User Manual - Universal Fiber Optic Lighting LLC
Contents
1. Outputs white V43 M56 M63 light Vega Illuminator Range CONNECTION VEGA CDMX amp VEGA TDMX There are 3 connections required the fiber port the mains supply cable and the DMX control cable The fiber port should be connected first Connect and secure the fiber optic connector into the green collar and secure using the M5 locking screw Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket Switch on power The LED Indicator will illuminate and the illuminator is ready for use If no light is produced consult the TROUBLESHOOTING section To revert to normal manual operation of the wheel remove top cover to access the dip switch on the PCB Set switches 1 to 9 off and switch 10 on Replace the cover NOTE THESE ILLUMINATORS ARE NOT MAINS DIMMABLE For DMX control connect up the DMX control cables to the Mini XLR sockets on the rear of the Illuminator The recommended plug for these sockets is Multicomp SVP556 TA The pin out details for the plugs are shown below DMX SCREEN SCREEN DMX DMX Plug viewed from rear inside Socket pins NOTE It is recommended that a 1200hm terminating resistor be connected across DMX and DMX on the last illuminator in the DMX universe or cable run Universal Fiber Optics REMOTE DMX CONTROL To set the DMX address remove the top cover to access the Dip switch on the PCB Set the address as detailed below and2. Connect and secure the fiber optic connector into the green collar and secure using the M5 locking screw Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket Switch on power the led Indicator will illuminate and the illuminator is ready for use If no light is produced consult the TROUBLESHOOTING section NOTE THESE LIGHT SOURCES ARE NOT MAINS DIMMABLE Connect up the 0 10V control cable to the mini XLR sockets on the rear of the illuminator The recommended plug for these sockets is the Multicomp SVP556 TA The pin out details for these plugs are shown below Socket pins Plug viewed from rear inside 0 10V Control is available to either control a color wheel VEGA C 0 10V or control a Twinkle wheel VEGA T 0 10V a Vega Illuminator Range The value tables for the the 0 10V control is shown below Function Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel NOTE Value Description a 23V Returns to White Color 1 For Twinkle wheel control use values marked Universal Fiber Optics o MAINTENANCE Please Note that a record of all maintenance MUST be kept in the table below indicating what maintenance was undertaken and when This MUST be dated for warranty purposes Maintenance Undertaken so Vega Il
3. replace the top cover Connect up the Illuminators with the Remote Controller using the Mini XLR sockets provided on the back of the Illuminator it doesn t matter which socket is used DMX ADDRESS The DMX address of each Illuminator is set manually using the DIP switch on the PCB as shown below DIP DIP Switches Switches l On 2 Off 3 Off 4 On 5 Off Dip Switch Number Bm PIT Above Example 6 On T On 8 Off Address 105 9 Off 10 Off O Vega Illuminator Range VEGA CDMX Color Wheel Each Illuminator occupies 2 channels as detailed below Channel Function Value Description White Snap to color Color 1 Yellow Snap to color Color 2 Green Snap to color Color 3 Orange Snap to color Color 4 Magenta Snap to color Color 5 Blue Snap to color Color 6 Color Wheel fso Magenta Snap to color Color 5 Color Wheel 90 Orange Snap to color Color 4 Green Snap to color Color 3 Yellow snap to color Color 2 White Snap to color Color 1 Fast to slow rotation counter clockwise Vega T DMX Twinkle Wheel Channel Function NET Description 0 255 From OFF at 0 to Brightest at 255 Motor Control From stop at 0 to fastest at 255 3 4rpm Universal Fiber Optics a CONNECTION VEGA C 0 10V VEGA T 0 10V There are three connections required the fiber port the mains supply cable and the 0 10V control cable The fiber port should be connected first
4. CM amp VEGA TM There are 2 connections required the fiber port and the mains supply cable The fiber port should be connected first Connect and secure the fiber optic connector into the green collar and secure using the M5 locking screw Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket Switch on power the led Indicator will illuminate and the illuminator is ready for use If no light is produced consult the TROUBLESHOOTING section NOTE THESE ILLUMINATORS ARE NOT MAINS DIMMABLE NORMAL OPERATION VEGA CM amp VEGA TM The VEGA CM Colorwheel amp VEGA TM Twinkle Wheel have manual speed control on the decorative motor Under normal operation the decorative wheel motor speed can be adjusted manually using the control on the rear of the unit Motor speed can be adjusted from STOP to approximately 4 RPM To revert to normal manual operation of the wheel remove top cover to access the dip switch on the PCB Set switches 1 to 9 off and switch 10 on Replace the cover The standard decorative color wheel has 6 glass segments as follows White Clear Yellow Green Orange Magenta Blue Alternatively a 6 segment or 4 segment vari color wheel can be fitted providing the following color segment options Orange Golden Amber Apricot 018 059 014 Green Jade Turquoise G78 G96 C47 Italian Blue Brilliant Blue Bright Blue Congo C45 B06 B28 B93 Violet Magenta Pink Clear
5. Illuminator User Guide MEO Vega Decorative Illuminator Range Models covered by this manual UFO VEGA UFO VEGA CM UFO VEGA TM UFO VEGA CDMX UFO VEGA TDMX UFO VEGA C 0 10V UFO VEGA T 0 10V Please read this manual fully before installing operating or performing maintenance on the illuminator unit Universal Fiber Optic Lighting LLC 6119A Clark Center Avenue Sarasota FL34238 Tel 941 343 8115 Fax 941 296 7906 Issue 1 Revised 12022014 www fiberopticlighting com INTRODUCTION Thank you for purchasing this UFO Illuminator Please read these instructions fully before connecting your unit to the electrical supply and keep them for future reference The UFO Vega range of illuminators are suitable for use with either glass or PMMA fiber optic harnesses The Vega is powered by a 100 240 VAC remote desktop power supply unit IMPORTANT THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED x Vega Illuminator Range INSTALLATION INSTRUCTIONS POWER SUPPLY REQUIREMENTS The LED Illuminator is powered from a multifunction multi voltage desk top Power Supply Unit Remove the 24V Desk Top PSU from its box This PSU is an IEC input device catering for UK European and USA mains supplies using the relevant power cord VEGA Universal Fiber Optics a CONNECTION VEGA
6. e controller fault Not Responding No 0 10v signal at illuminator due to cable or controller fault Illuminator dimmed either manually or by DMX or 0 10v Poor light output on fiber control LED driver failure Replace Illuminator Universal Fiber Optics Check and increase dimmer settings as appropriate TECHNICAL SPECIFICATIONS Description Details l 6 18 L x 6 38 W x 4 57 H Size 157mm L x 162mm W x 116mm H ne Vega Illuminator Range NOTES Universal Fiber Optics NOTES 14 Vega Illuminator Range NOTES Universal Fiber Optics as UNIVERSAL FIBER OPTICS Universal Fiber Optic Lighting LLC 6119A Clark Center Avenue Sarasota FL34238 Tel 941 343 8115 Fax 941 296 7906 www fiberopticlighting com
7. luminator Range TROUBLESHOOTING Problem Probable Causes Remedy Mains supply off Check supply amp reinstate Unit is dead no light output Check plugs and LED power indicator on PSU is not illuminated Plug fuse blown UK Check fuse If blown replace PSU failed Replace PSU Unit is dead no light output and LED power indicator on PSU i is illuminated but LED indicator Zul Sa a on Illuminator not illuminated For White Light Manual 4 tti Adjust brightness on dimmer aa Dimming control at minimum Dimming Version control at rear en DIP switch no 10 not switched Remove cover and switch DIP Unit is dead no light output ON COLON but LED power indicator is illuminated LED array or drive failure Replace illuminator For Decorative Manual Motor AZ Adjust motor control at rear Version DIP switch No 10 not switched Remove cover and switch DIP ON switch No 10 to ON D i heel n rnin cole j ecorative wheel not turning A Replace Illuminator Remove cover and switch DIP DIP switch No 10 is switched ON switch No 10 to OFF DMX address not correctly set Fe abate ul lin For Decorative DMX adaress Check DMX controller for correct Wiring fault on DMX cables cles cables and repair as required Driver circuit failure Replace Illuminator DIP switch No 10 is switched Remove cover and switch DIP For Decorative 0 10v control OFF switch No 10 to ON Check input to Illuminator using a DMM set to correct range rectify cabl
Download Pdf Manuals
Related Search