Cordless Angle Grinder
Contents
1. WARNING It should never be necessary to force the tool The weight of the tool applies adequate pressure Forcing and excessive pressure could cause dangerous wheel breakage ALWAYS replace wheel if tool is dropped while grinding NEVER bang or hit grinding disc or wheel onto work Avoid bouncing and snagging the wheel especially when working corners sharp edges etc This can cause loss of control and kickback NEVER use tool with wood cutting blades and other sawblades Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury CAUTION Make the depth of a single cut up to 5 mm Adjust pressure on the tool so that the tool does not slow down during the operation After operation always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down If the tool is operated continuously until the battery cartridge has discharged allow the tool to rest for 15 minutes before proceeding with a fresh battery Grinding and sanding operation AS B ALWAYS hold the tool firmly with one hand on housing and the other on the side handle Turn the tool on and then apply the wheel or disc to the workpiece In general keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface During the break in period with a new wheel do not work the grinder in the B direction or it will cut into the workpiece Once th2. e Tr a k ta Grinder 007214 ENGLISH Original instructions SPECIFICATIONS Model DGA402 DGA450 DGA452 Wheel diameter 100 mm 115mm Max wheel thickness 6 4mm 6 4mm 6 4mm Spindle thread M10 M14 or 5 8 country specific Rated speed n No load speed no 11 000 min Overall length 317 mm Net weight 2 2kg 2 2kg 2 3kg Rated voltage D C 18 V D C 144 V D C 18 V Due to our continuing program of research and development the specifications herein are subject to change without notice Specifications and battery cartridge may differ from country to country Weight with battery cartridge according to EPTA Procedure 01 2003 END221 4 Symbols The following show the symbols used for the equipment Be sure that you understand their meaning before use ST Read instruction manual ww E Cd gt Ni MH Li ion Wear safety glasses Only for EU countries Do not dispose of electric equipment or battery pack together with household waste material In observance of the European Directives on Waste Electric and Electronic Equipment and Batteries and Accumulators and Waste Batteries and Accumulators and their implementation in accordance with national laws electric equipment and batteries and battery pack s that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility ENE048 1 Intend
3. Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards Power tool use and care 17 18 19 20 21 Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools 22 23 Keep cutting tools sharp and clean Properly m
4. Replace when they wear down to the limit mark Keep the carbon brushes clean and free to slip in the holders Both carbon brushes should be replaced at the same time Use only identical carbon brushes Insert the top end of slotted bit screwdriver into the notch in the tool and remove the holder cap cover by lifting it up 1 Holder cap cover 2 Screwdriver Use a screwdriver to remove the brush holder caps Take out the worn carbon brushes insert the new ones and secure the brush holder caps 1 Brush holder cap 2 Screwdriver Reinstall the holder cap cover on the tool To maintain product SAFETY and RELIABILITY repairs any other maintenance or adjustment should be performed by Makita Authorized Service Centers always using Makita replacement parts OPTIONAL ACCESSORIES ACAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita Service Center Wheel guard wheel cover For depressed center wheel multi disc Wheel guard wheel cover For abrasive cut off wheel diamond wheel Depressed center wheels Abrasive cut off wheels Multi discs Diamond wheels Wire cup brushes Wire bevel brush 85 Abrasive discs Inner
5. f Use extra caution when making a pocket cut into existing walls or other blind areas The protruding wheel may cut gas or water pipes electrical wiring or objects that can cause kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for a Do not use excessively oversized sanding disc paper Follow manufacturers recommendations when selecting sanding paper Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging tearing of the disc or kickback Wire Brushing Operations a Be aware that wire bristles are thrown by the brush even during ordinary operation Do not overstress the wires by applying excessive load to the brush The wire bristles can easily penetrate light clothing and or skin b If the use of a guard is recommended for wire brushing do not allow interference of the wire wheel or brush with the guard Wire wheel or brush may expand in diameter due to work load and centrifugal forces Additional Safety Warnings 16 20 When using depressed centre grinding wheels be sure to use only fiberglass reinforced wheels NEVER USE Stone Cup type wheels with this grinder This grinder is not designed for these types of wheels and the use of such a product may result in serious personal injury Be careful not to damage the spindle the flange especially the installing surface or the lock nut Damage to these parts could res
6. completely worn out The battery cartridge can explode in a fire Be careful not to drop or strike battery Do not use a damaged battery Follow your local regulations relating to disposal of battery SAVE THESE INSTRUCTIONS Tips for maintaining maximum battery life 1 Charge the battery before completely discharged Always stop tool operation and charge the battery cartridge when you notice less tool power Never recharge a fully charged battery cartridge Overcharging shortens the battery service life Charge the battery cartridge with room temperature at 10 C 40 C 50 F 104 F Let a hot battery cartridge cool down before charging it Charge the battery cartridge once in every six months if you do not use it for a long period of time cartridge FUNCTIONAL DESCRIPTION ACAUTION Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool Installing or removing battery cartridge 1 Button 2 Red indicator 3 Battery cartridge ACAUTION Always switch off the tool before installing or removing of the battery cartridge Hold the tool and the battery cartridge firmly when installing or removing battery cartridge Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury To remove the battery cartridge
7. flange Lock nut for depressed center wheel abrasive cut off wheel multi disc diamond wheel Lock nut for abrasive disc Lock nut wrench Side grip Makita genuine battery and charger NOTE Some items in the list may be included in the tool package as standard accessories They may differ from country to country Makita Corporation Anjo Aichi Japan 885268A223 www makita com
8. agged or pinched by the workpiece the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out The wheel may either jump toward or away from the operator depending on direction of the wheel s movement at the point of pinching Abrasive wheels may also break under these conditions Kickback is the result of power tool misuse and or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below a Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces Always use auxiliary handle if provided for maximum control over kickback or torque reaction during start up The operator can control torque reactions or kickback forces if proper precautions are taken b Never place your hand near the rotating accessory Accessory may kickback over your hand c Do not position your body in the area where power tool will move if kickback occurs Kickback will propel the tool in direction opposite to the wheel s movement at the point of snagging d Use special care when working corners sharp edges etc Avoid bouncing and snagging the accessory Corners sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback e Do not attach a saw chain woodcarving blade or toothed saw blade Such blades create frequent kickback and
9. aintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation Battery tool use and care 24 25 26 27 Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irritation or burns Service 28 29 30 Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Fol
10. ay be different WARNING The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time ENH101 16 For European countries only EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine s Designation of Machine Cordless Angle Grinder Model No Type DGA450 DGA452 are of series production and Conforms to the following European Directives 2006 42 EC And are manufactured in accordance with the following standards or standardised documents EN60745 The technical documentation is kept by Makita International Europe Ltd Technical Department Michigan Drive Tongwell Milton Keynes Bucks MK15 8JD England 30 1 2009 AR Tomoyasu Kato Director Makita Corporation 3 11 8 Sumiyoshi cho Anjo Aichi 446 8502 JAPAN GEA006 2 General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for futur
11. beyond immediate area of operation Hold the power tool by insulated gripping surfaces only when performing an operation where the cutting tool may contact hidden wiring Contact with a live wire will also make exposed metal parts of the power tool live and could give the operator an electric shock 11 Never lay the power tool down until the accessory has come to a complete stop The spinning accessory may grab the surface and pull the power tool out of your control 12 Do not run the power tool while carrying it at your side Accidental contact with the spinning accessory could snag your clothing pulling the accessory into your body 13 Regularly clean the power tool s air vents The motor s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards 14 Do not operate the power tool near flammable materials Sparks could ignite these materials 15 Do not use accessories that require liquid coolants Using water or other liquid coolants may result in electrocution or shock Kickback and Related Warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel backing pad brush or any other accessory Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory s rotation at the point of the binding For example if an abrasive wheel is sn
12. ccessory must fit the locating diameter of the flange Accessories that do not match the mounting hardware of the power tool will run out of balance vibrate excessively and may cause loss of control Do not use a damaged accessory Before each use inspect the accessory such as abrasive wheels for chips and cracks backing pad for cracks tear or excess wear wire brush for loose or cracked wires If power tool or accessory is dropped inspect for damage or install an undamaged accessory After inspecting and installing an accessory position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no load speed for one minute Damaged accessories will normally break apart during this test time Wear personal protective equipment Depending on application use face shield safety goggles or safety glasses As appropriate wear dust mask hearing protectors gloves and workshop apron capable of stopping small abrasive or workpiece fragments The eye protection must be capable of stopping flying debris generated by various operations The dust mask or respirator must be capable of filtrating particles generated by your operation Prolonged exposure to high intensity noise may cause hearing loss Keep bystanders a safe distance away from work area Anyone entering the work area must wear personal protective equipment Fragments of workpiece or of a broken accessory may fly away and cause injury
13. e edge of the wheel has been rounded off by use the wheel may be worked in both A and B direction Operation with abrasive cut off diamond wheel optional accessory Lock nut Abrasive cut off wheel diamond wheel 3 Inner flange 4 Wheel guard for abrasive cut off wheel diamond wheel Na The direction for mounting the lock nut and the inner flange varies by wheel thickness Refer to the table below 100 mm 4 Abrasive cut off wheel Diamond wheel Thickness Less than 4 mm 5 32 Thickness 4 mm AA or more Thickness Less than 4 mm 5 32 Thickness 4 mm 5 32 or more i EA SS gt lt gt 16 mm oe 16 mm 5 8 20 mm 13 16 20 mm 13 16 3 Si 1 Lock nut 2 Abrasive cut off wheel 3 Inner flange 4 Diamond wheel 115 mm 4 1 2 125 mm 5 Abrasive cut off wheel Diamond wheel Be Thickness Less than 4 mm 5 32 Thickness 4 mm 5 32 or more Thickness Less than 4 mm 5 32 Thickness 4 mm 5 32 or more et 1 _ S SO gt 22 23 mm 7 8 22 23 mm 7 8 22 23 mm 7 8 22 23 mm 7 8 a E 3 1 1 Lock nut 2 Abrasive cut off wheel 3 Inner flange 4 Diamond wheel 11 WARNING When using an abrasive cut off diamond wheel be sure to use only the special wheel guard designed for use with cut off wheels In European countries when using a diamond wh
14. e reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool Work area safety 1 Keep work area clean and well lit Cluttered or dark areas invite accidents 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes 3 Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety 4 Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock 5 Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded 6 Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock 7 Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock 8 When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of
15. ed to any lateral pressure on any materials SAVE THESE INSTRUCTIONS ZA WARNING DO NOT let comfort or familiarity with product gained from repeated use replace strict adherence to safety rules for the subject product MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1 Before using battery cartridge read all instructions and cautionary markings on 1 battery charger 2 battery and 3 product using battery 10 Do not disassemble battery cartridge If operating time has become excessively shorter stop operating immediately It may result in a risk of overheating possible burns and even an explosion If electrolyte gets into your eyes rinse them out with clear water and seek medical attention right away It may result in loss of your eyesight Do not short the battery cartridge 1 Do not touch the terminals with any conductive material 2 Avoid storing battery cartridge in a container with other metal objects such as nails coins etc 3 Do not expose battery cartridge to water or rain A battery short can cause a large current flow overheating possible burns and even a breakdown Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 C 122 F Do not incinerate the battery cartridge even if it is severely damaged or is
16. ed use The tool is intended for grinding sanding and cutting of metal and stone materials without the use of water ENG905 1 Noise The typical A weighted according to EN60745 noise level determined Model DGA450 Sound pressure level Lpa 74 dB A Uncertainty K 3 dB A The noise level under working may exceed 80 dB A Model DGA452 Sound pressure level Lpa 76 dB A Uncertainty K 3 dB A The noise level under working may exceed 80 dB A Wear ear protection ENG900 1 Vibration The vibration total value tri axial determined according to EN60745 vector sum Model DGA450 Work mode surface grinding Vibration emission anac 8 5 m s Uncertainty K 1 5 m s Work mode disc sanding Vibration emission aps 2 5 m s or less Uncertainty K 1 5 m s Model DGA452 Work mode surface grinding Vibration emission a ac 10 0 m s Uncertainty K 1 5 m s Work mode disc sanding Vibration emission apps 2 5 m s or less Uncertainty K 1 5 m s ENG902 1 The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another The declared vibration emission value may also be used in a preliminary assessment of exposure The declared vibration emission value is used for main applications of the power tool However if the power tool is used for other applications the vibration emission value m
17. eel the ordinary guard can be used NEVER use cut off wheel for side grinding Do not jam the wheel or apply excessive pressure Do not attempt to make an excessive depth of cut Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback wheel breakage and overheating of the motor may occur Do not start the cutting operation in the workpiece Let the wheel reach full speed and carefully enter into the cut moving the tool forward over the workpiece surface The wheel may bind walk up or kickback if the power tool is started in the workpiece During cutting operations never change the angle of the wheel Placing side pressure on the cut off wheel as in grinding will cause the wheel to crack and break causing serious personal injury A diamond wheel shall be operated perpendicular to the material being cut MAINTENANCE CAUTION Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance Never use gasoline benzine thinner alcohol or the like Discoloration deformation or cracks may result 1 Exhaust vent 2 Inhalation vent The tool and its air vents have to be kept clean Regularly clean the tool s air vents or whenever the vents start to become obstructed Replacing carbon brushes 1 Limit mark Remove and check the carbon brushes regularly
18. electric shock 9 If operating a power tool in a damp location is unavoidable use a ground fault circuit interrupter GFCI protected supply Use of an GFCI reduces the risk of electric shock Personal safety 10 Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under 11 12 13 14 15 16 the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use personal protective equipment Always wear eye protection Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries Prevent unintentional starting Ensure the switch is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts
19. emove and recharge the battery NOTE The overheat protection works only with a battery cartridge with a star mark 1 Star marking Indication lamps are located in two positions When the battery cartridge is inserted on the tool with the slide switch positioned in the O OFF the indication lamp flickers quickly for approximately one second If it does not flicker so the battery cartridge or indication lamp may be broken Overload protection When the tool becomes overloaded the indication lamp lights up When the load on the tool is reduced the lamp goes out If the tool continues to be overloaded and the indication lamp continues to light up for approximately two seconds the tool stops This prevents the motor and its related parts from being damaged In this situation move the slide switch to the O OFF position once And then move it to the I ON position again to restart Battery cartridge replacing signal When the remaining battery capacity is low the indicator lamp lights up during operation earlier than that of high battery capacity Accidental re start preventive function Even if the battery cartridge is inserted on the tool with the slide switch in the I ON position the tool does not start In this situation the lamp flickers slowly It indicates that the accidental re start preventive function is at work To start the tool first slide the slide switch toward the O OFF posit
20. ion and then slide it toward the I ON position Shaft lock 1 Shaft lock CAUTION Never actuate the shaft lock when the spindle is moving The tool may be damaged Press the shaft lock to prevent spindle rotation when installing or removing accessories Switch action 1 Slide switch A CAUTION Before inserting the battery cartridge into the tool always check to see that the slide switch actuates properly and returns to the OFF position when the rear of the slide switch is depressed To start the tool slide the slide switch toward the I ON position For continuous operation press the front of the slide switch to lock it To stop the tool press the rear of the slide switch then slide it toward the O OFF position ASSEMBLY ACAUTION Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool Installing side grip handle ACAUTION Always be sure that the side grip is installed securely before operation Screw the side grip securely on the position of the tool as shown in the figure Installing or removing wheel guard For depressed center wheel multi disc abrasive cut off wheel diamond wheel For tool with locking screw type wheel guard 1 Wheel guard 2 Bearing box 3 Screw Z WARNING When using a depressed center grinding wheel Multi disc flex wheel wire wheel brush cut off wheel
21. loss of control Safety Warnings Specific for Grinding and Abrasive Cutting Off Operations a Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe b The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected c The guard must be securely attached to the power tool and positioned for maximum safety so the least amount of wheel is exposed towards the operator The guard helps to protect the operator from broken wheel fragments accidental contact with wheel and sparks that could ignite clothing d Wheels must be used only for recommended applications For example do not grind with the side of cut off wheel Abrasive cut off wheels are intended for peripheral grinding side forces applied to these wheels may cause them to shatter e Always use undamaged wheel flanges that are of correct size and shape for your selected wheel Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage Flanges for cut off wheels may be different from grinding wheel flanges f Do not use worn down wheels from larger power tools Wheel intended for larger power tool is not suitable for the higher speed of a smaller to
22. low instruction for lubricating changing accessories Keep handles dry clean and free from oil and grease and GEB059 3 CORDLESS GRINDER SAFETY WARNINGS Safety Warnings Common for Grinding Sanding Wire Brushing or Abrasive Cutting Off Operations 1 This power tool is intended to function as a grinder sander wire brush or cut off tool Read all safety warnings instructions illustrations and specifications provided with this power tool Failure to follow all instructions listed below may result in electric shock fire and or serious injury Operations such as polishing are not recommended to be performed with this power tool Operations for which the power tool was not designed may create a hazard and cause 10 personal injury Do not use accessories which are not specifically designed and recommended by the tool manufacturer Just because the accessory can be attached to your power tool it does not assure safe operation The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool Accessories running faster than their rated speed can break and fly apart The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool Incorrectly sized accessories cannot be adequately guarded or controlled Threaded mounting of accessories must match the grinder spindle thread For accessories mounted by flanges the arbour hole of the a
23. ol and may burst Additional Safety Warnings Specific for Abrasive Cutting Off Operations a Do not jam the cut off wheel or apply excessive pressure Do not attempt to make an excessive depth of cut Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage b Do not position your body in line with and behind the rotating wheel When the wheel at the point of operation is moving away from your body the possible kickback may propel the spinning wheel and the power tool directly at you c When wheel is binding or when interrupting a cut for any reason switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop Never attempt to remove the cut off wheel from the cut while the wheel is in motion otherwise kickback may occur Investigate and take corrective action to eliminate the cause of wheel binding d Do not restart the cutting operation in the workpiece Let the wheel reach full speed and carefully re enter the cut The wheel may bind walk up or kickback if the power tool is restarted in the workpiece e Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback Large workpieces tend to sag under their own weight Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel
24. or diamond wheel the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator When using an abrasive cut off diamond wheel be sure to use only the special wheel guard designed for use with cut off wheels In European countries when using a diamond wheel the ordinary guard can be used Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box Then rotate the wheel guard to such an angle that it can protect the operator according to work Be sure to tighten the screw securely To remove wheel follow the installation procedure in reverse guard Installing or removing depressed center grinding wheel Multi disc 1 Lock nut 2 Depressed center grinding wheel Multi disc 3 Inner flange ZAWARNING Always use supplied guard when depressed center grinding wheel Multi disc is on tool Wheel can shatter during use and guard helps to reduce chances of personal injury Mount the inner flange onto the spindle Fit the wheel disc on the inner flange and screw the lock nut onto the spindle To tighten the lock nut press the shaft lock firmly so that the spindle cannot revolve then use the lock nut wrench and securely tighten clockwise 1 Lock nut wrench 2 Shaft lock To remove the wheel follow the installation procedure in reverse WARNING Only actuate the shaft lock when the spindle is not moving OPERATION
25. slide it from the tool while sliding the button on the front of the cartridge To install the battery cartridge align the tongue on the battery cartridge with the groove in the housing and slip it into place Insert it all the way until it locks in place with a little click If you can see the red indicator on the upper side of the button it is not locked completely ACAUTION Always install the battery cartridge fully until the red indicator cannot be seen If not it may accidentally fall out of the tool causing injury to you or someone around you Do not install the battery cartridge forcibly If the cartridge does not slide in easily it is not being inserted correctly Battery protection system The tool is equipped with a battery protection system This system automatically cuts off power to the motor to extend battery life The tool will automatically stop during operation if the tool and or battery are placed under one of the following conditions Overloaded The tool is operated in a manner that causes itto draw an abnormally high current In this situation turn the tool off and stop the application that caused the tool to become overloaded Then turn the tool on to restart If the tool does not start the battery is overheated In this situation let the battery cool before turning the tool on again Low battery voltage The remaining battery capacity is too low and the tool will not operate In this situation r
26. ult in wheel breakage Make sure the wheel is not contacting the workpiece before the switch is turned on Before using the tool on an actual workpiece let it run for a while Watch for vibration or 21 22 23 24 25 26 27 28 29 30 31 32 33 wobbling that could indicate poor installation or a poorly balanced wheel Use the specified surface of the wheel to perform the grinding Do not leave the tool running Operate the tool only when hand held Do not touch the workpiece immediately after operation it may be extremely hot and could burn your skin Observe the instructions of the manufacturer for correct mounting and use of wheels Handle and store wheels with care Do not use separate reducing bushings or adaptors to adapt large hole abrasive wheels Use only flanges specified for this tool For tools intended to be fitted with threaded hole wheel ensure that the thread in the wheel is long enough to accept the spindle length Check that the workpiece is properly supported Pay attention that the wheel continues to rotate after the tool is switched off If working place is extremely hot and humid or badly polluted by conductive dust use a short circuit breaker 30 mA to assure operator safety Do not use the tool containing asbestos When use cut off wheel always work with the dust collecting wheel guard required by domestic regulation Cutting discs must not be subject
Download Pdf Manuals
Related Search