USER MANUAL - MCM Electronics
Contents
1. Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors e Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically e If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service e Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS WARRANTY One year from date of purchase OPERATING DETE2. Operations Static colour mode Press the mode button to show C01 on the LED display and use the UP and DOWN buttons to select one of the 15 colours see overleaf for the built in colour chart MODE Down UP Built in programme mode Press the mode button to show P01 on the LED display and use the UP and DOWN buttons to select one of the 9 built in programmes see over leaf for built in programme chart MODE Down UP Sound active mode Press the mode button to show S99 on the LED display and use the UP and DOWN buttons to select the sound sensitivity level from 00 99 00 low 99 high DMX mode Press the mode button to show Add on the LED display and use MODE Down UP the UP and DOWN buttons to select the DMX address from 001 512 a Slave mode To set unit s into the slave mode press the mode button to show Add on the LED display and use the UP and DOWN buttons O O to set the DMX address to 001 The slave units will now follow in sequence with the master unit MODE Down UP DMX channel selection Press the mode button to show 4CH on the LED display and use the UP and DOWN buttons to select between 4 or 6 channel mode see overleaf for DMX functions MODE Down UP Q COLOUR CHARTS Built in colour chart C01 Red C06 Purple C11 Light Blue C02 Green C07 Cyan C12 Light Yellow C03 Blue C08
3. www prolight co uk COLOUR Order code LEDJ210 USER MANUAL Q COLOUR SAFETY WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this eguipment away from rain moisture and liguids SAFETY INSTRUCTIONS Every person involved with the installation operation 8 maintenance of this eguipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the eguipment To maintain the eguipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this eguipment are not subject to warranty Q COLOUR SAFETY IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment e Do not open the equipment and do not modify the equipment
4. White RGB C13 Magenta C04 White W C09 Pink C14 Light Cyan C05 Yellow C10 Light Green C15 White RGBW Built in programme chart rs KETT st see O 4 channel DMX chart CHANNEL VALUE FUNCTION 000 255 RED 0 100 000 255 GREEN 0 100 000 255 BLUE 0 100 000 255 WHITE 0 100 6 channel DMX chart Q COLOUR DMX SET UP DMX 512 e DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX Linking e DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address
5. 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation e The A Colour can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output figure 1 Figure 1 Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight dealers Please quote CABL10 2M CABL11 5M CABL12 10M Also remember that DMX cable must be daisy chained and cannot be split Q COLOUR DMX SET UP Notice e Be sure to follow figures 2 8 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 in 3 pin XLR XLR Pin Configuration Pin 1 Ground DMX 512 out 3 pin XLR XLR MALE SOCKET XLR FEMALE SOCKET 2 cold 1 ground Pin 2 Negative I 1 H 1 O 2 cold ES 1 1 1 1 1 i 1 Len FIGURE 3 FIGURE 2 Special Note Line termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission problems O and interferance it is always advisable to connect a e O DMX terminal resistance 120 Ohm 1 4 W b
6. RMINATIONS Ifthis equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property Q COLOUR INTRODUCTION Introduction CONTROL FEATURES e DMX channels 4 6 selectable e Blackout Dimmer Strobe e Individual control of Red Green Blue and White LEDs Features 18 x 8W Quad colour LEDs e RGBW colour mixing e Static colour selection built in programmes sound active and DMX modes e Power consumption 145W Long life LEDs e Master Slave e Fan cooled e Robust metal housing e Power supply 240V e Dimensions 153 x 344 x 222mm e Weight 4 7Kgs Overview Fuse F2A 250V Power out Power in 100 240V AC O 50 60Hz O O o O Oo o DMX in DMX out 0 COLOUR 000 O O MODE DOWN uP Operating Instructions The Q Colour is a DMX 512 controllable full RGBW colour mixing wash made up of high efficiency and super bright LEDs There are four colour groups red green blue and white whose intensity can be controlled individually allowing the creation of an unlimited range of colours The Q Colour will operate in stand alone Master Slave sound activated and DMX Q COLOUR OPERATIONS
7. etween pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number CABL90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The chart below details the correct cable conversion 5 Pin XLR socket Pin 1 GNI sareen Pin 2 Signal Pin 3 Signal Pin 4 Pin 5 N C 3 Pin XLR socket Pin 1 GNI EH Pin 2 Signal Pin 3 Signal 5 Pin XLR socket Pin 1 GND screen 3 Pin ALR socket Pin 1 GNI aial Pin 2 Signal R Pin 3 Signal El S Ne in 5
Download Pdf Manuals
Related Search