Ontech GSM 9020
Contents
1. means alarm function is turned on GPS alarm Last valid GPS 57d38 440N Latitude degrees and minutes N or S 10d28 000E Longitude degrees and minutes E or W Speed 0 knots Speed Dir XXX Direction XXX is the degree 24 Time 10 48 53 Time at latest reading UCT time like GMT Date 2009 02 28 Date at latest reading UCT time GPS Tracking Ondico AB will start up a service that makes it possible to track how the Ontech 9020 is moving on a Google Map More information will be available on our web site www ondico se Important Be aware of the power consumption of the GPS receiver It is approximately 40 50 mA and makes the battery time shorter Power supply Connecting power supply and charging Ontech 9020 can be power supplied in different ways 1 With the enclosed Power Adapter 13 8V 2 With a 12 V accumulator Both the adapter and the accumulator is connected to terminal A and the 12 and OV connectors See page 10 Be careful to get the polarity right otherwise the unit can be damaged If both the accumulator and the power adapter are connected the accumulator will be charged as long as the power adapter is connected to the main power The accumulator acts like a backup battery in case of power failure WARNING Manganese batteries or other not rechargeable batteries may not be used Decrease power consumption In order to decrease power consu2. By connecting a GPS receiver Ontech GSM 9020 will upon request send an SMS with position direction speed and time The unit can also be set to alarm if the unit is moving outside a predefined distance from the original position GPS Fence GPS receivers On the web site www ondico se we will publish information about recommended GPS receivers that has been tested to work together with Ontech GSM 9020 To be able to connect a GPS receiver you must use an GPS adapter Ontech GPS adapter OND 9020 003 This is optional and is not included in the Ontech GSM 9020 package Connecting an GPS receiver See page 10 for how to connect the Ontech GPS adapter OND 9020 003 The adapter is connected to contact D Request GPS data from the unit You request GPS data from Ontech GSM 9020 by sending an SMS with the following content ABCD 8 1 where ABCD is your personal PINCODE The unit will reply with an SMS similar to this example Ontech 9020 Asterisk means alarm function is turned on Last valid GPS 57d38 440N Latitude degrees and minutes N or S 10d28 000E Longitude degrees and minutes E or W Speed 0 knots Speed Dir XXX Direction XXX is the degree Time 10 48 53 Time at latest reading UCT time like GMT Date 2009 02 28 Date at latest reading UCT time If there is no GPS receiver connected or if there is no GPS signal the following SMS will be sent No GPS Data GPS alarm GPS f
3. In the name field of the contact write DELAY6 and in the field for the telephone number write 45 Activation of relay when alarming Alarmrelay This function activates the relay when the unit is alarming This function is useful if you for example have an alarm detector that alarms when water level is too high the relay is activated and turns on a pump e The function is activated by adding a contact on the SIM card and name it ALARMRELAY In the telephone number field write 1 see page 7 e hefunction is deactivated by removing the contact from the SIM card Turn off on the alarm function Each time you start up Ontech GSM 9020 the alarm function is turned on 60 seconds after the green lamp has stopped flashing This delay is because you shall have time enough to move away from the alarm detectors compare with an ordinary alarm If you do not want the alarm function to be active you can deactivate it If you do not have any alarm detector connected you do not have to think about this Turn off on the alarm function with a telephone 1 Call up the unit Be sure you use tone mode on the telephone 2 Theunit answers with a beep 3 Press your PINCODE and then Example 12344 If the PINCODE is correct the unit replies with a beep If it is not correct the call is disconnected Call again and try 4 Turn off the alarm function by pressing buttons 17 7 0 The unit replies with a beep Hang up the receiver
4. Internal battery emty 9020 shuts down Is sent only if an internal backup battery has to be connected Is sent when voltage is dropping below 3 7 Volt The unit is shutting down SMS about GPS If there is a GPS receiver connected you can request GPS data by sending an SMS to the unit with the following content ABCD 8 1 where ABCD is your personal PINCODE You will immediately receive an SMS as below Ontech 9020 Asterisk means alarm function is turned on 30 Last valid GPS 57d38 440N Latitude degrees and minutes N or S 10d28 000E Longitude degrees and minutes E or W Speed 0 knots Speed Dir XXX Direction XXX is the degree Time 10 48 53 Time at latest reading UCT time like GMT Date 2009 02 28 Date at latest reading UCT time If the GPS Fence alarm is activated and the unit has moved outside the fence all telephone numbers on the alarm list will receive a GPS SMS SMS showing the SIM card settings If you want to control the settings of the SIM card you can request an SMS that shows most of the SIM card settings Send an SMS to the unit with the following content ABCD 8 2 where ABCD is your personal PINCODE You will immediately receive an SMS as below Content Exlanation Ontech 9020 Asterisk means alarm function is turned on Alarmrelay Alarmrelay function ON or OFF Tempwatch indicate
5. Deactivate the relay send an SMS to the unit with the following text ABCD 0 1 where ABCD is your personal PINCODE Activate the relay with timer function The relay can be set to be activated during a preset number of hours 1 99 Send an SMS with the following text ABCD 1 1 T where ABCD is your personal PINCODE T the number of hours you want the relay to be active Instead of the symbol you can use all letters uppercase or lowercase on button 7 p q rors Instead of the symbol you can use all letters uppercase or lowercase on button 9 w X y OF Z Tip If you not are sure about the settings of the unit you can request a SIM card setting SMS see page 29 13 The position of the relay after a power failure If there is a power failure and the relay is activated it will change to deactivated position When the power returns it will remember the position it had before the power failure If this is not desired please set DIP switch 8 to position ON Alarm Ontech GSM 9020 can alarm in many different ways All alarms are sent as SMS to the telephone numbers on the alarm list see page 7 The unit can be programmed so the relay activates when there is an alarm see pagel7 Wired alarm Two alarm inputs where alarm detectors can be connected Can be set as Normally Open NO or Normally Closed NC Wireless alarm In the year 2009 Ondico AB will start to sell different wireless alarm units which co
6. GSM 9020 Troubble shooting Symptom Reason Both the red and green lamp is flashing on Ontech GSM 9020 The unit cannot read the SIM card e Checkthat the PINCODE is deactivated See page 6 e Check that the position of the SIM card in the unit is correct e Check the SIM card in a mobile phone in order to check the SIM card The green lamp is flashing on Ontech GSM 9020 The unit has no contact with extra units or wireless alarms No connection with the GSM network e Check if the area is covered by using the SIM card in a mobile phone e Checkthat the antenna is correctly mounted e Test with another SIM card Different radio channels e Check so all units in a system has the same radio channel See page 28 Ontech GSM 9020 has no contact with an individual extra unit The unit do not react on SMS Out of radio range e Check by moving the extra unit closer to the master unit e Check that the extra unit has a unique ID See page 28 e Place one more extra unit in the middle of the distance between the slave unit that lost contact and the master unit Wrong mobile number e Check that the mobile number is correct Wrong PINCODE e Checkthat your PINCODE is correct The easiest way to do this is to call up the unit from an ordinary telephone and enter the PINCODE and then st If the PINCODE is correct the unit will reply with a beep If not the unit will hang up Technical specifica
7. The cabinet is in accordance with IP65 The unit is powered by 12 VDC A 12 V accumulator or the enclosed power adapter can be used Remotely controlled by telephone calls or SMS Alerts and sends GPS position data via SMS Relay230V 10A Potential free Can be connected Normally Open or Normally Closed Has a timer function Can be programmed to remember position after a power failure Two alarm inputs for corded alarm detectors Can be set to NO or NC Can be programmed to activate relay when alarms Wireless alarm detectors will be available during 2009 nternal temperature sensor reports temperature External temperature sensor with high accuracy is optional Alerts if the temperature falls below or rise above alarm temperature Thermostat function temperature regulates the relay GPS receiver buy optional can be connected Reports position direction and speed in SMS GPSFence function alerts if unit is moving outside programmed distance to fence Is set in meters in multiples of 50 meters finternal backup battery buy optional is connected the unit will alert if the main power is disconnected Can be set to be delay in up to 40 minutes Can control extra relay units Ontech 9010 via short range radio lt 5 Content in package e Ontech GSM 9020 e Antenna e Users Manuals e Power adapter 138 V Get started In order to use the unit you must have a SIM card for a GSM mobile telep
8. by requesting an SMS with SIM card settings See page 31 Do this every time you have changed the SIM card settings 1 Create a send list for alarms see page 14 1 Create a new contact Name it SMSO note that 0 is zero and not the letter O 2 Enterthe mobile phone number for the receiver of the SMS Save 3 The following contacts in the send list are named SMS1 SMS2 etc and the mobile numbers are entered All numbers from SMSO to SMS9 can be used in total 10 different numbers 2 Setdelay for activation of alarm detector DELAY see page 17 1 Itis possible to set a delayed activation for an alarm detector This is for giving you time to deactivate the alarm before the unit is sending an alarm 2 Create a new contact Name it DELAYX X is the ID of the alarm detector you want to delay values of 1 8 are permitted i Write the numbers of seconds you want to delay in the telephone number field Example You want alarm detector with ID no 6 to b activated with a delay of 45 seconds In the name field of the contact write DELAY6 and in the field for the telephone number write 45 3 Activate the temperature guard TEMP see page 20 1 Create a new contact and name it DEGREE i Write the alarm temperature in the telephone number field If the alarm temperature is below zero degrees Celsius add zero 0 before the temperature For example minus 7 degrees C is written as 07 2 Create a new contact an
9. rises one degree C above the set temperature it will deactivate the relay turning off the radiator First connect the radiator to the relay See page 10 This shall be done by a professional electrician Activate the thermostat from a telephone 1 Call up the unit Be sure you use tone mode on the telephone 2 Theunit answers with a beep 3 Press your PINCODE and then Example 12344 If the PINCODE is correct the unit replies with a beep If it is not correct the call is disconnected Call again and try 4 Dial 2 D where D the desired temperature The unit confirms with a short beep Hang up If the unit replies with two beeps try again Deactivate the thermostat from a telephone 1 Call up the unit Be sure you use tone mode on the telephone 2 Theunit answers with a beep 3 Press your PINCODE and then Example 12344 If the PINCODE is correct the unit replies with a beep If it is not correct the call is disconnected Call again and try 4 Dial 2 The unit confirms with a short beep Hang up If the unit replies with two beeps try again Activate the thermostat with SMS 1 Activate the thermostat function by sending an SMS with the following content ABCD 2 D where ABCD is your personal PINCODE D is the desired temperature Deactivate the thermostat with SMS 1 Deactivate the thermostat function by sending an SMS with the following content ABCD 2 where ABCD is your personal PINCODE GPS positioning
10. t p Lu C us n aS ay 25 Connecting power supply and charging tte 25 Decrease power consumption ettet tttttttesttttctnssttt 25 POWAD ACEO RY Lem t omnee etate eo t MR Ra d tad 25 Internal BACKUP Battery t ctt iR ttn 26 Power failure alarrm ettam aae epp N 26 Delayed power failure alarm ttt REREN 26 Turn off turn on the unit if an internal backup battery is connected 27 Short range radio extra relayS sssssssssssssssssessessesesesesesessesseseseseseseseseseseseees 28 RETF ENC e 29 SMS fromthe OPE sescenti ie usa oted bc td tees 29 AlarmiSMSV Status SMS c sciet ble aeu tbe nes iecit bebe us 29 SMS about power Supply oos eo ene a e EA M ee M eem 30 SMSa BOUT OPS a M act a cutleh A E al cadet 30 SMS shOWINGHME SIMcatd settiltes acted t a NA 31 COMMA Nd Serea etd Push button BER PRE DIR SWI tEn a e Eee Rue a MEO LE EIU UE 34 po 35 Troubble shooting tentent ae aa ee ae vae ea ee eoe eS eee eene iere En 37 Technical specifications eeclesie eese eene entente tn enenetn tn enene tatnen ente tn en sis 38 Declaration of conformity eere eee eese eee ee eee te teens ntn tnenene tatnen enete tn enenenet 39 4 Overview Ontech GSM 9020 is a combined remote relay and an alarm caller and is communicating over the GSM network
11. If the unit replies with two beeps try again 5 Turnon the alarm function by pressing buttons 7 1 The unit replies with a beep Hang up the receiver If the unit replies with two beeps try again Turn off on the alarm function with an SMS 1 To turn off the alarm function send an SMS with the following message ABCD 7 0 where ABCD is your PINCODE 2 Turnon the alarm function again by sending an SMS with the following message ABCD 7 1 where ABCD is your PINCODE Turn off on the alarm function with the remote control In the year 2009 Ondico AB will start to sell a remote control This is used to turn off on the alarm More information will be published on our web site www ondico se Tip If you want to know if the alarm is turned on or off you can check this by requesting a status SMS from the unit see page 29 When the alarm is turned on there is an asterisk before the name Ontech9020 It looks like this Ontech9020 When the unit is alarming Alarm list When an alarm is activated an SMS will be sent to all mobile telephone numbers on the alarm list How to create this list see page 7 Up to ten different persons can be alerted Alarm SMS Alarm SMS and Status SMS looks identical and shall be interpreted as follows Example Explanation Ontech9020 Asterisk means alarm function is turned on Alarm lab 3b Indicates all alarms that have been activated since the last acknowledge The nu
12. Ontech GSM 9020 User Manual ENGLISH Welcome Thank you for choosing Ontech GSM 9020 We hope that the product will satisfy your needs and that you will find this manual easy to handle and that it guides you in an appropriate way If you want to learn more please visit our web site at www ondico se where you can find more information Questions can be directed to support ondico se SMS text will be shown with gray background and bold text for example 1234 1 0 Also the buttons to be pressed when using a telephone in tone mode not pulse is shown in this way Text in italic indicates a menu in your mobile phone for example Contacts Quotation mark shall never be written in the contacts it is used in this manual only in order to separate the commands from other text This version of the manual is valid for all units with software version 005 or later To check the version of your unit please refer to SMS showing the SIM card settings on page 31 Ondico AB is not responsible for damages that may occur due to incorrect use or if the product does not work as desired 22s Content OVeIVIe Wes enano dese sene eU A Mu eee 5 Content in package neret eite t etes eb eb eet eie eet e eb eebe eb ebeb e eb eeb e eb eebe eb epeb epe 6 ETE EA e E a POEPEN EE AA tet testet tisse etes tette tet etes stetit ettet etes sted teg stet etes stet etes stet eden Necessary programming of the SIM card Optio
13. S means that inputs 1a 1b and 3b has been activated since the last acknowledge and that input 1b is still activated Units 1 3 4 Indicates the units communicating with the Ontech GSM 9020 Unit number 1 is always Ontech GSM 9020 The other numbers refers to the extra relays Ontech 9010 connected An asterisk after the number indicates that the relay is turned on If Ontech GSM 9020 loose contact with one of the extra relays unit its ID number will not be shown in the SMS Temp 24 24 2 Gives the temperature in degrees C The first number refers to 29 will be written instead If there is an asterisk for the internal temperature sensor the second number refers to external temperature sensor if connected If not connected this indicates that the unit has sent a temperature trigged by example 24 2 before the number this sensor Tstat 25 Indicates the set temperature for the thermostat function If thermostat not is activated the message is Tstat OFF SMS about power supply The SMS sent to alert about the power supp y are as follows Content in SMS Meaning Charge battery s sent when voltage is dropping below 12 Volt Battery empty s sent when voltage is dropping below 11 Volt No main power s sent only if an internal backup battery has to be connected s sent when voltage is dropping below 8 Volt Relay alarm function and GPS are disconnected
14. and or the power adapter to the The green lamp starts to flash for about 45 seconds This indicates that the unit is searching and connecting to an GSM network The green lamp stops flashing and lights constantly The unit is now connected to the GSM network and is ready to use If the green lamp not stops flashing and also the red lamp starts flashing this means i No SIM card installed ii The pin code of the SIM card is not deactivated see page 6 Check the SIM card settings It is recommended to control the SIM card setting after installation See page 31 Do as follows 11 1 Send an SMS to the unit with a request of the SIM card setting Write ABCD 8 2 where ABCD is the PINCODE you have programmed to the SIM card 2 Theunit replies with an SMS with the settings Testing the unit When you have installed the unit it is recommended to test the function Call the unit or send SMS to control the relay Test the alarm inputs if used Ask for status SMS to check temperature Functions Remote relay With this function you can call the unit or send an SMS and activate or deactivate the 230V 10A relay NB If you shall use main power contact a professional electrician Normally Open Connect the cables to connector 2 and 3 on terminal B When activated the relay will connect the two connectors and when deactivated the connectors are disconnected Normally Closed Connect the cables to connector 1 and 3 on ter
15. are set to NO mode The unit sends an ALARM A if connectors A and 12 are connected and ALARM B if connectors B and 12 are connected If DIP switch 1 is set to ON the mode is switched to NC The unit sends ALARM A if connectors A and 12 are disconnected and ALARM B if connectors B and 12 are disconnected 15 Suggestion for connection of alarm detectors in Normally Open NO mode OV A B 412 Lil e Detector A Detector B Suggestion for connection of alarm detectors in Normally Closed NC mode OV A B 412 S IT e Detector A Detector B Wireless alarm detectors In the 2009 Ondico AB will market wireless alarm detectors These can be easily connected to work together with Ontech GSM 9020 Up to 7 different detectors can be connected On Ondico website www ondico se we will inform more about this 16 Delayed activation of alarm detector Sometimes it can be desired to delay the activation of an alarm detector This is for example when you want to go inside the house and deactivate the alarm before it sends alarm messages Program the SIM card see page 7 as follows 1 Create a new contact Name it DELAYX Xis the ID of the alarm detector you want to delay values of 1 8 are permitted i Write the numbers of seconds you want to delay in the telephone number field Example You want alarm detector with ID no 6 to be activated with a delay of 45 seconds
16. d an SM S with the following content Main power restored If the backup battery is discharged an SMS will be sent to all telephone numbers on the alarm list with the following content Internal battery empty 9020 shuts down The unit shuts down Delayed power failure alarm The unit can be programmed to delay a power failure alarm This can be useful if the unit is connected in an area with short main power failures and you do not want alarm SMS if the power returns after a short while Do as follows 1 Create a new contract and name it POWERFAIL i Inthe telephone number field write the number of minutes delay you want 1 40 is allowed i If the digit 0 zero is set the function will be deactivated Turn off turn on the unit if an internal backup battery is connected To turn off the unit without disconnecting the power push the button and hold for 5 seconds To turn it on again push the button and hold for 5 seconds Short range radio extra relays Ontech GSM 9020 has a 2 4 GHz short range radio This is used to communicate with extra relays Ontech Relay 9010 and or wireless alarm detectors available year 2009 If the short range radio not is in use it is recommended to turn it off in order to lower the power consumption Do this by setting DIP switch number 6 to position ON see page 25 In a system with one Ontech GSM 9020 and one or more extra relays or wireless alarm detectors all has individual ID numb
17. d name it TEMP i Inthe telephone number field write 1 if you want an alarm if the temperature drops below the alarm temperature given 7 in DEGREE or write 2 if you want the alarm when the temperature rises above the alarm temperature 4 Setactive temperature sensor EXTTEMP see page 20 1 Ifyou have an external temp sensor optional and you want it to control the temperature alarm and thermostat you have to activate it Create a new contact and name it EXTTEMP i In the telephone number field write 1 5 Active the function relay activates at alarms ALARMRELAY see page 17 1 Create a new contact and name it ALARMRELAY i In the telephone number field write 1 6 Activate delay for Power failure alarm POWERFAIL see page 26 1 Ifan internal backup battery optional has been connected the unit alarms when the ordinary power is disconnected It is possible to set a delay for this alarm 2 Create a new contract and name it POWERFAIL i Inthe telephone number field write the number of minutes delay you want 1 40 is allowed i If the digit 0 zero is set the function will be deactivated 7 Activation of the GPSFENCE see page 24 1 Ifa GPS receiver optional has been connected you can set it to send an alarm if the unit has been moved from its original position You can set at which distance from the original position you want the unit to send an alarm 2 Create a new contact and na
18. d with a beep If there is a fault the unit replies with two beeps Using other letters for and Instead of the symbol you can use all letters uppercase or lowercase on button 7 p q rors Instead of the symbol you can use all letters uppercase or lowercase on button 9 w X y OF Z Checking SIM card settings If you not are sure about the settings of the SIM card you can request an SIM card setting SMS see page 29 Status SMS If you not are sure about the settings of the unit you can ask it for a status SMS See page 29 To long distance between Ontech GSM 9020 and Extra relays or wireless alarm detectors A built in function in all Extra relays and wireless alarm detectors is a radio repeater This means that each extra unit increases the working range with about 30 meters If one extra unit is out of range another extra unit can be connected somewhere between the 35 extra unit that is far away and Ontech GSM 9020 The extra unit will link the other two units together Check if the extra unit Ontech GSM 9020 has contact with the master unit One push of the button on the extra unit Ontech Relay 9010 switches the relay but is also sending information about this to Ontech GSM 9020 This unit acknowledges back that it has received the information During this process the red lamp on the extra unit will flash The process shall not take more than 3 seconds if more the extraunit probably lost contact with Ontech
19. ence A GPS fence is a function which means that an alarm will be sent if the unit has moved away more then a certain distance from its original position The distance is set in multiples of 50 meters for example 50 m 100 m 150 m etc The original position is the position the unit has one minute after start up If the unit has been powered but the alarm function has been turned off see page 17 original position is the position the unit has one minute after the alarm has been turned on again Setting To activate the function 1 Create a new contact on the SIM card and name it GPSFENCE a Inthe telephone number field write the number for the distance from original position to GPS fence Write the multiple to multiply with 50 meters Example If you wish the unit to send an alarm when it has moved 300 meters from its original position write in the telephone number field 6 as 6 50 300 If you want an alarm at 900 meters write 18 as 18 50 900 When you start up the unit after programming the SIM car verify the GPS function by requesting an SMS with GPS data see page 23 The GPS fence alarm is turned off when you turn off all others alarm see page 17 You can also turn it off by deleting the GPSFENCE contact on the SIM card When there is an GPS fence alarm If the unit has moved outside the GPS fence an alarm SMS will be sent to all phone numbers on the alarm list The SMS is similar to this Ontech 9020 Asterisk
20. ers Up to 8 different unique numbers can be used 1 8 Ontech GSM has always number 1 With the DIP switches 2 5 the radio channel for the short range radio is set In Ontech GSM 9020 as well as in extra relay Ontech Relay 9010 and the wireless alarm detectors these DIP switches are delivered in position OFF If another radio channel shall be used be sure to set the DIP switches 2 5 exactly the same in all units in the system Reference SMS from the unit Alarm SMS Status SMS The alarm SMS and the status SMS are identical The alarm SMS is sent to all the telephone numbers on the alarm list You can request a status SMS by sending and SMS to the unit with the following content ABCD 8 where ABCD is your personal PINCODE You will immediately receive an SMS as below You cannot request status from an ordinary telephone only with SMS Status SMS is only sent to the telephone that requested the status Example Explanation Ontech9020 Asterisk means alarm function is turned on Alarm lab 3b Indicates all alarms that have been activated since the last acknowledge The number indicates the units ID number Ontech 9020 is always no 1 and the others refer to the extra units ore wireless alarm detectors connected Note that these inputs not can send an alarm again before the alarm has been acknowledged Inputs 1b Indicates the alarm input that still is activated In this example the SM
21. hone and access to a mobile phone Cash card can be used The installation is made in three simple steps 1 Programming the SIM card 2 Physical installation 3 Testofthe unit and its functions Necessary programming of the SIM card Insert the SIM card in a GSM mobile phone Deactivate the PINCODE function See the user manual of the mobile phone Delete all old contacts from the SIM card if there are any qe Nec Choose Contacts in the mobile phones menu a Create a new entry Name it PINCODE b Inthe field for telephone number enter your personal four digit number This number is the PINCODE you must enter each time you contact your Ontech GSM 9020 5 Goto Optional programming of the SIM card if you want special functions or 6 Turn off the mobile phone and remove the SIM card Go to to Physical installation see page 10 Make sure that you save all information are on the SIM card and not only in the memory of the GSM telephone It can be necessary to open the contacts and copy to the SIM card from the memory of the telephone See the manual of the telephone Avoid to copy more contacts than necessary to the SIM card No quotation marks or slashes or similar shall be written just the text 6 Optional programming of the SIM card In order to use some of the function you want it can be necessary to program more contacts on the SIM card See below NB To be sure programming is made in a correct way you can check
22. mber indicates the units ID number Ontech 9020 is always no 1 and the others refer to the extra units ore wireless alarm detectors connected 18 Note that these inputs not can send an alarm again before the alarm has been acknowledged Inputs 1b Indicates the alarm input that still is activated In this example the SMS means that inputs 1a 1b and 3b has been activated since the last acknowledge and that input 1b is still activated Units 15 3 4 Indicates the units communicating with the Ontech GSM 9020 Unit number 1 is always Ontech GSM 9020 The other numbers refers to the extra relays Ontech 9010 connected An asterisk after the number indicates that the relay is turned on If Ontech GSM 9020 loose contact with one of the extra relays unit its ID number will not be shown in the SMS Temp 24 24 2 Gives the temperature in degrees C The first number refers to the internal temperature sensor the second number refers to external temperature sensor if connected If not connected will be written instead If there is an asterisk for example 24 2 before the number this indicates that the unit has sent a temperature trigged by this sensor Tstat 25 Indicates the set temperature for the thermostat function If thermostat not is activated the message is Tstat OFF Acknowledge an alarm When an alarm detector has trigged the alarm it has to be acknowledged before
23. me it GPSFENCE i In the telephone number field write alarm distance in multiples of 50 meters Example If you want an alarm when the unit has moved 300 meters away from the original position write the digit 6 6 50 300 If you want to set 900 meters write 18 18 50 900 8 Position of the contacts on the circuit board zaji DIPSWITCH NT A lolka az jag SIM 7 X E CARD HGE B 2 i3 D Fig 1 Upper side of the circuit board BATTERY B Fig 2 Back side of the circuit board NB The backup battery is optional and not standard Installation of internal backup battery If you want to use an internal backup battery see page 26 you should install this before the physical installation The backup battery is optional and is not included in the standard package If you do not install a backup battery go to section Physical installation see page 10 1 Open the unit by unscrew the two screws on the left and right sides 2 Turn the unit so you face the under side 9 Ed Ove cd v ull carefully the hood until you can see connector E on the circuit board Do ot pull longer as there is a risk for the flex cable to the membrane switch to isconnect o E Remove the protection paper on the tape on the battery Place the battery according to the figure above Connect the contact of the battery to connector E Push the hood back to its original position and replace the screws o
24. minal B When activated the relay will disconnect the connectors and when deactivated the connectors are connected Control the relay manually You can activate and deactivate the relay by pushing on the button on the front When the relay is activated the red lamp is lit Control the relay with a telephone 1 Callthe unit Be sure you use tone mode on the telephone 2 Theunit answers with a beep 3 Press your PINCODE and then Exemple 12344 12 If the PINCODE is correct the unit replies with a beep If it is not correct the call is disconnected Call again and try Activate the relay by pressing the buttons as follows 1 1 The unit confirms with a beep If there are two beeps try again Deactivate the relay by pressing the buttons as follows 0 1 The unit confirms with a beep If there are two beeps try again Activate the relay with timer function The relay can be set to be activated during a preset number of hours 1 99 Press the buttons as follows 1 1 T T the number of hours you want the relay to be active The unit confirms with a beep If there are two beeps try again After you have made one operation you can directly continue with another operation without calling up again When you have completed all operations then hang up Control the relay with SMS ly Tip Activate the relay send an SMS to the unit with the following text ABCD 1 1 where ABCD is your personal PINCODE
25. mmunicate with Ontech 9020 Up to 7 different alarm detectors can be connected The wireless alarm detectors planned are A Motion detector B Magnet switch Alarm box and C Emergency Alarm button Also a remote control to turn on off the alarm will be offered Temperature alarm The temperature alarm is trigged if the temperature rises above or drops below the preset alarm temperature See page 20 GPS alarm If a GPS receiver is connected the unit can be set to alarm if it is moved a preset number of meters from its original position See page 24 Battery alarm The unit alarms if the battery needs to be charged or if the battery is empty Power failure alarm If an internal backup battery is connected the unit will alarm if the main power failures A delay of this alarm can be set to up to 40 minutes See page 26 14 Wired alarm Connect an alarm detector When an alarm detector is activated it will either close or open an electric circuit It can be a magnetic switch detector a level detector a motion detector or any other kind of sensor To connect an alarm detector the unit must be opened The alarm detectors are connected to Terminal A see page 10 The connector on the terminal has the following markings OV Ground A Alarm input A B Alarm input B 12 Voltage 12 V Switch from Normally Open to Normally Closed mode Locate the DIP switch see Fig 1 Factory default for switch 1 is OFF This mean the alarm inputs
26. more than one degree from set alarm temperature fthe alarm is set to alarm when it drops below temperature X it will not send another alarm before it has risen above X 1 degrees fthe alarm is set to alarm when it rises above temperature X it will not send another alarm before it has dropped below X 1 degrees 1 Create a new contact and name it DEGREE i Write the alarm temperature in the telephone number field If the alarm temperature is below zero degrees Celsius add zero 0 before the temperature For example minus 7 degrees C is written as 07 2 Create a new contact and name it TEMP i Inthe telephone number field write 1 if you want an alarm if the temperature drops below the alarm temperature given in DEGREE or write 2 if you want the alarm when the temperature rises above the alarm temperature The unit will send an SMS alarm to all the telephone numbers on the alarm list if the temperature drops below rises above the set alarm temperature The function is deactivated by removing TEMP contact from the SIM card Thermostat function If an electrical radiator is connected to the relay the unit can be used as a remote thermostat controller 21 By programming the desired temperature the unit will scan the temperature and activate the relay and thus turn on the radiator if the temperature drops one degree C below the set temperature The surrounding air will be warmer and when the temperature
27. mption you can turn off the short range radio if it not is used The power consumption will then decrease with about 10 mA The short range radio is not used if there is no extra relays Ontech Relay 9010 or wireless alarm detectors Low battery Ontech GSM 9020 will alarm at battery as follows 25 Ifthe voltage between connector 12 and OV drops below 12 Volt an SMS will be sent to all telephone numbers on the alarm list with the following content Charge battery Ifthe voltage between connector 12 and OV drops below 11 Volt an SMS will be sent to all telephone numbers on the alarm list with the following content Battery empty None of the low battery alarms needs to be acknowledged Important If there has been a low battery alarm the unit has to be restarted or the voltage must rise above 12 5 V before it can send a new low battery alarm Internal backup battery As an option an internal backup battery Ontech Backup Battery 9020_001 can be purchased This is mounted inside the cabinet according to the instruction on page 9 Power failure alarm If an internal backup battery is connected and the voltage drops below 8 Volt an SMS will be sent to all the telephone numbers on the alarm list with the following content No main power The alarm function the GPS and the relay will be disconnected The temperature measurements will not be affected When the main power returns the unit will sen
28. nal programming Ofte SIM card betae ette e tu EDAR Position of the contacts on the circuit board ttes 9 Installation of internal backup battery ttes 9 Physicalinstallatiolc tette OD E ML Em 0 ChecktheSIM catrd settiligs coe eter ett NR RR 1 Testing tAE U DES stet REN eet del f eoa 2 AAT aTa tK cL 12 R mmote relayi suite dpa bo EpL E C SURE Y MU Or UMS d 2 Controlthe relay manually ha e D nu e us 2 Control the relay with a telephone ttn 12 Control therelay With SM Sisaria e RR n e Rd 13 The position of the relay after a power failure ts 14 Aa T 4 Wired EAE TUAn m S 5 Wireless alarrm detectors cus o e ee UE E m pe catu 16 Delayed activation of alarm detector Peles Activation of relay when alarming Alarmrelay t 17 Turnieft onthiealammft nctlo sq nce teta petit etica capt dedu 17 Wlienithieuni amp is alatmlig sse de tenta dle obe et hme dts 8 Acknowledge analaFfrs sons tt e bebe aan e Laces o e tal 19 Jerpefatule cssere sos oce tees eer Meee teAp teet begann pa LADDER 20 lermperat re Seriso s u eeepc eerte pede ties cett ad 20 Temperature alaiaren si o IH Um o con ow uu ctrca eae 20 Thermostat function 42 IuoXereritTejslnio Mere 23 clurssuce e R 23 COMMEGUIMG am GRS ec e ast cett RR OR sete RU eb dte tum 23 Request GPS data Tromsthie Urt es e tet le d e eden ds 23 GPS alam GPS ences cce ette bt b ons 24 GPS Trackin G aeo cl edu dei t EN R 25 PoWersupply csset daichii e Bade ime a cette ast
29. ormally Open Relay use connector 2 and 3 If you want Normally Closed Relay use connector 1 and 3 Maximum load is 230V 10A 10 is NB If you shall connect main power contact a professional electrician Alarm page 14 Terminal A Alarm A is connected to connector 12 and A and alarm B is connected to connector 4 12 and B External temperature sensor page 20 Contact C Connect the connector Adapter for GPS receiver page 23 Contact D Connect the connector When all desired cables have been connected turn the screw cap clockwise in order to create a tight seal You can use plastic tape around the bundle of cables to make it thicker and that way create a tighter seal Set the DIP switches in desired positions Factory default is OFF setting for all switches a Switch 1 Set to ON if you want the wired alarm inputs to be NC See page 34 Switches 2 5 are used to set the radio channel for short range radio communication with Extra relays or wireless alarm detectors See page 28 Switch 6 Set to ON if you do not use the short range radio and wants to turn it off in order to decrease power consumption See page 25 Switch 8 Set to ON if you want the relay not to remember its position in case of a power failure See page 14 Push the hood back to its original position and replace the screws and also the screw on top of the hood mains a Connect the power cable to the accumulator
30. ot deactivated See page 6 Both are flashing The DIP switch Th e unit has 8 DIP switches see page 9 The functions of th DIP switch no Function 1 OFF Alarm A and B are set to mode Normally Open ON Alarm A and B are set to mode Normally Closed ny A w N These four switches are used to set the radio channel If extra relays Ontech Relay 9010 or wireless alarms are used in a system all units must have the same radio channel settings O FF Short range radio turned on Short range radio turned off Z O ot in use Al F The relay will remember position in case of power failure ON OFF The relay will not emember position in case of power failure switches are set to OFF as factory default e switches are as follows Position OFF on the DIP switches is downwards compared to the text on the switch Tip Cash card If you are using SIM cash card be aware that many network operators demands you are sending at least one SMS or make one call every year Some also demands you refill at least once a year Check with your operator Multiple commands in the same SMS or call It is possible to execute multiple commands in the same SMS or call The sign separates all the command lines If you for example want to acknowledge an alarm but also want to activate the relay you press ABCD 9 1 1 All individual commands will be replie
31. r 9020 002 If you wish to use the external temperature sensor for controlling the thermostat and trigging the temperature alarm you have to program the SIM card for this purpose see page 7 Create a new contact and name it EXTTEMP and in the telephone number field write 1 NB The external temperature sensor is not delivered together with Ontech GSM 9020 It is optional Temperature alarm Default setting If the temperature alarm is turned on the unit will send an alarm if the temperature drops below 5 degrees C The alarm does not have to be acknowledged but the unit will not send another alarm before the temperature has reached at least 6 degrees C The temperature alarm is not activated by default Activate the temperature alarm as follows 1 Create a new contact and name it TEMP In the telephone number field write 1 if you want an alarm if the temperature drops below 5 degrees C or write 2 if you want the alarm when the temperature rises above 5 degrees C The unit will send an SMS alarm to all the telephone numbers on the alarm list if the temperature drops below rises above 5 degrees C The function is deactivated by removing TEMP contact from the SIM card Setting alternative trigging temperature for the temperature alarm You can set an alternative temperature of your choice for the temperature alarm The alarm does not have to be acknowledged The unit cannot send another temperature alarm before it has changed
32. r continue with the physical installation Physical installation 1 Place the unit on the place of your desire and attach it by using screws in the two holes The antenna shall point down If you want to install an internal backup battery this shall be done prior to this physical installation see above Open the unit by unscrew the two screws on the left and right sides Pull carefully the hood approximately 5 cm or until you can see the two green screw terminals Do not pull longer as there is a risk for the flex cable to the membrane switch to disconnect Install the SIM card see picture a The upper part of the SIM card holder is moved to left until you hear a Click b Fold up the upper part of the SIM card holder c Placethe SIM card in the upper part The cut corner of the SIM card shall be positioned in the upper right corner when the upper part of the card holder is folded back d Fold back the upper part e Lock the upper part by moving it to the right until you hear a click Open the screw cap by screwing it to the left Pull the cables through the screw cap Connect the cables a Power Terminal A 12VDC Either the power adapter or an 12V accumulator or both Plus is connected to connector 12 Minus is connected to the connector OV Important Do not connect to power at this stage It can damage the equipment On power adapter positive cord is white b Relay page 12 Terminal B If you want N
33. s if the unit alarms when the temperature drops below set temperature gt indicates if the unit alarms when the temperature rises above set temperature Temp sens Indicates which temperature sensor that controls alarms and thermostat INT internal sensor EXT den external sensor GPSfence OFF The GPS fence function is turned off The number indicates the distance from the original position to the GPS fence The number shall be multiplied with 50 in order to get the distance in meter Ver Shows software version Useful when contacting support Commands This description is valid both for telephone button and SMS text Command Explanation ABCD All telephone calls and SMS starts with your personal PINCODE of 4 digits When writing this symbol you are sending a command to the unit Thus the symbol ends a command If you have misspelled you can use this symbol to restart the command This symbol is used as a separator inside a command 1 N Used to activate a relay N the ID of the unit O N Used to deactivate a relay N the ID of the unit 1 N T Used to activate a relay with timer function N the ID of the unit And T the number of hours you want the relay to be active 2 Used to turn off the thermostat function 2 D Used to turn on the thermostat function 0 29 degrees C 7 1 Used to turn on the alarm function 7 0 Used to turn off all alarms
34. the unit can send another alarm Temperature alarms GPS fence alarm and power fail alarm do not have to be acknowledged Acknowledge an alarm manually Press the button on the front of the unit at least once Note that also all alarm from the extra relays Ontech 9010 will be acknowledged Acknowledge an alarm with a telephone 1 Call up the unit Be sure you use tone mode on the telephone 2 Theunit answers with a beep 3 Press your PINCODE and then Example 12344 19 If the PINCODE is correct the unit replies with a beep If it is not correct the call is disconnected Call again and try 4 Acknowledge the alarm by pressing the buttons 9 The unit replies with a beep Hang up the receiver If the unit replies with two beeps try again Also alarms from extra relays Ontech 9010 will be acknowledged Acknowledge an alarm with SMS 1 Send an SMS to the unit with the following message ABCD 9 ABCD is your PINCODE Also alarms from extra relays Ontech 9010 will be acknowledged Temperature Temperature sensors Ontech GSM 9020 will by default use the internal temperature sensor for controlling and alarming The accuracy is 3 degrees C The internal temperature sensor is also affected by the relay If the relay is activated it will indicate 1 2 degrees higher than normal due to heat produced by the relay If you wish higher accuracy 1 we recommend you to purchase the external temperature sensor Ontech Temp Senso
35. tions GSM GSM subscription Relay Serial interface Short range radio Alarm inputs Inernal backup battery External power supply Power consumtion Temperature range Certified GSM 900 1800 All kinds also cash card Potential free 230V 10A Special for GPS adapter Frequency 2 4 GHz Power output 1 mW Activated either by NO or NC mode aximalt 50 V 5 mA Oprtional Li polymer 4 2 V 1100 mAh 9 24 V AC DC Nominal lt 0 5 W Max 4 W 20 C to 40 C Compliance EMC LVD and R amp TTE directive Declaration of conformity Ondico AB Datav gen 14A 436 32 Askim Sweden hereby declares that the product Ontech GSM 9020 is in conformity with the provisions of the Radio amp Teleterminal directive R amp TTE 1999 5 EG WWW ondico se SEE ce LLZOCL NJ AI OvOSL
36. valid for all alarms except low battery alarms 8 Status SMS request 8 1 Request for GPS data 8 2 Request for SIM card settings 9 Used to acknowledge alarms e All SMS must begin with your personal PINCODE e tis possible to send multiple commands in the same SMS or telephone call The symbol separates the commands e When operating with a telephone call all commands are confirmed with a beep Two beeps indicate a failure Try again e Instead of the symbol you can use all letters uppercase or lowercase on button 7 p q rors e Instead of the symbol you can use all letters uppercase or lowercase on button 9 w x y or zZ Push button One push at the button activates or deactivates the relay One push is also used to manually acknowledge an alarm Push and hold for 5 seconds to turn on turn off the unit if there is an backup battery connected One push turns of thermostat function if activated 32 The lamps On the front of the cabinet there are two lamps one red and one green GREEN LAMP Flashing Flashes when establishing connection with GSM network during start up The unit is turned on and has contact with GSM network On no flashing RED LAMP On no flashing The relay is activated Off The relay is deactivated Flashing One alarm has been activated and is not acknowledged RED AND GREEN LAMP SIM card is missing or Pincode on SIM card is n
Download Pdf Manuals
Related Search