Tare key when F10 Gm is shown The display will show if the Calibration Counting Mode is set to on or oFF If On the Calibration count and Parameter count will be seen at power on as described in section 6 0 If set to Off the only method that can be used for access to the calibration or parameters is to place the jumper on pins 1 2 of J1 See section 15 2 Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing 55 Page Adam Equipment Company 2011 F10 AUTO ZERO RANGE Not available on GK M This parameter set the range the autozero is active within To enter this parameter press the Tare key when F10 AZ is shown The display will show the current setting 0 5d 1d 2d or 5d Press the Func key to ch
4. English French German Spanish Enter using numeric keys Enter using numeric keys 60 Page S1 Un Units enable S2 bL Backlight S3 AoF Set Auto off time min S4 dt Set time and date S5 dis Display mode S6 Fi Set Filter S7 SPS Scale password S8 CAL kg Ib EL ott ELon EL AU Auto SLP 0 SLP 1 SLP 5 SLP 10 Set as described in manual All StAb only when stable SLoW nor normal FASt Enter using numeric keys Perform calibration F4 Pct Percent Weighing F4 Ani Animal weighing Enter 100 reference weight FLt1 Filter setting To FLt 5 Adam Eguipment Company 2011 61 Page Adam Equipment Company 2011 62 Page Adam Eguipment Company 2011 Intl Tel EH ADAM Adam Equipment ADAM EQUIPMENT BOND AVENUE DENBIGH EAST INDUSTRIAL ESTATE MILTON KEYNES MK1 1SW U K Fax 01908 641339 Tel 01908 274545 44 1908 274545 Intl Fax 44 1908 641339 E Mail Address info Adamequipment co uk CE Declaration of Conformity Konformit tserkl rung D claration de Conformit Verklaring van overeenstemming Dichiarazione di Conformit Declaraci n de Conformidad The non automatic weighing instrument Die nicht automatischen W geapparate Linstrument de pesage 3 fonctionnement non automatigue Het niet automatische weegwerktuig Strumento per pesatura non automatico Imstrumento para pesaje non
5. 16 REPLACEMENT PARTS AND ACCESSORIES 57 17 SERVICE INFORMATION eo dn r dk la iu n vi 58 18 WARRANTY INFORMATION eee eee eee eee eee 59 19 APPENDIX ne ensure a zoo nana ar ri 60 1 page Adam Equipment Company 2011 2 page Adam Equipment Company 2011 INTRODUCTION The GBK GFK scales provides an accurate fast and versatile general purpose weighing scales with parts counting percent weighing and check weighing functions The GBK GFK has LEDs to indicate when a weight is below the low limit between the limits or above the high limit next to the display These can work in conjunction with an audible alarm for check weighing as well as LCD showing LO OK and HI The GBK GFK is supplied with a RS 232 bi directional interface and real time clock RTC The GBK GFK has a sealed keypad with colour coded membrane switches and a large easy to read liguid crystal type display LCD supplied with a backlight Includes automatic zero tracking semi automatic tare and accumulation facility that allows the weight to be stored and recalled as an accumulated total OIML Approved models GBK GFK M do not allow pounds units have calibration controlled by jumpers or passcodes and other limitations as noted in the manual 3 page Adam Equipment Company 2011 2 SPECIFICATIONS GBK Models Model GBK8 GBK 16 GBK 32 GBK 60 GBK 120 GBK 16a GBK 35a GBK 70a GBK 130a GBK 2
6. During parts counting the display can be changed to show the net weight unit weight and number of parts by each time pressing the Func key 20 JPage Adam Equipment Company 2011 0 Il Et tt tt 1 1100 A o mm H g pos 5 2303 l L mm m L 17 pcs ES l 0 II TT 1 1100 e To count a different sample quantity press the Count key The display will show the last used sample size Either use this sample size with a different part or enter a new sample size as above e To return to weighing press Unit when NK nes is displayed 21 Page Adam Equipment Company 2011 10 5 CHECK WEIGHING Check weighing is a procedure to display an indicator or sound an alarm when the weight on the platform meets or exceeds the values stored in the memory The memory holds values for a high limit and a low limit Either or both the limits can be set by the user NOTE 1 The alarm and the LED bargraph can each be set to OFF See section 13 1 The LCD display will indicate whenever the weight is within or exceeds the limits by showing OK HF or LO fh Mass on the platform is above the high limit OK Mass is between the limits Lo Mass is below the low limit 2 The limits can be locked by the manager A Limit Password must be used to change the limits or recall other limits from memory 3 If Limit Password is enabled then enter the password which will allow you to change th
7. RS 232 interface Default Specifications RS 232 output of weighing data ASCII code 9600 Baud user selectable 8 data bits No Parity Connector 9 pin d sub miniature socket Pin3 Output Pin 2 Input Pin5 Signal Ground The scale can be set to print text in English French German or Spanish See the RS 232 parameters section for details 34 Page Adam Eguipment Company 2011 Data Format Normal Output Only weight value along with the weighing unit is printed If Percent weighing is used then is shown in place of weighing units 12 09 2006 lt cr gt lt lf gt 14 56 27 lt cr gt lt l gt 123456 lt cr gt lt lf gt If ID is zero it is left blank 234567 lt cr gt lt lf gt 1 234 kg lt cr gt lt lf gt Net Wt or Gross Wt Data Format Parts Counting Output Weight Unit weight and number of parts are printed lt cr gt lt l lt cr gt lt l Date 12 09 2006 lt cr gt lt l Time 14 56 27 lt cr gt lt l lt cr gt lt l Scale II 123456 lt cr gt lt l User II 234567 lt cr gt lt l lt cr gt lt l Net Wt 1 234 kg lt cr gt lt l Net Wt or Gross Wt Unit Wt 123 g lt cr gt lt l for metric and Ib for pounds PCS 10 pes lt cr gt lt l lt cr gt lt lf gt lt cr gt lt lf gt 35 Page Adam Equipment Company 2011 Data Format Memory Recall Output 12 09 2006 lt cr gt lt 14 56 27 lt cr gt lt 123456 lt cr gt l
8. allow access to a limited set of parameters as described in section 6 2 NON APPROVED SCALES Non EC Approved scales will allow entry to the parameters if the Tare key is pressed during the power on cycle The passwords work as above 15 1 USING 0000 TO ENTER THE CALIBRATION PARAMETER Pn When Pn is displayed Enter 0000 and press Tare UnLoAd Empty the platform by removing the load if there is any and press Tare LoAd 6 KiLoS Load the requested calibration weight and press Tare SPAn PASS If Calibration is complete SPAn PASS will be 51 Page Adam Equipment Company 2011 displayed Remove the calibration weight Or SPAn FAiLEd This means calibration has failed Remove the calibration weight and repeat the process JP On Remove the jumper or shorting of the pins whichever is used The scale will return to normal weighing 15 2 USING 1000 TO ENTER THE SERVICE PARAMETERS Non Approved indicators For the non approved indicator press the Tare key during the display counting when turned on Approved Indicators For the Approved version a jumper can be installed to allow access or the Calibration and Parameter Counters must be enabled see 15 2 10 Calibration Access on Approved Scales Pin 1 Pin 2 Jumper JTAG Input for programming 55 ver E DR26 pas DR22 DU3 na L
9. for setting the language baud rate printing mode etc The user can also set a Scale ID number and a User ID number Parameter Description Options Default Values or setting C1 on Enable or disable the RS Prt on Prton 232 interface Prt OFF C2 bd Baud Rate 600 9600 1200 2400 4800 9600 19200 44 Page Adam Equipment Company 2011 C3 PrM Printing Mode Manual MAN mAn Continuous or Automatic Cont Goron tCspproved scales AUto C4 Aon Enable or disable the ACON AC on Accumulation AC OFF C5 Ln Select Language EnGli English EnGLi FrEnGH French GErmAn German SPAN Spanish C6 Uld Set User ID To be entered manually 000000 C7 Sid Set Scale ID To be entered manually 000000 Scale will perform the following depending on the Accumulation and Print Settings ACCUMULATION AC on AC Off SETTINGS PRINT SETTINGS AUto Accumulate and print Print automatically automatically Do not accumulate man Accumulate and Print only Print when Print key is pressed when Print key pressed Do not accumulate Cont Print continuously Print continuously Not E Ge Accumulate when Do not accumulate approved scales Print key is pressed 45 Page Adam Eguipment Company 2011 13 3 Scale Parameters e Shortcut to enter this group is to press and hold the Count Key for 4 seconds The display will go directly to S1 Un e P
10. per uso 2006 95 EC Instrumentos electricos entro certi limiti di para uso dentro cierti voltaggio Directivo di limites del voltaje voltaggio basso Diretivo di voltaje bajo 2004 108 EC EMC richtlijn 2004 108 EC Compatibilita 2004 108 EC Compatibilidad electromagnetico electromagnetico Deze verklaring is alleen geldig samen met Questa dichiarazione e valida solamente se Esta declaracion es valida solamente si een certificaat van overeenstemming accompagniato da un certificato di conformita accompagniato a un certificado da afgegeven door een bevoegde instantie relaciato da un ente riconosciuto conformidad emitida par un organismo notificado Signature Date Unterschrift Datum Signature Date 22 July 2011 Handtekening Datum Firma Date Firma S Cu m ba C h Fache 63 Page Adam Eguipment Company 2011 64 Page Adam Eguipment Company 2011 CE Manufacturer s Declaration of Conformity This product has been manufactured in accordance with the harmonised European standards following the provisions of the below stated directives Electro Magnetic Compatibility Directive 2004 108 EC Low Voltage Directive 2006 95 EC Adam Equipment Co Ltd Bond Avenue Denbigh East Milton Keynes MK1 1SW United Kingdom FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable prote
11. the current values will be displayed These values should match the values marked on the scale at the time of verification if it has been verified 10 Page Adam Eguipment Company 2011 KEYPAD PRIMARY FUNCTION Sets the zero point for all subseguent weighing The display shows zero It tares the scale and stores the current weight in memory as a tare value subtracts the tare value from the weight and shows the results This is the net weight This is used to select the weighing units from a preset list of available units 11 Page SECONDARY FUNCTION Escape from any setting menus Accept the set values Allows the weight unit weight and count to be seen when parts counting or to change from weight to in percent weighing Adam Eguipment Company 2011 Count Print 1 to 0 and CE It sets the limits for check weighing and allows setting of either the low limit or the high limit or both It stores and recalls any of 10 preset limits This is used to select percent weighing RS 232 parameters Operation of the bar graph RTC settings User ID and Scale ID Enter Parts Counting It is used to print the results to a PC or printer using the RS 232 interface It also adds the value to the accumulation memory if the accumulation function is not automatic Allow entering numerical values where reguired setting of limits tare value time and date for example 12 Page Adam Egui
12. tique This declaration is only valid when Diese Erkl rung gilt nur in Verbindung mit einer Cette d claration est seulement valide quand accompanied by a Certificate of Conformity issued by a Notified Body Konformit tsbescheinigung einer benannten Stelle elle est accompagn e par une Attestation de Conformit d livr e par un Organisme Notifi Fabrikant Adam Equipment Co Produttore Adam Equipment Co Fabricante Adam Equipment Co Ltd Ltd Ltd Type GK M Modello GK M Tipo GK M spe GBK M GFK M GBK M GFK M GBK M GFK M Nummer van de N di certificato di Numaro del Verklarling van UK 2860 POYADIONG di tipo UK2860 certificado de UK2860 EG GB1320 GE P GB1320 aprobacion de GB1320 typegoedkeuring tipo CE Conform met het model beschreven in de verklaring van EG typegoedkeuring en met de voorschriften van EG richtlijn 2009 23 EC zoals gewijzigd en met de Conforme al modello di produzione descritto nel certificato di approvazione de tipo CE e secondo le richieste CE direttivo 2009 23 EC come modificato e secondo le rechieste della seguente directive CE volgende EG richtlijnen Conforme al modello di producion descrito nel certificado di aprobacion del tipo CE e segun los requisitos del CE diretiva 2009 23 EC como modificato e segun los requisitos della siguiente diretive CE 2006 95 EC Laagspanning richtlijn 2006 95 EC Strumenti elettrici
13. 11 Press Tare again to enter percent weighing The scale will set the sample mass on the platform as 100 reference weight NOTE If there is no reference weight on the platform and percent weighing function is entered pressing Tare again will return the indicator to normal weighing 000 d 0 IA Ett ttt l l 1100 Remove the sample weight Then any other weight placed on the scale will be displaved as a percentage of the original sample For example if 3500g is placed on the scale and percent weighing is selected the display will show 100 00 Remove the 3500g weight and place a 3000g weight The display will show 85 7 as 3000g is 85 7 of 3500g 085 1 0 IA IIId l 1100 gt The number of decimal points will depend on the weight used A smaller weight will show only 100 while a larger weight might show 100 00 If the scale was showing zero weight before entering this function then the user must manually enter the weight to be set as 100 When F4 PCT is displayed enter the weight to be used for the 100 reference then press Tare to accept the reference weight The display will show 0 00 27 Page Adam Equipment Company 2011 e If the scale shows XX XX which is the last weight used as a reference press CE to clear and use the numeric keypad to enter a new value Press Tare to accept the new reference weight e The weight entered must be greater than 50 sca
14. 300kg 660lb 600kg 1320lb 75kg 165lb 150kg 330lb Readability 5g 0 01lb 10g 0 02Ib 20g 0 05lb 50g 0 1lb 1g 0 0021b 2g 0 005lb Repeatability Std Dev 5g 0 01lb 10g 0 02Ib 20g 0 05Ib 50g 0 1lb 2g 0 004lb 4g 0 01lb Linearity 10g 0 021b 20g 0 04lb 40g O 11b 100g 0 21b 3g 0 006lb 6g 0 015lb Units of Measure Grams amp Kilograms XXXa also to have Pounds Ounces amp Pound Ounces Stabilization Time 2 3 Secs Operating Temperature 10 C to 40 C 14 F to 104 F Power Supply 230VAC 50 60Hz in Europe Asia and South Africa 12vDC 800mA UL CSA adapter for USA Calibration External Calibration Mass User Selectable Display Backlit Green display 25mm with capacity tracker Balance Housing Cast aluminum base Pantone cool grey painted base stainless steel grade 304 Top pan ABS Cool grey indicator housing Pan Size 400mm x 500mm 400mm x 500mm 400mm x 500mm 600mm x 800mm 400mm x 500mm 400mm x 500mm 15 7 x 19 7 15 7 x 19 7 15 7 x 19 7 23 6 x 31 5 15 7 x 19 7 15 7 x 19 7 Overal Dimensions 400 mm x 620 mm x 400 mm x 620 mm x 400 mm x 620 mm x 600 mm x 940 mm x 400 mm x 620 mm x 400 mm x 620 mm x w xd xh 860 mm 860 mm 860 mm 900 mm 860 mm 860 mm 15 7 x 24 4 x 33 8 15 7 x 24 4 x 33 8 15 7 x 24 4 x 33 8 23 6 x 37 x 35 4 15 7 x 24 4 x 33 8 15 7 x 24 4
15. 60a Maximum Capacity 8kg 16lb 16kg 35lb 32kg 70lb 60kg 130lb 120kg 260lb Readability 0 1g 0 00021b 0 5g 0 0011b 1g 0 0021b 2g 0 0051b 5g 0 011b Repeatability Std Dev 0 2g 0 00041b 1g 0 0021b 2g 0 0041b 4g 0 01lb 10g 0 021b Linearity 0 3g 0 00061b 1g 0 0021b 2g 0 0041b 4g 0 011b 10g 0 021b Units of Measure Grams amp Kilograms XXXa also to have Pounds Ounces amp Pound Ounces Stabilization Time 2 3 Secs Operating Temperature 10 C to 40 C 14 F to 104 F Power Supply 230VAC 50 60Hz in Europe Asia and South Africa 12vDC 800mA UL CSA adapter for USA Calibration External Calibration Mass User Selectable Display Backlit Green display 25mm with capacity tracker Balance Housing Cast aluminum base Pantone cool grey painted base stainless steel grade 304 Top pan ABS Cool grey indicator housing Pan Size 300mm x 400mm 11 8 x 15 5 Overal Dimensions 300mm x 620mm x 860mm 11 8 x 24 4 x 33 8 wxdxh Net Weight 7 6kg 16 8 Lb 7 6kg 16 8 Lb 7 6kg 16 8 Lb 7 6kg 16 8 Lb 7 6kg 16 8 Lb Features Weighing Counting Checkweighing with LED lights Percentage Hold function RS232 4 Page Adam Eguipment Company 2011 GFK Models Model GFK 75 GFK 150 GFK 300 GFK 600 GFK 75H GFK 150H GFK 165a GFK 330a GFK 660a GFK 1320a GFK165aH GFK330aH Maximum Capacity 75kg 165lb 150kg 330lb
16. ANANA GAGA 19 10 4 PARTS COUNTING mam anamangsakanagnaadung nana a 19 10 5 CHECK WEIGHING naaa o a a Rama u a AA 22 10 5 1 SETTING UP WHILE WEIGHING mpa mia ob Ada aakkoaska kia raka A 23 10 5 2 SETTING UP WHILE PARTS COUNTING OR WEIGHING 24 10 6 LIMITS STORING AND RECALLING nn eee nenene 24 10 7 PERCENT WEIGHING si e z daze u ins k vak ci b voknn d raka anse k vada a n n mi kk mne 26 10 8 ANIMAL DYNAMIC WEIGHING nen 29 10 8 1 ANIMAL WEIGHING PROCEDURE sn a 30 10 9 ACCUMULATED POTA EN 31 10 9 1 MANUAL ACCUMULATION otnnnnnnn nn nn nn nn nn 31 10 9 2 AUTOMATIC ACCUMULATION ooonnnnnnnnnnnnn nn eee nen 33 11 RS 232SPEGIFIGATION aaa NANANA AG 34 11 1 INPUT COMMANDS FORMAT 1 nnaman 39 12 CALIBRATION an ku ka T ak vrana k 40 13 PARAMETER SETTINGS un m m nn ee nn nn 41 13 1 CHECK WEIGHING PARAMETERS nn eee eee nenene nn 41 13 2 RS 232 PARAMETERS s z a vo b k k n s kk 44 13 3 SCALE PARAMETE RS iii v na i sud sedkv zuau a vv ho a NA KANA S UT aku DN se 46 13 4 PERCENT WEIGHING AND ANIMAL WEIGHING ooonnnnnnnnn non 48 14 ERROR MESSAGES ia kva l n nal lo 49 15 SERVICE PARAMETERS 11111111110000aananananasanasasasasasasasasasasasasasasasasana 51 15 1 ACCESS TO PARAMETERS o ooon nnnnnnnn nn s non nenes 51 15 2 USING 1000 TO ENTER THE SERVICE PARAMETERS 52
17. Damaged load cell Damaged Electronics Err 6 A D count is not correct Load cell is damaged when turning the scale on a Electronics is damaged Err7 Percent input error Percent function is entered with no reference mass on the platform Err 8 High limit input error Low limit is set first then the high limit is set lower than the low limit and high limit not equal to zero 49 Page Adam Equipment Company 2011 Err 9 Low limit input error High limit is set first then the low limit is set higher than the high limit and low limit not egual to zero FAILH or Calibration error Improper calibration should be Within 11046 of the factor FAILL calibration The old calibration data will be retained until the calibration process is complete 50 Page Adam Equipment Company 2011 15 SERVICE PARAMETERS 15 1 ACCESS TO PARAMETERS APPROVED SCALES Access to the scale parameters and calibration is controlled in all approved scales either by limiting access to be after the Calibration Jumper is put on the PCB location J1 pins 1 amp 2 In this case the display will show the passcode request screen P To continue enter a passcode as described below Or if the Calibration and Parameters have been enabled the user must enter the correct password to have access See Section 6 0 Entering passcode 0000 will allow calibration as shown in 15 1 entering 1000 will
18. E LI L meee nu 4217 1 ns k mm es m reg Ee DR PR21 j pad PUS PES RE U1 DR PET 3 I 83 2400 OS puz an is er je mm Ba e m m ame 5 a m m m cz ame sm S A Pos FM 2 a EE ARA m nl 22 22 E SYET Lil E a EUR 52 Page Adam Equipment Company 2011 Apply power to the indicator If the jumper has been used the display will ask for a code number PN on the Weight Display immediately Or press the Tare key during the time the calibration counters are being displayed Enter the number 1000 when Pn is displayed and then press Tare The displays will show the first parameters called KA Int To select another parameter press the Func key to advance through the parameters Press the Tare key to enter a parameter To exit a parameter press the Zero key The display will show the parameter number and a name When a parameter is entered by pressing the Tare key the displays will guide you through the parameter selected and the options available The parameters available are FA int Initial Zero Range Fo FEZ Re Zero range F6 SCS Successive Tare Enable H Cnt Display the A D counts F6 Zem Zero Mode F9 Lud Low voltage detection F10 Cn GK M only Calibration and Parameter counters or M0 Az Auto Zero Range 53 Page Adam Eguipment Company 2011 F4 INITIAL ZERO RANGE To enter thi
19. Eguipment Company 2011 added to the first one Again only the weight that is added after taring will be displayed 0 IA tt dd 11 1100 NOTE When the container is removed a negative value will be shown If the scale was tared just before removing the container this value is the gross weight of the container plus all products which were removed The zero indicator will also be on as the platform is back to the same condition it was when Zero was pressed last Press Tare or Zero to remove the tare value and display zero The Net indicator will disappear 10 2 2 PRESET TARE NOT AVAILABLE ON APPROVED SCALES When the scale is at zero with no weight on the platform it is possible to enter a preset tare e Zerothe scale by pressing Zero The zero indicator will be on e Enter a value using the numeric keys e Press Tare to tare the scale The value that was entered is stored as the tare value and it is subtracted from the display leaving a negative number on the display 18 Page Adam Eguipment Company 2011 10 3 WEIGHING To determine the weight of a sample first tare an empty container if used then place the sample in the container The display will show the weight and the unit of weight currently in use 0 IA 1 1 tt tt l Il 1100 To change the weighing unit press the Unit key The only alternative weighing unit is pounds This can be enabled by the user in the parameters section See secti
20. This document is hosted by Old Will Knott Scales www oldwillknottscales com EE ADAM Adam Equipment GBK and GFK Series P N 9679 Revision C2 July 2011 Software Rev V1 17 GK H scales for Europe V2 25 EC Approved scale V3 32 GK scale for Europe V4 07 GK H scale for USA V5 32 GK scales for USA Adam Eguipment Company 2011 Easy Reference Model name of the scale Serial number of the unit Software revision number Displayed when power is first turned on Date of Purchase Name of the supplier and place Adam Eguipment Company 2011 CONTENTS 1 INTRODUCTION WE 3 2 SPECIFICATIONS E 4 34 INSTALLATION a O a r o a ar 9 3 1 UNPACKING i ociis s cnie void a vk ANAN n kam 9 3 2 LOCATING da d na ala aa a Kaa al aaa ia sn ne ea a oa a alk ada 9 3 3 SETTING UP THE SCALES Uu ol o r e dE r r ink bere 10 4 KEYPAD nanas R K K RV ac a o a a B o n d 11 Ds DISPLAY E 13 5 1 SYMBOLS AND INDICATORS oosnnnnnnnnnnnnnn nn nn nene a nn 13 6 CALIBRATION COUNTER FOR APPROVED SCALES 14 T BATTERY GE 16 8 BACKLIGNIT E 16 9 AUTO POWER OFF s o n o dan o a hm a k 16 10 OPERATION sn dava msn ana Eeer ger eege aaua saias 17 10 1 ZEROING mamamana 17 10 2 TARING aNG 17 10 2 1 MANUAL TARE siennes tie te nad n Vau A ABAK KU Ks 17 10 2 2 PRESET TARE NOT AVAILABLE ON APPROVED SCALES 18 10 35 WEIGHING N
21. X and the total weight before returning to zero e To print the total press Print to recall and then immediately press Print the second time to print the results e To erase the memory press Print to view the total and then immediately press CE to clear the memory 32 Page Adam Eguipment Company 2011 10 9 2 AUTOMATIC ACCUMULATION When the scale has been set to Automatic Accumulation the value is stored in memory automatically e Place a weight on the platform The beeper will sound when the scale is stable indicating the value is accepted Remove the weight e The display will show ACE 1 and then the total in the memory before it returns to zero Adding a 2nd weight will repeat the process e While the weight is on the platform press the Print key to view the values first the accumulation number ACE X and then the total will be shown NOTE 1 The scale will not show the value when a weight is removed 2 In all cases the display must return to zero or a negative number before another sample can be added to the memory 3 More products can be added and Print be pressed again for up to 99 entries until the capacity of display is exceeded 33 Page Adam Equipment Company 2011 11 RS 232 SPECIFICATION The GBK GFK indicator is supplied with bi directional RS 232 interface as standard The scale when connected to a printer or computer outputs the weight with the selected weighing unit through the
22. ally by pressing Print See Section 13 2 NOTE 1 The accumulation function is available only during weighing It is disabled during parts counting or percent weighing 2 The accumulated weights will be stored in either kg or lb depending upon the weighing unit in use 3 If at any time the weighing units are changed the accumulated data will be lost 10 9 1 MANUAL ACCUMULATION When the scale is set to manual accumulation the weight displayed will be stored in the memory when the Print key is pressed and the weight is stable e Remove the weight and press Print when the scale is at zero The display will show AGE 1 and then the weight in memory for 2 seconds before returning to normal The weight can be output to a printer or PC using the RS 232 interface BEI OI 0 A 1101101010101 1100 0 IA TT 1 1100 31 Page Adam Eguipment Company 2011 e When the scale is at zero place a second weight on the platform When stable press Print to accumulate the weight The display will show ACC 2 for 2 seconds and then show the new total LAT 2 0 Il ITTTTTTI 1100 ne ZE IO 0 l A 10111111 EL 1100 sUoco e Continue until all weights have been added This can continue for up to 99 entries until the capacity of display is exceeded e To view the total in memory press the Print key when the scale is at zero The display will show the total number of accumulation AGG X
23. always off always on or automatic on only when the scale is in use or a key is pressed See setting of the parameter S2 BL in section 13 3 9 AUTO POWER OFF The auto power off can be set by the user to disable the feature or to a pre set time interval See setting of the parameter S3 AOF in section 13 3 16 Page Adam Equipment Company 2011 10 10 1 10 2 10 2 1 OPERATION ZEROING You can press the Zero key at any time to set the zero point from which all other weighing and counting is measured This will usually be necessary when the platform is empty When the zero point is obtained the display will show the zero indicator The scale has an automatic re zeroing function to account for minor drifting or accumulation of material on the platform However you may need to press Zero to re zero the scale if small amount of weight is still shown when the platform is empty TARING MANUAL TARE Zero the scale by pressing Zero The zero indicator will be on Place a container on the platform and its weight will be displaved Press Tare when the reading is stable The weight that was displaved is stored as the tare value and it is subtracted from the display leaving zero on the display The stable and Net indicator will be on 00000 As a product is added only the weight of the product will be shown The scale could be tared a second time if another type of product was to be 17 Page Adam
24. ange the value Press Tare to accept the displayed value Press Zero to return to weighing 56 Page Adam Eguipment Company 2011 16 REPLACEMENT PARTS AND ACCESSORIES If vou need to order any spare parts and accessories contact your supplier or Adam Eguipment A partial list of such items is as follows e Main Power cord or adaptor for e Stainless Steel Pan USA versions e n use cover e Replacement Battery e Printer etc 57 Page Adam Equipment Company 2011 17 SERVICE INFORMATION This manual covers the details of operation If you have a problem with the scale that is not directly addressed by this manual then contact your supplier for assistance In order to provide further assistance the supplier will need the following information which should be kept ready A Details of your company Name of your company Contact person s name Contact telephone e mail fax or any other methods B Details of the unit purchased This part of information should always be available for any future correspondence We suggest vou to fill in this form as soon as the unit is received and keep a print out in your record for ready reference Model name of the scale GFK Serial number of the unit Software revision number Displayed when power is first turned on Date of Purchase Name of the supplier and place C Brief description of the problem Include any recent history of the uni
25. automatico Manufacturer Adam Eguipment Co Hersteller Adam Eguipment Co Fabricant dam Eguipment Co Ltd Ltd Ltd Type GK M Typ GK M Type OK MI GBK M GFK M GBK M GFK M GBK M GFK M No of the EC o type approval UK2860 in BG UK2860 pi du KAP UK2860 certificate GB1320 E GB1320 appro aion GB1320 CE de type Corresponds to the production model described in the EC type approval certificate and to the requirements of the Council Directive 2009 23 EC as amended and to the requirements of the following EC Entspricht dem in der Bescheinigung ber die Bauartzulassung beschriebenen Baumuster sowie den Anforderungen der EG Richtlinie 2009 23 EC in der jeweils geltenden Anforderungen folgender EG Richtlinien Fassung und den Correspond au mod le d crit dans le certificat d approbation CE de type aux exigences de la directive 2009 23 EC modifi e et aux exigences des directives CE suivantes Directives 2006 95 EC Electrical equipment 2006 95 EC Elektrische Betriebsmittel 2006 95 EC Mat riel lectrique pour for use within certain zur Verwendung innerhalb utilisation dans des limites voltage limits Low bestimmter de tension d finies Voltage Directive Spannungsgrenzen Directive Basse Tension Niederspannungsrichtlinie 2004 108 EC Electromagnetic 2004 108 EC Elektromagnetische 2004 108 EC Compatibilit compatibility Vertr glichkeit lectromagn
26. ction against harmful interference when the equipment is operated in a commercial environment The equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device Changes or modifications not expressly approved by Adam Equipment could void the user s authority to operate the equipment WEEE COMPLIANCE Sealed Lead Acid Battery Must be recycled Properly Any Electrical or Electronic Equipment EEE component or assembly of parts intended to be incorporated into EEE devices as defined by European Directive 2002 95 EEC must be recycled or disposed using technigues that do not introduce hazardous substances harmful to our health or the environment as listed in Directive 2002 95 EC or amending legislation Battery disposal in Landfill Sites is more regulated since July 2002 by regulation 9 of the Landfill England and Wales Regulations 2002 and Hazardous Waste Regulations 2005 Battery recycling has become topical and the Waste Electrical and Electronic Eguipment WEEE Regulations are set t
27. dy to weigh 29 Page Adam Equipment Company 2011 10 8 1 ANIMAL WEIGHING PROCEDURE e With the platform empty the display will show zero weight Place containers or blankets onto the platform and press the Tare key to zero the display The scale may go into the animal weighing procedure when the items are placed on the scale but will return to showing zero when the Tare key is pressed e Place the animal to be weighed on the platform The display will show Ani until a stable weight is determined The time it takes for the stable value will depend upon the setting of the filter parameter in the first step e When a stable reading is found the display will show this value and the display will be locked until the Unit key is pressed The display will show the Hold symbol while the display is locked Remove the animal the display will hold the weight value e To weigh a second animal press the Tare key if necessary to zero the display and place the next animal on the scale It is also possible to simply place the next animal on the scale without clearing the last value first The scale will detect the new weight and hold it as before e The scale will remain in the animal weighing mode until the Zero key is pressed Then it will return to normal weighing 30 Page Adam Eguipment Company 2011 10 9 ACCUMULATED TOTAL The scale can be set to accumulate when a weight is added to the scale automatically or manu
28. e it will display done 8 CAL Calibration Calibrate the scale See Section 10 0 47 Page Adam Equipment Company 2011 13 4 PERCENT WEIGHING AND ANIMAL WEIGHING See section 10 7 and 10 8 for details of these special weighing modes Parameter Description Options Default setting F4 PCI This parameter allows the None Enabled user to enter the Percent always weighing Function See Section 10 7 F4 AnL Enter the Animal Weighing Set the filter value Enabled mode of operation See Always section 10 8 48 Page Adam Eguipment Company 2011 14 ERROR MESSAGES During the initial power on testing or during operation the scale may show an error message The meaning of the error messages is described below If an error message is shown repeat the step that caused the message If the error message is still shown then contact your dealer for support ERROR DESCRIPTION POSSIBLE CAUSES CODE Err 1 Time input Error Invalid time entry such as 268910 for the time format H m Err 2 Date input Error 34th day of a month is an invalid entry Err 4 Initial Zero is greater than Weight on the platform when turning allowed 4 of maximum the scale on capacity when power is Excessive weight on the platform turned on or when the when zeroing the scale Zero Enter key is pressed Platform is not installed Improper calibration of the scale
29. e limits or the operation of the beeper or bargraph 22 Page Adam Equipment Company 2011 10 5 1 SETTING UP WHILE WEIGHING Press the Low Limit key It will show the current low limit The LO symbol will appear on the display Press the CE key to clear the old value and then enter the new low limit using the numeric keys The decimal point is fixed at the position that is used for the current weighing unit When the desired value is shown press Tare to accept the value If you want to reset the value to zero press CE to clear the value The limits are displayed in the weighing unit in use To set the high limit press High Limit the display will show the high limit the HI symbol will be on to the left side of the display Set the high limit in the same way the low limit was set Pressing the Tare key to enter the value will return the scale to weighing with the Check weighing function enabled 23 Page Adam Eguipment Company 2011 10 5 2 SETTING UP WHILE PARTS COUNTING OR WEIGHING During parts counting and percent weighing the limits are set in the same way as above The limits are displayed in pcs or See Section 10 4 for the description of parts counting and Section 10 7 for percent weighing NOTE 1 The weight must be greater than 20 scale divisions for the check weighing to operate 2 Todisable the check weighing function enter zero into both the limits as described above When
30. eighing CHECK WEIGHING PARAMETERS Shortcut to enter this group is to press and hold the Unit key for 4 seconds The display will go directly to FUNE 1 Press Tare to enter the group Press Func to scroll through the parameters and press Tare to enter a parameter setting 41 Page Adam Equipment Company 2011 e Press Func to view the options for setting e Press Tare to confirm the change and then advance to the next parameter by pressing the Func key This group of parameters enables or disables the percent weighing sets the lock for re setting the check weighing limits enables or disables the check weighing LED indicator enables or disables the check weighing alarm sets the User Password for check weighing enables or disables the negative check weighing Parameter Description Options Default setting H LLK This parameter prevents the With LLK set to Off oFF OFF normal user from changing the user is allowed to the limits with the help of a change limits at any Limit Lock time With LLK set to Preset PSt the user is allowed to use one of the preset limits only 42 Page Adam Eguipment Company 2011 F2 LEd This parameter sets the LED indicator to off or on and the LED type whether LED s are on in the form of a continuous bar or a spot LED or a segment of colour bAr Bar type Spot Spot type Seg Segment OFF Off This Beep
31. er to off or on If set to parameter sets the on the beeper can further be set to sound when the weighing result is within or outside the check weighing limits bP oFF Off WP inL Within limits hP otL Outside limits gt 20d bP ink F4 CPS This setting of a new Check parameter allows weighing password must be entered twice when asked When complete it will display done To be entered manually This negative parameter enables check weighing function with ability to do negative tare NOTE 1 The Check weighing password is separate from the scale password see section 13 3 access to F3 LLC FA LEd Fo DEP F6 CPS and F7 nCK 43 Page If the password is other than 0000 user must enter the password to gain Adam Equipment Company 2011 13 2 RS 232 PARAMETERS e Shortcut to enter this group is to press and hold the Print key for 4 seconds The display will go directly to C1 on e Press Func to view the list of parameters e Press Tare to enter a parameter Press Func to view the options for the parameter settings e Press Tare to confirm the change and then advance to the next parameter by pressing the Func key e Press Zero to return to the group FUNC 2 If vou press Zero again the scale will exit the User Parameter section and return to weighing This group of parameters can be set by the user
32. ill allow user calibration See section 15 1 and the parameter code will allow access to the following parameters see section 15 2 F4 int Initial Zero Range Fo rEZ Re Zero range F6 SCS Successive Tare Enable H Cnt Display ADC counts F6 Zem Zero Mode F9 Lud Low voltage detection 15 Page Adam Eguipment Company 2011 7 BATTERY e The scales can be operated from the rechargeable battery if desired The GBK GFK scales have up to 70 hours battery life before needing to be recharged if the backlight is disabled and the battery is fully charged e When the battery needs charging a symbol on the display will turn on The battery should be charged when the symbol is on The scale will still operate for a period of time after which it will automatically switch off to protect the battery e To charge the battery simply plug into the mains power supply The scale does not need to be turned on e The battery should be charged for 12 hours for full capacity e To the right of the display is a LED to indicate the status of battery charging When the scale is plugged into the mains power the internal battery will be charged If the LED is green the battery is being charged If it is red it is nearly discharged and yellow indicates the battery is increasing the charge level Continue to charge overnight for a complete re charge 8 BACKLIGHT The backlight for the LCD can be set by the user to
33. le divisions e Press Unit to return to normal weighing NOTE The display may jump by large numbers unexpectedly if small weights are used to set as 100 reference The scale checks if the weight is too small and will show Error 7 28 Page Adam Eguipment Company 2011 10 8 ANIMAL DYNAMIC WEIGHING The scale can be set to animal dynamic weighing for weighing any items that are unstable or may move See Section 13 4 The scale will use a special filter to minimise the effects of any movement on the platform e Press Func The first option is FUnG 1 press the Func key 3 more times to display Func 4 FUnCY 0 Il Tt OU OU l i l 1100 e Press the Tare key F4 PCT will be displayed Press the Func key to advance to the second function FA Anl Animal weighing FY Anl 0 Il Prot tt tot L 1100 e Press Tare to enter the animal weighing function e To use the Animal Weighing function it is necessary to set the amount of filtering required for the animals to be weighed More active animals will require a higher level of filtering to give a stable result The display will show Filt x where x is a value from 1 to 5 The higher the value the greater the amount of filter will be To increment the value shown press the Func key then press the Tare key to accept it e The display will flash Ani 2 times then show the current weight 0 00 The scale is now rea
34. limits press Tare when FECALL is displayed The display shows TEG Enter the number corresponding to the desired memory location 0 to 9 to be recalled TEG K will be displayed for 2 seconds indicating the values stored in the location X is being recalled The scale will change to the recalled limits weighing units and settings for the beeper and bar graph 25 Page Adam Eguipment Company 2011 NOTE 1 If the recalled limit is for parts counting the display will show the last sample value used ready for a new sample to be counted 2 If the recalled unit is a percent weighing limit the display will show the last sample value used ready for a new sample to be weighed 3 If the memory location was empty the scale will return to weighing 10 7 PERCENT WEIGHING The scale can be set to perform percent weighing See Section 13 1 The scale will use a mass on the platform as the 100 reference weight If the platform is empty or the scale is tared then the user can input a reference weight using the keypad e f using a reference weight or object as your 100 reference add the weight to the to the platform e Press Func The first option is FUNG T press the Func key 3 more times to display FUnc 4 l Li IL U 0 II TT ttt 1100 e Press the Tare key PE will be displayed FY PCE 0 Il 1 ttt tt ET E 1100 26 Page Adam Eguipment Company 20
35. o impose targets for recycling Adam Eguipment Company 2010 ADAM EGUIPMENT is an ISO 9001 2008 certified global company with more than 35 years experience in the production and sale of electronic weighing eguipment Adam products are predominantly designed for the Laboratory Educational Medical retail and Industrial Segments The product range can be described as follows Analytical and Precision Balances Compact and Portable Balances High Capacity Balances Moisture analysers balances Mechanical Scales Counting Scales Digital Weighing Check weighing Scales High performance Platform Scales Crane scales Medical Scales Retail Scales for Price computing For a complete listing of all Adam products visit our website at www adameguipment com Copyright by Adam Eguipment Co Ltd All rights reserved No part of this publication may be reprinted or translated in any form or by any means without the prior permission of Adam Eguipment Adam Eguipment reserves the right to make changes to the technology features specifications and design of tne eguipment without notice All information contained within this publication is to the best of our knowledge timely complete and accurate when issued However we are not responsible for misinterpretations which may result from the reading of this material The latest version of this publication can be found on our Website www adamegui
36. on 13 3 10 4 PARTS COUNTING The scale can be used to count parts based on the average weight of a sample weighed When more parts are added the total number of parts are displayed e If a container is to be used place this container on the platform before entering parts counting and press Tare e Press Cnt to enter the Parts Counting mode The display will show the last sample size used For example 10 Pes 0 IL Tt D UE 1 1100 19 Page Adam Eguipment Company 2011 Either place 10 parts on the platform for determining the average piece weight or use a different number of parts For example place 20 parts on the platform press IGE to clear the last values and then enter the value 20 using the numeric keypad Gm pcs NET i a 0 l A PEt tt 1 1100 Press Cnt to weigh the samples and determine an average piece weight If the parts are too light to measure accurately the count may become faulty It is suggested that the samples to be weighed should each weigh more than the resolution of the scale After the sample has been weighed the scale will count any other parts added by applying the average piece weight to the weight of the parts to be counted NA ua ok I 0 Il Tt rd UE 1100 The Tare key works normally during this time so it is possible to tare the display with a container on the platform or to enter a preset tare value as described in section 10 2 2
37. parameters using a passcode to limit access The reguirements for doing this stipulate the code should be apparent and recorded in a suitable location on the scale In this way if the record of the Calibration or Parameter counters do not agree with recorded settings the responsible person inspecting the scale can take appropriate action 14 Page Adam Eguipment Company 2011 The Counters are incremented any time the calibration section or the Factory parameters section have been modified At power on the display will show the current software revision number followed by the message of the Calibration Count IALint then a number i e 123 The number from the counter memory Then the Parameter Counter message of PArint and probably a different number i e 234 The counters cannot be reset to 0 they will increment until the display can no longer hold the values 1 to 999999 It is expected we will never have more than 1 million calibrations in the life of the machine Each display is held for 1 2 seconds The scale will then continue to do the display test and go to normal weighing If during the time the counting displays are shown the user presses the Tare key the user will be given a message to enter the passcode necessary to calibrate the scale P Enter the code P0000 to Enter calibration or P1000 to enter the parameters followed by pressing the Tare key The Calibration access w
38. pment Company 2011 5 DISPLAY 5 1 SYMBOLS AND INDICATORS The LCD has unigue symbols to indicate the following 20 The display is at Zero v The scale is Stable Net Net weight The scale has been tared kg Ib Symbols shown for the units Capacity Tracker A bar graph indicating the proportion of the scale capacity being used by the weight on the platform ii yana paaa hamon bana maa ama Low battery bAt LO or 8 The scale is in Percent weighing mode DCS The scale is in Parts counting mode HI OK LO The scale is in Check weighing mode an The colons are used to separate pounds from ounces and for the real time clock 13 Page Adam Equipment Company 2011 Next to the LCD are a number of LED s that show when the weight is below within or over the limits during check weighing Weight LED LCD below the low limit Amber LO Within the limits Green OK Above the high limit Red HI NOTE The LED s can be set by the user to off bar spot or segment mode See F3 LED in section 13 1 The LED can be set to display as a bar increasing from Low to OK to High a single spot increasing from Low OK to High or as a single bar that changes colour as the weight progresses from Low to OK to High 6 CALIBRATION COUNTER FOR APPROVED SCALES The approved GBK GFK M Model scales have the ability to control access to the calibration or metrology
39. pment com Adam Eguipment Company 2010
40. rent from the displayed value enter the value of the mass in whole numbers The kg or the Ib symbol will be on to show the active unit Press the Tare key when the stable indicator is on The scale will calibrate to the mass When complete it will display PASS and then either display S8 GAL if entered the calibration section through the Scale Settings as per section 13 3 or return to normal weighing if entered directly Remove the calibration mass If an error message FAIL H or FAILL is shown re check the calibration and repeat If the error cannot be corrected contact your supplier 40 Page Adam Eguipment Company 2011 13 PARAMETER SETTINGS Pressing the Func key allows the user to access the parameters for customising the scale The parameters are split into 3 groups 1 Check weighing parameters 2 RS 232 parameters and 3 Scale parameters 4 Percent and Animal Weighing Functions 13 1 When Func is pressed display will first show FUME 1 for Check weighing parameters Enter 2 for RS 232 parameters or 3 for Scale parameters or 4 for percent weighing and animal weighing or press the Func key to advance through the groups FUNG 1 FUnG 2 FURC 3 and FUNC 4 Press Tare to enter the desired group of parameters Press Zero to return to the group FUME 1 If vou press Zero again the scale will exit the User Parameter section and return to normal w
41. ress Func to view the list of parameters e Press Tare to enter a parameter Press Func to view the options for the parameter settings e Press Tare to confirm the change and then advance to the next parameter by pressing the Func key e Press Zero to return to the group FUNG 3 If vou press Zero again the scale will exit the User Parameter section and return to normal weighing This group of parameters are used to control the operation of the scale Parameter Description Options Default setting 1 Un Enable or disable weighing Kg kg units Not all units are g available for all scales Ib settings o 02 Only USA scales have 1 02 imperial unit 2 hl Backlight set to always on EL OFF EL AU always off or automatic on FL on whenever a weight is EL AU placed or a key is pressed 46 Page Adam Equipment Company 2011 S3 AoF Auto Off Disable or set SLP 0 SLP 0 time increment to turn off SIP 1 scale SIP 5 SLP 10 4 dt Set Time and Date format Enter the time 00 00 00 and settings manually Na Enter the date EN manually S5 dis Display all weights or only ALL ALL when stable StAb 6 Fi Filter setting to slow SLOW nor normal or fast nor FASt S7 SPS Scale Password If it is PI lt 0000 anything other than 0000 then the user must enter the password to gain access to any of the scale parameter settings Must be entered twice when asked When complet
42. ried out under the warranty does not extend the warranty period Components removed during the warranty repairs become the company property The statutory right of the purchaser is not affected by this warranty The terms of this warranty is governed by the UK law For complete details on Warranty Information see the terms and conditions of sale available on our web site 59 Page Adam Equipment Company 2011 19 APPENDIX PARAMETER LAYOUT for GK GBK GFK SCALES Press the Func key to enter Functions mode Key functions while in this section Tare enter a parameter or accept the changes Func move to next parameter or option Zero return to previous parameter or return to weighing FUNC1 Check weighing parameters FUNC 2 RS 232 Parameters FUNC 3 Scale Parameters FUNC 4 Scale Parameters F1 LLk Limit Lock F2 Led LED display F3 bEP Beeper Control F4 CPS Check weighing password F5 NCk Negative Check weighing oFF PSt pre set bAr Bar type Spot spot type SPEA whole segment bP oFF bP Int Inside Limits bp ott Outside Limits Enter using numeric method off C1 on Enable RS 232 C2 bd Baud Rate C3 Prm Printing Mode C4 Aon Enable Accumulation C5 Ln Language for printing C6 Uid User ID C7 Sid Scale ID Prton Prt oFF 600 To 19200 mAn Manual Cont continuous AUto Automatic on oFF
43. s parameter press the Tare key when F4 Int is shown The display will show the current initial zero range Press the Fume key to change the value and press Tare to accept the value Press Zero to return to weighing F5 RE ZERO RANGE To enter this parameter press the Tare key when F9 FEZ is shown The display will show the current re zero range Press the Func key to change the value Press Tare to accept the value Press Zero to return to weighing F6 SUCCESSIVE TARE To enter this parameter press the Tare key when F6 SCS is shown The display will show if the successive tare is on or off Press the Func key to change the value Press Tare to accept the displayed value Press Zero to return to weighing F7 ADC COUNTS To enter this parameter press the Tare key when FI Cnt is shown This parameter allows you to view the A D counts from the internal A D converter This can be an aid to service Press the Tare key to return to the PARAMETER menu Press the Zero key to return to weighing Typical value at zero is 30 000 90 000 approx Typical value at full capacity is 500 000 approx 54 Page Adam Equipment Company 2011 F8 ZERO MODE To enter this parameter press the Tare key when F8 ZEM is shown Select the Zero mode desired In all but special cases Zero Mode 1 is used The other 2 zero modes are for unigue locations in the world and effect the
44. t For example Has it been working since it s delivered Has it been in contact with water Damaged from a fire Electrical Storms in the area Dropped on the floor etc 58 Page Adam Equipment Company 2011 18 WARRANTY INFORMATION Adam Eguipment offers Limited Warranty Parts and Labour for the components failed due to defects in materials or workmanship Warranty starts from the date of delivery During the warranty period should any repairs be necessary the purchaser must inform its supplier or Adam Eguipment Company The company or its authorised Technician reserves the right to repair or replace the components at any of its workshops depending on the severity of the problems However any freight involved in sending the faulty units or parts to the service centre should be borne by the purchaser The warranty will cease to operate if the eguipment is not returned in the original packaging and with correct documentation for a claim to be processed All claims are at the sole discretion of Adam Eguipment This warranty does not cover eguipment where defects or poor performance is due to misuse accidental damage exposure to radioactive or corrosive materials negligence faulty installation unauthorised modifications or attempted repair or failure to observe the reguirements and recommendations as given in this User Manual Additionally rechargeable batteries where supplied are not covered under warranty Repairs car
45. t l gt 234567 lt cr gt lt l lt cr gt lt l gt 5 lt cr gt lt lf gt 1 234 kg lt cr gt lt lf gt 10 pcs lt cr gt lt lf gt lt cr gt lt l gt 86 Page Adam Equipment Company 2011 Data Format Continuous Output Normal weighing 1 234 kg lt cr gt lt lf gt Net Weight or Gross wt Data Format Continuous Output Parts Counting Net 1 234 kg lt cr gt lt l U W 123 g lt cr gt lt l PCS lt cr gt lt lf gt lt cr gt lt lf gt Net Weight or Gross wt Kg and g for metric and Lb for pounds 10 pes lt cr gt lt l NOTE The accumulated total will not be sent to the RS 232 when the continuous print is turned on The continuous print will only be for the current weight and the display data In other languages the format is the same but the text will be in the language selected 3 7 Page Adam Equipment Company 2011 Description ENGLISH FRENCH GERMAN SPANISH Net weight Net WL Pds Net Net Gew Pso Net Weight per unit Unit Wt Pds unit Gew Einh Pso Unid counted Number of items Pes Pcs Stck Piezas counted Number of NO Nb Anzhi Num weighing added to subtotals Total weight and Total Total Gesamt Total count printed Print date Date Date Datum Fecha Print time Time Heure Zeit Hora Scale ID number Scale ID Bal ID Waagen ID Bal ID User ID Number UserID Util ID Nutzer ID Usuario ID
46. tact with water Do not spray or immerse the scales in water e Avoid air movement such as from fans or opening doors Do not place near open windows or air conditioning vents E e e Keep the scales clean Do not stack material on the scales when they are not in use 9 Page Adam Eguipment Company 2011 3 3 SETTING UP THE SCALES The pillar is attached to the base using a bracket that must be attached to the base frame first using the 4 bolts supplied The pillar is secured to the bracket using 2 sets of screws The cable from the base to the indicator module is run through the tube and taken out through the plastic support at the top Excess cable can be stored within the tube The GBK GFK Series comes with a stainless steel platform packed separately Place the platform in the base Level the scale by adjusting the four feet If the scale rocks re adjust the feet E Attach the indicator module to the pillar by sliding it over the bracket with the flanges engaged in the groves on the base Attach the cable from the base to the connector on the rear of the indicator Attach the power to the indicator Press the On Off key The software revision number will be displayed followed by a self test showing all digits before the zero is displayed along with the unit of weight that was selected last If the scale is an approved version GBK GFK M and the Calibration Counter has been enabled see section 6
47. the current limits are shown press CE to clear the settings then press Tare to store the zero values 10 6 LIMITS STORING AND RECALLING The scale can store up to 10 sets of high and low limits in memory along with the weighing units in use including pcs for parts counting and 96 for percent weighing as well as settings for the beeper and bar graph During Check weighing the current limits can be stored or previously stored units can be recalled 24 Page Adam Eguipment Company 2011 rECALL 0 1 1 ttt dt 1 1100 CEO Scure S 0 II 1 1 1 1 1100 Press the Lim key If you are already in the check weighing mode the display will ask if you wish to store the current limits by showing SIE or recall another set of limits by showing FECALL The Lim key can be used to toggle between SIOrE and rECALL wg GM IL kg SCE E f ka If you want to store the limits when StOrE is displayed press the Tare key The display shows SE Enter a number corresponding to the desired memory location 0 to 9 t K will be displayed for 2 seconds indicating the location X where the current limits weighing units and settings for the beeper and bar graph are stored The scale will continue to work with the current settings as active 0 l A Pd tt tt bt bt 1100 SEN 0 Il illit tt i 1100 If you wish to recall any of the pre stored
48. to 104 F Power Supply 230VAC 50 60Hz Calibration External Calibration Mass User Selectable Display Backlit Green display 25mm with capacity tracker Balance Housing Cast Aluminum base Pantone cool grey painted base stainless steel grade 304 Top pan ABS Cool grey indicator housing Pan Size 400 mm x 500 mm 15 7 x 19 7 Overal Dimensions 400 mm x 620 mm x 860 mm wxdxh 15 7 x 24 4 x 33 8 Net Weight 13kg 28 Lb Weighing Counting Checkweighing with LED lights Percentage Hold Features function RS232 7 Page Adam Equipment Company 2011 8 Page Adam Eguipment Company 2011 3 INSTALLATION 3 1 UNPACKING The GBK GFK scales have already been adjusted to work with a platform and have been configured for this application The platform and indicator have been calibrated as a pair and must be used together 3 2 LOCATING ZE e The scales should not be placed in a location that will reduce the accuracy e Avoid extremes of temperature Do not place in direct sunlight or near air conditioning vents e Avoid unsuitable tables The table or floor must be rigid and not vibrate BS e Avoid unstable power sources Do not use near large users of electricity such as welding equipment or large motors a e Do not place near vibrating machinery Uu e Avoid high humidity that might cause condensation 4 Avoid direct con
Download Pdf Manuals
Related Search