Ni-MH Electric Bike - AWIN TECHNOLOGY CORPORATION
Contents
1. Use of AWIN s high quality quick charger is required 4 AWN AWIN TECHNOLOGYCORP Parts and Components Bell all z Handle Bar Speed contro throttle Iw Break lever AN REOrDIGKe T adie y Basket Battery Pack C i il Quick lever Front brake Controller Tire RIM Kickstand Specified Battery pack and Charger The battery pack may be broken or not function well if the battery pack and charger do not collaborate with each other Therefore please use the charger exclusively developed by AWIN for the battery of the bike 110V or 220V AC power shall be used for charging and it usually takes 2 3 hours to complete a fully charge 3 5 AWN AW TECHNOLOGY CORP The user shall not modify or dismantle any parts or components of the electric bike including chain cover Usage battery pack motor charger etc to avoid danger Kai Prohibitions EEA E OEE E EE ee oe S 1 Children and youngsters below 14 are not allowed to ride the electric bike for the sake of safety 2 It is not allowed to ride the same electric bike by two riders simultaneously 3 A helmet and other appropriate protection equipment shall be worn when riding the electric bike 4 When any abnormality occurs don t ride the electric bike any more 5 Don t ride the electric bike in darkness or adverse weather conditions i 6 Don t ride the electric bike when the road is wet sliding contaminated with mud or oil2. or in other bad conditions Don t ride the electric bike when you don t feel well or are drunk 8 Don t operate the power switch with hands during the riding to avoid danger l 9 Don t ride the electric bike with only one hand with a hand holding objects or umbrella 10 Don t overload the electric bike max 3 kg for the front basket while 10 kg for the rear carrier 11 Keep the electric bike within the safe distance and speed to avoid danger when riding ona downhill path 12 Use the front and rear brakes simultaneously for power braking 13 Park the electric bike on an even road section Dont park it on the slope SA 7 i C wr tin tin tin tin tir tir tir tir tir tir tir tit tit tir tir tit tir tit tit tit tit tie 3 0 AWN AW TECHNOLOGY CORP Installation 1 Unpack Please check all of the components in carton including a electric bike a battery pack a charger a basket a set of pedals a setofinstallation kits and user manual 2 Assembly Release the folding levers Release the folding lever Iland extend the folded bike then fixing the leverMtightly Lo EA a IN Adjust the seat Release the Quick Lever and adjusttoan appropriate height what you desire and press ittightly Battery Pack Holder Padlock LY Install Battery Pack Take the power socket of controller is plugged inthe connector of battery pa
3. AWN TECHNOLOGYCORP Trouble Shooting Charging Fault Possible Causes Measures Charger and 1 Check all connections Charger indicator 2 If it doesn t work contact with us or doesn tlight battery pack our authorized service centers for repair 1 Stop charging and remove the power Abnormal noise odor Chargercircuitfails cable immediately smoke from charger 2 Contact with us or our authorized service centers for repair __ 1 Stop charging and remove the power Chargertemp toohigh Charger circuit fails cable immediately 2 Contact with us or our authorized service centers for repair 1 1 Stop charging and remove the power Chargetimetooshort Charger circuit fails able immediately j or Battery fails 2 Contact with us or our authorized service centers for repair 1 Stop charging and remove the power Seia BEG TENI Battery fails E E too high 2 Contact with us or our authorized service centers for repair Stop riding the electric bike when any abnormality is found during the riding Contact us 886 3 597 3688 orany one of our authorized service centers Don t dismantle or adjust the electric bike without acquiring the prior consent of us 16 AWN AWN TECHNOLOGYCORP Trouble Shooting During Riding Possible Cause Aa 1 Turn onthe power switch again The power indicator dt ponei switch is 2 Make sure that the charging connection i urneq orn between the battery pack and the bi
4. Ni MH Electric Bike OPERATION MANUAL AW EB930 AWIN TECHNOLOGY CORP Table of Contents I Table Of Contents 1ece cee cer eee cee cence essees ees eee reese ees Il Product Features ee e cec cen eee eee cee eee een seese teette II Specifications ce eee eee reece teen eee teen cence IV Parts and Components ee ee ee ert V Usage eee ee Ce ee eee VI Installation ee e eseese cee tennant eseese essees nen ees Vil Charge Method miemieerrosiiersnsine unire prinennienpais VIII Check before Riding eee eee ser tenet 12 X Maintenance and Repair eee eee eee 15 XI Troubleshooting 6er rete eee tee eens 16 4 AWN AWIN TECHNOLOGY CORP Product Features s Dual System A 100 electrically motor driven system E bike and a power assisted system PEDELEC are interchangeable N ee a Traditional Bike Electrical Bike UPA A High Power Ni MH Battery A high power long life cycle rechargeable Ni MH battery is specially designed to be safe and environmentally friendly by eliminating the use of the toxic materials lead amp cadmium angu 3 npe AWN AW TECHNOLOGYCORP Product Features D D D Environmental Friendly Longer Running Distance 610 0010 KM A high power rechargeable Ni MH battery is used to provide electric bike to be able to run a longer distance and usually the distance range of 30 60 kilo
5. ck And lock the padlock of carrier _7 n a ED REN LS Install portable basket Fix the setscrews at points Aand B Hold the bayonet and put the basket into staddle then release the bayonet to fix the portable basket Extend foldable pedals Hold the bayonet of the foldable pedals then extend the pedals for use AWN AWIN TECHNOLOGYCORP Installation 3 Trial Riding A Power Assisted Mode PEDELEC Turn on the power switch and hold on the lever for more than 6 seconds when the battery power LED lights then Siton the seat and stamp the foot pedals to ride the PNZ electric bike in Power Assisted Mode Turn on the power switch and hold on the lever for more than 6 seconds when the battery power LED lights then siton the seat and turn the speed control throttle to ride the electric bike in 100 Electric Mode Notes ofinstalling the battery pack 1 When you put the battery pack into rear carrier please keep the pack holder upside and make sure the position of battery pack is correct or not 2 However you must plug the battery pack socket into the connector of the controller before turning onthe power switch 3 Please keep the key of padlock carefully for fear of your inconvenient 4 Before you want to take out the battery pack firstly peel off the connection between the battery pack and controller J 8 AWN AWIN TECHNOLOGYCORP Ch arge M
6. ethod 1 Attentions when chargingthe battery pack A m A Only use the qualified charger designed exclusively for the battery pack AKeep pied en y Aina away from A The indicator will turn to green when the 4 Place Where tiring may occur charging is completed including fire source smoking Repeated charging shall be avoided mar high alt seg a an because it may shorten the service life BOVeree VENA NOM ATOA Ay of the battery A Charge the battery ata place with A Always keep the charger at a place 9004 Veniialion ang no airect where children is separated from touching XPosure in the sun Guard against electric shock ADo not charge the battery pack in awet environment especially in a rainy day Two standard battery charging approaches are available A Charge the whole electric bike B Take out the battery pack and charge it Battery pack Battery pack Charger 3 AWN AW TECHNOLOGYCORP Charge Method 2 charging Stees 1 Identify the power source of the charger and make sure that the power supply of the electric bikeis tu rned off before the charging begins iin 2 Connection a A Charge the whole electric bike Charger Indications Connect tightly the charging plug of the En nes ON charger to the charging socket on the bike Yellow lights Charging B Charge the take out battery pack Take out the battery pack and connect Green lights F
7. ic bike when any abnormality is found during the riding Contact us at 886 3 597 3688 or e mail to tsengww ms54 hinet net or any one of our authorized service centers Break lever Make sure that the tension of the break lever is proper Tire Make sure that the tire pressure is appropriate air pressure 3 0 kg cm Chain Make sure thatthe tension of the chain is proper Bell Make sure thatthe bellis installed atthe right position and rings well Reflective strip The reflective strip shall be used when riding in the night for the sake of safety 4 3 AWN AWN TECHNOLOGY CORP Riding Instructions O Power switch To ride the electric bike turn on the switch and hold on the break lever for more than 6 seconds The power will shutoff automatically when the electric bike is not ridden within 3 consecutive minutes 2 Indications Battery Capacity Indicator Twoindicators light 50 30 power OO Oneindicator lights less than 20 power O O One indicator blinks charge immediately 3 Release the foot support and make sure that the road surface is even 4 Make sure that no traffic coming from the left and right sides 5 A Power assisted Mode B 100 Electric Mode Sit on the seat and stamp the foot Sit on the seat and turn the speed pedals to ride the electric bike in control throttle to ride the electric Power Assisted Mode bike in 100 Electric Mode Power out
8. k of the switchbox 2 The charging connection is energized ls does notlight between the battery pack 3 1f the electric bike still doesn t work and the bike is de energized contact us or send the electric bike to our authorized service center for repair 1 Check the power connection and turn 1 Power trip on the power switch again Over stamp 2 Battery power too low 2 Charge immediately Insufficient Power 3 Tire pressure too low 3 Pump the tire to provide sufficient pressure 4 1f the electric bike still doesn t work contact us or send the electric bike to our authorized service center for repair Motor Malfunction l Contact us or any one of our Suddentrip Motor Failure authorized service centers abnormal noise odor smoke Ay sc Stop riding the electric bike when any abnormality is found during the riding Contact us 886 3 597 3688 orany one of our authorized service centers Don t dismantle or adjust the electric bike without acquiring the prior consent of us 3 4 AWN AWIN TECHNOLOGY CORP
9. meters would be expected depending on road condition weight load electrical system chosen and battery capacity used More Comfortable A high efficiency motor combined with a high power Ni MH battery provides you a easy and comfortable riding with excellent recreational pleasure when passing through uphills or riding against strong wind Fast Charge 2 00 00 AS The specially designed high quality charger developed by AWIN can shorten the charging time effectively in the range of 2 3 hours depending on battery capacity used GR AWIN Ni MH batteries contain no toxic heavy metals and are safer for environment than Ni cd batteries 3 AWN AWIN TECHNOLOGY CORP Specifications Dimensions 1 580mm overall length 550mm overall width 720 860mm saddle height Distance between axles wheelbase 1 070mm Tire size 20 Weight of vehicle About 28 kg Limitation of load 100 Kgs Range of assisted speed 0 25 km h Running distance of run on 1 full charge 30 60 km Maximum speed 25 km h Motor type Direct current with brushes Rated output 180W Control system PWM controlling type Power drive Chain Battery type High Performace high power Ni MH Battery Battery Capacity 24V 8Ah or 24V 12Ah Charging time 2 3 hours The running distance may vary depending on road condition weight load electrical system chosen and battery capacity used
10. putis controlled by the speed control throttle in 100 Electric Mode 4 4 AWN AWIN TECHNOLOGY CORP Maintenance and Repair Burglar proof Measures 1 Park the electric bike at a safe place such as court of the house balcony or garage 2 Lock the electric bike and take out the battery pack Lock it ona fixed position with a chain and a locking head Parking environment 1 Park the electric bike at an even road surface 2 Park the electric bike at the place with good ventilation and low humidity 3 Prevent the electric bike from exposing in the sun or wetted by the rain Periodical charge Charge the battery every 1 3 months during the storage to prevent from the shortening of its service life Saving Energy After riding the electric bike turn off the battery switch located on the battery pack for saving energy of the battery pack Tire pressure An appropriate tire pressure shall be maintained to avoid deformation of the tire Cleaning and maintenance 1 Plated metal parts The surface of the metal parts shall not be worn orlose gloss due to the cleaning 2 Metal Parts Don t remove the rust proof agent on the surface of the metal parts 3 Washing Prevent water from spilling into the chain cover motor and battery pack Lubrication Apply lubricant to the bell brake handles chain and foot support Non lubrication Don t apply lubricant to the hubs and the front and rear brake rubber parts F 15 AWN
11. rged Replace the battery when the running distance ofrun on 1 full charge is only 50 F i about one half ofa new battery pack Purchase the new battery pack fromus and recycle the used battery pack New Battery pack 5 Suggest to change the battery pack IDULISIA buluuny no of charging battery pack 44 AWN AWIN TECHNOLOGY CORP Check Before Riding A ce Check and adjust the following points before riding the electric scooter Stop riding the electric bike when any abnormality is found during the riding Contact us at 886 3 597 3688 or e mail to tsengww ms54 hinet net or any one of our authorized service centers Front handles Make sure that the front handles are fixed well Use a hexagon wrench the fix the setscrews if they are loose Pedals Make sure that the setscrews of the foot pedals are fixed tightly Seat Adjust the height ofthe pedals to fit the height of the rider Front rear wheels Make sure that the setscrews of the front rear wheels are fixed tightly Head light Push the press lever before using the head light to make the friction roller contact with the tire Battery pack Make sure that the position of the battery pack is correct and the residual capacity of the battery pack is enough O O0 OOUU L 3 1 2 AWN AW TECHNOLOGYCORP Check Before Riding A sae Check and adjust the following points before riding the electric scooter Stop riding the electr
12. ully charged Yellow blinks Detecting incorrect connection or abnormal detected tightly the charging plug of the charger to the charging socket of the battery pack 3 Use 110V or 220VAC Power for the charging Make sure that the plug Is inserted inthe socket correctly before turning onthe power switch of the charger 4 The red indicator lights when the power switch of the charger is turned on The yellow indicator then blinks CN for about 5 seconds to detect the charging environment O The charger is in a quick charging state when the yellow indicator lights continuously 5 The charging may be completed within 2 3 hours Unplug the power cable E a 4 0 AWN AWN TECHNOLOGY CORP Charge Method 3 Charging Instructions 1 Charge the battery pack before riding Charge the battery pack for at least 30 minutes before using the bike for the first time 2 Charge interval Charge the battery pack when the Red indicators blinking Charge the battery pack after the electric bike is not be used for a long period 100 75 50 30 Lessthan Charge Charge the battery pack every 1 3 Power Power 20 Power immediately months during the storage to prevent from the shortening of its service life 3 Replacement of battery pack When youride the electric bike three indicators lightand indicate that the battery is fully cha
Download Pdf Manuals
Related Search