SD2620W Stereoscopic Monitor User`s Guide
Contents
1. Top Monitor Dual Output Graphics Card Computer and Software Application Driving the StereoMirror monitor User s Guide 3 Getting Started Read all instructions before assembling the monitor Improper assembly can result in damage to the display components Assemble the unit 1 Remove the bottom monitor assembly from the shipping box and place it on a sturdy table or desktop To keep the display surface clean avoid touching the screen Remove the top monitor assembly from the shipping box Loosen the two screws on the cover of the cable management compartment and remove the cover Slide the aluminum flanges of the upper assembly into the holes on the cross bracket of the bottom monitor assembly until fully seated Continue to support the top monitor assembly and tighten the four thumb screws 4 SD2620W 4 Thread the cables from the top monitor through the rectangular hole in the cross bracket 5 Replace the top and bottom cable covers if desired 6 Remove the beamsplitter from the shipping case With the StereoMirror logo oriented to the lower right insert the pins located on either side of the mirror frame into the corresponding slots on the mirror support arms The pins should rest in the fully forward position of the mounting arm slots User s Guide 5 Select a graphics card The SD2620W unit requires a dual output graphics card to drive the two mon2. DDC CI allows you to control certain settings of the monitor via computer Default is ON When Full is not selected in the Expansion Mode and the resolution is under the LCD panel native resolution the picture does not display at full screen The borders sides around the picture can be customized CLIL Adjust Side Color to customize the color of the border sides around the picture Reset all user settings to factory preset value except language selection Select a language for OSD menu Control the location of the OSD menu on the screen Factory setting Center of the screen Select OSD Menu turn off time Factory setting 45 seconds Resolution notifier activity Factory setting OFF User s Guide 15 D SUB INPUT 1920X1200 60 0Hz VER 1 OOXXXXO DVI I NPUT 1920X1200 60 OHzZ VER 1 QOXXXXO VIDEO INPUT D SUB INPUT VIDEO INPUT DYI INPUT VIDEO INPUT D SUB INPUT amp NO SIGNAL VIDEO INPUT DYI INPUT amp NO SIGNAL 16 SD2620W FUNCTION INFORMATION INPUT SELECT OSD WARNING NO SIGNAL FUNCTION DESCRIPTION Provide information about resolution H V frequencies and polarity of the input signal This OSD reports the current signal being displayed This OSD will automatically turn off after 2 seconds you can also press the Exit key to close it This OSD gives a warning when the selected input signal is not active After power on or when the
3. PLANAR SD2620VV Stereoscopic Monitor USER S GUIDE www planar3d com Planar Systems Inc 1195 NW Compton Drive Beaverton OR 97006 1992 www planar com 2008 Planar Systems Inc Planar and the Planar logo are registered trademarks of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subject to change without notice 02 08 Usage Notice A To prevent the risk of fire or shock hazards do not expose this product to rain or moisture Do not open or disassemble the product as doing so may cause electric shock Follow all warnings precautions and maintenance as recommended in this user s guide to maximize the life and performance of your unit Do Turn off the monitors before cleaning Use only a dry soft cloth or clean room wipe when cleaning the LCD panel surface or the half mirror Use a soft cloth moistened with water and or mild detergent to clean the display housing and stand Use only high quality and safety approved AC DC power adapters Disconnect the power plug from the grounded AC outlet if the product will not be used for a long period of time Don t Do not touch the LCD panel or half mirror surfaces with sharp or hard objects Do not use abrasive cleaners waxes or solvents for your cleaning Do not operate the product under these conditions In an extremely hot cold or humid environment In a
4. e Geophysical modeling e Molecular modeling e Computer games e Oil and gas exploration e Architecture and mechanical design e Stereo photography or videography e Medical imaging not as yet FDA 510 k approved e Surgical planning e Teaching of anatomy e Simulation e Complex data analysis The StereoMirror monitor f For some individuals prolonged use of any stereoscopic monitor may cause discomfort Take a break from stereo viewing if you sense eye fatigue Individuals who are unaccustomed to using stereoscopic 3D monitors may require a period of adaptation User s Guide 1 StereoMirror Technology A StereoMirror monitor consists of two AMLCD Active Matrix Liquid Crystal Display units oriented at a 110 angle and mounted on a specially designed stand A passive beamsplitter mirror bisects the angle formed between the two monitors and there is a fine mechanical adjustment for the mirror angle between the two displays One side of the glass mirror has a reflective coating and the other side has an anti reflective coating to minimize secondary reflections The mirror has been treated with a hard top coating to accommodate cleaning In general the objective of a stereoscopic display is to efficiently present a left el oft Eye eye image P ee Te il Image solely to the ae P fre left eye while eae the right eye image is directed to the right eye This allows the human visual system to merge th
5. input signal becomes inactive this warning appears No signal OSD is shown after 0 5 seconds from video mode detection This OSD turns off automatically after 5 seconds or when you press the Exit key It then changes to the power saving mode If the direction key is pressed during power saving mode this warning OSD opens again MENU VIDEO INPUT D SUB INPUT amp OUT OF RANGE VIDEO INPUT DYI INPUT amp OUT OF RANGE AUTO ADJUST PROCEEDING FUNCTION OSD WARNING OUT OF RANGE AUTO ADJUST Analog Input Only Target Color Coordinates COLOR TEMPERATURE 9300K 0 189 0 446 0 283 0 297 Power Management This LCD monitor complies with the VESA DPM Power Management guidelines The VESA DPM provides a power saving mode through detection of a horizontal or vertical sync signal A green power indicator light means the monitor has a signal and is working properly When the LCD monitor is in power saving mode the monitor screen is blank and the power LED indicator light is amber The monitor is powered off when the LED power indicator is dark FUNCTION DESCRIPTION This function gives warning for an input resolution or refresh rate that the monitor cannot display If video signal is not at the proper timing when the monitor powers on or when the input signal is changed this message opens It disappears after 45 seconds or when you press the Exit key When the monitor is displayed for
6. one 12 foot DVI cable and one 14 inch DVI cable 1 Plug one end of the 6 foot DVI cable into the primary port of the dual channel DVI graphics card Plug the other end into the bottom monitor of the SD2620W unit Plug one end of the 14 inch DVI cable into the secondary output of the dual channel graphics card Plug the other end into the input port labeled IN of the mirror flip PCI card Plug one end of the 12 foot DVI cable into the output port of the mirror flip PCI card labeled OUT Plug the other end into the top monitor of the SD2620W unit Short DVI cable installed A The two monitors must be connected with an off the shelf video cable to comply with FCC regulations Ferrite core interface cables are provided This device will not be in compliance with FCC regulations when a non ferrite core video cable is used User s Guide 7 Connect the power cords Two power cords are shipped with the unit Use only the power cords supplied with the unit 1 Plug the 10 foot cord into the AC power jack of the top monitor Plug the 6 foot cord into the bottom monitor Then plug the power connectors into a grounded outlet 2 Turn on the power toggle switch on the back and the soft power switch on the front bezel of each of the two LCD monitors 3 Power up the computer Check the alignment Although the SD2620W unit is aligned during manufacturing it may require realignment after reassembly
7. the first time and the resolution is 800x600 or above the monitor makes an auto adjustment To manually execute the Auto Adjust function press the Auto button 7500K sRGB 0 194 0 198 0 459 0 468 0 299 0 313 0 315 0 329 User s Guide 17 OSD Lock Out Function OSD Lock Function allows you to lock out the OSD menu and De the button keys To activate the 1920X1200 60 OHz OSD lock function the monitor VER 1 00XXXXO must be in a normal display mode with the information menu activated Then follow the instructions below D SUB INPUT Option 1 OSD lock All buttons except the Power button are locked Press Exit key Menu key Soft power key at same time The monitor shows an OSD VIDEO INPUT Lock Out message The Power button can be used to turn the monitor on or off however the i OSD LOCK OUT other menu buttons will not be functional and a warning message will be displayed Repeat the option key strokes to unlock the OSD menu Option 2 OSD amp Power button lock All buttons including the Power button are locked Press Exit key Menu key Up key at same time The monitor shows a Lock Out VIDEO INPUT message The message will be shown when any button is pressed Press any menu amp LOCK OUT control button to close this message Repeat the option key strokes to unlock the OSD menu and Power button 18 SD2620W Monitor Specifications Displays 500 cd m typical 400
8. ar Systems The case features a tough plastic shell locks customized foam inlay and wheels Additional polarized glasses are available from Planar in three styles Captain Terminator and Spring Clip for attaching to prescription glasses Contact Planar via the web site www planar3d com or call toll free at 1 866 475 2627 Accessories can also be purchased through Planar resellers User s Guide 21 Troubleshooting Problem Possible Solution No image appears on the screen e Check that all the power cord connections are secure e Check that the power buttons on the side and front of both monitors are switched on and that the power indicator light is green e Check that the DVI cables are securely fastened to the graphics card the mirror flip PCI card and the two monitors e Make sure that the pins of the DVI connectors are not bent or broken Partial image or incorrectly displayed image e Check to see if the resolution of the computer graphics card is higher than that of the LCD panels 1920 x 1200 e Check to see that the output timing of the video signals is within the synchronous range of the LCD panels horizontal 31 93 kHz vertical 50 76 Hz The Input Not Supported message appears on the screen if the timing is not supported by the LCD panel Both displays work but there is no stereo functionality The stereoscopic Be certain the graphics card is properly set up
9. at your site There are two fine adjustment screws located on the mirror support arms Rotating these screws raises or lowers the beamsplitter mirror Adjust the screws so that the corners of the reflected image of the upper monitor are aligned with the corners of the transmitted image from the lower monitor You may want to use a test image during the alignment process A sample is available at www planar3d com Perfect alignment between the two images is not required for stereo viewing The human visual system is typically adept at fusing two images that are slightly shifted relative to each other This is especially true for horizontal alignment In a careful manner try to achieve vertical alignment as closely as possible Coarse vertical misalignment can cause eye fatigue or headaches since the eyes are accustomed to seeing stereo images from the same vertical position 8 SD2620W Product Use Operating in 2D mode Your SD2620W unit can operate either as a 3D stereoscopic monitor or in the standard 2D mode Converting to 2D viewing can be accomplished by either turning off the power to one of the monitors or by putting the mirror into the locked upright position To move the mirror to the raised position use two hands to slide it up the mirror support arms and then raise it until it drops into the locked position To lower the mirror use two hands to lift it out of the locked slot and then lower it down onto the fine StereoMir
10. ay esesesesessesesesesessesesesesesessesesesesossesesesesosoeseses 11 target Color Coordinates ememtmcomteamemtemmmsntmbmcmt oest tats 17 Power Management mmtmmmmssamttemdmntmeteiute nm 17 OSD Lock QUE FUNCTIO Misionin 18 Monitor SDECIT ICAU ONS senten cate 19 SVS SICA Sched aces sess cases lat eet otha es eel ation saad een a eae uae 21 Software COMA Des us tea at auedomttments 21 ACCESSO NES ira 21 TOUDIESR OO UN Oi coet a E T a 22 Warranty saccade Cio te E A E A cacomtt end ti 23 Product Registratlon semen T ens 23 CRINRECVEl Os ic AEA EE dotats 24 Important Recycle Instructions essesesesesesseseseseseseesesesesesossesesesesesesesesesesseseseee 24 vi SD2620W Stereoscopic Viewing We live in a three dimensional world The human visual system can process the slightly different views of the world and translate the views into the perception of depth This process is called stereopsis In the last two centuries much effort has been devoted to the reproduction of depth perception primarily with photography and more recently with computer graphic images Stereoscopic 3D viewing can help a viewer make faster more accurate and more enjoyable interpretations of imagery The SD2620W StereoMirror monitor in particular creates an unprecedented level of stereo 3D viewing quality and viewer comfort Stereo viewing is useful for the following applications e Photogrammetry and remote sensing e Geospatial image analysis
11. cd m minimum Power consumption 135 W max per monitor 270 W total 4 W total standby Product approvals UL cUL CE FCC B TUV GS MTBF 50 000 hours at 40 C Video Input signal Analog VGA Digital 24 pin DVI D Input impedance 75 Ohm 2 VGA Sync input signal Digital TMDS separate TTL compatible horizontal and vertical synchronization Polarity Positive negative Vertical refresh 60 Hz Digital 50 76 Hz Analog User s Guide 19 Plug and Play The unit supports the VESA DDC2B functions of Plug and Play Environment Operating conditions Temperature 5 C 40 C 41 F 104 F Operating conditions Relative humidity 20 to 80 non condensing Storage conditions Temperature 20 C to 60 C 4 F to 140 F Storage conditions Relative humidity 5 to 85 non condensing Size and weight 546 mm 754 mm La 588 mm La 206 mm Dimensions of monitor unit front and side 20 SD2620W System Care Monitors Turn off the monitors before cleaning Use a dry soft cloth clean room wiper or compressed air when cleaning the LCD panel surface A soft cloth moistened with water and or mild detergent can be used to clean the display housing and stand Do not touch the LCD panel surfaces with sharp or hard objects Do not use abrasive cleaners waxes or solvents for cleaning Mirror Use a dry soft cloth clean room wiper or compressed air when cleaning the mirror
12. e two images and results in the perception of depth or stereopsis In the StereoMirror design this stereo separation is achieved using the principle of conservation of polarization Upper LCD Right Eye Image Beamsplitter Lower LCD Half Mirror Operating principle of the StereoMirror monitor Liquid crystal displays operate based on the ability of liquid crystal material to modulate plane polarized light The two AMLCDs in the SD2620W model have been manufactured so that the polarized light emitted from the top monitor is 90 rotated from that of the bottom monitor The image from the lower monitor is seen through the mirror as shown in the illustration above When stereo pair images from the two monitors are viewed through crossed polarizing glasses glasses with polarizing films mounted on the eyepieces with their planes of polarization at a right angle to one another the user only sees the left eye image with the eyepiece having the 90 oriented polarizer and the right eye image with the eyepiece having the 0 polarizer Light with a perpendicular polarization is not transmitted The result is a single fused stereoscopic image 2 SD2620W A block diagram describing the process of driving a StereoMirror monitor with a computer is shown below The left eye and right eye images are sent to their respective AMLCDs independently and without any special treatment with the exception of accommodating for the fact t
13. ect among functions shown on the OSD menu The menu has been designed for easy user viewing environments OSD function menu To activate the OSD main menu press the Menu button The menu diagram pops up on the screen as shown Use the 4D 1 key to navigate to the function you want to adjust Push the 4D 1 key to enter a submenu and adjust the value Push the 4D 1 key again to exit the submenu Press the Exit button to close the OSD menu at any time Press the Menu key to return to the main menu f Firmvvare revision may have been updated into the latest version while the version number shown on the information item in the OSD menu may have remained version 1 User s Guide 11 Function description Tables on the following pages describe all the functions on the OSD menus PRESS CENTER OR SELECT TO ADJUST 12 SD2620W FUNCTION DV MODE BRIGHTNESS CONTRAST SHARPNESS AUTO CONTRAST Analog Input only AUTO ADJUST Analog Input only FUNCTION DESCRIPTION This DV mode display setting can be selected by OSD STANDARD TEXT sRGB MOVIE GAMING PHOTO Default setting TEXT Adjust the brightness Factory setting 100 0 Adjust the image contrast Factory setting 50 0 Adjust the sharpness Factory setting 50 Adjust the CONTRAST to the optimal value for the video input level automatically Adjust the H POSITION V POSITION H SIZE and FINE to the optimal value automatical
14. for the dual monitor stereo mode If you are using a professional application make sure that OpenGL settings are enabled Refer to the owner s manual for the graphics card Be certain the video cable to the bottom display is the left image appears to be inverted channel and the cable to the top display is the right channel Also make sure that the image sent to the top monitor is mirror flipped either by software or the mirror flip PCI card Only one display is showing an image Be certain that your graphics card is configured for two monitors Use clone mode horizontal span also called stretch mode or dual monitor mode configuration Be sure that all video cables are securely connected 22 SD2620W Warranty The SD2620W standard warranty includes a 1 year return to depot replacement warranty service Return the defective part of the system for a replacement with a comparable product All components have a 30 day inspection warranty period All system components have a 1 year warranty Two business day delivery Expedited Delivery Service available Extended Warranty Terms are available Go to www planar com for the complete details of the warranty including support procedure returning a nonfunctioning unit extended warranty limitations and exclusion of damages Product Registration To register your product go to www planar com support cust asp User s Guide 23 CRT Recycling If your ne
15. hat the upper monitor is seen in a mirror see discussion below Presenting the stereo pair of images requires a setup or software application that accommodates dual monitor stereo viewing No additional modification is needed for use with the StereoMirror monitor design Any software application that uses the OpenGL quad buffered stereo features is compatible with the StereoMirror Quad buffered stereo is a feature of the OpenGL 3D graphics library that allows an application to define two separate right left eye viewpoints instead of the normal single monoscopic viewpoint The two viewpoints are defined to give the correct parallax separation for the proper stereo effect Once the two viewpoints have been defined the 3D scene is rendered identical for each of the two viewpoints Many commercial 3D applications already have stereo viewing modes using the OpenGL stereo features Since the upper display of the monitor is seen in reflection a mirror flip operation must be performed on that data path In the current product this is accomplished using an auxiliary signal processing board in the data path to the upper monitor Driving a StereoMirror monitor is identical to driving a pair of projection displays used to show stereoscopic images with crossed polarizers in the two separate light paths An off the shelf dual output graphics card is employed to drive the two monitors again with no special preparation Mirror flip PCI Card
16. itors with a DVI signal For professional applications that use OpenGL quad buffered stereo the graphics card should support OpenGL stereo as well Typically the two monitors should be in clone mode for these applications with stereo enabled There are several compatible graphics card families The NVIDIA Quadro FX line is recommended for OpenGL stereo applications The NVIDIA GeForce line offers dual DVI output graphics cards that work well for PC gaming and DirectX applications Visit www planar3d com for more details on graphics cards software configuration and using side monitors with the SD2620W unit Install the mirror flip PCI card Proper ESD electrostatic discharge handling precautions should be exercised when installing the mirror flip PCI card Consult the computer manual for proper installation of graphics cards Because the viewer will see a reflection of the top monitor this image needs to be flipped on the horizontal axis A mirror flip PCI card is included with the SD2620W unit Plug this card into a free PCI slot in your computer There are no drivers to load with the card 1 Remove the blank bracket from an available PCI slot 2 Insert the mirror flip PCI card into the slot align the connector pins and press the board down until it is firmly seated Mirror flip PCI card installed 3 Secure the mounting bracket 6 SD2620W Connect the cables The SD2620W unit comes with one 6 foot DVI cable
17. ly MENU FUNCTION FUNCTION DESCRIPTION EXPANSION This function allows you to MODE choose from different display modes e Full Expands all resolution to full screen e Aspect Enlarges native resolution to either horizontal or vertical limit e Real Displays native resolution e Default setting FULL LEFT RIGHT Adjust the horizontal image Analog Input position only DOWN UP Adjust the vertical image Analog Input position only CLOCK Adjust the sync frequency of Analog Input internal pixel clock only PHASE Adjust the value for improve Analog Input display focus only User s Guide 13 MENU 14 SD2620W USER RED GAIN FUNCTION COLOR TEMPERATURE RED GREEN BLUE GAIN RED GREEN BLUE OFFSET SATURATION FUNCTION DESCRIPTION Choose different color temperature 9300K 7500K sRGB USER Default is USER USER mode adjustable Adjust the contrast and brightness of each color of the white balance Allows you to adjust the Red Green Blue color gain Allows you to adjust the Red Green Blue color offset Adjust color depth Increasing this value makes pictures more colorful decreasing makes pictures less colorful Adjustable value from 100 to 100 Factory setting 0 MENU S I DE COLOR FUNCTION DDC CI SIDE COLOR RECALL LANGUAGE OSD LEFT RIGHT OSD UP DOWN OSD TURN OFF RESOLUTION NOTIFIER FUNCTION DESCRIPTION
18. presentative at 1 866 PLANAR1 1 866 752 6271 Service is available Monday through Friday 5 A M 5 P M Pacific time 8 A M 8 P M Eastern time E mail Support Send your inquiries to planarsupport planar com PLANAR Planar Systems Inc 1195 NW Compton Drive Beaverton OR 97006 1992 Customer Service E mail planarsupport planar com Online www planar com support Voice 1 866 Planar1 1 866 752 6271 020 0641 00A
19. reas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field Indirect sunlight User s Guide iii Box Contents The SD2620W shipping box contains the following components Bottom monitor assembly with mirror support arms and mirror adjustment screws Bottom cable management cover Top monitor assembly Top cable management cover Beamsplitter assembly Two power cords 6 ft and 10 ft iv SD2620W A YF Two DVI cables 6 ft and 12 ft Product user s guide Spring clip style glasses 1 ea a Soft dry cloths 3 ea Two Analog VGA cables 6 ft and 10 ft Short DVI cables 14 in Captain style glasses 2 ea Terminator style glasses 2 ea Moistened cleaning pads 6 ea NOTE Both the Captain style and the Terminator style glasses for use with the SD2620W monitor feature the Planar logo on each side and white arm tips These two markers differentiate the glasses from those shipped with other stereo monitors User s Guide v Contents SACS INO LIC Ot lite ei eaters citen et tiet o cel iii BOX COMTE S etat i menentiGetomatedenmtsstemnteesttssuil iv Stereoscopic Viewing igssisaet tastets cn ote 1 StereoMirror Technology sessesessssesessesesoesesossesesoesesossesessesesoesesonsesesoesesosseseseese 2 GENIS Nedeni E E T Ee eee rr 4 PrOQUELUS Ei ositmtascettmtsemtamemeenumtsstmenmdstel 9 Adjusting the Monitor s Displ
20. ror in 2D mode adjustment screws f The mirror should not be forced down This can break the glass and damage the mirror frame The mirror must be pulled forward before lowering User controls and OSD menu The two monitors have a power switch on the right side of the bottom bezel and a power toggle switch on the back The LED indicator next to the Power button shows the monitor power status When the LED is green the power ison When the LED is amber the monitor is in power saving mode The monitor is off when the LED indicator is dark Controls and LED indicator User s Guide 9 The Source button allows you to select VGA or DVI input The Menu button activates the OSD on screen display main menu Use the Exit button to close the OSD menu this is also a DV mode hot key The Auto button is a hot key for auto adjusting the display A four direction 4D 1 button allows you to move up down left and right within the menu systems Press the four direction button to enter or exit menus 4D 1 key function definition This table lists the function definitions of the four direction 4D 1 button PUSH KEY DIRECTION HOT KEY Up Contrast Down Contrast Right Brightness Left Brightness Center 10 SD2620W MENU Cursor Up Cursor down Cursor right Volume Cursor left Volume Item Enter Exit Adjusting the Monitor s Display The monitor has four function control buttons by which you can sel
21. surface A soft cloth moistened with glass cleaner water and or mild detergent can also be used to clean the mirror Do not touch the half mirror surfaces with sharp or hard objects Do not use abrasive cleaners waxes or solvents for cleaning Polarized glasses Use a dry soft cloth clean room wiper or compressed air when cleaning the polarized glasses A soft cloth moistened with water and or mild detergent can also be used to clean the glasses Do not touch the surfaces of the polarized glasses with sharp or hard objects Do not use abrasive cleaners waxes or solvents for cleaning Software Compatibility OpenGL The SD2620VV unit is compatible with OpenGL stereo An appropriate graphics card is required to drive the two monitors with DVI signals For professional applications that use OpenGL stereo support the graphics card should support OpenGL stereo as well Stereo viewing of professional applications is typically done in the so called clone mode where most of the same information is duplicated on the left and right monitor except for the stereo imagery In other words the desktop windows and menus are identical but the bottom monitor shows the left eye image while the top monitor exhibits the right eye image DirectX The SD2620W unit is compatible with the DirectX application programming interface Accessories For repetitive transportation of the SD2620W unit a reusable ruggedized shipping case is available from Plan
22. w Planar monitor is replacing a CRT unit keep the following in mind e Ifthe CRT unit is in good working condition consider donating it to a school or nonprofit organization It may qualify as a charitable tax deduction e Do not throw away a CRT unit Cathode Ray Tubes contain hazardous materials and cannot be discarded with other refuse A number of recycling programs are available Do an online search of CRT Recycling for potential service providers in your area Important Recycle Instructions a LCD lamps inside this product contain mercury This product may contain other electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal laws For more information contact the Electronic Industries Alliance at www eiae org For lamp specific disposal information check www lamprecycle org 24 SD2620W For more information on StereoMirror technology go to www planar com advantages whitepapers Planar Customer Service Online Support For support available 24 7 visit our Online Technical Support page at www planar com support Online Technical Support is where you can find solutions for common problems download documentation view answers to frequently asked questions FAQs and get troubleshooting advice Visit www planar3d com for specific questions about configuring the stereo monitor Customer First Technical Support Call a customer service re
Download Pdf Manuals
Related Search