WPA CO 7500 Colorimeter User Manual
Contents
1. assembly part number 80 3000 59 and tighten the fixing screw 5 Replace the base of the instrument and tighten the 4 base plate screws Issue 02 12 2003 WPA CO 7500 English SPECIFICATION AND WARRANTY 440 470 490 520 550 580 590 and 680nm Range Absorbance 0 3A to 1 99 A Transmission O 199 T Repeatability 0 02A at 1A using cuvettes Operational modes Absorbance Transmission Kinetics Cuvette holder Fixed with drain hole Accepts 10mm pathlength semi micro and macro cuvettes or 16mm round tubes Can accept 10 12mm tubes with optional adapters 0 2V for 0 2Abs or 0 1 99V for 0 199 T via 2 x 4mm sockets 100mV offset in the output voltage RS232 Power requirements External power adaptor 110 to 220V 50 60Hz 20VA or internal rechargeable NiMH battery mains battery version only Approximate dimensions 180 x 150 x 60mm Weight 0 6kg Specifications are measured after the instrument has warmed up at a constant ambient temperature and are typical of a production unit As part of our policy of continuous development we reserve the right to alter specifications without notice The product does not fulfil the specific requirements of the IVD Warranty Your supplier guarantees that the product supplied has been thoroughly tested to ensure that it meets its published specification The warranty included in the conditions of supply is valid for 12 months only if the product has been used2. mains supply when not in use 2 Keep the instrument clean and dry immediately wipe off any spilt liquids Clean with a slightly damp cloth a non abrasive water based soap or detergent may be used 3 Remove the cuvettes from the instrument when not in use 4 Atregular intervals check the mains power adaptor and cable for wear and tear and replace if damaged 5 Store in a cool place away from corrosive chemicals or fumes Changing a filter Ultimately the filters may need replacement depending on the environment High humidity will cause the filters to fail more rapidly If a filter does have to be replaced replace the whole set part number 80 3000 58 l 2 3 Disconnect from power supply Place the instrument upside down on a soft surface and unscrew the large grey screw at the centre of the filter wheel The filter wheel can then be removed Remove the filter to be replaced by pushing the locating clip back on the underside of the filter wheel whilst pulling on the filter a large flat head screwdriver may help Insert a new filter ensuring that it clicks firmly into place Issue 02 12 2003 WPA CO 7500 English 7 Replacing the light bulb 1 Disconnect from power supply 2 Place the instrument upside down on a soft surface and remove the 4 screws in the base using a No 1 Pozidrive cross head screwdriver 3 Remove the lamp assembly fixing screw with a small flat screwdriver and unplug 4 Insert the new lamp
3. WPA CO 7500 Colorimeter User Manual Dio chrom Declaration of Conformity This is to certify that the WPA CO 7500 Colorimeter Part number 80 3000 43 mains only 80 3000 44 mains battery manufactured by Biochrom Ltd conform to the requirements of the following Directives 73 23 EEC amp 89 336 EEC Standards to which conformity is declared EN 61 010 1 2001 Safety requirements for electrical equipment for measurement control and laboratory use EN 61326 1998 Electrical equipment for measurement control and laboratory use EMC requirements Signed Dated 24th March 2003 David Parr Managing Director Biochrom Ltd Postal address Telephone Telefax Biochrom Ltd 44 1223 423723 44 1223 420164 22 Cambridge Science Park Milton Road e mail enquiries biochrom co uk website http www biochrom co uk Cambridge CB4 OFJ England Registered in England No 3526954 Registered Office 22 Cambridge Science Park Milton Road Cambridge CB4 OFJ England CONTENTS Unpacking Positioning and Installation OPERATION Introduction Using the Instrument Making an absorbance or T measurement Making a kinetics measurement TROUBLE SHOOTING NOTES ACCESSORIES CONSUMABLES AND SPARES OUTPUT OF RESULTS Use with serial printer Use with PC Use with chart recorder MAINTENANCE General maintenance Changing a filter Replacing the light bulb SPECIFICATION AND WARRANTY WO SNNN ADAH AN Vi LUNIN n Unpac
4. according to the instructions supplied They can accept no liability for loss or damage however caused arising from the faulty or incorrect use of this product This product has been designed and manufactured by Biochrom Ltd 22 Cambridge Science Park Milton Road Cambridge CB4 OFJ UK Issue 02 12 2003 WPA CO 7500 English 9 Issue 02 12 2003 WPA CO 7500 English 10
5. e button The display will show 0 00 Abs or 100 T Remove the reference sample and replace with the sample solution in a cuvette or tube Press and release the T test button The lamp will remain on the lamp indicator will flash on the display readings will be taken every 1 2 seconds and the display will then show the changes in optical density Abs or T over time The results are also output via both the RS232 and the analogue outputs To stop the readings repress the kinetics or T test button and the instrument will revert to the flash mode of operation Issue 02 12 2003 WPA CO 7500 English TROUBLE SHOOTING NOTES ERROR INDICATION SOLUTION A flashing Absorbance reading of 2 00 A is obtained A negative reading is obtained A flashing Absorbance reading of 0 30 Abs is obtained This indicates an Absorbance of more than 1 99 and which is therefore out of range The sample needs to be diluted In normal measurements the test sample has a positive Absorbance compared to that of the Reference Occasionally it can happen that the chemistry has been arranged for a coloured Reference and a less absorbing test solution 1 e one of negative Absorbance The instrument will respond correctly to negative absorbances down to 0 30 A Negative readings will also be obtained if the Reference and Test cuvettes are mixed up This indicates an Absorbance of less than 0 30 Abs and is therefore out of range The sample ne
6. ed It can be used in the 400 700 nm wavelength range as it has an integral colour coded rotating wheel containing filters at 440 470 490 520 550 580 590 and 680nm These are made from coloured gelatin and are encased in glass enabling the instrument to be used in tropical conditions A filter is selected by moving the wheel until the required wavelength is displayed in the window above the cell compartment The instrument produces stable white light that is directed through the reference and sample solutions in turn to a detector after being filtered to a single colour This colour is normally chosen to be complimentary that which is most absorbed to the test solution The amount of energy passing through the reference is deemed equivalent to 100 transmission and is compared with that through the absorbing sample measured as T normally 0 lt T lt 100 Successful measurement of concentration is dependent on arranging the chemistry and conditions to get the best agreement with the Beer Lambert Law To make full use of the instrument s excellent performance it is recommended to arrange the chemistry and dilutions to give Absorbance readings in the range 0 2 1 2A Below 0 2A the relative concentration accuracy is reduced whilst Absorbance readings above 1 2A imply concentrations of high molar strength that do not obey Beer Lambert s Law so well In addition small photometric errors become increasingly important and the effec
7. eds to be diluted Unexpected results are obtained rEF is displayed when T is pressed No reading is obtained when using the instrument is being operated by battery An abnormally high absorbance reading is obtained at one wavelength Issue 02 12 2003 Any bubbles in solution will produce considerable error Check bulb is flashing The baseline has not been set Replace the sample with a blank or reference sample and press R The samples can then be tested Check that there is sufficient battery power available The battery power available is indicted by the battery symbol at the bottom right hand corner of the display Three bars in the battery indicates that it is fully charged If only one or no bars are present the battery needs to be recharged Connect the instrument to the electric power supply using the adaptor recharge unit The battery will be recharged in 12 hours Visually check the sample to ensure that there has been no errors in the chemistry performed Check the condition of the filter Deterioration of the filter could cause higher absorbance readings WPA CO 7500 English IMPORTANT WARNING e This colorimeter has been designed for non toxic water based solutions If stronger solutions or dangerous or aggressive chemicals have to be used then they must be treated with great care and be contained in properly stoppered glass cuvettes e Never cover the end of a cuvette by the thumb or finger t
8. king Positioning and Installation e Ensure your proposed installation site conforms to the environmental conditions for safe operation Indoor use only Temperature 5 C to 35 C Maximum relative humidity of 80 up to 31 C decreasing linearly to 50 at 40 C If this equipment is used in a manner not specified or in environmental conditions not appropriate for safe operation the protection provided by the equipment may be impaired and instrument warranty withdrawn e The instrument is powered by mains electricity using the supplied power adapter Using the instrument with the mains adapter will automatically recharge the internal rechargeable battery mains battery version only e The battery will last approx 1 month when fully charged with normal use e A full battery recharge will take approx 12 hours overnight Issue 02 12 2003 WPA CO 7500 English l OPERATION Introduction Your colorimeter is a small robust easy to use instrument that has been designed with both the student user and field user in mind It is ideal for teaching the principles of science and analysis in sixth form colleges and technical schools as well as being rugged enough for measurements in for example remote location health clinics where simple diagnostic tests need to be made The instrument measures in absorbance and transmission mode as well as in simple kinetics enabling changes in absorbance over time and reaction rates to be determin
9. l 15mm 16mm diameter tube Issue 02 12 2003 WPA CO 7500 English Making an absorbance or T measurement 1 Switch the instrument on by pressing the ON OFF button Select the required wavelength by turning the thumbwheel at the side of the instrument The wavelength selected is displayed in the window above the cuvette compartment Note Two of the locations are empty Select Abs or T mode Place a reference into the cuvette compartment and press and release the R reference button The display will show 0 00 Abs or 100 T Remove the reference sample and replace with the sample solution in a cuvette or tube Press and release the T test button The result is displayed in absorbance or Transmission units Multiple samples can be compared with the same reference by placing different samples in the cuvette chamber and making measurements for each one It is recommended to re reference with the reference solution every 10 to 15 minutes to avoid any slow instrument drift If in doubt always re reference Note At high Absorbances the time taken to take a measurement will be longer up to 10 seconds as the light levels are proportionally lower Making a kinetics measurement 1 se The kinetics mode provides a continuous readout of changes in absorbance of a sample Press and release the kinetics button Select Abs or T mode Place a reference into the cuvette compartment and press and release the R referenc
10. o shake the contents e Never pipette by mouth ACCESSORIES CONSUMABLES AND SPARES S2000P serial printer includes serial cable 80 3000 94 Spreadsheet interface software 80 2112 23 Serial interface cable 80 3001 00 Pack of 100 disposable cells Iml minimum volume 80 3000 60 Pack of 100 disposable cells 0 5ml minimum volume 80 3000 76 Adapter set for 10 and 12mm tubes 80 3000 57 Spare filter set 80 3000 58 Spare lamp 80 3000 59 OUTPUT OF RESULTS Use with serial printer The instrument is designed to print to a serial printer at 9600 Baud with the S2000P serial printer and cable Output is automatic when R T is pressed and the printer is connected and switched on Use with PC Results can be downloaded directly to Excel when the PC has the Spreadsheet Interface Software installed 80 2112 23 and the two are linked with the serial cable 80 3001 00 detailed instructions are supplied with the software Baud rate is 9600 and the separator should be set to space Use with chart recorder The instrument can be connected to an analogue chart recorder using the 2 x 4 mm banana plug sockets The output is 0 2V for 0 2A and 0 1 99V for 0 199 T A standard chart recorder cable should be sourced locally Issue 02 12 2003 WPA CO 7500 English MAINTENANCE General maintenance The instrument has no serviceable parts The instrument requires little maintenance The following are considered good practice 1 Always disconnect from the
11. t of stray light will increase If it is not possible to stay within these bounds it may be desirable to make calibration curves for known concentrations and their measured Absorbances As colorimeter measurements are comparative it is essential that only the solutions themselves change This product contains a fully stabilised light source and electronics with a fixed light path The instrument can be linked via a serial lead to either a serial printer for hardcopy output or to aPC for download of results to spreadsheet It has an analogue output and can also be connected to a chart recorder to output absorbance time data when in kinetics mode Issue 02 12 2003 WPA CO 7500 English 2 Using the Instrument On off button to set reference to 0 000 OD at 600nm on a reference to make a measurement to measure kinetics To select between absorbance or Transmission Wavelength indicator There is a battery indicator Note that the light beam shines from front to back through the cell chamber ensure the cell is inserted in the correct alignment The following table indicates the absolute minimum volume necessary for the correct function of the unit The use of disposable plastic cuvettes is recommended Cuvette Tube Min Volume Partnumber Minimum Depth approx from ml base of cuvette to meniscus mm on max fill volume 4 5ml max fill volume 1 4ml 10mm diameter tube 0 9ml 16mm 12mm diameter tube 1 1m
Download Pdf Manuals
Related Search