Home

Aldoor Manual - Aluminium Connection

image

Contents

1. N 0 Fit 2 jamb brackets to each vertical track using the supplied 5mm keep screws and nuts as shown in fig 8 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 17 ALDOOR OVERHEAD GARAGE DOOR conway SETTING UP VERTICAL TRACKS amp BOTTOM PANEL SINGLE AND DOUBLE DOOR eee a N AW z Se Nw T 3mm 1 Place 4 rollers into the assembled bottom panel amp position it in the opening so that each edge overlaps the edge of the jamb equally on both sides 2 With the rollers in position in the tracks position each track assembly so that there is 3mm between the roller and roller insert Fig 9 3 Tighten the bolts holding the L brackets and jambs 4 Press the track forward until the wing of the roller inserts touches the jamb 5 Use a spirit level to ensure that the track is vertical amp tighten the keep screws and bolts holding the tracks to the L brackets Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 18 ALDOOR OVERHEAD GARAGE DOOR conway SIDE SEAL HOLDERS SINGLE AND DOUBLE DOOR __ Fixing Screw i Wall i ee Li __ Timber SN _ Rubber x 4 Side seal EM A a L
2. crealco ALDOOR OVERHEAD GARAGE DOOR PROFILE IDENTIFICATION DOUBLE DOOR OrnmVwatls Aluminium Profile Stockists 155 50 157 00 ata r 5 Cf U J wu I LCL Fg 2 uU SN d NN M g S 7 Wo ALDOOR ALDOOR TOP PANEL STANDARD PANEL 1 at 4 94m 6 at 4 94m W31813 W31815 172 50 uu w l lt H NI a 7 N pan M U y i od J cul Jj V ALDOOR BOTIOM PANEL 1 at 4 94m W55586 157 00 A an l m t N Dit 59 46 NU a 8 c d 7 i E 3 9 v ALDOOR ALDOOR SIDE amp TOP JAMB BLACK H D PANEL 4 at 2 5m 7 at 4 94m W32101 W55593 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved yp crealco PAGE 6 ALDOOR OVERHEAD GARAGE DOOR conway Aluminium Profile Stockists HARDWARE KIT DOUBLE DOOR TORSION SPRING SYSTEM ALDHWKITDBL tem Description Picture Qty per tem Description Picture Qty per No Stock Code Box No Stock Code Box 1 Top Roller Brkt d 13 Aluminium Door Single Door 2 Roller Insert Kit LH 15 bag BRKTOP 1 ALROLINSERTLHKIT 2 Nylon Roller 2 14 Aluminium Door 11 Ball Heavy Roller Insert Kit RH 15 bag White 62 ALROLINSERTRHKIT ROLLER 2N10 3 Vert Track Brkt 15 Aluminium Door Y No J1 Hinge Clip 70 bag BRKLJO1 VIRAK 4 ALHINGEKIT D 4 Lift Cable 3 2 3800 Tension Sp CABLE L TORS213 D 16 Aluminium Door Fl
3. Headroom min 385mm o aso Side reveal min 250mm Side reveal min 350mm QU with 12 track with 12 track e NL 850 0 N l J J CT H 2 2440 0 J L 2440 0 H Y E OS DO EO Xx Sd SOS D zo Ds SSO SOS x D DDS 2135 0 rt iB Mb ode cde GbR RP NEP Ly SIC L JA Single Door with motor JAH 250 0 Headroom min 385mm 250 0 Side reveal min 250mm n with 12 track P H i H RUIN 2440 0 d 4 H Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 9 crealco ALDOOR OVERHEAD GARAGE DOOR EE CR SIDE VIEW OF MECHANISM SINGLE DOOR Tension Spring Assembly Cable Clamp oe Punched strip Spring Pulley S Hook amp Chain Moving Spring Anchor SOLUTO TEQUILA e e Spring Safety Cable Tension Spring Horizontal Track Track Pulley Fixed Flag Header Bracket ALDOOR OVERHEAD GARAGE DOOR SIDE VIEW OF MECHANISM DOUBLE DOOR Tension Spring Assembly Black RHS Red LHS ed Torsion fasion Black Cable Drum Cable Drum Cone spy spring Cone E pring 75mm Minimum domm k i Left Hand Side Zh 00 RN i Bearing Plate Spring Th o ene Torsion l
4. Side seal holder y PA Vertical Track S Assembly Fig 10 Bottom Panel Assembly 1 Position the side seal holders flush against the edge of the opening as shown in Fig 10 The bottom edge of the seal holder should rest against the floor 2 If needed trim the top of each seal holder to length The top of the seal holder should extend approximately 30mm above the top of the opening 3 Attach the seal holder to the jamb using the supplied 8x90 lag screws 4 Slide the rubber side seal into the seal holder as shown Fig 10 amp trim of any excess PAGE 19 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO ALDOOR OVERHEAD GARAGE DOOR TOP JAMBS SINGLE AND DOUBLE DOOR OrnmVwatljs Aluminium Profile Stockists al Screw and Wallplug Top Jamb Top Seal Pe Top Seal 1 Position the top Jamb against the top edge of the opening as shown in Fig 11 If needed trim the aluminium so that it fits in between the 2 side jambs Fix in place using 8x90 Lag screws 2 Slide the top seal into place The same rubber profile is used for both the side amp top seals Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 20 ALDOOR OVERHEAD GARAGE DOOR conway PLACE REMAINING PANELS IN TRACK SINGLE AND DOUBLE DOOR Insert rollers into each panel a
5. Identification s Tube Right Hand Side Horizontal gt i n de Colour Code Bolts Bearing Bearing Plate 0 H Top Roller _ TFT i Top Panel i Bracket INSIDE n Vertical i Track Track Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 10 ALDOOR OVERHEAD GARAGE DOOR HARDWARE KIT ALDHWKITSGL SINGLE DOOR Description 254 mm Radius Double we G T rack Horizontal Track Assembly B Gon Code CODFBVWeREJ Aluminium Profile Stockists Stock Code 8v LN 4 TRAKHZ10 240 5 Colour Code Horizontal Angle Colour Code Colour Code RT ad Vertical Track 4 TRAKVT2035 045 Par Eg c ees Colour Code ss S c eem c um EH Hardware Box for ALDHWKITSGL 1 Wispeco Single Size ALDoor Tension Spring System One Profile Kit Single Door Top Jamb Seal 2 Standard n TopSeal 1 Bottom 3m length Timber ALDTIMJAMBSGL 65kg Tension Springs RED i A 4 SPRO65 213 TENS Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 11 yp crealco ALDOOR OVERHEAD GARAGE DOOR HARDWARE KIT ALDHWKITDBL DOUBLE DOOR Description Stock Code le 277 me 254 mm Radius Double 4 TRAKHZ10 240 D Es Horizontal T rack Horizontal Track Assembly m NIE Colour Code Colour Code Horizontal Angle Oras Est
6. The tracks must not converge towards one another or diverge away from each other Fig 14 3 Support the rear of the tracks with wall brackets Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 23 ALDOOR OVERHEAD GARAGE DOOR oOonWweatjs Aluminium Profile Stockists TENSION SPRING ASSEMBLY SINGLE DOOR Moving Pulley Wheel Spring Mounted Spring Anchor Bracket B S Hook Chain Spring Tensioning System Cable Clamp Punched Strip Spring Safety Cable J Fig 15 Door Lifting Cable Wire Rope Fixed Pulley Wheel Tack Mounted unm m m em m mu Warning Warning Warning Exercise extreme caution when working with garage door springs There is a great deal of energy stored in the spring when it is under tension 1 Assemble the pulley with the fork to one end of each spring 2 Attach the spring anchor bracket the the horizontal tracks as shown 3 Hook one end of each chain onto the spring anchor brackets 4 Bolt the fixed pulley to the horizontal track as shown 5 Fit the pre formed loop on one end of the lifting cable to the pin on the bottom lifting brackets 6 Guide the lifting cable up the side of the door making sure that the cable runs between the edge of the door and the wings of the rolle
7. rivets 2 Slide the bottom seal into place 3 Firmly push the roller insert into place as shown The roller inserts are handed and marked I for the left hand side amp R for the right hand side of the door 4 Note R and L is looked at the door from the inside Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 13 ALDOOR OVERHEAD GARAGE DOOR TOP PANEL ASSEMBLY SINGLE DOOR Orna Aluminium Profile Stockists Panel Center Line Am ul Tovam Nee gt attachment plate LO Fig 2 Ay E flush Top roller bracket These edges flush st 1946 SX Top Panel Tow arm attachment plate 1 Place the door tow arm bracket in place as shown in fig 2 The top edge of the bracket must be flush with the top edge of the mounting flange on the panel 2 Using the pre drilled holes in the Tow arm attach plate drill 6 xmm holes through the mounting flanges and rivit the bracket in place only through the 4 corner holes for now Fig 3 3 Place the tow arm bracket in place as shown in fig 3 Rivit in place using the remaining holes 4 Place the 2 top roller brackets in place Fig 4 and arill through the pre punched holes and rivit in place The adjustable part of the bracket must be facing upwards 5 Finally slide the top seal into place Disclaimer The right to make alterations is rese
8. 1946 Aluminium Profile Stockists ev EN Colour Code Colour Code Vertical Track 4 TRAKVT2035 045 T i se M Colour Code ss c c c c se c um SS S S Hardware Box for ALDHWKITDBL Wispeco Double size ALDoor Torsion Spring System Torsion Springs RED Corne LHS of Door 4 SPR 060 213 LH Cone Colour Spring Colour ORANGE Red n LHS of Door Spring Colour Code Band BLACK h Cone RHS of Door 4 SPR 060 213 RH MOTELS cone coou Miu dde 5 Black RHS of Door Torsion Tube 4 TORSTUBE 5200 15 1 Length 5200 mm 3m length Timber ALDTIMJAMBDBL 3m length Timber ALDTIMJAMBSGL One Profile Kit Single Door Top Side Jamb Seal 2 Standard 6 Top Seal 2 Bottom 1 Box Panel 7 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C re a C O PAGE 12 ALDOOR OVERHEAD GARAGE DOOR conway BOTTOM PANEL ASSEMBLY SINGLE AND DOUBLE DOOR Top edge of bracket flush with mounting flange of panel Right hand side ee Insert shown 1 Attach the bottom corner lifting brackets to the panel as shown in Fig 1 Position the bracket so that the side tab is against the door panel amp the top edge of the bracket is flush with mounting flange Using the holes in the bracket as guides arill through the mounting flanges on the door panel and Then attach the brackets with the supplied 4 8mm x 15mm 50 pkt
9. 2x M8 x 40 Bolts Pg 19 i 8x M8 x 16 Bolts Pg 19 c 10x M5 Nuts Pg 19 an 16x M8 Pan Head Pg 11 13 m l x M5 Nuts Pg 11 13 1Ox M8 Washers Pg 19 iw 10x 8x30mm Wood Screws Pg 17 Bag 4FKWALL O1 Qty Description Where Used ES lag 8x60mm Wood Screws Pg 14 p x 8x90mm Wood Screws Pg 13 5x 8x50mm Plugs Pg 13 14 Bag 4FKWALL O2 Qty Description Where Used EA gy 8x60mm Wood Screws Pg 14 fim 18x 8x90mm Wood Screws Pg 13 24x 8x50mm Plugs Pg 13 14 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 8 yp crealco ALDOOR OVERHEAD GARAGE DOOR HEAD ROOM amp REVEAL AS SEEN FROM INSIDE onways Est 1946 Aluminium Profile Stockists F E F FEF FF CHR FF 3 b cup owe F F F F FF t te k o4 46 c i yt ot tt o c oo oo eB be Ee X4 oo pocBe wo coe poc cESGSEL deo dee Se om c ee deo ei yh f 47 Q J Double Door with motor See pm S Headroom min 485mm pr e Side reveal min 350mm m N A n E with 12 track P E 4880 0 ines Y JE 3o Os Xo SOS uo x ODS ere i CES 3o SSN OTSESESSE D x ower E SP FF SS FS FF SE B GB oc YF or SE cR F de Go d GO BO ode odo code e BB ge 30 ot t c E t o d Bo Ft HF F E A cy p Em d Single Door with motor Single Door with motor Fou Headroom min 385mm
10. Stock Code Box No Stock Code Box Top Roller Brkt 12 Chain Hooks Single Door 2 S and W Types oxy BRKTOP 1 S Nylon Roller 2 43 Aluminium Door 11 Ball Heavy Tow Arm Attach Bracket White ALTOWBRKT ROLLER 2N10 E Vert Track Brkt 14 Aluminium Door No JI Roller Insert Kit LH 15 bag BRKLJOT VTRAK Lift Cable 3 2 3800 Tension Sp CABLE L TENS213 Sect Door Sfly Cable Tension Sp CABLE SFTYTENS ALROLINSERTLHKIT Aluminium Door Roller Insert Kit RH 15 bag ALROLINSERTRHKIT Aluminium Door Hinge Clip 42 bag ALHINGEKIT 3 Pulley Plastic Fork Sprg PULLEY3P SPRG 3 Pulley Plastic Track Mount for Wispeco AlDoor Pulley3P ALDTRAK Anchor Bracket Spring Horizontal T Rack BRKANCHR SPRG 19 OY OC OC 20 Wispeco AlDoor Top Seal ALSEAL TOP Wispeco AlDoor Bottom Seal ALSEALBOT 10 Aluminium Door Bottom Lifting Bracket ALBRKTBOT 1 Aluminium Door Flag Bracket ALFLAGBRKT C Oi Gr x Poir LH amp R 3 Track Fastener amp Accessories Bag Complete Bag 4FKTRAK OT1 Pop Rivet Kit A 8mmx1 2mm 50 pkt 4FRPA812ASFL Wall Fastener Bag 4FKWALL O1 Im CP Manuals amp Labels Installation Manual MANUAL O9AL 63 22 Meters y 9 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 5 O OIoOo o Wispeco Silver Sticker ALSTICKER
11. ag Bracket ALFLAGBRKT g E Es go Es 5 Side Bearing EBF338 Track Fastener amp 17 BRGSIDE 338 1 OIE Accessories Bag Complete Bag AFKTRAK O2 6 Centre Bearing 18 Pop Rivet kit 338 11 Gauge 4 8mmx1 2mm 50 pkt g c BRGCNTR 338 1 AFRP48 1 2ASFL 19 wall Fastener Bag 7 Cable Drum Standard 4FKWALL O2 Size 400 8 DRUM408 Manuals amp Labels Installation Manual MANUAL O9AL LHS amp RHS Red amp Black 8 Wispeco AlDoor Top Wispeco Silver Sticker my Q Seal u lt E ALSTICKER Wispeco AlDoor Bottom Seal ALSEALBOT pe 10 Aluminium Door Bottom Lifting Bracket _ ALBRKTBOT Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved d C re a CO PAGE 7 ALDOOR OVERHEAD GARAGE DOOR BOLT BAG HARDWARE IDENTIFICATION Conways Aluminium Profile Stockists Bag 4FKTRAK O1 Qty Description Where Used 8x M8 x 16 Bolts Pg 19 cn 8x M8 Nuts Pg 19 4n l x M5 Pan Head Pg 11 13 m l x M5 Nuts Pg 11 13 112x M8 Washers Pg 19 Lo 9 4x Plate Pg 19 E gt gx 8x30mm Wood Screws Pg 17 2x S Hook Pg 19 CODOD 2X Chain Pg 19 Bag 4FKTRAK 02 Qty Description Where Used i
12. ant system The manual must also be used in conjunction with the design and cutting list from the latest version of StarFront crealco EXE LEGAL DISCLAIMER All information recommendations or advice contained in this documentation is given in good faith to the best of Wispeco s knowledge and is based on current procedures in effect Since the actual use of this documentation by the user is beyond the control of Wispeco such use is within the exclusive responsibility of the user Wispeco cannot be held responsible for any loss incurred through incorrect or faulty use of this documentation Great care has been taken to ensure that the information provided is correct Wispeco will accept no responsibility for any errors and or omissions which may have inadvertently occurred All mechanical joints must be sealed with a Wispeco approved joint sealer Laminated glass must not stand in water All drawings in the Wispeco Documentation are shown NOT to scale Wispeco cannot accept responsibility for the use of standard products since Wispeco does not know where these products are being installed The use of anti magnetic stainless steel screws and pop rivets is recommended to reduce galvanic corrosion in harsh environments The hardware recommended in this documentation is suitable for use in most atmospheric environments When hardware is used in severe costal environments the manufacturer of the hardware must be consulted Fixing l
13. ay particular attention to Track Hanger Brackets and Spring Anchor brackets 3 Make sure the Door Lifting Cables and the Safety Cables are secure Warning TENSION SPRINGS Do not attempt to adjust the spring tension whilst the door is in the closed position When the door is closed the spring is under maximum tension Raise the door before making any adjustments to the springs Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved d C rea CO PAGE 25 ALDOOR OVERHEAD GARAGE DOOR TORSION TUBE ASSEMBLY DOUBLE DOOR Centre Bearing Fixing bolts to pass through the wall Torsion Spring Fig 18 Cut away corner of LAN bearing plate faces downwards Assemble the torsion tube on the floor Slide the center bearing onto the tube up to the middle point onways Est 1946 Aluminium Profile Stockists Side Bearing 1 ca Cable Drum Torsion Tube Horizontal Track Angle Door Lifting Cable Fig 19 N l 2 3 Slide the torsion springs onto the tube with the stationary cones towards the center bearing 4 Slide the two cable drums onto the tube with the Red drum to the left hand side and the Black drum to the right hand side of the center bearing Slide the two side bearings onto the tube NOTE e 1 The Red winding cone is on the left hand side of the center bearing and the Black one to the
14. itial wind and then unwound to allow the springs to settle in The manufacturers spring information card should state the number of turns to be wound onto the spring 3 Draw a straight chalk line along the length of the spring Fig 21 This will assist in counting the number of turns being applied 4 Lubricate the spring Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 27
15. mp slide them into place from the top of the vertical tracks making sure that the edges of all the panels are flush 2 The lock panel should be the 6th panel from the floor Do not place the top panel in place yet 4 For a Single Door rotate the plastic hinge clips into place as shown in fig 12 There are three clips per panel 1 in the center and 2 at either end See the layout diagram on page 3 5 For a Double Door rotate the plastic hinge clips into place as shown in fig 12 There are five clips per panel 1 in the center and 2 at either end See the layout diagram on page 3 Co Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 21 ALDOOR OVERHEAD GARAGE DOOR COLES SETTING UP HORIZONTAL TRACKS SINGLE AND DOUBLE DOOR 1 While supporting the rear of the horizontal track place the track in position as shown in fig 13 Fix the curved section to the lower part of the flag bracket 2 Attach the horizontal track angle to the top part of the flag bracket as shown Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 22 ALDOOR OVERHEAD GARAGE DOOR conway ALIGN THE HORIZONTAL TRACKS SINGLE AND DOUBLE DOOR lt Correct Door Correct The tracks must be the same height from the floor and parallel to each other Fig 14 2
16. r inserts over the fixed track mounted pulley and through the moving spring mounted pulley as shown Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved d C rea l CO PAGE 24 ALDOOR AVE OVERHEAD GARAGE DOOR Ee TENSION SPRING ASSEMBLY SINGLE DOOR Cable Clamp Punched Strip S Hook Chain Spring Safety Cable Fig 17 7 Clamp the loose end of the lifting cable to the flag bracket using clamping plates as shown in Fig 16 8 Before the spring can be hooked to the spring anchor bracket the door must be lifted into the open position When the door is fully open secure it in place with a G clamp firmly attached to the track amp under the bottom panel 9 Pass the safety cable throught the center of the spring and fix one end to the flag bracket and the other end to the spring anchor bracket Note It is important that the safety cable is slack It s purpose is to contain the spring in the event that it breaks while under tension If the safety cable is not slack it may also break if the spring fails 10 Attach the spring to the chain using the S hook Fig 17 The tension of the spring can now be adjusted by changing the length of the chain Caution Caution Caution Before lifting the garage door check and re check the following 1 All fasteners are secure especially those that secure the jambs to the wall and the track fasteners 2 P
17. right hand side 2 The side bearings are left and right handed 3 Do not fix anything in place yet Lift the whole assembly into place 6 7 Bolt the side bearings to the horizontal track angles as shown Fig 19 8 Position the Center bearing over the packing block 9 Level the torsion tube and mark the positions of the fixing bolts for the center bearing 10 Drill 10mm holes through the wall and anchor the center bearing with long bolts 11 Be sure to allow the torsion tube to extend at least 75 mm beyond the side bearings at each end Fig 17 12 Attach the door lifting cables to the cable drums 13 Start with the left hand side drum Position the cable drum 20mm from the side bearing and fasten it to the torsion tube using the square headed screws provided on the drum 14 Be sure to allow the torsion tube to extend at least 75 mm beyond the side bearings at each end 15 Start with the left hand side drum Position the cable drum 20mm from the side bearing and fasten it to the torsion tube using the square headed screws provided on the drum 16 Rotate the torsion tube to take up the slack in the lifting cable Use a pair of Vice grips to prevent the torsion tube from turning Fig 17 17 Right hand side drum Position the cable drum 20mm from its side bearing Rotate the drum to take up the slack in the liffing cable Fasten the drum to the torsion tube Fig 19 TAKE NOTE It is very impo
18. rtant to make sure that the lifting cables are of the same length and that both have an equal amount of tension in them when the drums are fixed to the torsion tube Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved C rea CO PAGE 26 ALDOOR AVE OVERHEAD GARAGE DOOR Ee WINDING UP TORSION SPRINGS DOUBLE DOOR Spring Black RHS Identification Winding Cone Colour Code b Winding Direction Torsion Tube Assembly lt Winding Fig 20 Br VICE Grip 75mm Minimum 3mm Red LHS Winding Cone CAUTION CAUTION CAUTION Take great care when winding the springs Use only the correct type and size Winding Bars Two bars are required SPRING UNLOADED Do not use Screw Drivers or other ill fitting bars Never stand directly behind or below the bars when Sik ees Fig 2 winding the springs Never Never Never Apply more turns to the spring than the manufacturer stipulates on the Spring Information Card 1 Before winding up the springs make absolutely certain that all bearing plates are secure especially the center bearing NB The stored energy in the springs is great and very serious injuries may be sustained if incorrect procedures or inferior tools are used Only use the proper winding bars to wind the springs A strong and stable ladder must be used 2 It is recommended that the springs are given an in
19. rved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 14 d crealco ALDOOR OVERHEAD GARAGE DOOR COLES TOW ARM BRACKET ATTACHMENT DOUBLE DOOR TOP BOX PANEL Center line of Panel Tow Arm Bracket Brace Panel Fig 5 These edges flush A lt N Pd Top roller bracket Second Panel from Top Box Panel p Pu These edges EU flush 4 8 x 15mm Rivits Place the door tow arm bracket in place on one of the 4 brace panels on the center line of the panel as shown in fig 5 This panel will be installed second from the top 2 Using the pre drilled holes in the Tow arm attach bracket drill 3 x 5mm holes through the mounting flanges and the panel 3 Rivet the tow arm bracket in place using 3 x 4 8x15mm rivets fig 6 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 15 ALDOOR OVERHEAD GARAGE DOOR COLES ASSEMBLE REMAINING PANELS SINGLE AND DOUBLE DOOR All that remains to be done on the remaining panels is to push the roller inserts into place Fig 7 Note that the bottom panel has 4 roller inserts Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved y d C rea CO PAGE 16 ALDOOR OVERHEAD GARAGE DOOR conway ASSEMBLE THE VERTICAL TRACKS SINGLE AND DOUBLE DOOR Fig 8 Pan head KEP Screw a Horizontal Jamb Track Brackets NN E Bottom
20. ugs on frames must be positioned as per the user manual and used in accordance to the AAAMSA specifications When profiles are screwed together the screw centers must also be according to the user manual All glass used within Wispeco products must comply with SAGGA regulations All glazing above 10m from ground level must be signed off by a competent person Glazing in accordance with the national building regulations By continuing to use this documentation you acknowledge that you understand and accept the legal disclaimer Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 3 ALDOOR OVERHEAD GARAGE DOOR PROFILE IDENTIFICATION SINGLE DOOR 155 50 OrnmVwatls Aluminium Profile Stockists 157 00 39 50 a ALDOOR TOP PANEL 1 at 2 5m W31813 39 50 Ps 172 50 ALDOOR STANDARD PANEL 13 at 2 5m W31815 34 50 J Lt SN JJ i ALDOOR BOITOM PANEL 1 at 2 5m W55586 59 46 16 45 ALDOOR SIDE amp TOP JAMB 3 at 2 5m W32101 Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 4 yp crealco ALDOOR OVERHEAD GARAGE DOOR HARDWARE KIT Ornwalklhjs Est 1946 Aluminium Profile Stockists SINGLE DOOR TENSION SPRING SYSTEM ALDHWKITSGL Item Description Picture Qty per tem Description Picture Qty per No
21. ye crealco EXE ALDOOR OVERHEAD GARAGE DOOR PRODUCT MANUAL laimer The right to make alterations i 2013 Wispeco Pty Ltd All Rights Reserved Revision October 2013 Index Legal Disclaimer Profile Identification Single Door Hardware Kit Tension Spring System Profile Identification Double Door Hardware Kit Torsion Spring System Bolt Bag Hardware Identification Head Room amp Reveal Side View of Mechanism Single and Double Door Hardware Kit Single Door Hardware Kit Double Door Bottom Panel Assembly Single and Double Door Top Panel Assembly Single Door Tow Arm Bracket Attachment Double Door Top Box Panel Assembly Remaining Panels Single and Double Door Assembly the Vertical Tracks Single and Double Door Setting up Vertical Tracks amp Bottom Panel Single and Double Door Side Seal Holders Single and Double Door Top Jambs Single and Double Door Place Remaining Panels in Track Single and Double Door Setting up Horizontal Tracks Single and Double Door Align the Horizontal Tracks Single and Double Door Tension Spring Assembly Single Door Torsion Tube Assembly Double Door Winding Up Torsion Springs Double Door Disclaimer The right to make alterations is reserved 2012 Wispeco Pty Ltd All Rights Reserved PAGE 2 crealco ZEEE This manual must be read in conjunction with the Installation Cleaning and Maintenance Document BEE Certificates and the Performance Certificates for the relev

Download Pdf Manuals

image

Related Search

Related Contents

CHS Series User`s Manual    Using the NVCA Phosphorus Loading Development Tool    取扱説明書(保証書別添)  Sony MDR-ZX100 User's Manual  Mode d`emploi de silgeneve.ch  Kanguru Solutions iNAS-100 User's Manual  Pure user guide - University of Bristol  EasyTracker: An Android application for capturing  

Copyright © All rights reserved.
Failed to retrieve file