1 - Elhvb.com
Contents
1. 3 3 128K Direct Mapped Cache CC lt lt 328 nn GR 3208 mop 5 b 3208 Figure 3 3 128K Direct Mapped Cache NOTE 128K Direct Mapped Cache option is achieved by installing four 32 8 SRAM DATA RAM DIPs at M2 to M5 and one 8Kx8 SRAM TAG RAM 28 pin at M6 d n X mamana 256K Direct Mapped Cache M M6 M7 32Kx8 2 32Kx8 EN M8 32Kx8 M3 32Kx8 Figure 3 4 256K Direct Mapped Cache NOTE 256K Direct Mapped Cache option is achieved by installing eight 32Kx8 SRAM DATA RAM DIPs at M2 to M5 and M7 to M10 and one 32Kx8 SRAM TAG RAM 28 pin at 6 System M emory 3 5 THIS PAGE INTENTIONALLY LEFT 3 6 System emory Chapter 4 Award BIOS Setup System Setup A SETUP program builtinto the system BIOS is stored in the CMOS RAM that allows the configuration settings to be changed This program is executed when User changes system configuration User changes system backup battery e System detects a configuration error and asks the user to run the SETUP program After power on RAM testing the message below appears TO ENTER SETUP BEFORE BOOT PRESS CTRL ALT ESC or DEL key Press CTRL ALT ESC or2. To configure AutoCAD 11 386 1 Run the FASTACAD BAT that was copied to the TurboDLD Classic sub directory by typing CATURBODLD FASTACAD Enter The above example shows that TurboDLD C assic was installed on drive C inthe TURBODLD sub directory 2 Start AutoCAD and reconfigure it to use TurboDLD Classic by selecting option 5 Configure AutoCAD from the AutoCAD main menu From the next menu select option 3 Configure Video Display Choose Item 1 P386 ADI 4 0 4 1 R11 as your display device For more information see your AutoCAD Installation and Performance Guide GEM 3 0 To install the GEM drivers the first step is to create a diskette file known as the GEM driver pak 1 Using the standard DOS FORMAT utility format a blank diskette by inserting it in drive A and typing the following FORMAT Enter The DOS format utility will then prompt for the volume label by displaying Volume Label 11 characters max Press Enter for none At this prompt type the following volume label name in upper case GEM DRIVRPK Enter UTILITY and DRIVERS 6 7 6 8 Using the DOS COPY utility copy the following files from the GEM 3 system master diskette comes with GEM 3 to the newly formatted GEM DRIVRPK diskette Type the following sample commands assuming that the GEM 3 system master diskette is in drive A and the GEM DRIVRPK diskette is in drive B COPY A GEMVDI EXE B Enter COPY A MDGEM SYS B Ente
3. Default 2 3 23 3333 33 EET Tae ie fre on on eowsoxzo amor 2 oo on Ton m s Ha 80487 20 1 2 1 2 2 I 2 OFF OFF 40 00 804868 33 2 3 2 3 2 3 2 3 OFF OFF 33 33 80486SX 25 804865X 20 1 2 2 3 2 3 40 00 Table 2 6 Cache Selection ISA VESA Expansion Slot Connector The motherboard provides one ISA VESA expansion slot connector The following list gives a detailed arrangment and pin outs of this slot Side of the connector are the component pin outs on the board Side B of the connector are the solder pin outs on the board Connector Side A pins and pin outs Side pins SLOT1 01 412V 01 02 Ground 03 Ground IOCHCK 05 SD7 06 06 07 05 08 04 09 03 10 502 10 11 01 11 12 00 12 13 IOCHRDY 13 14 AEN 14 15 LA19 15 16 LA18 16 17 LA77 17 18 LA76 18 19 SA15 19 20 SA14 20 21 SA13 22 SA12 23 5 7 7 24 SA10 25 SA9 26 SA8 27 SA7 28 SA6 29 SA5 30 SA4 31 SA3 32 SA2 33 SA1 34 SAO 35 Ground 36 Ground 37 5V 38 SBHE 39 LA23 40 LA22 41 LA21 42 LA20 43 LA19 44 LA18 45 LA17 46 47 MEMW 48 08 49 509 50 010 51 011 52 012 53 013 54 014 55 5015 56 Ground 57 Ground 58 Ground 59 LDEV1 _ 60 GNL Table 2 7 ISA VESA Slot Connector Ground Ground 5V LREQ1 IN M otherboard Setting
4. HDD Signal Ground J20 Turbo LED LED LED J21 Turbo Switch Ground Turbo signal J22 Reset Switch J23 Speaker Connector J24 Power LED amp Key lock Ground Reset signal Speaker signal NC Ground Power LED Ground Keyboard clock Ground Table 2 1 Connector Description Continued d Motherboard Settings Jumper Function Open Close J9 IOCHRDY No IOCHRDY for Hard Disk IOCHRDY J16 BALE No BALE for Hard Disk BALE Software RTC Clear Clear Clear For AWARD For AMI A20 Gate Fast A20 KB A20 Address Decode Normal WEITEK for WEITEK Interface TABLE NOTE Default Table 2 2 System Setting wal VESA BUS setting wait state Ve vesa Bus seting CPU lt _ TABLE NOTE Default Table 2 3 Video Setting VGA gt 33MHz NOTE To upgrade display memory to 2MB install 8 pieces of DIP 44256 70 DRAM at MI 1 to M18 M otherboard Settings 2 5 1 2 0 short 1 open IMI 425 5 6 7 8 Clock MHz 24 32 40 50 80 66 6 66 6 Test 16 20 25 40 50 33 3 Default PW DN e Jo Table 2 4 Clock Setting 2 6 M otherboard Settings a 804860x 33
5. 1992 American Megatrends Inc All Rights Reserved Date mn date year Fri Jun 11 1993 Base memory 640 KB Time hour min sec 11 32 03 3072 Head WPcomLZone Sect Size Hard Disk C Type 17 977 5 300 977 17 41 Hard Disk Not Installed Floppy Drive A 1 2 51 4 Floppy Drive Not Installed Primary Display VGA PGA EGA Keyboard Installed Month Jan Feb Dec Date 01 02 03 31 Year 1901 1902 2099 Sun Mon Tue Wed Thu Fri Sat 26 27 28 29 30 31 1 4 11 714 815 ESC Exit 4 1 Select F2 F3 Color PgUp PgDn Modify The standard CMOS SETUP screen is shown above System BIOS automatically detects memory size thus no changes are necessary After the changes are made press Esc to exit The SETUP program is completely menu driven Use the arrow keys to select an entry PgUp PgDn keys to change an entry and Esc key to exit Help messages are displayed in a window on the screen when Alt FI is pressed 5 2 AMI BIOS Setup Advanced CMOS SETUP AM1 BIOS SETUP PROGRAM ADVANCED CMOS SETUP 1992 American Megatrends Inc All Rights Reserved Typematic Rate Programming Disabled Adaptor ROM Shadow 0000 32K Disabled Adaptor ROM Shadow D800 32K Disabled Typematic Rate Chars Sec Adaptor ROM Shadow E000 64K Disabled Mouse Support Option Boot Sector Virus Protection Enabled Above 1 MB Memory Test Disabled BIOS C
6. Move the cursor to where VGA appears on the list and choose SELECT 6 A sub menu will appear listing all the choices of resolutions supported by the graphics driver Select the desired resolution WordStar 5 5 7 0 2000 V 3 5 1 you have not already done so install WordStar onto your computer system Follow the instructions supplied with WordStar 2 Run the installation program INSTALL EXE and choose the option for the WordStar drivers and specify the drive and directory where you want them copied to such as C WS 3 Using a text editor enter the file FONTID CTL in the directory and change the CRT TYPE line to read CRT TYPE CL800 WGD UTILITY and DRIVERS 4 When WordStar is executed the display driver will be used for page preview mode No of Screen Display Pixel Horizontal Colors Format Mode Frequency Frequency MHz xt 14 360x400 720 400 Text 28 320x200 Graphic 12 5 31 5 640x200 Graphic 25 31 5 720x400 Text 28 31 5 320x200 Graphic 31 5 640x200 Graphic 25 31 5 640x350 Graphic 25 31 5 640x350 Graphic 25 31 5 640x480 Graphic 31 5 640x480 Graphic 31 5 640x480 Graphic 37 9 320x200 Table 6 1 Standard Video Modes NOTE Vertical Frequency 70Hz UTILITY and DRIVERS 6 19 VESA No of Mode No No Colors 14 161256 lt 54 10 16 256 55 109 16 256K 58 6A 10
7. Parallel port LPT DO LPT D1 LPT D2 LPT D3 LPT D4 LPT D5 LPT D6 LPT D7 LPT acknowledge LPT busy Paper end Selected status Auto line feed LPT error Initiate printer Select printer Ground 1 RAIN Horizontal sync Vertical sync NG CN8 Density selection NG FDD Connector NG Index detection Select motor A Select drive B Select drive A Select motor B Direction control Step pulse Write data Write enable Track 0 Write protect Read data Head select Disk change Ground 13 15 17 19 21 23 25 27 29 31 33 Table 2 I Connector Description Continued EE ATT 2 2 M otherboard Settings Connector Pin Out Signal Name Reset hard disk IDE Connector Ground HDD7 HDD8 HDD6 HDD9 HDD5 HDD10 HDD4 HDD 11 HDD3 HDD12 HDD2 HDD13 HDD 1 HDD14 HDD6 HDD15 Ground NC Ground HD write Ground HD I O read Ground IOCHRDY HD address latch NC Ground IRQ14 IOCS16 HD AI NC HD AO HDA2 HD chip select 0 HD chip select 1 HD active Ground OONOOBRWN Table 2 1 Connector Description Continued M otherboard Settings 2 3 Connector Pin Out 1 8514A Connector 2 4 6 16 18 20 22 25 3 Signal Name VPO Ground VP1 VP2 VP3 Enable video data VP4 Enable sync signal VP Enable video dot clock VP6 VP7 Video dot clock Banking Horizontal sync Vertical sync NG NG J13 HDD LED
8. completely menu driven Use the arrow keys to select an entry PgUp PgDn keys to change an entry and Esc key to exit Help messages are displayed in a window on the screen when Alt FI is pressed 5 2 AMI BIOS Setup Chapter 5 BIOS Setup System Setup A SETUP program built into the system BIOS is stored in the CMOS RAM that allows the configuration settings to be changed This program is executed when User changes system configuration User changes system backup battery e System detects a configuration error and asks the user to run the SETUP program After power on RAM testing the message below appears Press DEL if you want to run SETUP Press DEL to run setup or do nothing to bypass If the DEL key is pressed the following screen is displayed AMI BIOS SETUP PROGRAM BIOS SETUP UTILITIES 1992 American Megatreads Inc All Rights Reserved STANDARD CMOS SETUP ADVANCED CMOS SETUP AUTO CONFIGURATION WITH BIOS DEFAULTS AUTO CONFIGURATION WITH POWER ON DEFAULTS CHANGE PASSWORD AUTO DETECT HARD DISK HARD DISK UTILITY WRITE TO CMOS AND EXIT DO NOT WRITE TO CMOS AND EXIT Load BIOS Setup Default Values for Advanced CMOS and Advanced CHIPSET Setup ESC Exit 1 3 T Sel F2 F3 Color F10 Save amp Exit Use and f keys to select and press Enter to run your selection AMI BIOS Setup 5 1 Standard CMOS SETUP AMI BIOS SETUP PROGRAM STANDARD CMOS SETUP
9. of the drivers and modes of operation If you have been using a driver supplied with another graphics adapter you may want to make a backup copy of the INSTALL DDF file currently in your 2 3 directory COPY INSTALL DDF INSTALL BAK Enter Run the installation program INSTALL EXE and choose the option for the version of Lotus 1 2 3 that you are using and specify the drive and directory where you want them copied to such as C 123R3 If the INSTALL DDF has been copied to backup file see step 2 above answer YES to the prompt to confirm overwriting the file Run the Lotus installation utility by typing INSTALL Enter Select Change selected equipment from the list If you are currently using another driver supplied with graphics board it may be necessary to choose First time 6 10 installation Select Modify Current DCF or Choose another DCF to modify according to your preference The following procedure is valid for either selection Select Change Video Display This will present you with list of all the display types provided with the 1 2 3 distribution with two additional choices GD542x100 Column Display 800x600 resolution supports 100x31 100x42 and 100x75 16 color modes GD542x128 Column Display 1024x768 resolution supports 128x40 128x54 and 128x96 16 color modes Select a resolution that best meets your requirements UTILITY and DRIVERS 8 After your selection is m
10. this happens enter if this diskette is in the A drive If you see the message Problem with disk drive A and the installation disk is in drive B press ESC twice and re enter B in the space provided 7 When Setup is complete you are returned to the MS DOS prompt Type win to start Windows AutoCAD 9 10 11 12 1 Insert the Display drivers diskette into Drive A or Run the installation program INSTALL EXE and choose the option for the Autodesk AutoCAD drivers and specify the drive and directory where you want them copied to such as C ACAD DRV Since the start up is a little bit different for AutoCAD Release 12 than it is for older versions please follow the instructions for the version of AutoCAD you will be using TurboDLD Classic with To configure AutoCAD 12 1 Begin AutoCAD with the reconfigure switch by typing ACAD R Enter 2 Choose option 3 Configure Video Display from the AutoCAD configuration menu UTILITY and DRIVERS 3 the Do you want to select message to display the available video options for AutoCAD 4 Select TurboDLD Classic by Panacea Inc from the list of display options NOTE If you chose to install TurboDLDClassic into a sub directory other than ACADVDRV be sure to modify the ACADDRV environment variable to include that sub directory Otherwise the TurboDLD Classic selection will not appear in the list of available drivers
11. 05426 8514A Connector DRAM 120 pin Expansion ler Control slot SYSTEM ADDRESS BUS SA 8742 Keyboard Controller Controller serial port1 o parallel port PDC IDE 20230 FDD Local IDE Figure 1 2 System Block Diagram 1 4 Overview Chapter 2 Motherboard Settings Connector Pin Out Signal Name CN1 Power connector 10 12 Power go 5V 12V 12v Ground 45V CN2 PS 2 Keyboard Keyboard data NG Ground Keyboard clock NG CN3 PS 2 Mouse Mouse data NG Ground Mouse clock Ground CN4 Serial Port1 CO Data carrier detect Receive data Transmit data Data transmit ready Ground Ready to receive data Request to send data Clear to send Ring indicator Serial Port 2 CO WY Data carrier detect Receive data Transmit data Data transmit ready Ground Ready to receive data Request to send data Clear to send Ring indicator Table 2 1 Connector Description M Motherboard Settings 2 Connector __ Pin Out Signal Name CN6 LPT strobe
12. 2 t8 x Hz 800x600 0 z56 1 60 2 272 tl x Hz 1024x768 0 87i 1 260 2 70 3 72 t2 x Hz 1280x1024 0 87i 1 available For example to select mode 3 for Super VGA monitor montype 2 type the following command at the DOS prompt CLMODE 3 m2 Enter To select custom monitor timings with 640x480 at 60Hz and 800x600 at 72Hz refresh type CLMODE 16 0 t8 2 Enter Typing an invalid option will display the command line help text Typing as command line option will display the current Cimode settings Software Drivers Windows 3 0 3 1 1 Exit Windows 2 From the DOS Prompt e g C gt change the directory to the Windows directory e g CD WINDOWS 3 Type setup at the MS DOS prompt UTILITY and DRIVERS 6 5 4 After setup has executed you will be presented with a screen which shows the current Windows configuration Move the Jeu selection bar to the Display entry Press ENTER which lists the available display adapters which you may select for use with Windows will be presented Move the highlight bar down to the entry marked other Requires disk provided by a hardware manufacturer Type in the source drive of the Windows 3 0 3 1 Drivers diskette Select the desired screen resolution and press Enter Setup will copy files from the diskette into your Windows directories You may be prompted for the Driver Disk files subdirectory When
13. 2 16 256K 58 6 102 16 256 58 6A 102 16 256K 5C 103 256 256K 5c 103 256 256K 5C 103 256 256K 50 104 16 256 50 104 16 256 50 104 16 256 50 104 16 256 101 256 256 101 256 256 60 105 256 256 60 105 256 256 60 105 256 256 60 105 256 256 64 111 64K 64 111 64K 65 114 64K 65 114 64K 66 110 32k 66 110 32K 67 113 32K 6C 106 16 256K 6D 256 256K 6F 10E 40x25 70 10F 16M 71 112 16M 74 64K Char x Char Screen Pixel IHorizontal Vertical Row Cell Format Freq Frequency Frequenzy MHz KHz Hz 132x25 8x16 1056x400 41 5 31 5 70 132 43 8x8 1056x350 41 5 31 5 70 132x25 8x14 1056x350 41 5 31 5 70 100x37 8x16 800x600 36 35 2 56 100x37 8x16 800x600 40 37 8 60 100x37 8x16 800x600 50 48 1 72 100x37 8 16 800x600 36 35 2 56 100x37 8x16 800x600 40 37 9 60 100x37 8x16 800x600 50 48 1 72 128x48 8x16 1024x768 44 9 35 5 128x48 8x16 1024x768 65 48 3 60 128x48 8x16 1024x768 75 56 70 128x48 8x16 1024x768 77 58 72 80x30 8x16 640x480 25 31 5 60 80x30 8x16 640x480 31 5 37 9 72 128x48 8x16 1024x768 44 9 35 5 128x48 8x16 1024x768 65 48 3 60 128x48 8x16 1024x768 75 56 70 128x48 8x16 1024x768 77 58 72 640 480 50 31 5 60 640 480 63 37 9 72 800x600 72 35 2 56 800 600 80 37 8 60 640x480 50 31 5 60 640 480 63 37 9 72 800 600 72 31 5 56 160 64 8x16 1280x10
14. 24 75 48 160x64 8x16 1280x1024 75 48 8x8 8x8 320x200 25 31 5 40 25 8x8 320x200 38 31 5 80x30 8x16 640x480 75 31 5 1024x768 44 9 35 5 6 20 Table 6 2 Extended Video Modes UTILITY and DRIVERS NOTE 1 Only Mode No 14 54 55 are in Text Display Mode 2 Some modes are not supported by all monitors The fastest vertical refresh rate for monitor type selected will be automatically used 3 character stands for 32K Direct Color 256 color Mixed Mode 4 character stands for Interlaced Mode UTILITY and DRIVERS 6 21 Appendix Hard Disk Specifications CONNER MODEL CAPACITY UNDER cao secron CP 30084 CP 30084E CP 30104 CP 30104H CP 30174 CP 30174E CP 30204 CP 30204F CP 30254 CP 3364 3544 CAPACITY CYLINDER SECTOR 120MB 1023 17 170MB 964 34 213MB 683 38 245MB 967 31 345MB 790 57 Hard Disk Specifications 1 QUANTUM LPS80AT LPS105AT LPS120AT LPS240AT ELS85AT ELS127AT ELS170AT SEAGATE MODEL CAPACITY CYLINDER DER HEAD ST3096A ST3120A ST3144A 245MB SECTOR HEAD SECTOR 10 8 12 9 2 Hard Disk Specifications AC280 AC2120 AC2200 AC2250 AC2340
15. 486 MAIN BOARD USER S MANUAL DOC No 12529 REVISION Al DATE November 1993 Table of Contents Chapter 1 Overview Specifications aig noxia PA Mot herboard Layout System Block Diagram Chapter 2 Motherboard Settings Connector Description System Setting Video Setting Clock Setting CPU Type Selection Cache Selection ISA VESA Expansion Slot Connector Chapter 3 System Memory Memory Configuration Cache Configuration Size 64K Direct Mapped Cache 128K Direct Mapped Cache 256K Direct Mapped Cache 9 9 a3 0 a o 5 a 9 0 s o o c Chapter 4 Award BIOS Setup System Setup rede 4 Standard CMOS Setup 4 2 BIOS and Chipset Features Setup 4 3 Load Setup Default 4 4 Load BIOS Default 4 4 Password Setting 4 4 Exiting SEP oase AGA ca 4 5 Chapter 5 AMI BIOS Setup System Selllp ya A 5 1 Standard CMOS Setup 5 2 Advanced CMOS Setup KER D3 Write to CMOS and Exit 5 4 Chapter 6 VGA Utility and Drivers 53 ici odere a NS een 6 3 Using CLMode s Menu driven Interface 6 3 Available Video Modes 6 3 Getting Help 6 4 Exiting the CLMode 6 4 Using CLMod
16. DEL to run SETUP The screen below appears ROM ISA BIOS VIA00000 CMOS SETUP UTILITY AWARD SOFTWARE INC STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC Quit 10 Save amp Exit PASSWORD SETTING IDE HDD AUTO DETECTION HDD LOW LEVEL FORMAT SAVE amp EXIT SETUP EXIT WITHOUT SAVE 1545 Select Item Shift F2 Color Time Date Hard Disk Type Use Tor Jor or e key to select and press ENTER to run your selection Award BIOS Setup Standard CMOS Setup The Standard CMOS SETUP has 10 items for setting Each item may have one or more option settings Move cursor to the desired item for setting Use the PgUp or PgDn keys to see the options available for the highlighted item ROM ISA BIOS VIA00000 STANDARD CMOS SETUP AWARD SOFTWARE INC Date mm dd yy Sat May 15 1993 Time hh mm ss 12 37 05 DAYLIGHT SAVING Disabled CYLS HEADS PRECOMP LANDZONE SECTORS Drive C User 81mb 611 16 0 0 17 Drive D Omb 0 0 0 0 Drive A 1 2M 5 25 in Drive B 1 44M 3 5 in Base Memory 640K 7168K Vi amp o EGA VGA OK 384K Halt on All Errors Total Memory 1 lt Select Item PgUp PgDn Modify Shift F2 Change Color F3 Toggle Calendar The Standard CMOS SETUP screen is displayed above System BIOS automatically detects memory size thus no changes are necessary Press F3 to show th
17. OS 2 s Device Driver Install utility from System Setup in the System Folder This copies the device drivers from the Driver and Utilities for OS 2 diskette to the hard disk Insert the Drivers and Utilities for OS 2 diskette into drive Double click on the Device Driver Install the System Setup folder System Setup is in the OS 2 System folder UTILITY and DRNERS Click on the Install button from the OS 2 2 0 Device Driver Installation pop up window The Select Device Drivers pop up window displays a list of device drivers To assist in determining what capabilities your monitor has refer to the section on Clmode Select the device driver to be installed from the list and click on the OK button Device drivers are copied to their corresponding directories Click on the Exit button then the Yes button If the current DISPLAY DLL is in use a dialog box will pop up to notify the user that changes will be in effect on the next reboot Click the OK button to exit the installation utility 3 Modify the CONFIG SYS file in the root directory so that OS 2 will install the correct device driver on the next reboot Click on the OS 2 System Editor icon from the Productivity folder which resides in the OS 2 System folder Once in the OS 2 System Editor click on File Open and select CONFIG SYS in the File box If CONFIG SYS is not displayed type in the correct path and file name in the Filename box i e CACONFIG SYS Clic
18. OS Setup S d Write to CMOS and Exit AMI BIOS SETUP PROGRAM BIOS SETUP UTILITIES 1992 American Megatrends Inc All Rights Reserved STANDARD CMOS SETUP ADVANCED CMOS SETUP AUTO CONFIGURATION WITH BIOS DEFAULTS AUTO CONFIGURATION WITH POWER ON DEFAULTS CHANGE PASSWORD Write to CMOS and Y N Y Write settings to CMOS and Exit ESC Exit J oT Sel F2 F3 Color 10 Save amp Exit After making the necessary changes under SETUP press Esc to return to the main menu Move cursor to Write to CMOS and Exit and press to change the CMOS SETUP If no changes were made press Esc again and press y to retain the CMOS settings e A 5 4 AMI BIOS Setup Chapter 6 UTILITY and DRIVERS The instructions in this chapter assume that you understand elementary concepts of MS DOS Before you attempt to install any drivers you should know how to format a diskette copy and delete files and understand MS DOS directory structure You should have made backup copies of the original diskettes and should be using the backup ones The 486 VAC V supplies drivers for DOS and Windows based programs These drivers will help you utilize and enhance your system s video subsystem Each drivers diskette contains a README file giving information on the diskette Read the file first by using any word processor in the non document or ASCII mode The installation utility is provided to facilitate t
19. S 2 From within the Lotus sub directory type INSTALL Enter 3 From the next menu select Advanced Options for Lotus 1 2 3 V2 2 or Change Selected Equipment for Lotus 1 2 3 V2 3 4 For V2 2 select Add New Drivers to Library and go to step 3 For V2 3 select Modify Current Driver Set and go to step 6 5 From the next menu select Modify Current Driver Set 6 From the next menu select one of the display and resolution configurations 7 From the next menu select Return To Menu 8 From the next menu select Save Changes 9 Enter the name you have selected for the driver set We recommend that the driver set name reflect or include the driver s resolution e g 132 43 NOTE The default driver set name assigned by the program is 123 SET You may create multiple driver sets with different display resolutions To run Lotus 1 2 3 with a specific driver set type 123 SETNAME Enter where SETNAME is the name of the desired driver set UTILITY and DRIVERS 6 9 Lotus 1 2 3 3 0 3 1 is assumed that Lotus 3 0 or 3 1 is already installed on your hard disk using the standard Lotus installation utility To install this driver make the directory containing 1 2 3 V 3 0 the current directory For example if I 2 3 is in the directory named 1233 then type the following command CD 123R3 Enter Look for file INSTALL DDF a text file used by the 2 3 installation utility containing information on each
20. VERS CImode The Clmode utility allows the user to define the type of monitor attached and set the video modes supported by the VGA Using Clmode s enu driven Interface At the DOS prompt type CLMODE Enter The main popup window consists of a number of buttons Each button represents a different option or menu The underlined letter of a button name specifies the hot key combination for that item For example press the Alt and the underlined letter keys simultaneously or just the underlined letter key to select an option NOTE If you intend to use a mouse with Clmode then a mouse driver should first be installed prior to running the Clmode utilitv Available Video M odes Select the Video Mode button The Video Mode Preview window displays all the modes supported according to the monitor type attached and the amount of video memory present This list of video modes tells you which are available in your current configuration for use with extended resolution drivers To see what different video modes look like on your monitor select the Preview button After each test screen is displayed press Enter or the left mouse button to see the next video mode if you do not want to see any more video modes press Esc or the right mouse button will return you to the Video Modes Preview window The information in the main window displays the VGA controller type the BIOS version number and the amount of video memory presen
21. acheable Option Enabled Memory Test Tick Sound Enabled Video Cacheable Option Enabled Hit lt DEL gt Message Display Enabled 256K Relocate Option Disabled Hard Disk Type 47 RAM Area 0 300 ISA Bus Command Delay Disabled Wait For sF15 If Any Error Enabled ISA Slave Wait States 4 W S System Boot Up Num Lock On VO Recovery Time Disabled Floppy Drive Seek At Boot Enabled Extended ALE Disabled System Boot Up Sequence A C Decouple Refresh Enabled System Boot Up CPU Speed High FAST A20 PORT 92H Enabled Extemal Cache Memory Enabled COM 1 Select Enabled Internal Cache Memory Enabled COM2 Select Enabled Password Checking Option Setup Parallel port address 0378H Video ROM Shadow 32K FEnabled IDE Select Enabled Adaptor ROM Shadow 32K Disabled FDC Select Enabled Local IDE Drive Select Disabled Typematic Rate Delay msec Esc Exit 1T Sel Ctrl PgUp PgDn Modify F1 Help F2 F3 Color F5 Old Values F6 BIOS Setup Defaults F7 Power on Defaults Moving around the Advanced CMOS Setup program shown above is similar to moving around Standard CMOS Setup Users are not encouraged to run Advanced CMOS Setup program Your system should have been fine tuned before shipping Improper setup may cause the system to fail consult your dealer before making any changes NOTE Default values of the various Setup items on this chapter may not necessarily be the same ones shown on your screen AMI BI
22. ade choose the Save Changes option from the menu When some high resolution modes are selected a message may appear asking for the drive letter of the floppy disk Before entering the drive letter insert the disk that is requested in the floppy drive After inserting the disk you may enter the drive letter containing that diskette MS Word 5 0 The high resolution Microsoft Word 5 0 display driver supplied with your VGA supports both high resolution text and graphics When using a Microsoft Mouse with the driver please ensure that your mouse driver version level is 7 0 or above 1 you have not already done so install Microsoft Word onto your computer system Follow the instructions supplied with Word When asked for a screen display type choose IBM Video Graphics Array VGA 2 Run the installation program INSTALL EXE and choose the option for the Microsoft Word drivers and specify the drive and directory where you want them copied to such as C AWORD5 To use the new drivers they must be copied to the same directory as Word Otherwise they must be copied to the Word directory before they can be used 3 INSTALL EXE will copy two screen drivers SCREENS VID for 800x600 graphics resolution SCREEN VID for 1024x768 graphics resolution The driver to be used must be named SCREEN VID When a file is renamed this it will overwrite the existing display driver If you wish to preserve the original it should be ren
23. amed or copied prior to installation of the new drivers UTILITY and DRIVERS 6 11 0 2 R The new driver is now installed and to use it run Word as you normally would To view and change the screen resolutions select Options move the cursor to display mode and press F1 Choose the desired screen resolution from the list presented sub menu appears listing all the choices of resolutions supported by the text driver Select the desired resolution 2 0 16 Color Drivers This installation guide assumes the user to be familiar with the mouse interface of the OS 2 2 0 Desktop Shell environment 1 Save copy of the DISPLAY DLL OS2 DLL If you are currently running OS 2 2 0 open a DOS session by double clicking on a DOS Full Screen icon from OS 2 Command Prompts folder The Command Prompts icon is in the OS 2 System folder Move to the OS2 DLL directory by typing at the DOS prompt CD OS2 DLL Enter Type COPY DISPLAY DLL IBMVGA DLL B Enter at the DOS prompt to make a backup copy of the DISPLAY DLL If you are currently running MS DOS follow the above steps for a DOS session to make a backup copy of the DISPLAY DLL Return to the root directory by typing CD Enter and create a subdirectory in your OS 2 drive If you intend to install the 16 color drivers At the DOS prompt type md CL16DRV Enter Type C OS 2 BOOT 05 2 Enter to boot OS 2 to continue with the installation 2 Invoke
24. dPerfect allows graphics and text drivers to be set up separately so be sure to install both of these drivers To install the WordPerfect high resolution text driver supplied with your VGA follow these instructions 1 If you have not already done so install WordPerfect onto your computer system Follow the instructions supplied with WordPerfect 2 Run the installation program INSTALL EXE and choose the option for the WordPerfect drivers and specify the drive and directory where you want them copied to such as C WP51 3 Start WordPerfect and go into SETUP by typing Shift FI 4 Choose Display 2 then text screen type by pressing 3 UTILITY and DRIVERS 6 17 5 Move the cursor to where GD542X appears the list and choose SELECT 6 A sub menu will appear listing all the choices of resolutions supported by the text driver Select the desired resolution Toinstall the WordPerfect high resolution graphics driver supplied with your VGA follow these instructions 1 If you have not already done so install WordPerfect onto your computer system Follow the instructions supplied with WordPerfect 2 Run the installation program INSTALL EXE and choose the option for the WordPerfect drivers and specify the drive and directory where you want them copied to such as C WP51 3 Start WordPerfect and go into SETUP by typing Shift FI Choose Display 2 then graphics screen type by pressing 2 5
25. e drivers are copied to their corresponding directories UTILITY and DRIVERS Click on the Exit button then the Yes button If the current DISPLAY DLL is in use dialog box will pop up to notify the user that changes will be in effect on the next reboot Click the OK button to exit the installation utility 3 Modify the CONFIG SYS file in the root directory so that OS 2 will install the correct device driver on the next reboot Click on the OS 2 System Editor icon from the Productivity folder which resides in the OS 2 System folder Select Open from the File menu Open CONFIG SYS from the root directory Search for the command line which contains the library path and add the following subdirectory at the beginning of the path statement For example LIBPATH C CL32DRV i dene Search for the command line which contains sys For example DEVICE C OS2 MDOS VVGA SYS Select Find from the Edit menu Type VVGA SYS in the Find edit box Uncheck the Case Sensitive option if it is checked Click on the Wrap option so that a tick mark appears in the check box Click on the Find button Once the command line is located select the Cancel button Highlight the command line with the mouse then select Copy from the Edit menu Click at the end of the command line press the Enter key to insert a new line below the current command line Select ra from the Edit menu to make a copy of the command ine Type REM at
26. e calendar Daylight Saving When enabled this field allows user to set the clock one hour in advance When disabled it subtracts one hour from standard time After the changes are made press ESC to return to main menu gt 1 N Award BIOS Setup BIOS and Chipset Features Setup ROM ISA BIOS VIA00000 BIOS FEATURES SETUP AWARD SOFTWARE INC Virus Warning Enabled System BIOS Shadow Enabled CPU Internal Cache Enabled Video BIOS Shadow Enabled External Cache Enabled C8000 CBFFF Shadow Disabled Quick Power On Self Test Disabled CC000 CFFFF Shadow Disabled Boot Sequence AC D000 D3FFF Shadow Disabled Boot Up Floppy Seek D4000 D7FFF Shadow Disabled Boot Up Numlock Status D8000 DBFFF Shadow Disabled Boot Up System Speed DCOOO DFFFF Shadow Disabled IDE HDD Block Mode Disabled E0000 E3FFF Shadow Disabled Gate A20 Option Fast E4000 E7FFF Shadow Disabled Typem Rate Setting Disabled E8000 EBFFF Shadow Disabled Typematic Rate Chars Sec 6 Shadow Disabled Typematic Delay Msec 250 Security Option Setup Esc Quit Select Item F1 Help PgUp PgDn Modify F5 Old Values Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults ROM ISA BIOS VIA00000 BIOS FEATURES SETUP AWARD SOFTWARE INC ISA Command Delay Normal On board FDC Controller Enabled ISA Wait State Normal On board IDE Controller Enabled Reco
27. e s Command Line Options 6 5 Software Drivers 6 5 Windows 3 0 73 1 6 5 AutoCAD9 10 11 12 6 6 GEM kin AG aui o e 6 7 Kol EE NA qc oda SE BOR ait 6 9 Lotus 2 3 3 0 3 1 wash wag Goad Nai 6 10 MS Word 5 0 ee Yn La da 6 11 R g me we GR SINE dm ex 6 12 Ventura Publisher 2 x 3 0 6 1 6 WordPerfect 5 0 5 1 6 0 6 17 WordStar 5 5 7 02000V 3 5 6 1 8 Appendix Hard Disk Specifications A I List of Figures Figure l l Motherboard Layout 1 3 Figure 1 2 System Block Diagam 4 Figure 3 1 Cache Bank Location on Motherboard 3 2 Figure 3 1 64K Direct Mapped Cache 3 3 Figure 3 2 128K Direct Mapped Cache 3 4 Figure 3 3 256K Direct Mapped Cache 3 5 List of Tables Table 2 1 Connector Description 2 Table 2 2 System Setting 2 5 Table 2 3 Video Setting 2 5 Table 2 4 Clock Setting 2 6 Table 2 5 CPU Type Selectin 2 7 Table 2 6 Cache Selection 2 7 Table 2 7 ISA VESA Slot Connector 2 8 Table 3 IMemory Configuration 3 Table 3 2 Cache Configuration Size 3 2 Table 6 1 Standard Video Modes 6 19 Table 6 2 IExtended Video Modes 6 20 Chapter 1 Overview The 486 VAC V is a high performance All in O
28. he smooth installation of the display drivers The installation program is menu driven and allows you to select and install only those display drivers for software and application currently in use It is important to note that some display drivers need to have the associated vendor s application program already installed on the system prior to loading the VGA display drivers In other cases the loading of the display driver may be an integral part of the vendor s product installation process Please review the driver product section below for specific instructions prior to running the installation program The VGA card is supplied with software drivers for the following application programs 3D Studio 1 x 2 0 AutoCAD 9 10 11 12 AutoShade 1 2 0 e AutoSketch 3 x e Framework 2 3 UTILITY and DRIVERS 6 1 3 0 Lotus 2 3 2 x 3 0 3 1 MS Windows 3 0 3 1 MS Word 5 0 e OS 2R 2 0 e Ventura Publisher 2 x 3 0 e WordPerfect 5 0 5 1 e WordStar 5 5 7 0 e WordStar 2000 V 3 5 The installation utility is located on the diskette labeled Disk 1 To install the desired display drivers and utility insert the diskette into the A drive and type A Enter INSTALL Enter Follow the instructions on screen to install the listed display drivers At any time you may press Esc to abort the installation process and go back to DOS Selected drivers are simply copied to the specified disk and directory UTILITY and DRI
29. k on OK Search for the command line which contains the library path and add the following subdirectory to the beginning of the path statement For example LIBPATH C CLI6DRV Select Open from the File menu Open CONFIG SYS from the root directory Search for the command line which contains vvga sys For example DEVICE C OS2 MDOS VVGA SYS Select Find from the Edit menu Type VVGA SYS in the Find edit box Uncheck the Case Sensitive option if it is checked Click on the Wrap option so that a tick mark appears in the check box Click on the Find button Once the command line is located select the Cancel button Highlight the command line with the mouse then select Copy from the Edit menu Click at the end of the command line press the Enter key to insert a new line below the current command line Select Paste from the Edit menu to make a copy of the command line UTILITY and DRIVERS 6 13 REM at the beginning of the original command line Change VVGA SYS in the pasted command line to CLVSVGA SYS Select Save from the File menu and save the changes Double click on the SYSTEM icon to exit the editor Shutdown the system and reboot for the changes to take effect 32 Bit 256 Color Drivers This installation guide assumes the user has installed the Corrective Service Pack provided by IBM Also this installation assumes the user is familiar with the mouse interface of the OS 2 2 0 Desktop Shell environ
30. ment 1 Save a copy of the DISPLAY DLL in OS2 DLL If you are currently running OS 2 2 0 open a DOS session by double clicking on a DOS Full Screen icon from the OS 2 Command Prompts folder The command Prompts icon is in the OS 2 System folder Move to the OS2 DLL directory by typing at the DOS prompt OS2 DLL Enter Type COPY DISPLAY DLL IBMVGA DLL B Enter at the DOS prompt to make a backup copy of DISPLAY DLL If you are currently running MS DOS follow the above steps for a DOS session to make a backup copy of the DISPLAY DLL Return to the root directory by typing CD Enter and create a subdirectory in your OS 2 drive If you intend to install the 256 color drivers Type at DOS prompt md CL32DRV Enter Boot OS 2 to continue with the installation 2 Invoke OS 2 s Device Driver Install utility to copy device drivers from the Driver and Utilities for OS 2 diskette to the hard disk insert the Drivers and Utilities for OS 2 diskette in drive A Double click on the Device Driver Install icon in the System Setup folder The System Setup icon is in the OS 2 System folder Click on the Install button from the OS 2 2 0 Device Driver Installation pop up window The Select Device Drivers up window will display a list of device drivers To assist in determining what capabilities your monitor has refer to the Clmode section Select the device driver to be installed from the list and click on the OK button Devic
31. menu Ventura Publisher 2 x 3 0 1 Install Ventura Publisher V 2 0 as instructed in the product s manual specifying the Hercules driver 2 Insert the drivers diskette into Drive B Run the installation program INSTALL EXE and choose the option for the Ventura Publisher drivers and specify the drive and directory where you want them copied to such as Ventura Publisher requires that the drivers be installed from the root directory of a floppy disk in drive or drive B and then place the diskette in drive A before proceeding 6 16 UTILITY and DRIVERS 3 Change to drive by typing Enter After the A prompt appears run the VPDRV2 0 program by typing VPDRV2 0 Enter NOTE VPDRV2 O EXE can only be executed from the A drive Follow the step by step installation procedure as it appears on the screen and select one of the following drivers when prompted Cirrus Logic VGA 800x600 16 of 256K colors or greys Cirrus Logic VGA 1024x768 16 of 256K colors or greys Ventura Publisher V 2 0 is now configured for the selected screen resolution and 16 color graphics WordPerfect 5 0 5 1 6 0 To use high resolution modes with WordPerfect 6 0 install the VESA driver that comes with WordPerfect and configure the program to use one of the VESA high resolution graphics modes The high resolution WordPerfect version 5 1 driver supplied with your VGA supports both high resolution text and graphics Wor
32. ne motherboard offering outstanding features and performance for building advanced personal computers or workstations Based on ISA VESA BUS architecture this multi function board includes built in IDE and FDC interfaces The on board Cirrus Logic VGA controller is directly linked to the Local BUS providing enhanced video performance and Windows acceleration functions Specifications The 486 VAC V motherboard comes with the following features e Intel 80486SX DX DX2 and Intel 80487SX CPU in and PGA packages e VIA VT82C481 and VT82C495 Chipset e Supports 0 64 128 256K direct mapped write back cache memory e Supports 1 to 64 DRAM memory page mode DRAM operation e Shadow RAM e 1MBBIOS e One 16 bit ISA expansion slot e One VESA expansion slot e Real time clock calendar e Built in SMC651 for IDE HDD and FDD interface Overview 1 1 Built in PDC20230 local IDE interface Two serial ports and one parallel port PS 2 mouse and keyboard connector Built in Cirrus GD5426 GD5428 VGA with 1 or 2MB Video RAM on board LPM size board Overview Motherboard Layout oS 051287 SIMM4 87958 LO NI ma 56008 21075 9tvsao 9UXNIGT hil TIT EEE Overview System Block Diagram ViSExpansion slot VGA Connector 6
33. r Insert the drivers diskette into Drive A Run the installation program INSTALL EXE and choose the option for the drivers and specify the drive and directory where you want them copied to such as B GEM 3 requires that the drivers be installed from the root directory of a floppy disk in drive A Be sure to install the drivers to the root of drive A or drive B and then place the diskette in drive A before proceeding Install GEM 3 following the instructionsprovided in the product s manual selecting the standard IBM VGA Color IBM PS 2 driver After successfully completing installation insert the GEM 3 System Master Disk in drive A Move to drive A by typing A Enter Please note that you must install from the A drive Then type GEMSETUP Enter Follow the GEM 3 installation instructions up to the CHANGE EXISTING CONFIGURATION stage When prompted for a screen driver choice highlight OTHER DRIVER PACK When prompted to insert a screen driver into drive A insert the newly created GEM DRIVRPK diskette Select one of the following Cirrus Logic VGA 16 Color 800x600 Cirrus Logic VGA 16 Color 1024x768 10 Continue with the remainder of the installation UTILITY and DRIVERS Lotus 2 3 2 x 1 Run the installation program INSTALL EXE and choose the option for the Lotus 1 4 3 and specify the drive and directory where you want them copied to such as CALOTU
34. s Connector Side pins and pinouts Side B pins and pinouts NOTE The 120 pin slot connector pinout has been modified If it is used with a standard 120 pin slot card it may not work properly Table 2 7 ISA VESA Slot Connector Continued M otherboard Settings 2 9 Chapter 3 System Memory Total Memory Bank 1 Bank 3 1MB 2MB 1MB 3MB 1MB 4MB 1MB 4MB 5MB 1MB 6MB 1MB 7MB 1MB 8MB 4MB 12MB 4MB 16MB 4MB 16MB 17MB 1MB 18MB 1MB 19MB 1MB 20MB 4MB 21MB 4MB 22MB 4MB 24MB 4MB 28MB 4MB 32MB 16MB 33MB 16MB 34MB 16MB 36MB 16MB 40MB 16MB 48MB 16MB 64MB 16MB ret Table 3 1 Memory Configuration NOTE All memory banks use the 72 pin memory modules System Memory 3 1 64K 128 256K ALTER 8Kx 8 8Kx 8 32Kx 8 TAG RAM 8Kx 8 8Kx 8 32Kx 8 ata 38 saxe gt Table 3 2 Cache Configuration Size Figure 3 1 Cache Bank Location on the Motherboard System Memory 64K Direct Mapped Cache M7 8Kx8 M2 b 8 8 M8 8Kx8 M3 8Kx8 M9 8Kx8 M4 8 8 Figure 3 2 64K Direct Mapped Cache NOTE 64K Direct Mapped Cache option is achieved by installing eight 8Kx8 SRAM DATA RAM DIPs at M2 to M5 and M7 to M10 and one 8Kx8 SRAM TAG RAM 28 pin at M6 EE System
35. t UTILITY and DRIVERS 6 3 Getting Help Clmode provides Help for the following items Monitor Video Mode Preview Mouse Keyboard and About Clmode The Monitor Type help window explains the different capabilities of each monitor type The Video Mode help window defines the information given in the Video Mode window The Keyboard and Mouse help windows explain how to use the keyboard and the mouse to make selections The About window displays the copyright message and the Clmode version number Exiting the Clmode To exit Clmode at any time choose any of the following e Press Alt and F4 keys simultaneously e Click the left mouse button on the system button of the main window 1 The top left corner button of the window which is shown as a dot e Select the Exit button When the Clmode utility exits the current video mode monitor type and VGA refresh rate will be displayed 6 4 UTILITY and DRNERS Using Clmode s Command Line Options When command line options for CLMODE EXE are given at the DOS prompt the menu driven windows will not be displayed Instead monitor type video mode and refresh rate will be set at the DOS prompt The command line options for CLMODE EXE are CLMODE m montype I t6zx t8zx t1 x t2 x modenum mode number selects 400 lines default selects 350 lines selects 200 lines montype monitor type t6 x Hz 640x480 0 60 1 7
36. the beginning of the original command line Change VVGA SYS in the pasted command line to CLVSVGA SYS Select Save from the File menu and save the changes Double click on the SYSTEM icon to exit the editor Shutdown the system and reboot for the changes to take effect UTILITY and DRIVERS 6 15 Windows 3 0 drivers for OS 2 2 0 This section assumes that the WIN OS 2 Support has been installed If that option has not been selected at the initial OS 2 installation please use the Selective Install utility that is in the System Setup folder to first install WIN OS 2 Support 1 If you do not currently have a WIN OS 2 session running start one Open a WIN OS 2 session by double clicking on a WIN OS 2 icon from the OS 2 Command Prompts folder The Command Prompts icon is in the OS 2 System folder 2 Run the Install program to copy the WIN OS 2 Drivers and SetRES Utility to the hard disk In the Program Manager choose File Run Specify the diskette drive where the Drivers and Utilities for OS 2 Diskette is inserted and run the install program A UNSTALL Enter 3 When prompted specify to copy the files to the OS2 MDOS WINOS2 directory 4 The resolution may now be selected by running the SetRES Utility Execute SetRES by double clicking on the SetRES icon Use the SetRES utility to select either 16 or 256 colors and the desired resolution for future Win OS 2 sessions For help on the SetRES utility select Help from the program
37. u may also press Esc to abort the selection and not enter a password To disable your password press Enter when you are prompted to enter password A message appears confirming the password has been disabled When the password is disabled the system boots and you can enter SETUP freely Security Option If you select System under this field you will be prompted for the password every time system is rebooted or any time you try to enter SETUP If you select Setup you will be prompted only when you try to enter SETUP AA APANG 4 4 Award BIOS Setup Standard CMOS SETUP AMI BIOS SETUP PROGRAM STANDARD CMOS SETUP 0 1992 American Megatrends Inc All Rights Reserved Date mn date year Fri Jun 11 1993 Base memory 640 KB Time hour min sec 11 32 03 Ext memory 3072 KB Cyln Head WPcom LZone Sect Size Hard Disk C Type 17 977 5 300 977 17 41 Hard Disk D Not Installed Floppy Drive 1 2MB 5 4 Floppy Drive B Not Installed Primary Display VGA PGA EGA Sun Mon Tue Wed Thu Fri Sat 26 27 28 29 30 31 1 Keyboard Installed po 5 Month Jan Feb Dec 18 20 Date 01 02 03 31 25 27 Year 1901 1902 2099 2 4 ESC Exit 4 1 Select F2 F3 Color PgUp PgDn Modify The standard CMOS SETUP screen is shown above System BIOS automatically detects memory size thus no changes are necessary After the changes are made press Esc to exit The SETUP program is
38. very Time Disabled On board Serial Port 1 COMI Extended ALE Dirabled On board Serial Port 2 COM2 Decoupled Refresh Enabled On board Parallel Port 378 Relocate 256 384K Disabled Local IDE Select Disabled Video BIOS Cacheable Enabled System BIOS Cacheable Enabled DRAM Timing Control Fast Cache Timing Control Turbo Esc Quit Tio Select Item Fl Help PgUp PgDn Modify F5 Old Valuer Shift F2 Color F6 Load BIOS Defaults F7 Load Setup Defaults NOTE Users are not encouraged to run the BIOS and Chipset Features Setup items Your system should have been fine tuned before shipping Improper Setup may cause system to fail Consult dealer before making any changes Default values of the various Setup items on this chapter may not necessarily be the same ones shown on your screen Award BIOS Setup 4 3 Load Setup Default Selecting this field loads the factory defaults for BIOS and CHIPSET FEATURE which the system automatically detects Load BIOS Default BIOS defaults contain the most appropriate values of the system parameter that allows minimum system performance The OEM manufacturer may change the defaults through MODBIN before the binary image burns into the ROM Password Setting Select this function to create a password Type your password up to eight characters and press Enter You will be asked to confirm the password Type the password again and press Enter Yo
Download Pdf Manuals
Related Search