DMX-512 LED CONTROLLER
Contents
1. For Installations where long distance DMX cable connections are needed we suggest to use a DMX terminator The DMX terminator is a male XLR 3 5 pins connector with a 120 ohm resistor Between pin 2 and 3 The DMX terminator must be plugged into the last unit DMX out panel connector of the DMX line PLACE A 120 OHM RESISTOR BETWEEN PIN 2 AND 3 OF A MALE XRL CONNECTOR AND PLUG IT INTO THE DMX OUT PANEL CONNECTOR OF THE LAST UNIT CONNECTED TO THE DMX LINE PIN 3 PIN 2 The standard configuration of the Z1 is with XLR 5 pins connectors 5 Z1 LED Controller DMX ADDRESS Z1 can be used in two different modes 5 or 9 DMX default channels If you want to use the Z1 in 5 channels mode select the 5 CH mode from the MODE menu and set the following addresses on the mixer Projector 1 A001 Projector 2 A006 If you want to select the next projector just add 5 Projector 3 A011 Nr A projector 6 A026 If you want to use the Z1 in 9 channels mode select the 9 CH mode from the MODE menu and set the following addresses on the mixer Projector 1 A001 Projector 2 A010 If you want to select the next projector just add 9 Projector 3 A019 eae A projector 6 A046 Selelcting the DMX address 1 Press the UP DOWN key until you reach the required DMX address The numbers on the display will start to flash but the new DMX address hasn t yet been set 2 Press ENTER to confirm your selection The nu2. 260 Vac 50 60 Hz SA ANS RGB output 6 pin Female Rj12 Pin 1 RED Pin 2 RED Pin 3 GREEN EE A Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE 6 pin Female RJ12 RJ12 6P6C 6 pin Male RJ12 6P6C indicates 6 positions 6 cables Modular Plug 123456 LEDs cabling connection can be done with a standard UTP TIA EIA 568 A category 3 cable The maximum distance between power supply and the last LED lamp in the line should not exceed 100 meters For short distance connections less than 20 meters you can also use a standard 6 conductors telephone flat cable 4 Z1 LED Controller DMX SIGNAL CONNECTION The unit operates using a digital DMX 512 signal Connection between the controller and the unit or between units must be carried out using a two pair screened 40 5 mm cable and a CANNON XLR 5 or 3 pole connector Ensure that the conductors do not touch each other Do not connect the cable ground to the XLR chassis The plug housing must be isolated Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to the DMX IN plug of the second one In this way all the projectors are cascade connected CONTROLLER STANDARD DMX 512 3 1 GND DATA DATA 1 2 3 FR P S If the display showing the DMX address flashes then one of the following errors has occurred DMX signal not present DMX reception problem
3. D T S MR16 RGB LED lamp MR16 full color LED lamp D30 RGB LED projector D30 full color LED projector D150 full color LED projector 3 channels output DMX 512 Power interface able to drive RGB LED units Max 25W x channel 3 x 350mA electronically dimmable led control outputs Main Input voltage range is 90V 260V 50 60 HZ It is possible to use this item through every DMX 512 mixer or by using the DTS InfraRed control MAIN ELECTRICAL CHARACTERISTICS Input Voltage Range Vin 90 260 Vac Frequency 50 60 HZ Power Consumption Range 6 60 W Power Factor Pf 0 95 electronic PFC controller Efficiency 90 typical IP protection grade IP 20 Output Power Output Range 1 5 25W per channel Output Current 350 mA 100 per channel 500mA 100 per channel in BOOST Mode Output Voltage Vout 48V Max Load output 15 x MR16 RGB LED lamp or 15 x D30 RGB LED projector or 5 x MR16 full color LED lamp or 5 x D30 full color LED projector or 1 x D150 full color LED projector Min Load output 1x MR16 RGB LED lamp Control Input Control Signal DMX 512 Dimming System Constant Current PWM Address Range DMX 512 channels addressable by display APPLICATIONS Cinemas Restaurants and pubs Discoteques Architectural Interior and Exterior 3 Z1 LED Controller INPUT OUTPUT CONNECTIONS DMX IN OUT connectors STANDARD DMX 512 CONTROLLER 1 GND 2 DATA 2 8 DATA Display Mains 90
4. by user CUPr RGB values selectable hy user Rainbow rAln Rainbow colours effect Speed time selectable by user CU01 CU16 Color Macros as on DMX channel 8 Macro ENTER Es DOWN IS ENTER a oe a ENTER UP DOWN ENTER 8 Z1 LED Controller AUTOMATIC MODE Automatic demo game without DMX controller WHITE MACROS 16 macros for White color from 2000 to 7200 K DIMMER Dimmer level selectable by user as on DMX channel 2 Dimmer Dimmer level is active for all the programs and_macros SHUTTER Shutter level selectable by user as on DMX channel 1 Shutter Shutter level is active only for CU01 CU16 and Wh01 Wh16 macros ESC Esc from Automatic Mode Menu Ex Ex ENTER UP DOWN ENTER REC MODE In DMX Recorder Mode it is possihle to create and store the scenes of the ChPr hy using an external DMX controller The unit must be setted to 9 channels MODE DMX Recorder Mode For the programming of ChPr by using a DMX controller besides the 9 channels necessary to control the unit a further 3 DMX channels are needed So that in RECORDER mode via DMX the unit will need 12 channels to he correctly programmed The three new DMX channels are DMX channel 10 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 11 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration g
5. use or application of the products or circuits described herein MADE IN ITALY E The Lighting Company D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 info dts lighting it www dts lighting it
6. Code 03 LA 009 VA DMX 512 LED CONTROLLER User s manual V 1 1 a Pole o y omg A pr 2 ri A Og ls 4 f gt i KA i i s i A 3 BA i A fr ER A A Ve RE AN AP bd Je NE E M A e f Es Er J s The Lighting Company 2 Z1 LED Controller IMPORTANT SAFETY INFORMATION Fire prevention Never locate the fixture on any flammable surface Minimum distance from flammable materials 10 cm Replace any blown or damaged fuses only with those of identical value Prevention from electric shock High voltage is present inside the unit Unplug the unit prior to performing any operation which involves touching the inside of the unit This equipment must be grounded do not connect to non grounded supplies The use of a thermal magnetic circuit breaker is recommended for each Z1 Use only AC supplies 90 260V 50 60Hz The unit should never be located in position exposed to rain or in areas of extreme humidity A good air ventilation is essential for proper equipment work Safety The external surface of the unit may exeed 50 C never handle the unit until at least 5 minutes have elapsed since the unit was turned off Never install the unit in an enclosed area lacking sufficient air flow The ambient temperature should not exeed 40 C and should not be lower than 10 C DESCRIPTION Z1 DMX 512 LED controller is a unit dedicated to the following LED products by
7. Parameter COLOUR MACROS Move DMX range range Mode Option Function Value AEE EGET sa EE 04 14 NoFunction Function A AAA 3044 pp pp Maa IE CIO Matre gt 604 pp Y Maerod gt BA o Y Mares 90004 pp Marr MAA Macro 12044 pp Maero gt 135 149 pp Maero9 150 164 pp Maerol0 gt 165179 pp Yoo Maeroll gt 180 194 Macro dt 195 209 Y MaerolB gt 21028 pp Maerold gt 226 239 pp ECC 240255 pp pp Macrot 6 O DMX CHANNEL 9 Parameter FUNCTIONS Recall Create and Store the Custom white Move DMA range range Mode Option Function Value degrees 079 O Custom White Recall Enable CH 6 for Custom white Recall 80 160 Ll Custom White Create Enable CH 6 for Custom white Creation 161 255 mr Custom White Store Store the Custom White created 16 Z1 LED Controller 5 CHANNELS MODE 1 SHUTTER 2 DIMMER 3 RED 4 GREEN 5 BLUE DMX CHANNEL 1 Parameter SHUTTER DMX range Mode Option Function Value 0 J ee o Black out 109 14 1 gt Open 20 29 24 gt Black out 30 119 Strobe at variable speed from slow to fast 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 MEA Pulse close at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full Open 230 255 240 DMX CHANNEL Parameter DIMMER DMX ran
8. e speed for the colour changhing SPEE DIMMER function in AUTOMATIC MODE is active for all the programs SHUTTER function in AUTOMATIC MODE is active only for CU01 CU16 and Wh01 Wh16 macros ChPr MASTER SLAVE The first unit that will function as a Master must be set to Automatic mode AUTO the other units must be set to Slave mode SLAV selectable through the menu In this way all the Slave units will be synchronised with the master and running their own ChPr game On the master unit it is possible to vary the Speed time SPEE for the colour changhing and the Wait time UAIt between the steps Speed time and Wait time on the Master have priority on the slave units NB It is possible to run GA Pr on the other units even though these do not have GA Pr programmed You can do this by setting the units to 9 ch DMX MODE and selecting DMX address A001 Rec mode It is possible to program your own game on the Z1 that will then run it in AUTO mode ChPr Each unit can have its own programmed game In REC mode Z1 unit must be set to 9 channels mode To program the ChPr by using a DMX controller you need 3 more channels in addition to the 9 channels necessary to control the unit So that in RECORDER mode via DMX the unit will need 12 DMX channels to be correctly programmed 12 Z1 LED Controller The three new DMX channels are DMX channel 10 SCENES channel From 0 10 no function r001 From 11 255 are displayed the program
9. ersion 10 Z1 LED Controller HIDDEN MENU For technical personnel only To operate this menu Connect the unit to the main While reset is running press the MENU and ENTER keys at the same time Reset EEPROM Reset all settings ATTENTION by pressing this key you must repeat all previous calibrations UPLOAD This menu allow to upgrade the unit s software by computer DOWNLOAD This menu allow to save unit s programs into computer EXIT Exit from hidden menu 11 Z1 LED Controller AUTOMATIC OPERATION AUTO Z1 can work in automatic mode without a DMX controller First of all connect the projectors with a DMX cable picture below A maximum quantity of 32 slave units can be connected to the same Master unit MASTER SLAVE 1 SLAVE 2 SLAVE 3 SLAVE 32 E Se on pe N To activate Auto mode on the first unit use the menu to run through the different modes until AUTO appears on the display at this point press enter Now it is possible to choose between the different pre programmed games CUPr RAIn CU01 CU16 Wh01 Wh16 or ChPr which is user programmable through REC mode To confirm game activation press ENTER on the selected GAME CUPr RAIn CU01 CU16 Wh01 Wh16 The first unit that will work as a Master should be placed in Automatic mode AUTO the other units have to be placed in 9 channels DMX mode MODE 9CH and the DMX address should be set at A001 For Raln rainbow game it is possible to select th
10. ge Value DMX CHANNEL Parameter RED DMX range Value DMX CHANNEL 4 Parameter GREEN DMX range Value DMX CHANNEL Parameter BLUE DMX range Value 0255 Proportional colour 17 Z1 LED Controller Z1 LED UNITS WIRING CONNECTIONS Pin 1 D T S INFRARED REMOTE SENSOR CODE 03 LA 016 0506420 D T S T BOX CODE 03 LA 001 IZ LNO LNANI IMPORTANT The maximum number of MR16 RGB 3W LED lamps connectable to the Z1 Power supply is 15 pcs The maximum number of D150 full colour Led projector connectable to the Z1 Power supply is 1 pcs IZ1NO MANI Never plug the cable coming from the Power supply into OUT 1 or OUT 2 of the T BOX when other MR16 lamps are connected because a wrong connection can seriously damage the lamps Never plug in a new MR16 lamp when the power supply is turned on E Weno 4andn 15w Z 18 Z1 LED Controller Note 19 Z1 LED Controller Note 20 The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the
11. iven by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REG it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 12 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed 9 Z1 LED Controller SLAVE MODE Slave mode for ChPr program All slave units will be synchronised with master unit running their own Chpr program INFRARED MODE Infrared remote control By activating Ir MODE it will be possible to navigate trought the unit functions by using the D T S infrared remote control D T S Code 0514L008 ENTER a NOTE External infrared remote sensor needed D T S Code 03 LA 016 DEFAULT To restore default settings ENTER LIFE TIME This menu show the total UNIT life tine and the RGB life time ENTER TEST MODE RGB colours test with rainbow SOFTWARE Software v
12. mable scenes max 16 scenes from M001 to M0016 DMX channel 11 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 12 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed INFRARED REMOTE CONTROL soe Button By activating Ir MODE on Z1 Menu it will be possible to navigate trought the unit functions by using the D T S infrared remote control D T S Code 0514L008 Please note that external infrared remote sensor is also needed D T S Code 03 LA 016 Infrared remote control functions 1 9 ON OFF and MUTE buttons Buttons In Automatic mode let you stop the games running AR Master and slaves will go in Stand by mode 1 9 buttons VOL PROG I
13. mbers on the display will stop flashing and the projector is now controlled by the new DMX address TIPS if you keep pushed the UP or DOWN keys the channels are calculated more quickly and you get a faster selection 6 Z1 LED Controller DISPLAY FUNGTIONS DFP Digital Function Panel MENU ENTER DOWN DISPLAY FUNGTIONS The Z1 display panel shows all the available functions Using these functions it is possible to change some of the parameters and add some functions Changing the D T S setting can vary the functions of the unit so that it does not respond to the DMX 512 signal used to control it Carefully follow the instructions below before carrying out any variations or selections NOTE the symbol p gt shows which key has to be pushed to obtain the desired function Software version 1 04 IF IS isis PGS I ss Floor IS MENU UP DOWN ENTER UP DOWN ENTER UP DOWN position ENTER REVERSE DISPLAY SR Reverses display s reading depending on p ae the mounting position position Ser On the ground or suspended as DISPLAY STAND BY To turn off the display after 5 seconds Display Or leave it always on always ON enter ES IS s gt 5 CHANNELS IS pmx mode default 9 CH DMX MODE 13 To select DMX mode 5 9 default GAS 9 CHANNELS ENTER channels Boost mode activated ESS nit BOOST active the LED current is setted to 500mA 30 more gain ENTER Default Disable BOOST DRIVING This men
14. n Automatic mode let you select the colour macros 1 9 PE Bone 1 Button rn In Automatic mode let you select the colour macros 10 16 Buttons VOL NAVIGATION In Automatic mode let you select the desired value for DIMMER Buttons PROG MENU In Automatic mode let you scroll between the selectable games OK PURON RED GREEN YELLOW BLUE buttons Peon Direct acces to Automatic mode for Red Green Blue Yellow colour macros Red CU01 Green CU07 Yellow CU04 Blue CU13 Navigation buttons Same as UP DOWN on unit display OK button Same as ENTER on unit display MENU button 13 Z1 LED Controller DMX PROTOGOL 9 CHANNELS MODE Default SHUTTER DIMMER RED GREEN BLUE WHITE Pre programmed whites at different color temperatures CTC COLOURS MACRO FUNCTIONS VONAURWNKA Parameter SHUTTER DMX range Mode Option Function Value a 5 poo Black out 1049 14 1 gt Open 2029 24 1 gt Black out 30 119 Strobe at variable speed from slow to fast 3400ms 20ms 120 149 Pulse open at variable speed from slow to fast 43s 100ms 150 179 NM Pulse close at variable speed from slow to fast 43s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 255 240 Open DMX CHANNEL Parameter DIMMER ee Move DAMA renge range Mode Option Function Value Mg degrees 0 255 Proportional dimmer _ AE Move DAMA range range Mode Option Fu
15. nction Value AA grees 0 255 Po Proportionalcolour 14 Z1 LED Controller RGT ES Parameter GREEN WAN Move SIRS amg range Mode Option Function Value Seer grees 0 255 Proportional colour DMX CHANNEL Parameter BLUE nese Move DMX range range Mode Option Function Value EN epres grees 0 255 Po Proportionalcolour DMX CHANNEL 6 Parameter WHITE Pre programmed White at diff color temperature DMX range Mode Option Function Value 055 No Function 56 105 80 Full Red Green Blue at Full 106 155 130 White DTS IF CHANNEL 9 FUNCTIONS CUSTOM WHITE RECALL Dmx range value 0 79 156 205 180 Custom White Recall White CTC Channel 7 CTC enabled 20022 de 43 color temp Correction Macros 2000 K 7200 K IF CHANNEL 9 FUNCTIONS CUSTOM WHITE CREATE Dmx range value 80 160 156 205 Custom White Create RGB levels selectable by DMX 206 255 White CTC Channel 7 CTC enabled 43 color temp Correction Macros 2000 K 7200 K _DMX CHANNEL 7 Parameter CTC Color temperature correction Move LAOS Kle range Mode Option Function Value degrees IF CHANNEL 6 White WHITE CTC Dmx range value 206 255 0 255 43 color temp Correction Macros 0 2000 K 128 5500 K 255 7200 K IF CHANNEL 6 White NO FUNCTION Dmx range value 0 43 0 255 Smooth RGB linear Hue correction 15 Z1 LED Controller DMX DMX CHANNEL 8
16. u allow to increase the Pen ee LED s current from 350mA to 500 mA Boost mode deactivated MENU UP DOWN ENTER UP DOWN LED RGB Min Max Smooth and Compression level values settings UP DOWN RGB MINIMUM VALUES This menu allow to select the minimum levels for Red Green and blue RGB MAXIMUM VALUES This menu allow to select the maximum levels for Red Green and blue UP DOWN Ep These settings have priority on Master Dimmer DMX channel 2 UP DOWN SMOOTH VALUE This menu allow to select the value of the delay in millisecons for RGB and Dimmer channels reaction to DMX or Program variation Off 25 ms delay Fast response 20 250 ms delay Slow response COMPRESSION This menu allow to select between Linear courrent output or Quadratic courrent output for LEDs Default Linear UP DOWN m Z m A m T U o Z Z Z1 LED Controller 7 E Ta ee ENTER UP DOWN ENTER Default 255 ENTER SS inet fl ENTER UP DOWN ENTER Default 255 ES ENTER SS er bl ENTER UP DOWN ENTER Default 255 QP ENTER IS ES Range Off 20 RSP ENTER UP DOWN Default 2 ENTER Off 25 ms Istant responce to DMX variation 20 250 ms Smooth response to DMX variation Linear Linear courrent output ENTER Quadratic Linear light output ENTER AUTOMATIC MODE Automatic demo game without DMX controller ChPr Chase with 16 steps previously created in REC MODE Speed and Wait time selectable
Download Pdf Manuals
Related Search