ELP-362D Emergency Locator Beacon
Contents
1. WATER SWITC N FLAT WASHE CAP SCREW on 1 4 MINIMUM SELF LOCKING NUT THREAD ENGAGEMENT Figure 3 2 Securing the Mounting Bracket RETAINING PLATE ELP 362D a ma l H gt e EN MOUNTING HDWARE 3 PLCS MOUNTING BRACKET Figure 3 3 Installing the Beacon into the Mounting Bracket User s Manual February 2015 ELP 362D Emergency Locator Beacon 10 Pre Deployment Tests A pre deployment test on each beacon should be performed before and after mounting using the RJE INTERNATIONAL INC ATS 260 Acoustic Test Set The test set can be used to check both the beacon s battery condition and operation Also an alternative method using a digital voltmeter can be used to check the beacon s battery condition ATS 260 Acoustic Test Set To use the ATS 260 Acoustic Test Set to verify the battery condition and test the operations of the beacon use the following procedure 1 Attach the cable clip directly to the beacon housing as shown in Figure 3 4 It is not necessary to remove the beacon from the mount to conduct the test Although the cable clip can touch the beacon label it is important that at least part of the clip touch the bare aluminum surface of the beacon Apply the test set probe to the water activation switch as shown2. February 2015 o0 ELP 362D Emergency Locator Beacon Installation Procedures Carefully unpack the beacon and inspect it for shipping damage If any damage is evident it should be reported to the freight carrier and to RJE International Inc The mounting bracket kit includes an aluminum mounting bracket an aluminum end plate three drilled for lockwire socket head cap screws and three lock washers NOTE Before installing the mounting bracket be sure that it will be possible to install and remove the beacon once the bracket is installed To mount the beacon perform the following steps 1 Refer to the mounting bracket hole pattern shown in Figure 3 1 and drill four 0 191 in 0 48 cm diameter holes 2 Secure the mounting bracket with four 10 32 stainless steel screws and associated hardware not supplied as shown in Figure 3 2 3 Slide the beacon into the bracket as shown in Figure 3 3 Rotate the beacon until the battery date is visible and secure it in place with the end plate and the three drilled socket head cap screws 4 Lockwire the drilled screws and clean the water activation switch refer to section 4 Beacon Cleaning 4X 9 19 DRILL THRU Figure 3 1 Mounting Bracket Hole Pattern User s Manual February 2015 ELP 362D Emergency Locator Beacon 9 be 2 o 7 32 4 1 8 _ MOUNTING BRACKET ASSEMBLY e
3. Installation Considerations To minimize the probability of physical damage or inadvertent activation the following precautions should be considered when mounting the beacon The beacon should normally be mounted in the aft mid section of the aircraft depending on the environmental conditions and should be mounted to a sturdy structure without weakening the structure itself The beacon should be mounted in an area guarded against heavy equipment tearing loose and striking the beacon and should be mounted in a way that provides convenient access during regular inspections and tests The beacon should be mounted in a clean dry area to decrease the probability of inadvertent activation Also if possible the beacon should be mounted with the water switch facing down to minimize the possibility of moisture gathering on the end cap The beacon should be mounted in an area that is protected from the outside elements This will assist in the long term prevention of corrosion The beacon should be mounted in an area where sound absorbent materials are not present Avoid affixing labels to the beacon or any other material that would affect the acoustic beam The shelf life of the battery will be decreased when exposure to higher than normal temperatures The maximum temperature where the beacon is mounted should not exceed 71 C 160 F Nonconformance to the mounting instructions or intended use may void the warranty User s Manual
4. 160G as required by TSO C121 A summary of the testing qualifications is presented in the table below ELP 362D TSO Testing Qualification Summary RTCA D 160 Description of Test Section No Conducted 50 000 ft 4 6 2 4 6 3 12 0 13 0 14 0 15 0 19 0 Testing Conditions Decompression Overpressure en Equipment tested to RTCA DO 160D Figure 8 2 Curve J Fixed Wing and Figure 8 4 Curve Y Rotary Wing 452 48a ica eer cn ar oe roca Z Induced Signal HE Other Tests Performance environmental and Crash Survivability Testing performed as required by AS 8045 Salt Spray Magnetic Effect User s Manual February 2015 ELP 362D Emergency Locator Beacon y 3 Installation and Checkout This section encompasses the installation considerations and procedures for mounting the beacon using the mounting bracket kit and a pre deployment test that can be conducted using a RJE INTERNATIONAL INC ATS 260 Acoustic Test set NOTE The conditions and tests required for the TSO approval of this article are minimum performance standards It is the responsibility of those installing this article either on or within a type or class of aircraft to determine that the aircraft installation conditions are within the TSO standards TSO articles must have separate approval for installation in an aircraft The article may be installed only if performed under 14 CFR part 43 or the applicable airworthiness requirements
5. Beacon 5 2 Specifications This section provides information on the operating and environmental specifications on the ELP 362D Emergency Locator Beacon General Specifications Operating Frequency Operating Depth Pulse Length Pulse Repetition Rate Battery Operating Life Battery Storage Life in Beacon Acoustic Output Acoustic Output After 30 Days with standard lithium battery Acoustic Output After 90 Days with optional lithium battery Activation Beam Pattern Case Size Case Material Weight Storage Temperature Operating Temperature User s Manual 37 5 kHz 1 kHz 0 to 20 000 feet 6 096 meters 2 9 ms gt 0 9 pulses per second Lithium P N C362 04270 2 Lithium content 0 7grams Discontinued effective March 1 2015 Lithium P N B362 D90 01 Lithium content 0 9 grams per cell 2 30 days lithium battery C362 04270 2 Discontinued effective March 1 2015 2 90 days lithium battery B362 D90 01 7 years 2 160 5 dB re 1 uPa 1 meter 2157 0 dB re 1 Pa 1 meter 2157 0 dB re 1 Pa 1 meter Fresh or salt water immersion 80 sphere 1 30 in 3 30 cm diameter 3 92 in 9 95 cm long 7075 T6 aluminum 6 7 ounces 190 grams maximum 55 C 67 F to 71 C 160 F 2 C 28 F to 38 C 100 F February 2015 ELP 362D Emergency Locator Beacon 6 TSO Testing Qualification Summary The beacon is designed to meet the performance specifications of RTCA DO
6. DIES SET FORTH HEREIN INCLUDING ANY LIABILITY FOR PRODUCTS NOT BEING AVAILABLE FOR USE OR FOR LOST OR CORRUPTED DATA LOSS OF BUSINESS LOSS OF PROFITS LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT COST OF CAPITAL COST OF SUBSTITUTE OR REPLACEMENT PRODUCT FACILITIES OR SERVICES DOWN TIME CHARGES FOR PURCHASER S TIME AND EFFORT THE CLAIMS OF THIRD PARTIES INJURY TO PROPERTY OR ANY OTHER DIRECT INDIRECT SPECIAL RELIANCE INCIDENTAL OR CONSEQUENTIAL DAMAGES REGARDLESS OF THE NATURE OF THE CLAIM AND WHETHER OR NOT FORESEEABLE AND WHETHER OR NOT BASED ON BREACH OF WARRANTY CONTRACT OR TORT INCLUDING NEGLIGENCE OR STRICT LIABILITY EVEN IF RJE International Inc HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR FOR ANY CLAIM BY ANY THIRD PARTY EXCEPT AS EXPRESSLY PROVIDED HEREIN THIS LIMITATION OF LIABILITY APPLIES BOTH TO PRODUCTS AND SERVICES AND SUPPORT PROVIDED PURCHASER UNDER THIS AGREEMENT NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY RJE International Inc ITS AGENTS OR EMPLOYEES SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THE LIMITED WARRANTY PROVIDED ABOVE ANY AND ALL LIABILITY OF RJE International Inc IS EXPRESSLY LIMITED TO THE PRICE PURCHASER HAS PAID FOR THE PRODUCTS PURCHASER S SOLE REMEDY AGAINST RJE International Inc INANY DISPUTE UNDER THIS AGREEMENT SHALL BE TO SEEK RECOVERY OF THE AMOUNTS PURCHASER PAID PURSUANT TO THE LIMITED WARRANTY PROVIDED ABOVE UPON THE PAYMENT OF WHICH RJE I
7. ELP 362D Emergency Locator Beacon Teledyne Benthos Inc Product Acquired And Manufactured by RJE International Inc User s Manual Revision M February 2015 P N 001815 RJE INTERNATIONAL INC RJE INTERNATIONAL ING 15375 Barranca Parkway Suite I 112 Irvine Ca 92618 www RJEINT com Tel 949 727 9399 Fax 949 727 0070 e mail aviationsales rjeint com ELP 362D Emergency Locator Beacon Preface This manual describes the installation and operation of the ELP 362D P N 001722 30 day 008400 90 day Emergency Locator Beacon a water activated acoustic beacon designed for use on aircraft flight recorders This manual is divided into the following six sections Description Specifications Installation and Checkout Beacon Maintenance Return Procedures Warranty MdANRON Proprietary Information The information description and illustrations in this manual are the property of RJE INTERNATIONAL ING Materials may not be reproduced or disseminated without the prior written consent of RJE INTERNATIONAL ING Changes RJE INTERNATIONAL ING reserves the right to make changes to meet new specifications at any time without incurring any obligation to modify previously installed units This manual is provided for informational and reference purposes only and is subject to change without notice Notes and Warnings Where applicable special notes and warnings are presented as follows NOTE A re
8. P B Invert the housing to remove the old battery from the unit Dispose of the expended cell in accordance PRESSURE with local regulations ASE p MMM YY LL WARNING Never attempt to recharge the battery MONTH OF RJE INTERNATIONAL Serious personal injury could result BATTERY l LOT CODE MANUFACTURE PROVIDED STEPC Inspect the interior of the ELP 362D housing for pent evidence of leaking or corrosion and inspect all threads for any signs of damage BATTERY WARNING Always keep both the housing and end cap threads free of dirt lint etc STEP D Install the new battery part number 362 99000 1 ca FADE Note that the battery label is marked with an arrow END UP Insert the battery so the arrow points towards the top water turn on end of the unit STEP E Remove the O Ring from its groove in the end cap Clean O Ring groove of any dirt lint debris etc Liberally apply the O Ring lubricant to the new O Ring and place the lubricated O Ring in the end cap groove Note Use only use lubricant provide with battery kit DO NOT SUBSTITUTE ANY OTHER LUBRICANT STEP F Re fasten the end cap to the housing Use the RJE International torque adapter to seat the end cap snugly Torque end cap to 2 to 2 5 foot pounds 2 7 to 3 4 newton meters STEPG Affix the 90 DAY BATTERY MMM YY LL label included with the kit to beacon below existing label Do not apply more than three labels on unit Contact RJE for instructions if more than th
9. cally depending on the local environment Periodic Beacon Test When the beacon is installed on a flight data or voice recorder the recommended maintenance interval is the same as that of the recorder or 24 months whichever is shortest Follow the Pre Deployment Tests referenced in Section 3 of this User s Manual Beacon Maintenance Precautions The following precautions should be exercised when handling or storing the beacon The beacon should not be exposed to temperatures in excess of 71 C 160 F as the battery life can be reduced by storage in a high temperature environment Any situation that could possibly crush or penetrate the case of the beacon should be avoided User s Manual February 2015 ELP 362D Emergency Locator Beacon 14 Battery Maintenance Replace the battery by the date stamped on the beacon label where the three letters represent the month and the four numbers represent the year Example MAR2011 is March of 2011 Other date codes prior to this manual revision include the following 1 Three letters represent the month and two numbers represent the year Example MAR 11 is March of 2011 2 Two numbers to the left of a represent the month and two numbers to the right of the represent the year Example 03 11 is March of 2011 ANN Hazardous chemicals are used in the beacon battery Dispose of the battery in accordance with local regulations Use the battery replacem
10. cssesssunveantvscassessusttenancs 3 Figure 1 4 Locating the Aircraft After Water Activation scccccssssscsssssssccssssssscesssessseeesseees 4 Figure 3 1 Mounting Bracket Hole Pattern osonnnnvovnsnnnnvennnnnnnvnnnennnnnennennnnnennsnnnnvensevnnnnesnennnnee 8 Figure 3 2 Securing the Mounting Bracket eooornnnvovvennnnvnnnennnnvnnnennnnnnnnennnnnenssnnnnnennennnnnensennnnee 9 Figure 3 3 Installing the Beacon into the Mounting Bracket ccccccssssscsssssssccssssssscessssees 9 Figure 3 4 Connecting the ATS 260 Acoustic Test Set ccccssssccssssssccsssssseccssssssecesssssseeeeees Il Figure 4 1 Standard Battery Kit Replacement Instructions cccccsssccsssssssscessssssccsssssseceeess 16 User s Manual February 2015 ELP 362D Emergency Locator Beacon 1 1 Description The ELP 362D Emergency Locator Beacon is a durable water activated underwater location aid The beacon transmits an acoustic signal at 37 5 kHz once every second for 30 days after activation with the standard lithium battery or 90 days with an optional lithium battery NOTE Effective March 1 2015 the 30 day battery will no longer be available due to new federal regulations requiring 90 day operation for Emergency Locator Beacons After March 1 2015 only the B362 D90 01 90 day battery kit will be manufactured and approved for use on existing ELP 362D Beacons P N 001722 or 008400 RJE INTERNATIONAL INC also offers bo
11. ent procedure provided with the lithium battery replacement kit P N B362 D90 01 standard lithium battery A copy of the standard lithium battery replacement instructions is found in Figure 4 1 Battery replacement should be performed by authorized personnel only Tooling Requirements Torque Wrench Commercially Available goe 1 2 Socket Commercially Available Sa B362 09111 Torque Adapter RJE International Inc ATS 260 Test Set RJE International Inc ATS 260 User s Manual February 2015 ELP 362D Emergency Locator Beacon 15 Torque Requirements Bottom End Cap 25 to 30 inch pounds Parts List tem Part Number Quantity Part Number Quantity ELP 362D 001722 1 008400 ea Battery Replacement Kit B362 D90 01 ENN B362 D90 01 99000 i Er 99000 I Beacon Disposal If it is necessary to dispose of the beacon perform the Alternative Battery Check referenced in Section 3 of this User s Manual first If the battery voltage is 6 0 volts or more remove the battery and dispose of the battery and beacon in accordance with local regulations If the battery voltage is less than 6 0 volts DO NOT remove the battery access end cap and dispose of the beacon in accordance with local regulations Awanninas Failure to observe these precautions could result in the release of hazardous chemicals Beacon Storage When long term storage is required the beacon should be stored in a cool dry environment in it
12. es 10 ATS 260 Acoustic Test Set Service ssicheeistieehiciieiaciesinth te ide ecinee iscetbiedines 11 Alternative Battery Check sara aivaisremddeddddsrradbrda bias besrasssvesel 12 Beacon Maintenance 00oo ic cccccccsceseneeeseeceseeeeeceseecseeeeaeceneeseaeeeeaeeeneeeeaeees 13 Beacon Cleaning is issecsedscasssesiasdsreiteatstasatenaraitensabdiassscauteasateseeenuseltensetdascataaatonn 13 Periodic Beacon Test iiii cicsccunahaudnnakiuuds dun bad eanouadatawaind 13 Beacon Maintenance Precautions 0000 0 cc ccceeeceneeeeeeeeneeeeaeenseee 13 Battery Maintenance mmmmssnrssrrrsnrrrrrvrrrrnnrrrrnrrrrnnnrrrnnnnrrennrersnnrersnnnrrsnnnernnn 14 Tooling Requirements asin hence eRe meee netted 14 Torque RCQUITCINONIS c ae tessa laste heads desk aadnk 15 P artS Eistsisatatsnasiearosdhklristgetanmetvsdbusetstndmetasdhianidtdig 15 Beacon Disposals c3cac3 Ganong eae Re 15 Beacon Storage LuussusqaduatedvaegsakkeadasdedesgeakaetGaaddiltr 15 Return Procedures iis iit etree hairs ae eae ee Aa 16 Warranty sissies heeded ek ee ee le 18 User s Manual February 2015 ELP 362D Emergency Locator Beacon iii List of Figures Figure 1 1 ELP 362D and Mounting Bracket scccccsssscsssssssssccssssssccssssssccesssssscccsssssseeesseees 2 Figure 1 2 ELP 362D Installed in Mounting Bracket soroovornnnvvvnennnnvevnennnnvennsnnnnvensennnnvenssvnnnne 3 Figure 1 3 ELP 362D Dinmtensions scscsscvscasensninsesedescsssnteecsdestessvsessacdes sdei
13. in Figure 3 4 Hold down the button labeled PUSH TO TEST on the test set handle Check the beacon battery condition by observing the green and red indicators on the test set If the green indicator is lit the battery is good If the red indicator is lit the battery should be replaced See Section 3 Alternate Battery Check Check the beacon operating condition by listening for an audible tone from the test set and or observing the amber indicator If there is an audible tone and or the amber indicator is flashing the beacon is operating properly If there is no audible tone and the amber indicator is not flashing the beacon is not operating properly NOTE If the beacon does not operate properly return it Teledyne Benthos Inc for service See Section 5 Return Procedures for instructions on how to return the beacon ELP 362D Emergency Locator Beacon 11 PUSH TO TEST ATS 260 ACOUSTIC TEST SET ELP 362D EMERGENCY LOCATING BEACON PN 001722 OR 008400 aren CABLE CLIP Figure 3 4 Connecting the ATS 260 Acoustic Test Set ATS 260 Acoustic Test Set Service The ATS 260 Acoustic Test Set is factory calibrated at the date of manufacture and requires re calibration every 3 years Return test set to RJE International Inc for re calibration See Section 5 Return Procedures for instructions on how to return the test set Use
14. minder to check that certain criteria are met before proceeding further in a step or sequence F VARNING A reminder that dangerous consequences could result if certain recommended procedures are not followed User s Manual February 2015 ELP 362D Emergency Locator Beacon ii Table of Contents 1 D stripti n en eoin as ica nen ess estaba leabrca ats un ne s i in iis 1 External Construction 20 0 ceseeesneceseeceseeceaeeeeaeeeeeeeaeeesaeeeeeeeaeees 3 Internal Construction ooo ccc ceeeceneeeeeeeeeeceaceeeaeeeeneceaeeceaeeesaeseneeeeaeees 4 Theory Of Operation ooo ccc cceseeesneeeseseeessseeeesseeeesseesessseeensaeeeneaees 4 Locating the Beacon ooo ccccesneceseeseeeeseecsaeeseaeeesaeeeeeseaeessaeseeeeeaeees 4 Specifications oeren eninin ei A A Mis wks 4 General Specifications o oo cece cccesssceceesssseeecesssseeeeesssseeeeessaeees 5 TSO Testing Qualification Summary 0 00000 0 0 cece eceeseeenteeentnees 6 Installation and Checkout 2200000 ccececeneeeseeceneeeeeeeeaeeeteeeeeeeeaeeeeeeeas 7 Installation Considerations 2 000 cece ceneeceneeeeneeeeeeeaeeeseeeeeeeeaeees 7 Installation Procedures asnsrnrnrnnnnonrnnnnrnennnnenrnnnnrnrnnnnennnnenrnennnnenrnsensnssnseenn 8 Pre Deployment Tests rrmrsrrnrrrrronrrrrnrrrnrrnrnrrnenrnennnnenrnnenrnennnnennnsenenennnsensner 10 ALS 200 ACOUSTIC TESTS Ele siiscessasssashcasdeias ss Sbietbovedas gan asiead soudaves io Biv tbav dae ash cab eabia vas
15. nternational Inc ITS AGENTS AND EMPLOYEES AND AFFILIATES WILL BE RELEASED FROM AND DISCHARGED OF ALL FURTHER OBLIGATIONS AND LIABILITY TO PURCHASER THE LIMITED WARRANTY OF RJE International Inc GIVES PURCHASER SPECIFIC LEGAL RIGHTS AND PURCHASER MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER st User s Manual February 2015
16. ons User s Manual February 2015 ELP 362D Emergency Locator Beacon 4 Internal Construction The major internal components of the beacon include a printed circuit board assembly a urethane encapsulated transducer assembly and a battery The battery is contained in its own separate user accessible compartment Theory of Operation The printed circuit board assembly generates all the necessary logic functions to produce a pulse with the desired characteristics The pulse is then transformed from a CMOS level square wave to a much larger 37 5 kHz sinusoidal pulse by a transformer The output of the transformer drives the urethane encapsulated transducer which propagates through the housing in the form of a tuned 37 5 kHz acoustic signal Locating the Beacon When the beacon is immersed in water it will begin to radiate an acoustic signal which can be received and transformed into an audible signal by either the RJE International Inc PRS 275 DPR 275 or DTI 300 Acoustic Pinger Receivers The PRS 275 pinger receiver can be used as a shipboard portable receiver to determine the general vicinity of the aircraft flight recorder After the area is known a diver can be deployed with the DPR 275 which will give the exact location of the aircraft Other equivalent pinger receivers may also be used Figure 1 4 Locating the Aircraft After Water Activation User s Manual February 2015 ELP 362D Emergency Locator
17. r s Manual February 2015 ELP 362D Emergency Locator Beacon 12 Alternative Battery Check In addition to using the test set to check the beacon s battery condition a high impedance minimum input impedance of 10 Megohms digital voltmeter can be used to measure the battery voltage Use the following procedure to measure the battery voltage 1 Place the negative meter lead on the water activation switch 2 Place the positive meter lead on the bare aluminum surface of the beacon housing Do not place the meter lead on the label 3 Read the voltmeter If the voltmeter reading is 6 0 volts or more the beacon has sufficient operating power If the voltmeter reading is less that 6 0 volts DO NOT remove the battery access end cap See Section 5 Return Procedures for instructions on how to return the beacon 7 VARNING Failure to observe these precautions could result in the release of hazardous chemicals User s Manual February 2015 ELP 362D Emergency Locator Beacon 13 4 Beacon Maintenance This section covers the cleaning recommended testing interval disposal storage procedures and battery replacement for the ELP 362D Emergency Locator Beacon P N 001722 or 008400 Beacon Cleaning The end cap with the water switch should remain free and clear of dirt grease and dust The end cap should be cleaned with a mild detergent and dried thoroughly with a clean cloth This process should be repeated periodi
18. ree labels are present AN WARNING Do not cross thread or apply excessive force to the end cap PLEASE CONTACT RJE INTERNATIONAL FOR ANY QUESTIONS OR RETURNS RJE International Inc Tel 949 727 9399 Fax 949 727 0070 e mail aviationsales rjeint com RETURNS Please have return reason quantity and serial number of the ELP 362D ready DO NOT SHIP the ELP 362D without receiving a Return Material Authorization PIN 362 19001 4 Rev A 2 27 15 Figure 4 1 Standard Battery Kit Replacement Instructions User s Manual February 2015 ELP 362D Emergency Locator Beacon 17 B Return Procedures If you need to return an ELP 362D Emergency Locator Beacon for warranty service contact RJE INTERNATIONAL INC for a Return Material Authorization RMA number and shipping instructions RJE INTERNATIONAL INC Tel 949 727 9399 Fax 949 727 0070 e mail aviationsales rjeint com You will need to provide the following information to receive a Return Material Authorization RMA Reason for return Number of beacons to be returned Serial number of each unit Shipping method if applicable NOTE Do not ship a beacon without a Return Material Authorization User s Manual February 2015 ELP 362D Emergency Locator Beacon 18 6 Warranty LIMITED WARRANTY RJE International Inc warrants that the products sold hereunder shall be free from defects in materials and workmanship under normal use and ser
19. s original shipping container User s Manual February 2015 ELP 362D Emergency Locator Beacon 16 D RJE International 15375 Barranca Pkwy Ste 112 Irvine CA 92618 USA ELP 362D UNDERWATER LOCATOR BEACON P N 00172 or P N 008400 OPTIONAL BATTERY REPLACEMENT KIT B362 D90 01 INSTRUCTIONS IT IS RECOMMENDED TO USE THIS KIT WITHIN 7 YEARS OF THE BATTERY DATE STAMPED HERE The battery replacement kit includes a lithium battery P N 362 99000 1 O Ring P N 362 69001 O Ring lubricant tube P N 999 00026 replacement instructions P N 362 19001 4 and 90 DAY BATTERY MMM YY LL label P N 362 59002 Battery replacement must be conducted by the latest date stamped on the pinger label Remove the ELP 362D from the mounting bracket assembly and perform the Alternative Battery Check as described in the ELP 362D s User s Manual found in Section 3 under Pre Deployment Tests If the measured voltage is less than 6 0 Volts DO NOT remove the battery access end cap Return the ELP 362D to RJE International for service A WARNING Failure to observe these precautions could result in the release of hazardous chemicals If the measured voltage is 6 0 Volts or more proceed with the following battery replacement instructions STEP A Using the RJE International torque adapter B362 09111 i remove the end cap marked BATTERY ACCESS NETR uN WARNING Do not clamp the pinger in a vice YEAR OF BATTERY MANUFACTURE 00 99 STE
20. th a standard mounting bracket kit P N B362 05591 and a customer specific mounting bracket kit P N B362 08530 Either kit allows the beacon to be securely mounted Please contact RJE INTERNATIONAL INC if the standard mounting bracket does not meet your needs The beacon and its standard mounting bracket are shown in Figure1 1 The beacon is also shown installed in its standard mounting bracket in Figure 1 2 and a dimensional outline of the beacon is shown in Figure 1 3 This section provides a general descriptive overview of the beacon its theory of operation and use User s Manual February 2015 ELP 362D Emergency Locator Beacon ELP 362D USER S MANUAL Wa PN 001722 30 DAY STANDARD PN 008400 90 DAY OPTIONAL MOUNTING BRACKET ASSEMBLY OPTION B362 05591 CPN 006186 User s Manual Figure 1 1 ELP 362D and Mounting Bracket February 2015 ELP 362D Emergency Locator Beacon 3 WATER SWITC Figure 1 2 ELP 362D Installed in Mounting Bracket External Construction The beacon is contained in a water tight aluminum case capable of withstanding high impact shock and deep water immersion As shown in Figure 1 2 one of the end caps has a water activated built in switch that causes the beacon to begin transmitting when the switch comes in contact with water 01 30 3 92 Figure 1 3 ELP 362D Dimensi
21. vice when correctly installed used and maintained for a period of 60 months from date of shipment from RJE International Inc Purchaser s receipt of any product delivered hereunder shall be an unqualified acceptance of and a waiver by Purchaser of the right of Purchaser to make a claim with respect to such product unless Purchaser gives RJE International Inc notice of any claim within 60 months after the receipt of such product This warranty is limited to repair or replacement of the said product at RJE International Inc plant in Irvine CA providing the product was not abused or operated other than in accordance with the RJE International Inc Inc instruction manuals Since all RJE International Inc oceanographic instruments are pressure tested to rated depth prior to shipment RJE International Inc does not assume responsibility for any damage due to leakage or implosion RJE International Inc reserves the right to modify its warranty at any time in its sole discretion THIS LIMITED WARRANTY IS NOT TRANSFERABLE LIMITATION OF LIABILITY RJE International Inc MAKES NO OTHER WARRANTY REGARDING ITS PRODUCTS OR THE PRODUCTS OF OTHERS EITHER EXPRESS OR IMPLIED AND ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEEDS THE FORGOING WARRANTIES IS HEREBY DISCLAIMED BY RJE International Inc AND EXCLUDED FROM ANY AGREEMENT MADE BY ACCEPTANCE OF ANY ORDER RJE International Inc DOES NOT ACCEPT LIABILITY BEYOND THE REME
Download Pdf Manuals
Related Search